Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Effects of thermal loading on foil and sheet composites with constituents of differing thermal expansivities.

A study was made to estimate the magnitudes of elastic stresses and elastic-plastic stresses and strains in sheet or foil laminar composites. Using a model tungsten/80Ni + 20Cr laminar composite and assuming cooling or heating through a temperature range of 80-2000 deg F (26.5-1093.5 deg C), calculated elastic stresses exceeded published or estimated strengths of the constituents. Elastic-plastic stress-strain solutions resulted in lower estimated stress levels but with the concomitant occurrence of sufficiently large strain ranges to suggest possible thermal fatigue problems. Limited experimental studies using tungsten/80Ni + 20Cr foil and sheet laminar composites, slowly cycled between 80 and 2000 deg F (26.5-1093.5 deg C) or rapidly cycled between 80 and 1600 deg F (26.5-871 deg C) produced varying degrees of observable structural damage in from 1 to 11 cycles depending upon temperature transition rate and laminae thickness; these particular results might not occur with other combinations of materials.

Hoffman, C. A.↗

Stress Mapping in Glass-to-Metal Seals using Indentation Crack Lengths.

Predicting the residual stress which develops during fabrication of a glass-to-metal compression seal requires material models that can accurately predict the effects of processing on the sealing glass. Validation of the predictions requires measurements on representative test geometries to accurately capture the interaction between the seal materials during a processing cycle required to form the seal, which consists of a temperature excursion through the glass transition temperature of the sealing glass. To this end, a concentric seal test geometry, referred to as a short cylinder seal, consisting of a stainless steel shell enveloping a commercial sealing glass disk has been designed, fabricated, and characterized as a model validation test geometry. To obtain data to test/validate finite element (FE) stress model predictions of this geometry, spatially-resolved residual stress was calculated from the measured lengths of the cracks emanating from radially positioned Vickers indents in the glass disk portion of the seal. The indentation crack length method is described, and the spatially-resolved residual stress determined experimentally are compared to FE stress predictions made using a nonlinear viscoelastic material model adapted to inorganic sealing glasses and an updated rate dependent material model for 304L stainless steel. The measurement method is a first to achieve a degree of success for measuring spatially resolved residual stress in a glass-bearing geometry and a favorable comparison between measurements and simulation was observed.

36 MATERIALS SCIENCE↗

Stress Mapping in Glass-to-Metal Seals using Indentation Crack Lengths

Predicting the residual stress which develops during fabrication of a glass-to-metal compression seal requires material models that can accurately predict the effects of processing on the sealing glass. Validation of the predictions requires measurements on representative test geometries to accurately capture the interaction between the seal materials during a processing cycle required to form the seal, which consists of a temperature excursion through the glass transition temperature of the sealing glass. To this end, a concentric seal test geometry, referred to as a short cylinder seal, consisting of a stainless steel shell enveloping a commercial sealing glass disk has been designed, fabricated, and characterized as a model validation test geometry. To obtain data to test/validate finite element (FE) stress model predictions of this geometry, spatially-resolved residual stress was calculated from the measured lengths of the cracks emanating from radially positioned Vickers indents in the glass disk portion of the seal. The indentation crack length method is described, and the spatially-resolved residual stress determined experimentally are compared to FE stress predictions made using a nonlinear viscoelastic material model adapted to inorganic sealing glasses and an updated rate dependent material model for 304L stainless steel. The measurement method is a first to achieve a degree of success for measuring spatially resolved residual stress in a glass-bearing geometry and a favorable comparison between measurements and simulation was observed.

36 MATERIALS SCIENCE↗

Martian lithospheric thickness from elastic flexure theory

The thickness of the elastic lithosphere in the Tharsis region of Mars is estimated from effects due to the surface load of Olympus Mons. Deformation (vertical displacement) and stress are calculated using elastic flexure theory for a range of possible lithospheric thicknesses (T), modeling the lithosphere as a thin elastic shell and the interior as a Newtonian fluid. For T below 150 km, displacement and stress rise rapidly with decreasing thickness. For T near 100 km, deformation of the region surrounding the volcano would be clearly visible in the topography, and resulting tensional stresses exceeding 5 kbar should produce observable fracturing at the surface. In contrast, for T near 200 km deformation is minimal and the tensional stress, being less than a kilobar, would not result in extensive fracturing. Since significant deformation and fracturing are not observed, it is concluded that the Martian elastic lithosphere is at least 150 km in thickness. Seismic, tectonic, and gravity observations all suggest a thick Martian lithosphere as well.

Thurber, C. H.↗

A new look at numerical analyses of free-edge stresses in composite laminates

The edge stress problem for a + or - 45 deg graphite/epoxy laminate was examined. The reliability of the displacement formulated finite element method in analyzing the edge stress problem was investigated. Analyses of two well known elasticity problems, one involving a stress discontinuity and one a singularity, showed that the finite element analysis yields accurate stress distributions everywhere except in two elements closest to the stress discontinuity of singularity. Stress distributions for a + or - 45 deg laminate showed the same behavior near the singularity found in the well known problems with exact solutions. The displacement formulated finite element method appears to be a highly accurate technique for calculating interlaminar stress in composite laminates. The disagreement among the numerical methods was attributed to the unsymmetric stress tensor at the singularity.

Raju, I. S.↗

Stress analysis and design considerations for Shuttle pointed autonomous research tool for astronomy /SPARTAN/

The Shuttle Pointed Autonomous Research Tool for Astronomy (SPARTAN) family of spacecraft are intended to operate with minimum interfaces with the U.S. Space Shuttle in order to increase flight opportunities. The SPARTAN I Spacecraft was designed to enhance structural capabilities and increase reliability. The approach followed results from work experience which evolved from sounding rocket projects. Structural models were developed to do the analyses necessary to satisfy safety requirements for Shuttle hardware. A loads analysis must also be performed. Stress analysis calculations will be performed on the main structural elements and subcomponents. Attention is given to design considerations and program definition, the schematic representation of a finite element model used for SPARTAN I spacecraft, details of loads analysis, the stress analysis, and fracture mechanics plan implications.

Ferragut, N. J.↗

Comparative energetics of carbon storage molecules in green algae

Several members of the green algae possess the ability to produce lipids and/or high value compounds in significant quantities. While for several of these green algal species induction of increased lipid production has been shown, and cultivation of species for high value molecules occurs at production scale, the molecular mechanisms governing over-accumulation of molecules synthesized from isoprenoid precursors, carotenoids, for example, have received far less attention. Here, we present a calculation of the required ATP equivalencies per carbon atom and reducing power equivalencies as NADH/NADPH (NAD(P)H) per carbon atom for the isoprenoid molecules ..beta..-carotene (C40), astaxanthin (C40), and squalene (C30). We compared energetic requirements of carbohydrates, triacylglycerol, and isoprenoid molecules under a gradient of conditions of cellular stress. Our calculations revealed slightly less ATP and NAD(P)H equivalency per carbon atom between triacylglycerol and the three isoprenoid molecules. Based on our results, we propose that the driving force for differences in accumulation patterns of carotenoids vs. triacylglycerols in algal cells under stress is largely dependent on the presence and regulation of bypass mechanisms at metabolic junction bottlenecks, like pyruvate dehydrogenase (PDH), within particular species. We provide a discussion of several molecular mechanisms that may influence carbon partitioning within different groups of green algae, including metabolic inhibition through accumulation of specific substrates related to ATP and reducing equivalent production (NAD(P)H) as well as cellular compartmentalization. This work contributes to the ongoing discussion of cellular homeostatic regulation during stress, as well as the potential mechanisms driving long-term carbon storage as it relates to energy and redox states within the algal cell.

09 BIOMASS FUELS↗

Flow strength of tantalum under ramp compression to 250 GPa

A magnetic loading technique was used to study the strength of polycrystalline tantalum ramp compressed to peak stresses between 60 and 250 GPa. Velocimetry was used to monitor the planar ramp compression and release of various tantalum samples. A wave profile analysis was then employed to determine the pressure-dependence of the average shear stress upon unloading at strain rates on the order of 10{sup 5} s{sup −1}. Experimental uncertainties were quantified using a Monte Carlo approach, where values of 5% in the estimated pressure and 9–17% in the shear stress were calculated. The measured deviatoric response was found to be in good agreement with existing lower pressure strength data as well as several strength models. Significant deviations between the experiments and models, however, were observed at higher pressures where shear stresses of up to 5 GPa were measured. Additionally, these data suggest a significant effect of the initial material processing on the high pressure strength. Heavily worked or sputtered samples were found to support up to a 30% higher shear stress upon release than an annealed material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of notched metal matrix composites under tension loading

Presented are techniques based on 3-D finite-element analysis for the examination of continuous fiber reinforced metal matrix composites. Examples are shown for specific metal matrix composites such as boron/aluminum and silicon-carbide/aluminum. Specimen stress-strain behavior and stress at first fiber failure were predicted for boron/aluminum laminates containing circular holes and crack-like slits. The predictions compared very well for (+ or - 45) sub 2s laminates. Mesh configuration was shown to have an effect on the calculation of stresses local to the notch. The presence of thin interface layers of matrix material had a significant influence on the slit-tip stress state, causing sharper stress gradients near the notch. Interface layers reduced the slit-tip fibers stresses in a (+ or - 45) sub s silicon-carbide/aluminum laminate but increased them in a (0/90) sub s laminate.

Bigelow, C. A.↗

Multilayer theory for delamination analysis of a composite curved bar subjected to end forces and end moments

A composite test specimen in the shape of a semicircular curved bar subjected to bending offers an excellent stress field for studying the open-mode delamination behavior of laminated composite materials. This is because the open-mode delamination nucleates at the midspan of the curved bar. The classical anisotropic elasticity theory was used to construct a multilayer theory for the calculations of the stress and deformation fields induced in the multilayered composite semicircular curved bar subjected to end forces and end moments. The radial location and intensity of the open-mode delamination stress were calculated and were compared with the results obtained from the anisotropic continuum theory and from the finite element method. The multilayer theory gave more accurate predictions of the location and the intensity of the open-mode delamination stress than those calculated from the anisotropic continuum theory.

Ko, William L.↗

Multilayer theory for delamination analysis of a composite curved bar subjected to end forces and end moments

A composite test specimen in the shape of a semicircular curved bar subjected to bending offers an excellent stress field for studying the open-mode delamination behavior of laminated composite materials. This is because the open-mode delamination nucleates at the midspan of the curved bar. The classical anisotropic elasticity theory was used to construct a 'multilayer' theory for the calculations of the stress and deformation fields induced in the multilayered composite semicircular curved bar subjected to end forces and end moments. The radial location and intensity of the open-mode delamination stress were calculated and were compared with the results obtained from the anisotropic continuum theory and from the finite element method. The multilayer theory gave more accurate predictions of the location and the intensity of the open-mode delamination stress than those calculated from the anisotropic continuum theory.

Ko, William L.↗

Stresses in a webbed ball

An experimental stress analysis was undertaken to evaluate stresses within cylindrically hollow reinforced webbed bearing balls proportioned for a 50 percent mass reduction. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models, which were statically loaded in various orientations. Results are reported for 127 mm (5 in.) outside diameter balls under 44,500 N (10,000 lb) loads. Similitude considerations permit these results to be applied to calculations of stresses in actual size drilled bearing balls proportioned to these mass reductions.

Nypan, L. J.↗

A Summary of Diagonal Tension Part I : Methods of Analysis

Previously published methods for stress and strength analysis of plane and curved shear webs working in diagonal tension are presented as a unified method. The treatment is sufficiently comprehensive and detailed to make the paper self-contained. Part 1 discusses the theory and methods for calculating the stresses and shear deflections of web systems as well as the strengths of the web, the stiffeners, and the riveting. Part 2, published separately, presents the experimental evidence. (author)

Kuhn, Paul↗

Stress Determination in Nickel Monosilicide Films Using X-ray Diffraction

Lattice spacing measurements of the (211)/(202), (020)/(013), and (111)/(102) reflections were used to calculate the residual stresses in a Ni monosilicide film after cooling from its formation temperature. The ability to measure stresses in crystalline materials using x-ray diffraction requires the use of appropriate x-ray elastic constants, which link the measured strain to the stress tensor of the grains that satisfy the diffraction condition. X-ray elastic constants were calculated in the Neerfeld-Hill (NH) limit for a polycrystalline aggregate composed of orthorhombic crystals. The anisotropy in grains that possess orthorhombic elasticity introduces significant variation in the stresses determined among the three sets of reflections. However, the in-plane stress calculated due to thermal expansion mismatch between NiSi and the underlying Si substrate shows a close correspondence to the average of x-ray measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Combined shape and topology optimization for minimization of maximal von Mises stress

Here, this work shows that a combined shape and topology optimization method can produce optimal 2D designs with minimal stress subject to a volume constraint. The method represents the surface explicitly and discretizes the domain into a simplicial complex which adapts both structural shape and topology. By performing repeated topology and shape optimizations and adaptive mesh updates, we can minimize the maximum von Mises stress using the p-norm stress measure with p-values as high as 30, provided that the stress is calculated with sufficient accuracy.

42 ENGINEERING↗

In-situ single-grain peak profile measurements on Ti-7Al during tensile deformation.

High-energy three-dimensional X-ray diffraction with medium and high reciprocal space resolution was applied to study in situ tensile deformation of Ti-7Al specimens. Samples with planar and random dislocation microstructures were prepared and characterized by electron microscopy. Stress tensors of individual grains were obtained at several loads up to 2% deformation. The stress tensors were found to rotate, and resolved shear stresses were calculated. High-resolution reciprocal space maps of selected grains were recorded. Azimuthal and radial distributions were visualized and discussed in terms of idealized dislocation structures. Heterogeneous grain rotations were observed for the planar microstructure and found to be consistent with activation of the highest stressed basal slip system. Intra-granular strain gradients were detected in excess of the intrinsic radial dislocation peak broadening. The potential of combining the applied techniques with modeling to obtain multiple length-scale information during deformation of bulk specimens is discussed.

36 MATERIALS SCIENCE↗

Damage Tolerance Analysis of Space Shuttle External Tank Lug Fillet Welds Using NASGRO

The damage tolerance of the External Tank (ET) lug welds were reassessed because of an increase in the loads due to the removal of the protuberance air load (PAT.,) ramp. The analysis methods included detailed finite element analysis (FEA) of the ET welded lugs and FEA of the lug weld test configuration. The FEA results were used as input to the crack growth analysis code NASGRO to calculate the mission life capability of the ET lug welds and to predict the number of cycles to failure in the lug weld testing. The presentation presents the method of transferring the FEM results to the NASGRO model and gives correlations between FEM and NASGRO stress intensity calculations.

Allen, Phillip A.↗

A combined ensemble-volume average homogenization method for lattice structures with defects under dynamic and static loading

In the study of lattices structures, both experiments and numerical simulations are often conducted with small samples. Using combined ensemble and volume averaging, this work introduces a method to extract a macroscopic constitutive response of a lattice material from numerical simulations performed in periodic domains. The domain size needed to obtain statistically accurate results is investigated. Similar to molecular dynamics, the concept of the virial stress is introduced after homogenized equations are derived using the ensemble averaging method. Under static conditions, the virial stress is shown to agree with the volume averaged solid stress. Using the homogenization method, constitutive relations for this stress can be obtained from systems with uniform strains. Application of such obtained constitutive relations to more general cases results in an error proportional to the square of the ratio between the lattice length scale and the macroscopic length scale. Taking advantage of this property, numerical simulations are performed in systems with a uniform gradient of the average velocity. The volume average method is then used to accelerate convergence when studying lattices with defects. To avoid the artificial numerical time scale from the size of a representative volume element divided by the wave speed, a numerical scheme is developed to enforce a spatially uniform velocity gradient within the computational domain while allowing fluctuations of the velocity or displacement to develop naturally. To account for probability distribution of lattice defects, the stress is calculated as the ensemble-volume averaged value. For dynamic systems, energy dissipation properties are also studied.

36 MATERIALS SCIENCE↗