Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solar Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Properties of reactively sputtered oxygenated cadmium sulfide (CdS:O) and their impact on CdTe solar cell performance

Oxygenated cadmium sulfide (CdS:O) is commonly used as the n-type window layer in high-performance CdTe heterojunction solar cells. This layer is deposited by reactive sputtering, but the optimal amount of oxygen in the sputtering ambient is highly dependent on the specific system and process employed. In this work, the intrinsic properties of CdS:O were measured as a function of the oxygen content (0%–10%) in the sputtering ambient and correlated to device performance with the goal of better defining optimal CdS:O properties for CdTe solar cells. Optimal performance was found using CdS:O films that contained ∼40 at. % oxygen as measured by Rutherford backscattering spectrometry. X-ray photoelectron spectroscopy confirmed these results and showed that oxygen is incorporated primarily as oxygenated sulfur compounds (SO{sub x}). Device efficiency improved from 10.5% using CdS to >14% with CdS:O due largely to increases in short-circuit current density as well as a modest improvement in open-circuit voltage. The transparency of the CdS:O films was well correlated with observed improvements in blue quantum efficiency with increasing oxygen content. The optical bandgap of as-deposited CdS:O was identified as a simple metric for process optimization and transfer, with 2.8 eV being ideal for the device architecture employed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Adaptive light management in solar cells

A solar cell system is formed with a dynamic surface relief grating. Movement members are actuated by a controller to produce a force on the reflective surface. The reflective surface deforms in response to the force creating a surface relief grating that can adapt to changing light conditions.

14 SOLAR ENERGY↗

Exciton fission enhanced silicon solar cell

While silicon solar cells dominate global photovoltaic energy production, their continued improvement is hindered by the single-junction limit. One possible solution is to use molecular singlet exciton fission to generate two electrons from each absorbed high-energy photon. We demonstrate that the long-standing challenge of coupling molecular excited states to silicon solar cells can be overcome using sequential charge transfer. Combining zinc phthalocyanine, aluminum oxide, and a shallow junction crystalline silicon microwire solar cell, the peak charge generation efficiency per photon absorbed in tetracene is (138% ± 6%), comfortably surpassing the quantum efficiency limit for conventional silicon solar cells and establishing a new, scalable approach to low-cost, high-efficiency photovoltaics.

14 SOLAR ENERGY↗

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices have used devices prepared by spin coating, a process that is not amenable to large-scale fabrication. This mismatch in device fabrication makes it difficult to translate quantitative results obtained in the laboratory to the commercial level, making optimization difficult. Using a mini-slot die coater, this mismatch can be resolved by translating the commercial process to the laboratory and characterizing the structure formation in the active layer of the device in real time and in situ as films are coated onto a substrate. The evolution of the morphology was characterized under different conditions, allowing us to propose a mechanism by which the structures form and grow. This mini-slot die coater offers a simple, convenient, material efficient route by which the morphology in the active layer can be optimized under industrially relevant conditions. The goal of this protocol is to show experimental details of how a solar cell device is fabricated using a mini-slot die coater and technical details of running in situ structure characterization using the mini-slot die coater.

14 SOLAR ENERGY↗

On-device lead sequestration for perovskite solar cells

Perovskite solar cells (PSCs) face obstacles on their way towards commercialization. Potential issues with lead toxicity and leaching from devices remain relatively unexplored. It is desirable to develop strategies that avoid potential Pb leakage to the environment, although enhanced physical encapsulation can lessen Pb leakage from devices when subjected to mild environmental damage. We present a new chemical approach for on-device sequestration (>96%) of lead leakage caused by severe device damage without sacrificing the efficiency and stability of PSCs under normal operation.

14 SOLAR ENERGY↗

Chemical Design of Organic Interface Modifiers for Highly Efficient and Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) have demonstrated rapid progress in their power conversion efficiencies (PCEs) - from 3.8% in 2009 to 25.7% in 2022 - and they have received considerable attention as a promising future photovoltaic (PV) technology. However, the operational stability of PSCs is still inadequate to satisfy the standards for commercial applications. Interface engineering has become one of the most important strategies to push PSCs' efficiency and stability for practical use. Among the various interface engineering approaches, organic interface modifiers (OIMs) have been frequently used by the PSC field to address the issues limiting PSC stability at high efficiency levels. In this perspective, the chemical structures of state-of-the-art OIMs are discussed, and their characteristics are reviewed, as well as the impact on device performance associated with key device interfaces (e.g., metal oxide/perovskite and organic transport layer/perovskite interfaces) from a chemical and materials engineering point of view is discussed. Finally, design considerations and the authors' perspective are discussed, on the basis of representative literature examples, for building new, customized organic OIMs to further improve PSC efficiency and stability toward commercialization.

14 SOLAR ENERGY↗

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. Here, we found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi–steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T85 at maximum power point under 1-sun illumination.

14 SOLAR ENERGY↗

Hole transport layer selection for stable and efficient carbon electrode-based perovskite solar cells

Perovskite solar cell (PSC) technology has achieved remarkable progress, with champion power conversion efficiencies (PCE) exceeding 26%. However, the long-term stability of PSCs remains a significant barrier to their widespread commercialization. Carbon-based PSCs (C-PSCs) have gained attention as a promising cost-effective and scalable production solution, replacing expensive metal electrodes and offering improved stability. Despite these advantages, C-PSCs face challenges in matching the performance of noble metal-based PSCs, particularly in terms of carrier extraction efficiency and reduced carrier recombination at the carbon/perovskite interface. The selection of hole transport materials (HTMs) is crucial for optimizing this interface, but comprehensive studies on HTM selection for C-PSCs are limited. This study systematically investigated three commonly used hole transport layers (HTLs): Spiro-OMeTAD, CuSCN, and PTAA. Our results show that Spiro-OMeTAD-based C-PSCs exhibit the best overall performance, achieving a PCE of 19.29%. CuSCN-based devices, while lower in efficiency (11.94% PCE), demonstrated superior stability, retaining approximately 60% of their initial performance after 500 hours under ambient conditions. PTAA-based devices achieved a PCE of 12.92% but exhibited significant degradation, maintaining only ∼35% of their original efficiency over the same duration. These findings highlight the importance of selecting HTLs that balance performance and stability and emphasize the need for further optimization to enhance the commercial viability of C-PSCs.

14 SOLAR ENERGY↗

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

X-ray beam induced current (XBIC) measurements allow mapping of the nanoscale performance of electronic devices such as solar cells. Ideally, XBIC is employed simultaneously with other techniques within a multi-modal X-ray microscopy approach. An example is given herein combining XBIC with X-ray fluorescence to enable point-by-point correlations of the electrical performance with chemical composition. For the highest signal-to-noise ratio in XBIC measurements, lock-in amplification plays a crucial role. By this approach, the X-ray beam is modulated by an optical chopper upstream of the sample. The modulated X-ray beam induced electrical signal is amplified and demodulated to the chopper frequency using a lock-in amplifier. By optimizing low-pass filter settings, modulation frequency, and amplification amplitudes, noise can efficiently be suppressed for the extraction of a clear XBIC signal. A similar setup can be used to measure the X-ray beam induced voltage (XBIV). Beyond standard XBIC/XBIV measurements, XBIC can be measured with bias light or bias voltage applied such that outdoor working conditions of solar cells can be reproduced during in-situ and operando measurements. Ultimately, the multi-modal and multi-dimensional evaluation of electronic devices at the nanoscale enables new insights into the complex dependencies between composition, structure, and performance, which is an important step towards solving the materials' paradigm.

14 SOLAR ENERGY↗

Correlations of Capacitance-Voltage Hysteresis with Thin-Film CdTe Solar Cell Performance During Accelerated Lifetime Testing

In this paper we present the correlation of CdTe solar cell performance with capacitance-voltage hysteresis, defined presently as the difference in capacitance measured at zero-volt bias when collecting such data with different pre-measurement bias conditions. These correlations were obtained on CdTe cells stressed under conditions of 1-sun illumination, open-circuit bias, and an accelerationtemperature of approximately 100 degrees C.

14 SOLAR ENERGY↗

A new strategy to engineer polymer bulk heterojunction solar cells with thick active layers via self-assembly of the tertiary columnar phase

Here, we report that the addition of a non-photoactive tertiary polymer phase in the binary bulk heterojunction (BHJ) polymer solar cell leads to a self-assembled columnar nanostructure, enhancing the charge mobilities and photovoltaic efficiency with surprisingly increased optimal active blend thicknesses over 300 nm, 3–4 times larger than that of the binary counterpart. Using the prototypical poly(3-hexylthiophene) (P3HT):fullerene blend as a model BHJ system, we discover that the inert poly(methyl methacrylate) (PMMA) added in the binary BHJ blend self-assembles into vertical columns, which not only template the phase segregation of electron acceptor fullerenes but also induce the out-of-plane rotation of the edge-on-orientated crystalline P3HT phase. Using complementary interrogation methods including neutron reflectivity, X-ray scattering, atomic force microscopy, transmission electron microscopy, and molecular dynamics simulations, we show that the enhanced charge transport originates from the more randomized molecular stacking of the P3HT phase and the spontaneous segregation of fullerenes at the P3HT/PMMA interface, driven by the high surface tension between the two polymeric components. The results demonstrate a potential method for increasing the thicknesses of high-performance polymer BHJ solar cells with improved photovoltaic efficiency, alleviating the burden of stringently controlling the ultrathin blend thickness during the roll-to-roll-type large-area manufacturing environment.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dielectric constant engineering of nonfullerene acceptors enables a record fill factor of 83.58% and a high efficiency of 20.80% in organic solar cells

Organic solar cells (OSCs) have achieved power conversion efficiencies (PCEs) surpassing 20%, but their development remains hindered by the inherently low dielectric constant (εr) of organic semiconductors, which limits charge transport and contributes to serious recombination losses. Herein, we present a comprehensive strategy to overcome the challenge by engineering the dielectric properties of nonfullerene acceptors (NFAs). Two Y-series NFAs of BTP-N3F and BTP-C3F have been synthesized featuring trifluoromethyl (CF 3 ) end-capped alkyl side chains. This molecular design significantly enhances the dipole moment and ε r (up to ∼5.9) when compared to the reference acceptor Y6 (∼3), reducing the exciton binding energy (E b ) and improving charge transport. Furthermore, the incorporation of a high-εr polymer additive, poly(pentafluorostyrene) (PPFS), synergistically improves the active layer morphology and dielectric properties, enabling efficient charge extraction and reduced recombination losses. Devices based on the optimized D18-Cl/BTP-C3F system have achieved a record-high fill factor (FF) of 83.58% and an impressive PCE of 20.80%, setting a new benchmark for OSCs. Finally, our results underscore the pivotal role of ε r in enhancing device performance and establish a versatile pathway for advancing OSC efficiency and stability through molecular and morphological optimization.

36 MATERIALS SCIENCE↗

Recent advances of two-dimensional material additives in hybrid perovskite solar cells

Perovskite solar cells (PSCs) have become one of the state-of-the-art photovoltaic technologies due to their facile solution-based fabrication processes combined with extremely high photovoltaic performance originating from excellent optoelectronic properties such as strong light absorption, high charge mobility, long free charge carrier diffusion length, and tunable direct bandgap. However, the poor intrinsic stability of hybrid perovskites under environmental stresses including light, heat, and moisture, which is often associated with high defect density in the perovskite, has limited the large-scale commercialization and deployment of PSCs. The use of process additives, which can be included in various subcomponent layers in the PSC, has been identified as one of the effective approaches that can address these issues and improve the photovoltaic performance. Among various additives that have been explored, two-dimensional (2D) materials have emerged recently due to their unique structures and properties that can enhance the photovoltaic performance and device stability by improving perovskite crystallization, defect passivation, and charge transport. In this work, we provide a review of the recent progresses in 2D material additives for improving the PSC performance based on key representative 2D material systems, including graphene and its derivatives, transitional metal dichalcogenides, and black phosphorous, providing a useful guideline for further exploiting unique nanomaterial additives for more efficient and stable PSCs in the near future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

V-grooved silicon solar cells

Silicon solar cells with macroscopic V-shaped grooves and microscopically texturized surfaces were made by preferential etching techniques. Various conditions for potassium hydroxide and hydrazine hydrate etching were investigated. Optical reflection losses from these surface were reduced. The reduced reflection occurred at all wavelengths and resulted in improved short circuit current and spectral response. Improved collection efficiency is also expected from this structure due to generation of carriers closer to the cell junction. Microscopic point measurements of collected current using a scanning electron microscope showed that current collected at the peaks of the texturized surface were only 80 percent of those collected in the valleys.

Baraona, C. R.↗