Search NASA⌕ Search

SEARCH · Search NASA

Results for “Spray Forming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Radiation Shielding Plasma Sprayed Coatings Heads to International Space Station for MISSE-17 Experiments

NASA's Artemis program aims to return to the moon in search of scientific discoveries and establish a habitat using in-situ resource utilization. However, the past lunar explorations presented challenges, such as thermal cycles, solar and intergalactic cosmic radiation, and severe abrasive interaction of sharp lunar regolith particles[1]–[4].Dust mitigation and radiation shielding have become the most important concerns for lunar structural components and rovers which can fail abruptly without a protective solution. To counter these threats, Plasma Forming Laboratory(PFL) at Florida International University (FIU), in collaboration with NASA, has developed a novel multi-functional coating to protect the components synergistically against abrasion, erosion ,and radiation. The titanium-boron nitride composite coatings were prepared using the atmospheric plasma spray technique from engineered composite powders [5], [6].The coatings were subjected to extensive characterization and tribological study with lunar mare simulant JSC-1A, which shows tremendous improvement in the wear performance. The coatings subjected to neutron radiation shielding experiments at NASA Langley Research Center exhibited significantly improved neutron attenuation capacity compared to the substrate. The coating is selected to undergo radiation exposure on the International Space Station as a part of MISSE-17 (Materials International Space Station Experiment).

Thermal Spray↗

High Velocity Oxygen Fuel Spraying of Erosion and Wear Resistant Coatings on Jet Engine Parts

High velocity oxygen fuel (HVOF) spraying is the most recent development in the field of thermal spraying. The importance of this technique for the repair and new part manufacturing of jet engine parts is rapidly increasing. The HVOF uses a supersonic oxygen-fuel flame to heat and accelerate the powder particles that form the coating. The high particle velocity results in a high density and a low porosity, a high bond strength, and a high macro and micro hardness of the coating. The high quality of the HVOF coatings makes it possible to use these coatings on high loaded, rotating parts in jet engines. This paper will highlight the use of HVOF processes to apply erosion resistant cermet coatings to high pressure compressor blades. These blades are exposed to severe erosion. Next to the D-gun process, HVOF spraying is the only nonproprietary technique that can be used to apply these high performance coatings. Also the use of the HVOF process to apply wear resistant coatings and superalloys to jet engine parts will be discussed. The difference between HVOF coatings and plasma sprayed coatings will be highlighted. During HVOF spraying, the parts are exposed to a high heat flow. Solutions to avoid overheating, especially of titanium parts, will be presented.

A T J Verbeek↗

A Preliminary Study of the Preparation of Slurry Fuels from Vaporized Magnesium

Slurry fuels containing extremely small particles of magnesium were prepared by concentrating the dilute slurry product resulting from the shock-cooling of magnesium metal vapors with a liquid hydrocarbon spray. A complete description of the equipment and procedure used in preparing the fuel is given. Ninety-five percent by weight of the solid particles formed by this process passed through a 100-mesh screen. The particle-size distribution of the screened fraction of one run, as determined by sedimentation analysis, indicated that 73 percent by weight of the metal particles were finer than 2 microns in equivalent spherical diameter. The purity of the solid particles ranged as high as 98.9 percent by weight of free magnesium. The screened product was concentrated by means of a bowl-type centrifuge from 0.5 to more than 50 percent by weight solids content to form an extremely viscous, clay-like mass. By addition of a surface active agent, this viscous material was converted into a pumpable slurry fuel.

FUELS, PREPARATION↗

Sulfur and Moisture Effects on Alumina Scale and TBC Spallation

It has been well established that a few ppmw sulfur impurity may segregate to the interface of thermally grown alumina scales and the underlying substrate, resulting in bond degradation and premature spallation. This has been shown for NiAl and NiCrAl-based alloys, bare single crystal superalloys, or coated superalloys. The role of reactive elements (especially Y) has been to getter the sulfur in the bulk and preclude interfacial segregation. Pt additions are also very beneficial, however a similar thermodynamic explanation does not apply. The purpose of the present discussion is to highlight some observations of these effects on Rene'142, Rene'N5, PWA1480, and PWA1484. For PWA1480, we have mapped cyclic oxidation and spallation in terms of potential sulfur interfacial layers and found that a cumulative amount of about one monolayer is sufficient to degrade long term adhesion. Depending on substrate thickness, optimum performance occurs if sulfur is reduced below about 0.2-0.5 ppmw. This is accomplished in the laboratory by hydrogen annealing or commercially by melt-fluxing. Excellent 1150 C cyclic oxidation is thus demonstrated for desulfurized Rene'142, Rene'N5, and PWA1484. Alternatively, a series of N5 alloys provided by GE-AE have shown that as little as 15 ppmw of Y dopant was effective in providing remarkable scale adhesion. In support of a Y-S gettering mechanism, hydrogen annealing was unable to desulfurize these alloys from their initial level of 5 ppmw S. This impurity and critical doping level corresponds closely to YS or Y2S3 stoichiometry. In many cases, Y-doped alloys or alloys with marginal sulfur levels exhibit an oxidative sensitivity to the ambient humidity called Moisture-Induced Delayed Spallation (MIDS). After substantial scale growth, coupled with damage from repeated cycling, cold samples may spall after a period of time, breathing on them, or immersing them in water. While stress corrosion arguments may apply, we propose that the underlying cause is related to a hydrogen embrittlement reaction: Al alloy + 3 H2O = Al(OH)3 + 3H(+) + 3e(-). This mechanism is derived from an analogous moisture-induced hydrogen embrittlement mechanism originally shown for Ni3Al and FeAl intermetallics. Consequently, a cathodic hydrogen charging technique was used to demonstrate that electrolytic de-scaling occurs for these otherwise adherent alumina scales formed on Y-doped Rene'N5, in support of hydrogen effects. Finally, some TBC observations are discussed in light of all of the above. Plasma sprayed 8YSZ coatings, produced on PWA1484 without a bond coat, were found to survive more than 1000 1-hr cycles at 1100 C when desulfurized to below 0.1 ppmw. At higher sulfur (1.2 ppmw) levels, moisture sensitivity and delayed TBC failure, referred to as Desk Top Spallation, occurred at just 200 hr. Despite a large degree of scatter, a factor of 5 in life improvement is indicated for desulfurized samples in cyclic furnace tests, confirming the beneficial effect of low sulfur alloys on model TBC systems. (DTS and moisture effects are also observed on commercially applied PVD 7YSZ coatings on Rene'N5+Y with Pt-aluminide bond coats). These types of catastrophic failure were subverted on the model system by segmenting the substrate into a network of 0.010 high ribs, spaced in. apart, prior to plasma spraying. No failures occurred after 1000 cycles at 1150 C or after 2000 cycles at 1100 C, even after water immersion. The benefit is described in terms of elasticity models and a critical buckling stress.

Smialek, James L.↗

Fabrication, Analysis of Microstructure and Oxidation Resistance of Cemented C/C Composites by Laser

Cylindrical carbon–carbon composites have been cemented using a CO{sub 2} laser actuated by a raster scanning mirror system in a four-step sequence. Complete and homogenous surface cementation as well as thermal stability of the composites was sought after and achieved. The line of heat created from the laser beam impinged parallel to the axis of the pre-coated cylinder, while suspended from one end and slowly rotated. Four slurry compositions, all containing chloride salts from refractory elements, some combined with silicon, were pre-deposited by air spraying it over each specimen and then laser treated sequentially. Confined heat sublimed the chlorine ions resulting in silicide compounds that reacted with the carbon substrate to form a bonding layer. Microstructure characterization was performed using scanning electron microscopy, energy-dispersive spectroscopy and x-ray diffraction, immediately after the cementation was consolidated and after heat treated under argon. Preliminary oxidation weight loss tests were performed up to 1423 K under argon and air, revealing a 9.8 and 30.6% weight reduction, respectively, after 9 h of exposure. Cemented specimens were then coated with a glass overcoat layer that allowed them to perform moderately better against oxidation achieving up to a 28% weight loss after 20 h at 1273 K in air.

36 MATERIALS SCIENCE↗

A spiraled niobium tin superconductive ribbon

Copper film is vapor-deposited on clean ribbon and sprayed with photosensitive etch-resistant material. Photographic film masks are placed on ribbon and exposed to ultraviolet light. Etchant removes copper and exposure to oxidizing atmosphere forms niobium oxide. Photosensitive material is removed and ribbon is immersed in molten temperatures.

Coles, W. D.↗

Thin films by metal-organic precursor plasma spray

While most plasma spray routes to coatings utilize solids as the precursor feedstock, metal-organic precursor plasma spray (MOPPS) is an area that the authors have investigated recently as a novel route to thin film materials. Very thin films are possible via MOPPS and the technology offers the possibility of forming graded structures by metering the liquid feed. The current work employs metal-organic compounds that are liquids at standard temperature-pressure conditions. In addition, these complexes contain chemical functionality that allows straightforward thermolytic transformation to targeted phases of interest. Toward that end, aluminum 3,5-heptanedionate (Al(hd){sub 3}), triethylsilane (HSi(C{sub 2}H{sub 5}){sub 3} or HSiEt{sub 3}), and titanium tetrakisdiethylamide (Ti(N(C{sub 2}H{sub 5}){sub 2}){sub 4} or Ti(NEt{sub 2}){sub 4}) were employed as precursors to aluminum oxide, silicon carbide, and titanium nitride, respectively. In all instances, the liquids contain metal-heteroatom bonds envisioned to provide atomic concentrations of the appropriate reagents at the film growth surface, thus promoting phase formation (e.g., Si-C bond in triethylsilane, Ti-N bond in titanium amide, etc.). Films were deposited using a Sulzer Metco TriplexPro-200 plasma spray system under various experimental conditions using design of experiment principles. Film compositions were analyzed by glazing incidence x-ray diffraction and elemental determination by x-ray spectroscopy. MOPPS films from HSiEt{sub 3} showed the formation of SiC phase but Al(hd){sub 3}-derived films were amorphous. The Ti(NEt{sub 2}){sub 4} precursor gave MOPPS films that appear to consist of nanosized splats of TiOCN with spheres of TiO{sub 2} anatase. While all films in this study suffered from poor adhesion, it is anticipated that the use of heated substrates will aid in the formation of dense, adherent films.

36 MATERIALS SCIENCE↗

Assessment of Cold Spraying Mild-Steel Powder onto Mild-Steel Substrate for Development of Waste Tank Repair System - 20515

Infrastructure for nuclear waste storage and processing (e.g., waste tanks, transfer pipelines, evaporators) at the U.S. Department of Energy (DOE) Hanford Site has been in service well beyond its original design life. Past corrosion control methods at Hanford for waste tanks have not been fully successful, as evidenced by leaks forming in tank AY-102, the first double-shell tank (DST) constructed, and significant degradation detected in the primary tanks of AP-102 and AY-101. Failure of infrastructure components can pose a significant risk to the environment, worker safety, and project schedules. Therefore, remotely deployable methods for repairing and extending the service life of the existing tank waste infrastructure are needed. Cold spray has been identified as a potential technique for performing in situ repairs and material buildup for life extension of waste storage and processing infrastructure. Cold-spray repair methods and technology are well-established and are used extensively by industry and the military for making repairs using dissimilar materials. Pacific Northwest National Laboratory is evaluating the process of making repairs using mild-steel powder applied to a mild-steel substrate to minimize the galvanic corrosion potential. This paper presents the initial results for a feasibility ('go/no-go') assessment as to whether low-density deposits with sound metallurgic bonds, to build-back steel plate material, can be achieved using existing commercial cold-spray equipment. An assessment of steel-on-steel deposit is necessary to determine if cold spray is a viable candidate for DST carbon steel plate restoration/repair and thus DST service life extension. Powder properties and preparation requirements have been investigated and operating conditions and parameters for depositing a cold-spray buildup of mild steel on a mild-steel substrate have been determined. Soundness of metallurgic bonding as a function of the operating parameters exercised and results from applying cold spray to lay a deposit over simulated small-diameter flaws in 1/2-inch mild-steel plate are presented. Application of in situ cold-spray repair to the DOE complex has the potential to reduce cost and schedule impacts associated with component failures and the need to procure and construct replacement infrastructure. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Aqueous spray-drying synthesis of alluaudite Na 2+2x Fe 2–x (SO 4 ) 3 sodium insertion material: studies of electrochemical activity, thermodynamic stability, and humidity-induced phase transition

In pursuit of high-energy density sodium insertion materials, polyanionic frameworks can be designed with tuneable high-voltage operation stemming from inductive effect. Alluaudite Na 2 Fe 2 (SO 4 ) 3 polysulfate forms one such earth-abundant compound registering the highest Fe 3+ /Fe 2+ redox potential (ca. 3.8 V vs. Na/Na + ). While this SO 4 -based system exhibits high voltage operation, it is prone to thermal decomposition and moisture attack leading to hydrated derivatives, making its synthesis cumbersome. Also, the Na–Fe–S–O quaternary system is rich with (anhydrous to hydrated) phase transitions. Herein, we demonstrate scalable aqueous-based spray drying synthesis of alluaudite Na 2+2x Fe 2–x (SO 4 ) 3 sodium insertion material involving the formation of bloedite Na 2 Fe(SO 4 ) 2 ·4H 2 O as an intermediate phase. Moreover, a reversible phase transition from alluaudite to bloedite under controlled conditions of temperature and relative humidity is reported for the first time. Thermochemistry measurements revealed the enthalpies of formation (ΔH° f ) of alluaudite and bloedite are exothermic. Hydrated bloedite (ΔH° f = –117.16 ± 1.10 kJ/mol) was found to be significantly more energetically stable than anhydrous alluaudite (ΔH° f = –11.76 ± 1.25 kJ/mol). The calorimetric data support the observed synthesis and transformation (hydration-dehydration) pathways. Spray drying route led to spherical morphology delivering capacity ~80 mAh/g. Spray drying can be extended for rapid economic synthesis of sulfate class of battery materials.

25 ENERGY STORAGE↗

Seaborgite, LiNa6K2(UO2)(SO4)5(SO3OH)(H2O), the First Uranyl Mineral Containing Lithium

Abstract Seaborgite (IMA2019-087), LiNa6K2(UO2)(SO4)5(SO3OH)(H2O), is a new mineral species from the Blue Lizard mine, Red Canyon, San Juan County, Utah, U.S.A. It is a secondary phase found on gypsum in association with copiapite, ferrinatrite, ivsite, metavoltine, and römerite. Seaborgite occurs in sprays of light-yellow, long flattened prisms or blades, up to about 0.2 mm in length. Crystals are elongated on [100], flattened on {010}, and exhibit the forms {100}, {010}, {001}, and {101}. The mineral is transparent with vitreous luster and very pale-yellow streak. It exhibits bright lime-green fluorescence under a 405 nm laser. The Mohs hardness is ~2½. The mineral has brittle tenacity, curved or conchoidal fracture, and one good cleavage on {100}. The measured density is 2.97(2) g/cm3. The mineral is immediately soluble in H2O at room temperature. The mineral is optically biaxial (–), α = 1.505(2), β = 1.522(2), γ = 1.536(2) (white light); 2Vmeas = 85(1)°; moderate r < ν dispersion; orientation X ^ a ≈ 10°; pleochroic X colorless, Y and Z light green-yellow; X < Y ≈ Z. EPMA and LA-ICP-MS analyses of seaborgite undermeasured its Li, K, and Na. The empirical formula using Li, Na, and K based on the structure refinement is Li1.00Na5.81K2.19(UO2)(SO4)5(SO3OH)(H2O). Seaborgite is triclinic, P1, a = 5.4511(4), b = 14.4870(12), c = 15.8735(15) Å, α = 76.295(5), β = 81.439(6), γ = 85.511(6)°, V = 1203.07(18) Å3, and Z = 2. The structure (R1 = 0.0377 for 1935 I = 2σI) contains [(UO2)2(SO4)8]4– uranyl-sulfate clusters that are linked into a band by bridging LiO4 tetrahedra. The bands are linked through peripheral SO4 tetrahedra forming a thick heteropolyhedral layer. Channels within the layers contain a K site, while an additional K site, six Na sites, and an SO3OH group occupy the space between the heteropolyhedral layers.

Geochemistry & Geophysics↗

Analysis of Flame Deflector Spray Nozzles in Rocket Engine Test Stands

The development of a unified tightly coupled multi-phase computational framework is described for the analysis and design of cooling spray nozzle configurations on the flame deflector in rocket engine test stands. An Eulerian formulation is used to model the disperse phase and is coupled to the gas-phase equations through momentum and heat transfer as well as phase change. The phase change formulation is modeled according to a modified form of the Hertz-Knudsen equation. Various simple test cases are presented to verify the validity of the numerical framework. The ability of the methodology to accurately predict the temperature load on the flame deflector is demonstrated though application to an actual sub-scale test facility. The CFD simulation was able to reproduce the result of the test-firing, showing that the spray nozzle configuration provided insufficient amount of cooling.

Sachdev, Jai S.↗

Large Eddy Simulation and Analysis of Truck Generated Droplet Spray Transport at Bridges

Weathering steel is a particular type of steel that develops a higher level of atmospheric corrosion protection than non-weathering grades of steel. While uncoated weathering steels have the appearance of being “rusted”, there are many forms of ferric oxyhydroxides (aka. rust) that can form on steel. The predominant ferric oxyhydroxide that gives uncoated weathering steel its tightly adherent patina is goethite. The atmospheric corrosion protection comes from alloying, primarily with a copper composition greater than 0.20 percent and also small amounts of chrome, nickel, and silicon. Bare atmospheric corrosion resistant steels have been recognized as far back as 1905 with very early editions of the American Society for Testing and Materials (ASTM) A 7 “Standard Specification for Steel for Bridges and Buildings” [1]. Uncoated weathering steel (UWS) is the lowest cost corrosion protection system possible for a steel bridge based on the first cost. Provided the UWS is used in an optimal environment that allows the protective patina to form, UWS also provides the lowest life cycle cost. The protective patina on UWS does not form or degrades in continuously damp conditions, forming a higher proportion of lepidocrocite, or in the presence of a concentration of chlorine ions that is too high, forming a higher proportion of akageneite.

36 MATERIALS SCIENCE↗

Tank Tests of a Model of a Flying-boat Hull Having a Longitudinally Concave Planing Bottom

The NACA model 11-B, which has a longitudinally concave planing bottom forward of the step, was tested over a wide range of loading. The results of the tests are presented as curves of resistance and trimming moment plotted against speed for various trim angles and as curves of resistance coefficient at best trim angle, and trimming-moment coefficient. The characteristics of the form at the optimum trim are compared with those of NACA model 11-C which has the same form with the exception of a planing bottom longitudinally straight near the step. Photographs of the models being towed in the tank are included for a comparison of the spray patterns. At the best angles of trim in each case model 11-B has lower resistance at high speeds, a higher maximum positive trimming moment near the hump speed, and a more favorable spray pattern than of model 11-C.

Parkinson, J B↗

Marshall Convergent Coating Development Team: An Aerospace Success Story

The external thermal insulation systems for the Space Shuttle solid rocket boosters and the Air Force Titan IV payload fairings were in jeopardy due to EPA regulatory problems, endangering the flight status of both vehicles. The Marshall Convergent Coating (MCC-1) Development Team was formed in February 1994 to develop and implement an EPA-compliant external thermal insulation system for both systems. MCC-1 made use of a process known as Convergent Spray Technology (CST), a solventless, sprayable process that eliminated the environmentally hazardous chemicals involved with the old methods. Implemented in record time, the new insulation was so successful that it was selected for two additional flight vehicles, Boeing's Sea Launch and Delta TV. The activity also led to commercial spin-off pilot projects. The team continues today to share data between the various production sites, resolve production issues, expand the material's use, and consider potential improvements for the future.

Lester, Carl N.↗

Unique Facilities, Innovative Treatment Processes, and a Talented Workforce Allow Fluor Idaho to Successfully Disposition Transuranic Waste - 18388

Fluor Idaho is utilizing state-of-the-art equipment, treatment technologies, and employee expertise at the Department of Energy's (DOE) Idaho Site to treat contact-handled transuranic (CH-TRU) waste, as well as extremely challenging remote-handled transuranic (RH-TRU) waste forms, to prepare the material for shipment and permanent disposal at the Department's Waste Isolation Pilot Plant (WIPP). Nowhere else in the DOE Complex - perhaps the world - will one find the compilation of tools and an experienced workforce with an unparalleled history of safely retrieving, characterizing, treating, repackaging, certifying, and shipping TRU waste. Since 2003, the Advanced Mixed Waste Treatment Project (AMWTP) has used both conventional and unique retrieval concepts, high-tech characterization equipment - including real-time radiography and radioassay - robotics, and automated treatment processes to retrieve and treat 65,000 cubic meters of above-ground CH-TRU waste. Additionally, engineered controls and specialized personal protective equipment have allowed employees to make thousands of entries into high-radiation areas without a skin or clothing contamination incident - evidence of the employees' commitment to safety. AMWTP has encountered and found solutions for many challenging waste forms, including polychlorinated biphenyl-contaminated wastes, TRU waste containers with up to 1,000 fissile gram equivalent plutonium-239, oversized TRU boxes, and partially absorbed organic sludge waste. By utilizing additional facilities and equipment at the Accelerated Retrieval Project V and VII, Fluor Idaho has developed new processing lines and capabilities to ensure worker safety and milestone completion. These two soft-sided buildings, located at a facility adjacent to AMWTP, were originally constructed to exhume Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) TRU wastes from a section of a 97-acre landfill. After a total of 1,150 cubic meters of targeted waste were removed, personnel, working in collaboration with state regulators, successfully implemented a unique regulatory strategy that allowed these CERCLA facilities to be modified and permitted to treat Resource Conservation and Recovery Act (RCRA) wastes from the AMWTP - a savings of tens of millions of dollars over the cost of constructing new buildings. Adding to the AMWTP's technological uniqueness is its ability to treat wastes from other facilities in the DOE Complex. Two prior decision documents and an agreement with the state of Idaho have allowed AMWTP to treat wastes from 15 other DOE sites. It is the only project in the complex to have done so. At another project located next to AMWTP, targeted waste exhumation within the Subsurface Disposal Area is approximately two years ahead of schedule. Crews have removed more than 8,600 cubic meters of CH-TRU and hazardous wastes from eight exhumation areas that equal a combined footprint of 4.75 acres. Less than one acre remains to be exhumed to satisfy the 2008 Record of Decision waste exhumation end state between the DOE, Environmental Protection Agency, and state of Idaho. Construction of the final building where targeted waste exhumation will continue was completed during the summer of 2017. Exhumation will be completed within the next few years. Following exhumation completion, an evapotranspiration barrier (or cap) will be constructed over the entire landfill. Fluor Idaho continues to make progress on a more challenging project involving an inventory of RH-TRU waste that also contains the reactive metal sodium. Crews are utilizing hot cells, once used for spent nuclear fuel reprocessing and high-level waste treatment at the Idaho Nuclear Technology and Engineering Center, to render this challenging waste form safe for disposal in a national geologic waste repository. The treatment methods being employed on this RH-TRU waste are unique in the DOE Complex. Minute concentrations of water are sprayed onto the sodium-contaminated material in a process called 'spritzing' to chemically change the sodium from a reactive metal to a non-reactive salt. In other cases, sodium-contaminated waste is dipped in water to initiate a reaction in a process called 'immersion.' Lastly, for more challenging waste shapes that could not be successfully treated with the two prior methods, crews lower the sodium-contaminated RH-TRU waste into a one-of-a-kind distillation unit that uses high temperature and vacuum to volatilize the sodium and recapture it in a condenser unit for disposal. The RH-TRU waste treated with this technology is then safe for permanent disposal. Fluor Idaho is proud to operate DOE's CH- and RH-TRU waste treatment facilities, as well as use innovative processes and its talented workforce to complete this important work-scope. Such capabilities allow the contractor to meet the commitments made by the DOE to the state of Idaho. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Stable electrospray signal on a microfabricated glass chip with three-dimensional open edge and tiered depth geometries

This paper presents the microfabrication and performance of a three-dimensional electrospray ionization (ESI) emitter tip made from glass, which achieves stable current signals important for chemical analysis. Our novel microfabrication process and custom-built signal conditioning hardware provides the advantage of providing accurate features and steady signals. The fabrication process relies on standard microfabrication techniques (i.e., deposition, photolithography, and wet etching). This fabrication method involves the novel application of two layers of positive and negative photoresists in addition to Parafilm® wax tape. Open edge and tiered depth details were successfully created from a multilayer planar mask. This is a benefit for integrated miniaturized and microfluidic systems that often require micro features for their functionality but relatively large millimeter size features for their physical periphery. We demonstrate the fundamental performance of electrospray with this microfluidic chip. The emitter tip was fixed on a linear axis stage with high resolution (10 μm) to finely control the tip distance from a metal counter electrode plate. Further, a custom printed circuit board system was built to safely control four voltages applied to the microchip ports from a single high voltage power supply. To readily form the electrospray, non-aqueous solvents were used for their low viscosity and a constant voltage of +2.7 kV was applied to the sheath electrospray microchannel. The liquid being sprayed was 80/20 (v/v) methanol/acetonitrile with 0.1% acetic acid in the sheath microchannel and with ammonium acetate (10–40 mM) in its remaining microchannels. The electrospray signal was measured in response to varying the distance (1.4 to 1.6mm) between the electrospray emitter tip and a metal counter electrode plate in addition to the varying concentration of the background electrolyte, ammonium acetate. Stable and repeatable electrospray signal showed linear relationships with emitter tip distance and concentration (r 2 ≥ 0.95).

42 ENGINEERING↗

Porous Polymeric Materials FY24 PDRD Final Report

Fillers and pore formers are used in many materials at Kansas City National Security Campus (KCNSC) to fine tune density and stiffness. Current off-the-shelf options such as urea and Expancel do not always provide the desired properties. This project investigated several methods for introducing porosity in rigid polymers such as epoxy and polyurethane. This work was done at partnering universities to identify a variety of methods to create porous polymeric materials. The University of Oklahoma (OU) investigated emulsion templating of epoxy, where the epoxy is mixed with a surfactant and water to form an emulsion. The emulsion is then molded and cured. During the cure process, water droplets evaporate to form porous structures. Total porosity can be tuned by changing the concentration of water added to the polymer. The University of Kansas (KU) investigated the synthesis of phenolic microballoons by spray drying, as well as methods of incorporating removable porogens into epoxy and polyurethane materials to create polymeric foams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cryogenic insulation strength and bond tester

A method and apparatus for testing the tensile strength and bonding strength of sprayed-on foam insulation attached to metal cryogenic fuel tanks is described. A circular cutter is used to cut the insulation down to the surface of the metal tank to form plugs of the insulation for testing in situ on the tank. The apparatus comprises an electromechanical pulling device powered by a belt battery pack. The pulling device comprises a motor driving a mechanical pulling structure comprising a horizontal shaft connected to two bell cracks which are connected to a central member. When the lower end of member is attached to a fitting, which in turn is bonded to a plug, a pulling force is exerted on the plug sufficient to rupture it. The force necessary to rupture the plug or pull it loose is displayed as a digital read-out.

Schuerer, P. H.↗