Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Elucidating the Role of Electric Fields in Fe Oxidation via an Environmental Atom Probe

We quantify the effects of intensely applied electric fields on the Fe oxidation mechanism. The specimen are pristine Fe single crystals exposing a variety of surface structures identified by field ion microscopy. These crystals are simultaneously exposed to low pressures of pure oxygen gas, on the order of 10 −7 mbar, while applying intense electric fields on their surface of several tens of volts per nanometer. The local composition of the different surface structures is probed directly and in real time using an Environmental Atom Probe and successfully compared with first principles-based models. We found that rough Fe{244} and Fe{112} facets are more reactive toward oxygen than compact Fe{024} and Fe{011} facets. Results demonstrate that the influence of an electric field on the oxidation kinetics depends on the timescales that are involved as the system evolves toward equilibrium. The initial oxidation kinetics show that strong increases in electric fields facilitate the formation of an oxide. However, as one approaches equilibrium, high field values mitigate this formation. Ultimately, this study elucidates how high externally applied electric fields can be used to dynamically exploit reaction dynamics at the nanoscale towards desired products in a catalytic reaction at mild reaction conditions.

09 BIOMASS FUELS↗
DOE OSTI2020

Basic Research of Intrinsic Tamper indication Markings and Patterns defined by Pulsed Laser Irradiation

With our previous research, it was found that surface asperities or roughness must be present to create periodic surface structures upon laser exposure. In particular, an initial rough surface morphology (such as that found with a machined surface) provides multiple sites for light scattering, which underlies the formation of periodic ripple morphologies. Light scattering from a random surface creates patterns of periodic structures (with complex orientations) that could be used as intrinsic markings for tagging materials and equipment. Despite these initial findings, the fundamental mechanisms that give rise to periodic surface structures and their characteristic shapes were not identified in prior research.

36 MATERIALS SCIENCE↗
DOE OSTI2020

O 2 -Oxidation of Individual Graphite and Graphene Nanoparticles in the 1200 – 2200 K Range: Particle-to-Particle Variations and the Evolution of the Reaction Rates and Optical Properties

The kinetics for O 2 oxidation of individual graphite and graphene platelet nanoparticles (NPs) were studied as a function of temperature (1200 to 2200 K) at varying oxygen partial pressures, using a single nanoparticle mass spectrometry method. NP temperature (TNP) was measured by measuring the NP thermal emission spectra during the kinetics studies. The initial oxidation efficiency is found to peak in the 1200 to 1500 K range, dropping by an order of magnitude as TNP was increased above 2000 K. There were large NP-to-NP variations in the oxidation rates, attributed to variations in the NP surface structure. In addition, the oxidation efficiencies evolved, non-monotonically, as the NPs reacted, decreasing by factors of between 10 and 300. This evolution of reactivity is attributed to changes in the NP surface structure due to the combination of oxidation and annealing. In conclusion, the optical properties, including wavelength dependence of the emissivity and the absorption cross section for the 532 nm heating laser, also tended to evolve as the NPs oxidized, but differently for each individual NP, presumably reflecting differences in the initial structures and their evolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

DROPWISE CONDENSATION ON MICRO- AND NANOSTRUCTURED SURFACES

In this review we cover recent developments in the area of surface-enhanced dropwise condensation against the background of earlier work. The development of fabrication techniques to create surface structures at the micro-and nanoscale using both bottom-up and top-down approaches has led to increased study of complex interfacial phenomena. In the heat transfer community, researchers have been extensively exploring the use of advanced surface structuring techniques to enhance phase-change heat transfer processes. In particular, the field of vapor-to-liquid condensation and especially that of water condensation has experienced a renaissance due to the promise of further optimizing this process at the micro-and nanoscale by exploiting advances in surface engineering developed over the last several decades.

Enright, R↗
NASA NTRS1984

Development of laminar flow control wing surface porous structure

It was concluded that the chordwise air collection method, which actually combines chordwise and spanwise air collection, is the best of the designs conceived up to this time for full chord laminar flow control (LFC). Its shallower ducting improved structural efficiency of the main wing box resulting in a reduction in wing weight, and it provided continuous support of the chordwise panel joints, better matching of suction and clearing airflow requirements, and simplified duct to suction source minifolding. Laminar flow control on both the upper and lower surfaces was previously reduced to LFC suction on the upper surface only, back to 85 percent chord. The study concludes that, in addition to reduced wing area and other practical advantages, this system would be lighter because of the increase in effective structural wing thickness.

Klotzsche, M.↗
DOE OSTI2023

Correlating Rate-Dependent Transition Metal Dissolution between Structure Degradation in Li-Rich Layered Oxides

Understanding the mechanism of the rate-dependent electrochemical performance degradation in cathodes is crucial to developing fast charging/discharging cathodes for Li-ion batteries. Here, in this work, taking Li-rich layered oxide Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 as the model cathode, the mechanisms of performance degradation at low and high rates are comparatively investigated from two aspects, the transition metal (TM) dissolution and the structure change. Quantitative analyses combining spatial-resolved synchrotron X-ray fluorescence (XRF) imaging, synchrotron X–ray diffraction (XRD) and transmission electron microscopy (TEM) techniques reveal that low-rate cycling leads to gradient TM dissolution and severe bulk structure degradation within the individual secondary particles, and especially the latter causes lots of microcracks within secondary particles, and becomes the main reason for the fast capacity and voltage decay. In contrast, high-rate cycling leads to more TM dissolution than low-rate cycling, which concentrates at the particle surface and directly induces the more severe surface structure degradation to the electrochemically inactive rock-salt phase, eventually causing a faster capacity and voltage decay than low-rate cycling. These findings highlight the protection of the surface structure for developing fast charging/discharging cathodes for Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2016

A LASER INTERFERENCE-BASED SURFACE TREATMENT OF AL AND CARBON FIBER POLYMER COMPOSITES FOR ENHANCED BONDING

Due to its increased use in the automotive and aerospace industries, joining of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) to metals demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using a new laser based technique, in which the laser interference power profile was created by splitting the beam and guiding those beams to the sample surface by overlapping each other with defined angles to each other. Results were presented for the overlap shear testing of single-lap joints made with Al 5182 and CFPC specimens whose surfaces prepared by (a) surface abrasion and solvent cleaning; and (b) laser-interference structured surfaces by rastering with a 4 mm laser beam at approximately 3.5 W power. CFPC specimens of T700S carbon fiber, Prepreg T70 epoxy, 4 or 5 ply thick, 0/90o plaques were used. Adhesive DP810 was used to bond Al and CFPC. The bondline was 0.25mm and the bond length was consistent among all joints produced. First, the effect of the laser speed on the joint performance was evaluated by laser-interference structure Al and CFPC surfaces with a beam angle of 3o and laser beam speeds of 3, 5, and 10 mm/s. For this sensitivity study, 3 joint specimens were used per each joint type. Based on the results for minimum, maximum, and mean values for the shear lap strength and maximum load for all the 9 joint types, two joint types were selected for further evaluations. Six additional joint specimens were prepared for these two joint types in order to obtain better statistics and the shear test data was presented for the range, mean, and standard deviation. The results for the single-lap shear tests obtained for six joint specimens, indicate that the shear lap strength, maximum load, and displacement at maximum load for those joints made with laser-interference structured surfaces were increased by approximately 14.8%, 16%, and 100%, respectively over those measured for the baseline joints.

Sabau, Adrian S↗
DOE OSTI2020

Consequences of long-term water exposure for bulk crystal structure and surface composition/chemistry of nickel-rich layered oxide materials for Li-ion batteries

Water exposure of layered nickel-rich transition metal oxide electrodes, widely used in high-energy lithium-ion batteries, has detrimental effects on the electrochemical performance, which complicates electrode handling and prevents implementation of environmentally benign aqueous processing procedures. Elucidating the degradation mechanisms in play may help rationally mitigate/circumvent key challenges. Here, the bulk structural consequences of long-term (>2.5 years) deuterated water (D2O) exposure of intercalation materials with compositions Li x Ni 0.5 Co 0.2 Mn 0.3 O 2 (NCM523) and Li x Ni 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) are studied by neutron powder diffraction (NPD). Detailed inspection of the NPD data reveals gradual formation of a secondary crystalline phase in all exposed samples, not previously reported for this system. This unknown phase forms faster in liquid- compared to vapor-exposed compounds. Structural modelling of the NPD data shows a stable level of Li/Ni anti-site defects and does not indicate any significant changes in lattice parameters or hydrogen-lithium (D + /Li + ) exchange in the structure. Consequently, the secondary phase formation must take place via transformation rather than modification of the parent material. X-ray photoelectron spectroscopy data indicate formation of LiHCO 3 /Li 2 CO 3 at the surface and a Li-deficient oxide in the sub-surface region of the pristine compounds, and the presence of adsorbed water and transition metal hydroxides at the exposed sample surfaces.

25 ENERGY STORAGE↗
DOE OSTI2025

Preliminary modeling of triply periodic minimal surface (TPMS) structures using RELAP5-3D

With the United States Department of Energy (DOE)’s goal of quadrupling the nation’s nuclear energy supply by 2050, and with the Advanced Fuels Campaign pushing for new types of advanced reactor fuels and geometries, the need has arisen for new nuclear fuel designs. One such design is to swap out current nuclear fuel geometries in exchange for another type of geometry, called a Triply Periodic Minimal Surface (TPMS). TPMSs are self-supporting, infinitely repeating lattices—attributes that lend themselves well to additive manufacturing. These surfaces also possess enhanced heat transfer properties thanks to their internal area changes and large surface-area-to-volume ratios. Their drawback, however, is an increased pressure drop. Given the small amount of correlations and data (Reynolds numbers in the 2,000–8,000 range), and the minimal amount of experience so far obtained by modeling TPMS structures using 1D systems codes such as the Reactor Excursion and Leak Analysis Program (RELAP5-3D), further research into this topic was needed. Using data from the University of Wisconsin - Madison (UW), curve fits were created for both a Heat Transfer Coefficient (HTC) correlation and a Darcy friction factor empirical coefficient correlation. The curves’ coefficients and multipliers were then output and utilized in RELAP5-3D models of two upcoming experiments—Flow Loop for INFLUX Pressure drop (FLIP) and Microreactor Agile Non-nuclear Experimental Test (MAGNET)—aimed at increasing the available data for Reynolds numbers to the 16,000–36,000 range for TPMS structures. The models were run under the conditions utilized by a Computational Fluid Dynamics (CFD) analysis performed by another group at Idaho National Laboratory. Only CFD pressure drop values were obtained from the FLIP test, and those values showed that the RELAP5-3D models had a lower rate of pressure increase in comparison to the CFD values. In addition, there seemed to be a vertical shift upward in the pressure drop for both models whenever the TPMS porosity decreased, and the RELAP5-3D models showed a higher vertical shift in comparison to the CFD values. The MAGNET results did not correspond to any CFD or experimental results against which they could be compared, so they were instead compared against the proposed CFD input conditions. These values were then compared with each other to make sure the model seemed to be performing as expected, paving the way for future tests that can be run for the purpose of further analyses and comparisons. The pressure drop increased with temperature and mass flow rate independently. The temperature change would decrease with increasing mass flow rate and temperature, which was just as we expected based on the fact that the lower viscosity and decreased density would result in higher friction and churning losses. The last metric that was assessed was the enthalpy flow change, which increased with increasing mass flow rate and decreasing temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Effect of film thickness on structural and mechanical properties of AlCrN nanocompoite thin films deposited by reactive DC magnetron sputtering

In this study, the influence of film thickness on the structural, surface morphology and mechanical properties of Aluminum chromium nitride (AlCrN) thin films has been successfully investigated. The AlCrN thin films were deposited on silicon (100) substrate using dc magnetron reactive co-sputtering at substrate temperature 400° C. The structural, surface morphology and mechanical properties were studied using X-ray diffraction, field-emission scanning electron microscopy and nanoindentation techniques respectively. The thickness of these thin films was controlled by varying the deposition time therefore increase in deposition time led to increase in film thickness. X-ray diffraction pattern of AlCrN thin films with different deposition time shows the presence of (100) and (200) orientations. The crystallite size varies in the range from 12.5 nm to 36.3 nm with the film thickness due to surface energy minimization with the higher film thickness. The hardness pattern of these AlCrN thin films follows Hall-Petch relation. The highest hardness 23.08 Gpa and young modulus 215.31 Gpa were achieved at lowest grain size of 12.5 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS2020

Asymmetric Surface Brightness Structure of Caustic Crossing Arc in SDSS J1226+2152: A Case for Dark Matter Substructure

We study the highly magnified arc SGAS J122651.3+215220 caused by a star-forming galaxy at z s = 2.93 crossing the lensing caustic cast by the galaxy cluster SDSS J1226+2152 (z l = 0.43), using Hubble Space Telescope observations. We report in the arc several asymmetric surface brightness features whose angular separations are a fraction of an arcsecond from the lensing critical curve and appear to be highly but unequally magnified image pairs of underlying compact sources, with one brightest pair having clear asymmetry consistently across four filters. One explanation of unequal magnification is microlensing by intracluster stars, which induces independent flux variations in the images of individual or groups of source stars in the lensed galaxy. For a second possibility, intracluster dark matter subhaloes invisible to telescopes effectively perturb lensing magnifications near the critical curve and give rise to persistently unequal image pairs. Our modelling suggests, at least for the most prominent identified image pair, that the microlensing hypothesis is in tension with the absence of notable asymmetry variation over a six-year baseline, while subhaloes of ∼10 6 –10 8 \Mꙩ anticipated from structure formation with cold dark matter typically produce stationary and sizable asymmetries. We judge that observations at additional times and more precise lens models are necessary to stringently constrain temporal variability and robustly distinguish between the two explanations. The arc under this study is a scheduled target of a Director’s Discretionary Early Release Science program of the James Webb Space Telescope, which will provide deep images and a high-resolution view with integral field spectroscopy.

Liang Dai↗
DOE OSTI2019

A quantitative study of the structure-activity relationship in hierarchical zeolites using liquid-phase reactions

Micro/meso/macroporous (hierarchical) zeolites show remarkable catalytic performance for reactions involving bulky reactants. However, quantitative assessment of the microstructural characteristics contributing to the observed performance remains elusive. Here, structure–activity relationships are established for a set of micro/mesoporous self-pillared pentasil (SPP) zeolites using two parallel liquid-phase reactions (benzyl alcohol alkylation and self-etherification) based on analysis of mass transport and reaction kinetics. A reaction–diffusion mathematical model is developed that quantitatively assigns the catalytic contributions of the external surface and micropores of SPP zeolites for these reactions. In addition, the effect of the zeolite external surface structure on the corresponding catalytic activity is quantitatively assessed by comparing SPP zeolites (with MFI structure) with MCM-22 (with MWW structure). This work demonstrates that reaction–diffusion modeling allows quantitative description of the catalytic performance of hierarchical zeolites and provides a model reaction to assess nm-sized characteristic diffusion lengths in MFI.

bio-inspired↗
DOE OSTI2019

Steam reforming of simulated bio-oil on K-Ni-Cu-Mg-Ce-O/Al 2 O 3 : The effect of K

Steam reforming of simulated bio-oil (ethanol, acetone, phenol, and acetic acid) and phenol has been studied on K-Ni-Cu-Mg-Ce-O/Al 2 O 3 composite catalysts. Complementary characterization techniques, such as nitrogen sorption, XRD, H2-TPR, H2-TPD, CO-TPD, CO-DRIFTS, and in situ XPS, were used to correlate surface structure and functionality to catalytic performance of potassium (K) doped catalysts. K doping of the Ni-Cu-Mg-Ce-O/Al 2 O 3 catalyst created a Ni°/Ni 2+ mixed active phase, which not only enhanced steam reforming activity, but also suppressed the methanation reaction. In addition, K doping changed the surface acid-basic properties of the catalyst, which instead favor the water-gas shift reaction. With the combination of these effects, K doping of Ni-Cu-Mg-Ce-O/Al 2 O 3 catalysts led to higher C1 yield and much lower methane formation, favoring hydrogen production in steam reforming of both phenol and simulated bio-oil.

Yu, Ning↗
DOE OSTI2023

Improving robustness for model discerning synthesis process of uranium oxide with unsupervised domain adaptation

The quantitative characterization of surface structures captured in scanning electron microscopy (SEM) images has proven to be effective for discerning provenance of an unknown nuclear material. Recently, many works have taken advantage of the powerful performance of convolutional neural networks (CNNs) to provide faster and more consistent characterization of surface structures. However, one inherent limitation of CNNs is their degradation in performance when encountering discrepancy between training and test datasets, which limits their use widely. The common discrepancy in an SEM image dataset occurs at low-level image information due to user-bias in selecting acquisition parameters and microscopes from different manufacturers. Therefore, in this study, we present a domain adaptation framework to improve robustness of CNNs against the discrepancy in low-level image information. Furthermore, our proposed approach makes use of only unlabeled test samples to adapt a pretrained model, which is more suitable for nuclear forensics application for which obtaining both training and test datasets simultaneously is a challenge due to data sensitivity. Through extensive experiments, we demonstrate that our proposed approach effectively improves the performance of a model by at least 18% when encountering domain discrepancy, and can be deployed in many CNN architectures.

scanning electron microscopy↗
NASA NTRS1980

Surface relief structures for multiple beam LO generation

Linear and binary holograms for use in heterodyne detection with 10.6 micron imaging arrays are described. The devices match the amplitude and phase of the local oscillator to the received signal and thus maximize the system signal to noise ratio and resolution and minimize heat generation on the focal plane. In both the linear and binary approaches, the holographic surface-relief pattern is coded to generate a set of local oscillator beams when the relief pattern is illuminated by a single planewave. Each beam of this set has the same amplitude shape distribution as, and is collinear with, each single element wavefront illuminating array.

Veldkamp, W. B.↗
NASA NTRS1972

Active seismic experiment

The Apollo 16 active seismic experiment (ASE) was designed to generate and monitor seismic waves for the study of the lunar near-surface structure. Several seismic energy sources are used: an astronaut-activated thumper device, a mortar package that contains rocket-launched grenades, and the impulse produced by the lunar module ascent. Analysis of some seismic signals recorded by the ASE has provided data concerning the near-surface structure at the Descartes landing site. Two compressional seismic velocities have so far been recognized in the seismic data. The deployment of the ASE is described, and the significant results obtained are discussed.

Kovach, R. L.↗
DOE OSTI2022

Regulation of Surface Defect Chemistry toward Stable Ni-Rich Cathodes

Surface reconstruction of Ni-rich layered oxides (NLO) degrades the cycling stability and safety of high-energy-density lithium-ion batteries (LIBs), which challenges typical surface-modification approaches to build a robust interface with electrochemical activity. Here, a strategy of leveraging the low-strain analogues of Li- and Mn-rich layered oxides (LMR) to reconstruct a stable surface on the Ni-rich layered cathodes is proposed. The new surface structure not only consists of a gradient chemical composition but also contains a defect-rich structure regarding the formation of oxygen vacancies and cationic ordering, which can simultaneously facilitate lithium diffusion and stabilize the crystal structure during the (de)lithiation. These features in the NLO lead to a dramatic improvement in electrochemical properties, especially the cyclability under high voltage cycling, exhibiting the 30% increase in capacity retention after 200 cycles at the current density of 1 C (3.0-4.6 V). We report the findings offer a facile and effective way to regulate defect chemistry and surface structure in parallel on Ni-rich layered structure cathodes to achieve high-energy density LIBs.

25 ENERGY STORAGE↗