SEARCH · Search NASA

Results for “Swept”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1985

The use of a panel code on high lift configurations of a swept forward wing

A study was done on high lift configurations of a generic swept forward wing using a panel code prediction method. A survey was done of existing codes available at Ames, frow which the program VSAERO was chosen. The results of VSAERO were compared with data obtained from the Ames 7- by 10-foot wind tunnel. The results of the comparison in lift were good (within 3.5%). The comparison of the pressure coefficients was also good. The pitching moment coefficients obtained by VSAERO were not in good agreement with experiment. VSAERO's ability to predict drag is questionable and cannot be counted on for accurate trends. Further studies were done on the effects of a leading edge glove, canards, leading edge sweeps and various wing twists on spanwise loading and trim lift with encouraging results. An unsuccessful attempt was made to model spanwise blowing and boundary layer control on the trailing edge flap. The potential results of VSAERO were compared with experimental data of flap deflections with boundary layer control to check the first order effects.

Scheib, J. S.↗

NASA NTRS1986

Multivariable control of a forward swept wing aircraft

The impact of independent canard and flaperon control of the longitudinal axis of a generic forward swept wing aircraft is examined. The Linear Quadratic Gaussian (LQG)/Loop Transfer Recovery (LTR) method is used to design three compensators: two single-input-single-output (SISO) systems, one with angle of attack as output and canard as control, the other with pitch attitude as output and canard as control, and a two-input-two-output system with both canard and flaperon controlling both the pitch attitude and angle of attack. The performances of the three systems are compared showing the addition of flaperon control allows the aircraft to perform in the precision control modes with very little loss of command following accuracy.

Quinn, W. W.↗

NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

A study has been conducted in the NASA-Langley Transonic Dynamics wind tunnel to determine the divergence characteristics of a high aspect ratio forward swept wing of rectangular planform, for sweep angles of zero, -15, -30, -45, and -60 deg. In addition to a rectangular wingtip, a tip whose geometry lay parallel with the freestream flow was tested at a sweep angle of -45 deg. The primary objective was to obtain data that could be used to verify the divergence prediction capabilities of an aeroelastic analysis code employing kernel function aerodynamics. The analytical predictions of convergence were found to be conservative for all forward sweep angles, and the effect of the two tip shapes on divergence dynamic pressure were accurately predicted.

Cole, S. R.↗

NASA NTRS1986

Effects of wind-tunnel noise on swept-cylinder transition at Mach 3.5

Transition data are reported for circular cylinders at swept angles of 45 and 60 degrees in the Mach 3.5 pilot-low-disturbance tunnel where free-stream noise levels are varied from approximately .05-0.5 percent in terms of the rms fluctuating pressure normalized by the mean static pressure. Results indicate that end plate or boundary layer trip disturbances at the upstream end of the cylinders cause turbulent flow along the entire test Reynolds number range of 10-170 thousand per inch. With all end plate and trip disturbances removed, transition at the attachment lines occurred at free-stream Reynolds numbers based on diameters of about 70-80 thousand, independent of stream noise levels. The installation of small trips on the attachement lines caused transition at lower Reynolds numbers, depending on both the roughness height and the wind tunnel noise level.

Creel, T. R., Jr.↗

NASA NTRS1986

Noise generated by convected gusts interacting with swept airfoil cascades

An analysis is developed for the noise generated by the interaction of a rotor viscous wake with a cascade of swept stator vanes. The stator vanes span a channel formed by infinite parallel walls and containing a subsonic mean flow. High frequency interactions, for which the noise generation is concentrated at the vane leading edge, are considered. The analysis utilizes a superposition of the solution to the isolated stator vane problem, presented in an earlier paper, to develop an approximate solution to the cascade problem. The rotor wake model includes the features of wake circumferential lean and a linear spanwise variation of the magnitude of the wake deficit velocity. Calculations are presented which show that, for rotor wakes with moderate circumferential lean, stator sweep produces substantial reductions in noise level. The vane sweep must be oriented to enhance the phase lags along the vane leading edge produced by wake lean. The noise levels are found to be fairly insensitive to spanwise variations in the wake deficit.

Envia, E.↗

NASA NTRS1985

Research in lightning swept-stroke attachment patterns and flight conditions with the NASA F-106B airplane

Data on 637 direct lightning strikes and 117 close flashes observed by the NASA instrumented F-106B aircraft as part of the Storm Hazards Program at NASA Langley during 1980-1984 are compiled and analyzed, updating the report of Fisher and Plumer (1983). The airborne and ground-based measurement and recording apparatus and the flight and data-reduction procedures are described, and the results are discussed in terms of lightning-strike-conducive flight conditions and lightning attachment patterns. A peak strike rate of 2.1/min is found at altitude 38,000-40,000 ft and temperature below -40 C, with very few strikes below 20,000 ft. Four categories of swept-flash attachment pattern are identified, but it is pointed out that all exterior surfaces of the F-106B are potential attachment sites.

Fisher, B. D.↗

NASA NTRS1986

Flowfield survey over a 75 deg swept delta wing at an angle of attack of 20.5 deg

An experimental investigation of the flowfield over a 75 deg swept delta wing at an angle of attack of 20.5 deg has been conducted. The data include pitot pressure surveys and two types of flow visualization. Surface and flowfield visualization data were obtained at Reynolds number, Rn, ranging from 0.5 to 2.0 million in increments of 0.25 million. Detailed pitot pressure surveys were made at five longitudinal stations at Rn = 0.5, 1.0, and 1.5 million in both the primary and secondary vortices. The results indicate that Reynolds number has only a minor effect on the global structure of the flowfield in the Reynolds number range that was investigated. The boundary layer transitions from laminar to turbulent at the trailing edge of the wing at Rn = 1.0 x 10 to the 6th, and the transition moves forward to x/L = 0.4 at Rn = 2.0 x 10 to the 6th. The positions of the primary vortex cores are insensitive to Reynolds number in this range; however, the lateral position of the secondary vortex core moves outboard aft of the region where the boundary layer transitions from laminar to turbulent.

Kjelgaard, S. O.↗

NASA NTRS1987

Flight Research on a Forward-Swept-Wing Airplane

Tests yield information relating to design, safety, and performance. Report gives overview of flight research program on X-29A experimental airplane. X-29A features forward-swept wings. Research program providing data needed to improve design, fabrications, and testing procedures for airplane.

Sefic, Walter J.↗

NASA NTRS1986

Swept frequency technique for dispersion measurement of microstrip lines

Microstrip lines used in microwave integrated circuits are dispersive. Because a microstrip line is an open structure, the dispersion can not be derived with pure TEM, TE, or TM mode analysis. Dispersion analysis has commonly been done using a spectral domain approach, and dispersion measurement has been made with high Q microstrip ring resonators. Since the dispersion of a microstrip line is fully characterized by the frequency dependent phase velocity of the line, dispersion measurement of microstrip lines requires the measurement of the line wavelength as a function of frequency. In this paper, a swept frequency technique for dispersion measurement is described. The measurement was made using an automatic network analyzer with the microstrip line terminated in a short circuit. Experimental data for two microstrip lines on 10 and 30 mil Cuflon substrates were recorded over a frequency range of 2 to 20 GHz. Agreement with theoretical results computed by the spectral domain approach is good. Possible sources of error for the discrepancy are discussed.

Lee, R. Q.↗

NASA NTRS1987

Applicability of linearized-theory attached-flow methods to design and analysis of flap systems at low speeds for thin swept wings with sharp leading edges

Low-speed experimental force and data on a series of thin swept wings with sharp leading edges and leading and trailing-edge flaps are compared with predictions made using a linearized-theory method which includes estimates of vortex forces. These comparisons were made to assess the effectiveness of linearized-theory methods for use in the design and analysis of flap systems in subsonic flow. Results demonstrate that linearized-theory, attached-flow methods (with approximate representation of vortex forces) can form the basis of a rational system for flap design and analysis. Even attached-flow methods that do not take vortex forces into account can be used for the selection of optimized flap-system geometry, but design-point performance levels tend to be underestimated unless vortex forces are included. Illustrative examples of the use of these methods in the design of efficient low-speed flap systems are included.

Carlson, Harry W.↗

NASA NTRS1987

Subsonic longitudinal and lateral-directional characteristics of a forward-swept-wing fighter configuration at angles of attack up to 47 deg

Subsonic lateral-direction and longitudinal characteristics of a forward-swept-wing fighter configuration were examined in wind-tunnel tests at Mach numbers of 0.2 and 0.5 for angles of attack from -7 to 47 deg. and over a sidelslip range of +/- 15 deg. The effects of a canard, strakes, vertical tail, and leading- and trailing-edge flaps are examined. The canard and strakes both reduce asymmetric moments and side forces at zero sideslip for angles of attack up to about 30 deg. The canard has a small influence on lateral-directional stability; however, strakes produce a substantial reduction in lateral stability for angles of attack greater than about 20 deg. The vertical tail improves directional stability for angles of attack up to 30 deg. Deflection of the leading-edge flap to 20 deg. at high angles of attack on the strake and canard configurations degrades lateral and directional stability. Deflection of the trailing-edge flap to 20 deg. on the canard configuration generally increases lateral and directional stability at high angles of attack. Leading- and trailing-edge flaps on the wing-body and canard configurations are effective for increased lift only for angles of attack up to about 40 deg. The leading-edge flap remains effective on the strake configuration over the entire angle-of-attack range tested.

Mann, Michael J.↗

NASA NTRS1987

Swept frequency technique for dispersion measurement of microstrip lines

Lee, Richard Q.↗

NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind-tunnel measurements of boundary-layer and wake velocity profiles and surface static-pressure distributions are presented for a swept, circulation-control wing. The model is an aspect-ratio-four semispan wing mounted on the tunnel side wall at a sweep angle of 45 deg. A full-span, tangential, rearward-blowing, circulation-control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary-layer profiles measured on the forward portions of the wing are approximately streamwise and two-dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three-dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near-wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5-deg angle of attack, a range of jet blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower-surface separation location with blowing rate was determined from boundary-layer measurements at Mach 0.425.

Spaid, Frank W.↗

NASA NTRS1987

Supersonic turbulent flow past a 3-D swept compression corner at Mach 3

Experimental and theoretical studies are presented on the three-dimensional shock wave-turbulent boundary layer interaction generated by a swept compression corner at Mach 3 for compression angle of 24 deg, sweep angle of 60 deg, and Reynolds numbers from 140,000 to 900,000. Two theoretical approaches were used, both of which utilize the full mass-averaged compressible three-dimensional Navier-Stokes equations but differ in the choice of turbulence model (the Baldwin-Lomax, 1978, and the Jones-Launder, 1972, model, respectively). The features of the computed mean flow structure were found to be qualitatively the same for both the Baldwin-Lomax and Jones-Launder models.

Knight, Doyle D.↗

NASA NTRS1986

Design and experimental evaluation of a swept supercritical Laminar Flow Control (LFC) airfoil

A large chord swept supercritical laminar flow control (LFC) airfoil was designed, constructed, and tested in the NASA Langley 8-ft Transonic Pressure Tunnel (TPT). The LFC airfoil experiment was established to provide basic information concerning the design and compatibility of high-performance supercritical airfoils with suction boundary layer control achieved through discrete fine slots or porous surface concepts. It was aimed at validating prediction techniques and establishing a technology base for future transport designs and drag reduction. Good agreement was obtained between measured and theoretically designed shockless pressure distributions. Suction laminarization was maintained over an extensive supercritical zone up to high Reynolds numbers before transition gradually moved forward. Full-chord laminar flow was maintained on the upper and lower surfaces at M sub infinity = 0.82 up to R sub c is less than or equal to 12 x 10 to the 6th power. When accounting for both the suction and wake drag, the total drag could be reducted by at least one-half of that for an equivalent turbulent airfoil. Specific objectives for the LFC experiment are given.

Harvey, W. D.↗

NASA NTRS1987

Pressure distributions and oil-flow patterns for a swept circulation-control wing

Pressure distributions and photographs of oil flow patterns are presented for a circulation control wing. The model was an aspect ratio four semispan wing mounted on the side wall of the NASA Ames Transonic Wind Tunnel. The airfoil was a 20 percent thick ellipse, modified with circular leading and trailing edges of 4 percent radius, and had a 25.4 cm constant chord. This configuration does not represent a specific wing design, but is generic. A full span, tangetial, rearward blowing, circulation control slot was incorporated ahead of the trailing edge on the upper surface. The wing was tested at Mach numbers from 0.3 to 0.75 at sweep angle of 0 to 45 deg with internal to external pressure ratios of 1.0 to 3.0. Lift and pitching momemt coefficients were obtained from measured pressure distributions at five span stations. When the conventional corrections resulting from sweep angle are applied to the lift and moment of circulation control sections, no additional corrections are necessary to account for changes in blowing efficiency. This is demonstrated for an aft sweep angle of 45 deg. An empirical technique for estimating the downwash distribution of a swept wing was validated.

Keener, Earl R.↗

NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind tunnel measurements of boundary layer and wake velocity profiles and surface static pressure distributions are presented for a swept, circulation control wing. The model is an aspect ratio four semispan wing mounted on the tunnel side wall as a sweep angle of 45 deg. A full span, tangetial, rearward blowing, circulation control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary layer profiles measured on the forward portions of the wing are approximately streamwise and two dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5 deg angle of attack, a range of jet blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower surface separation location with blowing rate was determined from the boundary layer measurements at Mach 0.425.

Spaid, Frank W.↗

NASA NTRS1988

Development of Disturbances in Swept Wing Flows

The development of a subharmonic secondary instability in a boundary layer with pressure gradients controlled by suction was investigated. The effect of suction control on this early stage leading to transition is evaluated. The secondary three-dimensional instability problem for compressible boundary layers was formulated to investigate theoretically the effect of finite amplitude two-dimensional wave on the growth of three-dimensional perturbations in compressible boundary layers. Only a range of Mach numbers up to the transonic, where the critical primary disturbance is two dimensional, was covered. Thr evolution of resonant triads in three-dimensional boundary layers was investigated. The triads investigated were comprised of different modes, stationary crossflow (CF), traveling crossflow, vertical vorticity (VV), and Tollmein-Schlichting (TS) modes. The mean flow used in the calculations is the boundary layer on a modern LFC transonic 23 swept wing. In the analysis the growth of the boundary layer is taken into account assuming that it is of the same order as the nonlinear effects.

Kandil, Osama A.↗