Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEMPERATURE PROFILE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Solar occultation sounding of pressure and temperature using narrowband radiometers

A technique for simultaneously retrieving pressure and temperature profiles using satellite-based narrowband radiometer measurements of absorption in the CO2 4.3-micron band is described. Pressure and temperature profiles for earth's upper atmosphere on a global scale can be obtained with errors less than 3% and 3 K, respectively. The p-T information can be used not only for improving the accuracy of inverted gas concentrations in the same absorption experiment but also for investigating the upper atmosphere circulation.

Park, J. H.↗
NASA NTRS1994

(abstract) Tropospheric Calibration for the Mars Observer Gravity Wave Experiment

In spring 1993, microwave radiometer-based tropospheric calibration was provided for the Mars Observer gravitational wave search. The Doppler shifted X-band radio signals propagating between Earth and the Mars Observer satellite were precisely measured to determine path length variations that might signal passage of gravitational waves. Experimental sensitivity was restricted by competing sources of variability in signal transit time. Principally, fluctuations in the solar wind and ionospheric plasma density combined with fluctions in tropospheric refractivity determined the detection limit. Troposphere-induced path delay fluctions are dominated by refractive changes caused by water vapor inhomogeneities blowing through the signal path. Since passive microwave remote sensing techniques are able to determine atmospheric propagation delays, radiometer-based tropospheric calibration was provided at the Deep Space Network Uranus tracking site (DSS-15). Two microwave water vapor radiometers (WVRs), a microwave temperature profiler (MTP), and a ground based meterological station were deployed to determine line-of-sight vapor content and vertical temperature profile concurrently with Mars Observer tracking measurements. This calibration system provided the capability to correct Mars Observer Doppler data for troposphere-induced path variations. We present preliminary analysis of the Doppler and WVR data sets illustrating the utility of WVRs to calibrate Doppler data. This takes an important step toward realizing the ambitious system required to support future Ka-band Cassini satellite gravity wave tropospheric calibration system.

atmospheric water vapor microwave remote sensing↗
NASA NTRS2009

Data Assimilation Experiments Using Quality Controlled AIRS Version 5 Temperature Soundings

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing and reprocessing of all AIRS data. The AIRS Science Team Version 5 retrieval algorithm contains a number of significant improvements over Version 4. Two very significant improvements are described briefly below. 1) The AIRS Science Team Radiative Transfer Algorithm (RTA) has now been upgraded to accurately account for effects of non-local thermodynamic equilibrium on the AIRS observations. This allows for use of AIRS observations in the entire 4.3 micron CO2 absorption band in the retrieval algorithm during both day and night. Following theoretical considerations, the,AIRS Version 5 temperature profile retrieval step uses only 15 micron CO2 radiances for those channels sensitive to atmospheric emission in the stratosphere. Tropospheric temperature profile information is obtained almost exclusively from clear column radiances in the 4.3 micron CO2 band. These clear column radiances are a derived product that are indicative of radiances AIRS channels would have seen if the field of view were completely clear. Tropospheric sounding 15 micron CO2 observations are used heavily in the determination of the parameters necessary to generate for all sounding channels. This approach allows for the generation of accurate values of and T(p) under most cloud conditions.

Susskind, Joel↗
NASA NTRS1994

Thermal analysis of a functionally graded material subject to a thermal gradient using the boundary element method

The boundary element method is utilized in this study to conduct thermal analysis of functionally graded composites, materials in which the internal microstructure or properties are explicitly tailored in order to obtain an optimal response, on the micromechanical (constituent) scale. A unique feature of the boundary element formulations used here is the use of circular shape functions to convert the two-dimensional integrations of the composite fibers to one dimensional integrations. Using the computer code BEST-CMS, the through the thickness temperature profiles are computed for a representative material with varying numbers of fibers and fiber spacing in the thickness direction. The computed temperature profiles are compared to those obtained using an alternate analytical theory which explicitly couples the heterogeneous microstructure to the global analysis. The boundary element results compared favorably to the analytical calculations, with discrepancies that are explainable based on the boundary element formulation. The results serve both to demonstrate the ability of the boundary element method to analyze these types of materials, and to verify the accuracy of the analytical theory.

Goldberg, Robert K.↗
NASA NTRS1990

Description of SAFIRE for ISES

The SAFIRE (Spectroscopy of the Atmosphere using Far Infrared Emission) is a limb emission experiment using a far-IR Fourier transform spectrometer (FTS) and a mid-IR broadband multispectral radiometer covering the range 80 to 1600/cm. The purpose of this experiment is to obtain vertical distributions of temperature and key constituents of O(y), HO(y), NO(y), ClO(y), and BrO(y) families in the stratosphere, mesosphere, and thermosphere. The spectral channels and gases within each channel are summarized. The instrument includes a 48 element (6 x 8) Ge:GA detector array operating at 4 K in the far-IR and a 105 element (7 x 15) HgCdTe array operating at 80 K in the mid-IR. The SAFIRE uses four different scan modes for vertical coverage and resolution to address various scientific requirements. The SAFIRE data reduction will start with the retrieval of temperature profile as a function of pressure using two CO2 channel data. Constituent distributions then are obtained from other channel data using the retrieved temperature profile. The SAFIRE measurements are limited to the region above the tropopause because of radiance saturation by H2O and clouds. The computational capability necessary to process at the instrument data rate is estimated to be 19 MFLOPS for FTS data and 0.02 MFLOPS for radiometer data. It seems, therefore, that the real-time applications of SAFIRE data using an onboard processing device is not feasible. Although a temperature anomaly may be detected from the two CO2 radiometer channels using an onboard processor for the stratosphere, it is not possible to distinguish between CO2 outflux and temperature anomaly. Temperature anomaly does not, therefore, offer tropospheric information useful for real-time application.

Park, Jae H.↗
NASA NTRS2008

Data Assimilation Experiments using Quality Controlled AIRS Version 5 Temperature Soundings

The AIRS Science Team Version 5 retrieval algorithm has been finalized and is now operational at the Goddard DAAC in the processing (and reprocessing) of all AlRS data. Version 5 contains accurate case-by-case error estimates for most derived products, which are also used for quality control. We have conducted forecast impact experiments assimilating AlRS quality controlled temperature profiles using the NASA GEOS-5 data assimilation system, consisting of the NCEP GSI analysis coupled with the NASA FVGCM. Assimilation of quality controlled temperature profiles resulted in significantly improved forecast skill in both the Northern Hemisphere and Southern Hemisphere Extra-Tropics, compared to that obtained from analyses obtained when all data used operationally by NCEP except for AlRS data is assimilated. Experiments using different Quality Control thresholds for assimilation of AlRS temperature retrievals showed that a medium quality control threshold performed better than a tighter threshold, which provided better overall sounding accuracy; or a looser threshold, which provided better spatial coverage of accepted soundings. We are conducting more experiments to further optimize this balance of spatial coverage and sounding accuracy from the data assimilation perspective. In all cases, temperature soundings were assimilated well below cloud level in partially cloudy cases. The positive impact of assimilating AlRS derived atmospheric temperatures all but vanished when only AIRS stratospheric temperatures were assimilated. Forecast skill resulting from assimilation of AlRS radiances uncontaminated by clouds, instead of AlRS temperature soundings, was only slightly better than that resulting from assimilation of only stratospheric AlRS temperatures. This reduction in forecast skill is most likely the result of significant loss of tropospheric information when only AIRS radiances unaffected by clouds are used in the data assimilation process.

Susskind, Joel↗
NASA NTRS1987

A numerical simulation to verify the stress-free growth of silicon crystal ribbon

Thermal stresses developed during the growth of silicon crystal ribbon have been shown to be negligible, thus eliminating residual stresses and dislocations, if the temperature profile satisfies a second-order partial differential equation inside the ribbon. This has been numerically verified through a finite element model, an outline of which is presented here. This model shows that, for homogeneous isotropic material with temperature independent thermal expansion coefficients, thermal stresses will vanish if the temperature profile satisfies the Laplacian. A comparison of stresses due to uniform and nonuniform temperature gradients in the plane of the ribbon is also presented. The strategies employed to control the round-off error and to validate the computer model are discussed.

Ray, Sujit K.↗
NASA NTRS1981

Clear air turbulence studies with microwave radiometers

The flight testing of two passive microwave radiometers for the detection of clear air turbulence (CAT) is discussed. A 55.3 GHz radiometer was used to measure altitude temperature profiles, and a 180 GHz radiometer was used for monitoring line-of-sight integrated water vapor content. The sequence of altitude temperature profiles, spaced 17 seconds apart (3.5 km), enable inversion layer and tropopause properties to be studied. On some occasions, the altitude distribution of CAT severity correlated well with inversion layer location. On other occasions, turbulence was not located within 55.3 GHz measured layers, possibly indicating cases of topography-generated CAT, where inversion layer would not necessarily be expected. Evidence was obtained supporting the hypothesis that CAT is generated within layers containing levels of wind shear that cannot be supported by the layer's lapse rate; i.e., that Kelvin-Helmholtz wave breakdown can generate CAT. The 180 GHz radiometer failed to warn of CAT events. It is suggested that the radiometer's sensitivity (1 K) was inadequate for detecting the small variations in line-of-sight water vapor content.

Gary, B. L.↗
NASA NTRS2000

Karst Groundwater Hydrologic Analyses Based on Aerial Thermography

On February 23, 1999, thermal imagery of Marshall Space Flight Center, Alabama was collected using an airborne thermal camera. Ground resolution was I in. Approximately 40 km 2 of thermal imagery in and around Marshall Space Flight Center (MSFC) was analyzed to determine the location of springs for groundwater monitoring. Subsequently, forty-five springs were located ranging in flow from a few ml/sec to approximately 280 liter/sec. Groundwater temperatures are usually near the mean annual surface air temperature. On thermography collected during the winter, springs show up as very warm spots. Many of the new springs were submerged in lakes, streams, or swamps; consequently, flow measurements were difficult. Without estimates of discharge, the impacts of contaminated discharge on surface streams would be difficult to evaluate. An approach to obtaining an estimate was developed using the Environmental Protection Agency (EPA) Cornell Mixing Zone Expert System (CORMIX). The thermography was queried to obtain a temperature profile down the center of the surface plume. The spring discharge was modeled with CORMIX, and the flow adjusted until the surface temperature profile was matched. The presence of volatile compounds in some of the new springs also allowed MSFC to unravel the natural system of solution cavities of the karst aquifer. Sampling results also showed that two springs on either side of a large creek had the same water source so that groundwater was able to pass beneath the creek.

Campbell, C. Warren↗
NASA NTRS1994

Reanalysis of X-ray emission from M87. 1: The single-phase medium

We reanalyze the density and temperature profiles of the X-ray-emitting gas around M87, assuming a spherically symmetric, single-phase model. For given assumed density and temperature profiles, we predict Einstein High Resolution Imager (HRI) and Imaging Proportional Counter (IPC) surface brightness distribution as well as Focal Point Crystal Spectrometer (FPCS) line fluxes, which we compare with the data. We find that a good fit to these data can be obtained and that, with a suitable adjustment of the abundances, the equivalent width of the iron complex at 7 keV as observed by wide-beam instruments can also be explained. In contrast to this, the Einstein Solid State Spectrometer (SSS) spectrum and optically determined mass profiles cannot be accounted for simultaneously with the previous X-ray data. We show that the disagreement of the Solid State Spectrometer with our models is due to an inconsistency of the Solid State Spectrometer data with that of the other X-ray instruments. Because of this, we find no evidence for the existence of absorption above the Galactic value, contrary to an earlier claim based on Solid State Spectrometer data. The disagreement of our models with optical mass data is due either to the assumption of a single-phase model, thus rendering the model unacceptable, or possibly to maximal systematic errors in the FPCS data. We also show that thermal conduction at the Spitzer rate is important in our models, although this conclusion is of limited importance in view of the poor fit of our models to the data.

Tsai, John C.↗
NASA NTRS1995

Average power effects in parametric oscillators and amplifiers

Average power effects relative to the operation of parametric oscillators and amplifiers have been calculated. Temperature gradients have been calculated for both radial and longitudinal heat extraction. In many instances, the thermal load on a parametric oscillator is higher than the thermal load on a parametric amplifier with the same pump power. Having one or both these wavelengths resonant increases the chances that a generated photon will be absorbed by the nonlinear crystal. Temperature profiles and thermal diffusion time constants have been calculated for Gaussian beams, given the heat-deposition rate. With radical heat extraction the temperature profile can be expressed in a power series or approximated by a Gaussian distribution function.

Barnes, Norman P.↗
NASA NTRS2006

Thermal Dispersion Within a Porous Medium Near a Solid Wall

The regenerator is a key component to Stirling cycle machine efficiency. Typical regenerators are of sintered fine wires or layers of fine-wire screens. Such porous materials are contained within solid-waH casings. Thermal energy exchange between the regenerator and the casing is important to cycle performance for the matrix and casing would not have the same axial temperature profile in an actual machine. Exchange from one to the other may allow shunting of thermal energy, reducing cycle efficiency. In this paper, temperature profiles within the near-wall region of the matrix are measured and thermal energy transport, termed thermal dispersion, is inferred. The data show how the wall affects thermal transport. Transport normal to the mean flow direction is by conduction within the solid and fluid and by advective transport within the matrix. In the near-wall region, both may be interrupted from their normal in-core pattern. Solid conduction paths are broken and scales of advective transport are damped. An equation is presented which describes this change for a wire screen mesh. The near-wall layer typically acts as an insulating layer. This should be considered in design or analysis. Effective thermal conductivity within the core is uniform. In-core transverse thermal effective conductivity values are compared to direct and indirect measurements reported elsewhere and to 3D numerical simulation results, computed previously and reported elsewhere. The 3-D CFD model is composed of six cylinders in cross flow, staggered in arrangement to match the dimensions and porosity of the matrix used in the experiments. The commercial code FLUENT is used to obtain the flow and thermal fields. The thermal dispersion and effective thermal conductivities for the matrix are computed from the results.

Simon, T.↗
NASA NTRS2022

New Constraints on Titan's Stratospheric n-Butane Abundance

Curiously, n-butane has yet to be detected at Titan, though it is predicted to be present in a wide range of abundances that span over 2.5 orders of magnitude. We have searched infrared spectroscopic observations of Titan for signals from n-butane (n-C4H10) in Titan's stratosphere. Three sets of Cassini Composite Infrared Spectrometer Focal Plane 4 (1050–1500 cm−1) observations were selected for modeling, having been collected from different flybys and pointing latitudes. We modeled the observations with the Nonlinear Optimal Estimator for MultivariatE Spectral AnalySIS radiative transfer tool. Temperature profiles were retrieved for each of the data sets by modeling the ν4 emission from methane near 1305 cm−1. Then, incorporating the temperature profiles, we retrieved abundances of all of Titan's known trace gases that are active in this spectral region, reliably reproducing the observations. We then systematically tested a set of models with varying abundances of n-butane, investigating how the addition of this gas affected the fits. We did this for several different photochemically predicted abundance profiles from the literature, as well as for a constant-with-altitude profile. Ultimately, though we did not produce any firm detection of n-butane, we derived new upper limits on its abundance specific to the use of each profile and to multiple different ranges of stratospheric altitudes. These results will tightly constrain the C4 chemistry of future photochemical modeling of Titan's atmosphere and also motivate the continued search for n-butane and its isomer, isobutane.

Brendan L. Steffens↗
NASA NTRSDate not supplied

Atmospheric Structure Investigation Instrument: in-Situ Measurement of Vertical Profiles of Temperature, Pressure, Wind, Aerosol Density, Hydrogen Ortho/Para Fraction and Helium Abundance on Saturn or Uranus.

The Atmospheric Structure Investigation (ASI) is designed as a threshold sensor suite for descent probes into any planetary atmosphere, principally for the Giant planets (e.g., Saturn for New Frontiers, or Uranus for an upcoming Flagship identified in the decadal survey), but also could be relevant for Venus, Titan or even specific applications on Earth. Its aim is to supply the key measurements establishing the atmospheric structure upon which all the other probe measurements would be placed in context. To that end, it measures vertical profiles of probe acceleration and rotation[1,2], pressure, temperature, vertical winds, aerosol number density and size and scattering properties, as well as Hydrogen ortho/para fraction and Helium abundance.

V Jha↗
NASA NTRS2017

Status and Plans for Finalization of SRT's Contribution to AIRS Version-7 and Version-7 AO

Version-6.46 temperature profiles, water vapor profiles, and especially total O3, are very much compared to Version-6. With minor tweaking, Version-6.46 is a good candidate for use in Version-7. JPL Version-6.4.6 and Version-6.4.6 AO monthly mean products agree extremely well with each other. Version-6.4.6 AO is accurate enough that there is not necessarily a need to process both Version-7 and Version-7 AO data sets. Single day comparisons show Version-6.46 CrIS/ATMS and Version-6.46 AIRS/AMSU products agree extremely well with each other. We need to demonstrate agreement of Version-6.46 CrIS/ATMS and Version-6.46 AO products on a monthly mean basis for different months and years. CrIS/ATMS and AIRS/AMSU monthly mean comparisons showed excellent agreement using a previous version.

CrIS/ATMS↗
NASA NTRS2007

Improving Forecast Skill by Assimilation of Quality-controlled AIRS Temperature Retrievals under Partially Cloudy Conditions

The National Aeronautics and Space Administration (NASA) Atmospheric Infrared Sounder (AIRS) on board the Aqua satellite has been long recognized as an important contributor towards the improvement of weather forecasts. At this time only a small fraction of the total data produced by AIRS is being used by operational weather systems. In fact, in addition to effects of thinning and quality control, the only AIRS data assimilated are radiance observations of channels unaffected by clouds. Observations in mid-lower tropospheric sounding AIRS channels are assimilated primarily under completely clear-sky conditions, thus imposing a very severe limitation on the horizontal distribution of the AIRS-derived information. In this work it is shown that the ability to derive accurate temperature profiles from AIRS observations in partially cloud-contaminated areas can be utilized to further improve the impact of AIRS observations in a global model and forecasting system. The analyses produced by assimilating AIRS temperature profiles obtained under partial cloud cover result in a substantially colder representation of the northern hemisphere lower midtroposphere at higher latitudes. This temperature difference has a strong impact, through hydrostatic adjustment, in the midtropospheric geopotential heights, which causes a different representation of the polar vortex especially over northeastern Siberia and Alaska. The AIRS-induced anomaly propagates through the model's dynamics producing improved 5-day forecasts.

Reale, O.↗
NASA NTRS1989

A thermal analysis of a spirally wound battery using a simple mathematical model

A two-dimensional thermal model for spirally wound batteries has been developed. The governing equation of the model is the energy balance. Convective and insulated boundary conditions are used, and the equations are solved using a finite element code called TOPAZ2D. The finite element mesh is generated using a preprocessor to TOPAZ2D called MAZE. The model is used to estimate temperature profiles within a spirally wound D-size cell. The model is applied to the lithium/thionyl chloride cell because of the thermal management problems that this cell exhibits. Simplified one-dimensional models are presented that can be used to predict best and worst temperature profiles. The two-dimensional model is used to predict the regions of maximum temperature within the spirally wound cell. Normal discharge as well as thermal runaway conditions are investigated.

Evans, T. I.↗