Search NASA⌕ Search

SEARCH · Search NASA

Results for “Technology Utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

ITER Central Solenoid Alternate Pre-Compression Structure Concept and Analysis

The ITER Central Solenoid (CS) is comprised of six independent coils held together by a pre-compression support structure. This structure must provide enough preload to maintain sufficient coil-to-coil contact throughout the current pulse. End of burn (EOB) represents one extreme time-point when the currents in the CS3 coils oppose those of CS1 & CS2. The present baseline design uses nine tie plate pairs located on the coil ID and OD to achieve this pre-compression. While this is an efficient structural approach, the outer tie plates limit access to the coil OD and result in very tight tolerances over the 12.75 m tall toroidal field (TF) coil bore. An alternative pre-compression structure has been developed by the US ITER Project Office, which addresses both of these issues using only internal tension members. This allows clear access to the outer CS surface for plumbing and current feeders, and more reasonable OD tolerances. In addition, the Tension Rod pre-compression structure utilizes existing technology (such as hydraulic tensioner or Superbolt{reg_sign}), which streamlines initial preloading and subsequent adjustments. Structural and transient electromagnetic FEA of the tension rod concept demonstrates that the stresses, displacements, and preliminary Eddy current heat loads are within allowable limits. Fabrication estimates demonstrate no additional cost of the tension rods compared to the tie plates.

36 MATERIALS SCIENCE↗

ITER Central Solenoid support structure analysis

The ITER Central Solenoid (CS) is comprised of six independent coils held together by a pre-compression support structure. This structure must provide enough preload to maintain sufficient coil-to-coil contact and interface load throughout the current pulse. End of burn (EOB) represents one of the most extreme time-points doing the reference scenario when the currents in the CS3 coils oppose those of CS1 & CS2. The CS structure is performance limited by the room temperature static yield requirements needed to support the roughly 180 MN preload to resist coil separation during operation. This preload is applied by inner and external tie plates along the length of the coil stack by mechanical fastening methods utilizing Superbolt technology. The preloading structure satisfies the magnet structural design criteria of ITER and will be verified during mockup studies. The solenoid is supported from the bottom of the toroidal field (TF) coil casing in both the vertical radial directions. The upper support of the CS coil structure maintains radial registration with the TF coil in the event of vertical disruptions (VDE) loads and earthquakes. All of these structure systems are analyzed via a global finite element analysis (FEA). The model includes a complete sector of the TF coil and the CS coil/structure in one self-consistent analysis. The corresponding results and design descriptions are described in this report.

42 ENGINEERING↗

CRRES observations of ion composition during EMIC mode wave events

EMIC mode waves may play an important role in the dynamics of the growth and loss of the radiation belts. CRRES mission analysis has provided extensive information on the distributions of EMIC mode waves. Less well studied and understood is the role that ion composition plays in the formation of the EMIC mode waves. The CRESS plasma mass spectrometer LOMICS measured all ion species of interest up to 45 keV/q. This preliminary study will examine the characteristics of heavy ions during a multitude of wave events, in particular, the effect of ion composition on wave-particle interactions, amplitude, and frequency. The relevance of such data to the upcoming RBSP mission will be highlighted.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Expanding the potential for saline formations : modeling carbon dioxide storage, water extraction and treatment for power plant cooling.

The National Water, Energy and Carbon Sequestration simulation model (WECSsim) is being developed to address the question, 'Where in the current and future U.S. fossil fuel based electricity generation fleet are there opportunities to couple CO{sub 2} storage and extracted water use, and what are the economic and water demand-related impacts of these systems compared to traditional power systems?' The WECSsim collaborative team initially applied this framework to a test case region in the San Juan Basin, New Mexico. Recently, the model has been expanded to incorporate the lower 48 states of the U.S. Significant effort has been spent characterizing locations throughout the U.S. where CO{sub 2} might be stored in saline formations including substantial data collection and analysis efforts to supplement the incomplete brine data offered in the NatCarb database. WECSsim calculates costs associated with CO{sub 2} capture and storage (CCS) for the power plant to saline formation combinations including parasitic energy costs of CO{sub 2} capture, CO{sub 2} pipelines, water treatment options, and the net benefit of water treatment for power plant cooling. Currently, the model can identify the least-cost deep saline formation CO{sub 2} storage option for any current or proposed coal or natural gas-fired power plant in the lower 48 states. Initial results suggest that additional, cumulative water withdrawals resulting from national scale CCS may range from 676 million gallons per day (MGD) to 30,155 MGD depending on the makeup power and cooling technologies being utilized. These demands represent 0.20% to 8.7% of the U.S. total fresh water withdrawals in the year 2000, respectively. These regional and ultimately nation-wide, bottom-up scenarios coupling power plants and saline formations throughout the U.S. can be used to support state or national energy development plans and strategies.

01 COAL, LIGNITE, AND PEAT↗

FLUIDIC: Metal Air Recharged

Fluidic, with the help of ARPA-E funding, has developed and deployed the world's first proven high cycle life metal air battery. Metal air technology, often used in smaller scale devices like hearing aids, has the lowest cost per electron of any rechargeable battery storage in existence. Deploying these batteries for grid reliability is competitive with pumped hydro installations while having the advantages of a small footprint. Fluidic's battery technology allows utilities and other end users to store intermittent energy generated from solar and wind, as well as maintain reliable electrical delivery during power outages. The batteries are manufactured in the US and currently deployed to customers in emerging markets for cell tower reliability. As they continue to add customers, they've gained experience and real world data that will soon be leveraged for US grid reliability.

25 ENERGY STORAGE↗

Advanced Nuclear Technology: Advanced Light Water Reactors Utility Requirements Document Small Modular Reactors Inclusion Summary

This report summarizes a project by EPRI to include requirements for small modular light water reactors (smLWR) into the EPRI Utility Requirements Document (URD) for Advanced Light Water Reactors. The project was jointly funded by EPRI and the U.S. Department of Energy (DOE). The report covers the scope and content of the URD, the process used to revise the URD to include smLWR requirements, a summary of the major changes to the URD to include smLWR, and how to use the URD as revised to achieve value on new plant projects.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Stable, fertile, high polyhydroxyalkanoate producing plants and methods of producing them

Transgenic plants that produce high levels of polyhydroxybutyrate and methods of producing them are provided. In a preferred embodiment the transgenic plants are produced using plastid transformation technologies and utilize genes which are codon optimized. Stably transformed plants able to produce greater than 10% dwt PHS in tissues are also provided.

59 BASIC BIOLOGICAL SCIENCES↗

First Test Results of the bERLinPro 2-cell Booster Cavities

The bERLinPro Energy Recovery Linac (ERL) is currently being built at Helmholtz-Zentrum Berlin in order to study the physics of operating a high-current, a 100 mA, 50 MeV ERL utilizing all SRF cavity technology. This machine will utilize three unique SRF cryomodules for the photoinjector, booster and linac cryomodules respectively. The focus of this paper will be on the cavities contained within the booster cryomodule. Here there will be three 2-cell SRF cavities, based on the original design by Cornell University, but optimized to meet the needs of the project. All of the cavity fabrication, processing and testing was carried out at Jefferson Laboratory, where 4 cavities were produced, and the 3 cavities with the best RF performance were fitted with helium vessels for installation in the cryomodule. This paper will report on the test results of the cavities as measured in the vertical testing dewar at JLab after fabrication and again after outfitting with the helium vessels.

43 PARTICLE ACCELERATORS↗

A Cooperative Freeway Merge Assistance System Using Connected Vehicles

This paper describes a novel freeway merge assistance system utilizing V2X technology with the help of the DSRC protocol. The freeway merge assistance system uses an innovative three-way handshaking protocol and provides advisories to drivers to guide the merging sequence.

Ahmed, Md Salman↗

Subtask 1.4 - Techno-Economic Assessment of Regional Carbon Utilization Scenarios and Attendant Monitoring Technology

The U.S. Department of Energy (DOE) Carbon Storage Program seeks to develop technologies to significantly improve the effectiveness of carbon capture and storage (CCS), reduce the cost of implementation, and support the readiness of widespread commercial deployment by 2035. To accomplish this goal, technical and economic barriers must be addressed and the results used to inform regulators and industry on the safety, permanence, and viability of carbon storage. To help overcome these barriers, the Energy & Environmental Research Center (EERC) conducted three activities: 1) investigate the regional techno-economic life cycle of CO2 enhanced oil recovery (EOR) in North Dakota, 2) assist DOE in determining the prospective CO2 storage resource of residual oil zones (ROZs), and 3) develop a seismic technique for monitoring geologic storage of CO2. These three activities address two strategic goals enumerated in the DOE–EERC Cooperative Agreement, namely, 1) to advance foundational science and 2) to inform data-driven policies that enhance U.S. economic growth and job creation, energy security, and environmental quality. Activity 1 In North Dakota, there is synergistic incentive to develop and implement CO2 EOR technologies. Regional industry partners are actively seeking options that can cost-effectively improve the efficiency of power production, while also coproducing CO2 for use in EOR applications. A full-value-chain techno-economic assessment that links lignite resources, power generation, and EOR is needed to determine the implications for a state or region to continue to use these resources or look elsewhere for other energy sources and revenue streams. The integration of North Dakota’s lignite power industry with the state’s oil industry has the potential to revitalize legacy oil fields and produce up to 1 billion barrels of additional oil using CO2 EOR while providing a market for a CO2 commodity captured at coal-fired power plants. Revitalization of North Dakota’s legacy oil fields will bring new industry investment to the state, resulting in the growth of oil-related jobs and revenue through oil sales, severance tax, and associated oilfield development activities (drilling, pipelines, etc.). CO2 demand for EOR and incremental oil production were calculated for 201 conventional oil fields in North Dakota. Infrastructure development in the fields was estimated using 1) a traditional vertical well arrangement of CO2 injectors and oil producers and 2) an advanced case where horizontal wells were used exclusively. Pipeline, compression, and recycling infrastructure requirements were also estimated. When viewed from the CO2 capture and CO2 EOR sectors, the advanced case showed a positive investment scenario when including potential benefits of the 45Q tax credit policy. An economic evaluation of a full implementation of CO2 EOR showed an average $60 billion potential state economic impact estimated over the 37-year construction and production time frame could be realized with an assumed oil price of $65/bbl. Oil price ranges of $35–$90/bbl cause an estimated variation of ±$5 billion over the potential effort. The total net state government revenues were estimated over the 37-year construction and production time frame. With an assumed oil price of $65/bbl, total potential fiscal impact could average $7.4 billion. This result ranges about ±$2.5 billion for a potential EOR implementation effort for oil price ranges of $35–$90/bbl. This broad-brush assessment was focused on “magnitude-of-effect” perspectives of what CO2 capture and use for EOR could mean to the state. Whether CO2 EOR ever becomes widely adopted is not the issue at this stage of evaluation. The question being answered is, How valuable could CO2 capture and CO2 EOR be for the state and local jurisdictions in western North Dakota? The results of the current economic assessment remove any ambiguity to that question. Full implementation of CO2 EOR as modeled in this study provides substantial economic benefits to the state, even at low oil prices (i.e., $35/bbl). Job creation and government revenues could be substantial, depending on the scale of implementation. With a better understanding of what CO2 EOR might mean for the state’s economy, the focus can now shift to the policies and financial mechanisms needed to make private investment in CO2 capture and use as EOR competitive with other energy-related pursuits. Activity 2 ROZs contain remnants of oil not swept away by natural waterflooding. Although nearly all of the identified ROZs are found in West Texas, there is evidence that this category of oil reservoir can be found in other major oil-producing basins of the United States. Because the formation of these oil reservoirs is distinct from other conventional reservoirs, the method to estimate the prospective CO2 storage resource in ROZs may be equally distinct from the method used for conventional fields. As such, the EERC collaborated with DOE’s National Energy Technology Laboratory (NETL) to investigate the feasibility of CO2 storage in ROZs and determine what specific modification (if any) needs to be made to the current DOE volumetric method to estimate prospective CO2 storage resource in oil reservoirs. This activity built on a previous EERC investigation to identify ROZs in the Williston and Powder River Basins and upon collaborations between the EERC and NETL to develop storage resource estimation methods for different types of geologic CO2 storage. Review of the volumetric approach raised questions about the applicability of such an approach to hydrocarbon-bearing zones without the inclusion of potential hydrocarbon production. A production-based approach was presented by the EERC to inform the working group of additional methods of increasing the CO2 storage resource potential. Because the production-based method focuses more heavily on oil recovery than CO2 storage, it was not included in the working group manuscript. Activity 3 The EERC has used sparse and irregular seismic arrays to detect CO2 injected into a reservoir. The variability of seismic noise recorded by the sensors directly impacts the seismic interpretation. However, designing noise attenuation workflows effectively can be a more challenging task using sparse and irregular arrays for data acquisition. Based on the hypothesis that noncoherent noise is stationary during weekly data acquisition, a new machine-learning algorithm was developed to automatically estimate noise conditions using passive records, noise from active records, and ancillary information. The new noise attenuation processing workflow can improve the time-lapse detection of CO2 from sparse and irregular array acquisitions. Results show spatial and temporal noise patterns can be related to the location of the sensors and the weather conditions during the data acquisition and that our attenuation processing workflow can improve the time-lapse detection of CO2 from sparse and irregular array acquisitions. This effort was funded in part through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Department of Commerce.

Peck, Wesly↗

Application of MP-PIC on Dual Interconnected Chemical Looping Cold Flow System: Validation Process with Hydrodynamic Experiments

Chemical looping with oxygen uncoupling (CLOU) is a promising carbon capture technologies, that utilizes a dual fluidized bed interconnected by loopseals to selectively separate oxygen from ambient air. This study validated Barracuda-VR® hydrodynamic simulations of dual circulating fluidized bed. The experiments were run on a scaled-down cold-flow unit of a 100 kW dual reactor to find the quantities of interest: circulation rate, bed mass location distribution, and pressure profile. The numerical parameters of time step and grid resolution were studied to find the numeric uncertainty for the quantities of interest. The scenario parameters of flowrates, particle densities, and particle voidage were studied. The uncertainty from the model parameters of tangent-to-wall, drag multiplier, and stress model were studied. Simulation and experimental results matched over some of the parameters studied. These can be used to scale the system back to the 100 kW dual reactor and to a larger system.

Hamilton, Matthew A↗

Energy Storage Grand Challenge - RFI response

Idaho National Laboratory (INL) is operated by Battelle Energy Alliance LLC for the U.S. Department of Energy (DOE). INL conducts research in energy storage (ES) and ancillary fields for several DOE offices including, EERE, NE, FE, and OE. In addition, INL conducts related research for DOD, DHS, state agencies, utilities, and technology developers. INL has developed significant expertise in ES. In July 2020, DOE released the Energy Storage Grand Challenge (ESGC) Roadmap and in conjunction, a Request for Information (RFI) regarding the content of the roadmap. INL is qualified to provide a response to the RFI.

13 HYDRO ENERGY↗

Characterization of CO2 Binding on Alkaline Metal Oxide Sorbents and DFMs for Combined Capture and Conversion

As the world endures environmental crises associated with climate change and the rise of atmospheric CO2 concentrations from anthropogenic CO2 emission, carbon capture and utilization (CCU) technologies are increasingly necessary. Reactive carbon capture (RCC) technologies, in which capture and conversion of CO2 occur in a single reactor, are more energetically and economically attractive by avoiding the need to purify, compress, and transport the captured CO2. To this end, the development of dual function materials (DFM) that enable CO2 capture and conversion to useful C1 products, namely (1) methane, (2) CO, and (3) methanol, are attractive near-term targets for commercial CCU processes for renewable fuels and chemicals. DFM are composed of sorbents and catalysts co-dispersed on the same high surface area carrier. The sorbent component allows for selective capture of CO2 from a gas stream and the catalyst component subsequently performs the in-situ conversion of the adsorbed CO2 upon introduction of a reactive gas (typically H2). The survey of DFM formulations reveals a variety of sorbent+catalyst combinations of interest. There is, however, a lack of depth in fundamental understanding of how the CO2 binds to these materials and how the subsequent reaction mechanisms are affected, which are critical features for the development of next-generation materials with improved performance. To this end, we will describe in this work the CO2 binding characteristics of established and/or new DFM and their sorbent-only counterparts. The surface CO2 binding mechanism and capture capacity will be probed using techniques such as in-situ DRIFTS, operando TGA, and CO2 chemisorption.

alkaline oxides↗