SEARCH · Search NASA

Results for “Time Constant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Thermal performance evaluation of Solar Energy Products Company (SEPCO) 'Soloron' collector tested outdoors

The test article, Model EF-212, Serial Nr. 002, is a single glazed collector with a nonselective absorber plate, using flowing air as the heat transfer medium. The absorber plate and box frame are aluminum and the insulation is one inch isocyanurate foam board with thermal conductivity of 0.11 (BTU/sq ft Hr0/ft.) The tests included the following. (1) time constant test, (2) collector efficiency test, (3) collector stagnation test, (4) incident angle modifier test, (5) load test, (6) weathering test, and (7) absorber plate optical properties test. The results of these tests are tabulated, graphed, or otherwise recorded.

Chiou, J., Sr.↗

NASA NTRS1977

Indoor test for thermal performance evaluation of Lenox-Honeywell solar collector

The test procedures used and the test results obtained from an evaluation test program conducted on a double-covered liquid solar collector under simulated conditions are presented. The test article was a flat plate solar collector using liquid as the heat transfer medium. The absorber plate was steel with the copper tubes bonded on the upper surface. The plate was coated with black chrome with an absorptivity factor of .95 and emissivity factor of .12. A time constant test and incident angle modifier test were conducted to determine the transient effect and the incident angle effect on the collector.

Shih, K.↗

NASA NTRS1977

Indoor thermal performance evaluation of Daystar solar collector

The test procedures used and results obtained from a test program to obtain thermal performance data on a Daystar Model 21B, S/N 02210, Unit 2, liquid solar collector under simulated conditions are described. The test article is a flat plate solar collector using liquid as a heat transfer medium. The absorber plate is copper and coated with black paint. Between the tempered low iron glass and absorber plate is a polycarbonate trap used to suppress convective heat loss. The collector incorporates a convector heat dump panel to limit temperature excursions during stagnation. The following tests were conducted: (1) collector thermal efficiency; (2) collector time constant; (3) collector incident angle modifier; (4) collector heat loss coefficient; and (5) collector stagnation.

Shih, K., Sr.↗

NASA NTRS1977

Indoor test for thermal performance evaluation of Sunworks (liquid) solar collector

Test procedures used and test results obtained from an evaluation test program conducted on a single covered liquid solar collector under simulated conditions are presented. The test article was a flat plate solar collector using water as the heat transfer medium. The absorber plate was copper with copper tubes bonded by soft solder. The plate was coated with Enthone selective black with an absorptivity factor of .87 approximately .92 and an emissivity factor of .10 approximately .20. A time constant test and incident angle modifier test were conducted to determine the transient effect and the incident angle effect on the collector.

Shih, K.↗

NASA NTRS1978

Indoor test for thermal performance evaluation of the Solaron (air) solar collector

The test procedure used and the results obtained from an evaluation test program, conducted to obtain thermal performance data on a Solaron double glazed air solar collector under simulated conditions in a solar simulator are described. A time constant test and incident angle modifier test were also conducted to determine the transient effect and the incident angle effect on the collector. These results and the results of the collector load test are also discussed. The Solaron collector absorber plate is made of 24-gage steel, the coating is baked-on black paint, the cover consists of two sheets of 1/8-inch low-iron tempered glass, and the insulation is one thickness of 3 5/8-inch fiberglass batting.

Source record↗

NASA NTRS1978

Indoor test for thermal performance evaluation on the Sunworks (air) solar collector

The test procedure used and the results obtained from an evaluation test program conducted to obtain thermal performance data on a Sunworks single glazed air solar collector under simulated conditions are described. A time constant test and incident angle modifier test were conducted to determine the transient effect and the incident angle effect on the collector. These results and the results of the collector load test are also discussed.

Source record↗

NASA NTRS1978

Indoor test for thermal performance evaluation on life sciences engineering (air) solar collector

The test procedure used and the results obtained from an evaluation test program conducted to obtain thermal performance data on a life sciences double-glazed air solar collector under simulated conditions is discussed. These tests were made using the Marshall Space Flight Center's solar simulator. A time constant test and incident angle modifier test were also conducted to determine the transient effect and the incident angle effect on the collector. These results and the results of the collector load test are also discussed.

Source record↗

NASA NTRS1978

G-seat system step input and sinusoidal response characteristics

The step input and sinusoidal response characteristics of a pneumatically driven computer controlled G set are examined in this study. The response data show that this system can be modeled as a first order system with an 0.08 sec time lag and a 0.53 sec time constant.

Showalter, T. W.↗

NASA NTRS1977

In-flight gyro drift rate calibration on the Viking Orbiters

The drift rates of the attitude control gyros onboard the Viking Orbiters were calibrated several times during flight. The calibration was performed by engaging the gyro control of attitude for a six-hour period, recording the Viking Orbiter coordinates of the sun and the roll reference star as a function of time, and processing these data by a computer program. The computer program calculated drift rates for each data increment, and then smoothed the calculated rate versus the time function for all the data on the basis of a Gauss-Markov gyro-drift model. The effects of data noise were minimized by using a relatively long time constant in the Gauss-Markov model and by empirically determining a set of corrections for celestial inertial scale factor error differences. In this way the rms error of the data fit was lessened.

Breckenridge, W. G.↗

NASA NTRS1975

The simulated depth history of dust grains in the lunar regolith

Trajectories giving the individual depth variations of lunar dust grains with time are randomly generated by a Monte Carlo code, where the variables are the mass and speed distribution of meteorites at the lunar surface and the geometrical shape of impact craters. A statistical analysis of a great number of such trajectories is then used to define the 'average' depth history of lunar dust grains for two grain radii: 1 and 50 microns. This yields: (1) estimates for time constants involved during the dynamic evolution of the regolith, (2) a model for the layering of the regolith, and (3) a better understanding of the basic dust-grain mechanisms responsible for the formation of the most mature lunar soil samples. The validity of various soil models proposed for the dynamic evolution of the regolith is discussed in terms of experimental constraints on the models.

Duraud, J. P.↗

NASA NTRS1978

On-line parameter estimation using a high sensitivity estimator

An on-line parameter identification method is presented. The method is based on a recursive formulation of the maximum likelihood method, with a significant modification on the gains of the state estimator. In the conventional maximum likelihood method, the Kalman gains are used in the state estimator. This produces unbiased, minimum variance parameter estimates in the presence of process noise and measurement noise, but it also slows the convergence rate when the identification is done on-line. Here we suggest choosing the gains to maximize a measure of the sensitivities of the state estimates to parameter variations. One such criterion is to minimize the trace of the inverse information matrix. This increases the convergence rate significantly. After one or two time constants, the gains are switched to the Kalman values to assure unbiased, minimum-variance estimates. The state estimate will initially be nonoptimal, and may not be adequate for control purposes. In this case, a parallel Kalman filter which uses the identifier's parameter estimates can be used. This method is applied here for the identification of a simple first-order system, and for the identification of short-period stability derivatives of an F-8 aircraft from simulated data.

Mishne, D.↗

NASA NTRS1978

Radiometer at a frequency of 108-120 GHz for study of the earth's atmosphere

Calculated and experimental design and operating characteristics of a 108-120 GHz superheterodyne radiometer with intermediate frequency modulation and a second harmonic frequency converter are presented and discussed. With a 1 sec time constant, the radiometer fluctuation sensitivity threshold is 1 K, without degradation in 2 hours of operation. Graphs of frequency variations, calibration, conversion loss, rectified current, fixed bias voltage, and contact needle impedance are included.

Bordonskiy, G. S.↗

NASA NTRS1977

Evaluation of kinesthetic-tactual displays using a critical tracking task

The study sought to investigate the feasibility of applying the critical tracking task paradigm to the evaluation of kinesthetic-tactual displays. Four subjects attempted to control a first-order unstable system with a continuously decreasing time constant by using either visual or tactual unidimensional displays. Display aiding was introduced in both modalities in the form of velocity quickening. Visual tracking performance was better than tactual tracking, and velocity aiding improved the critical tracking scores for visual and tactual tracking about equally. The results suggest that the critical task methodology holds considerable promise for evaluating kinesthetic-tactual displays.

Jagacinski, R. J.↗

NASA NTRS1977

Analysis of the passive stabilization of the long duration exposure facility

The nominal Long Duration Exposure Facility (LDEF) configurations and the anticipated orbit parameters are presented. A linear steady state analysis was performed using these parameters. The effects of orbit eccentricity, solar pressure, aerodynamic pressure, magnetic dipole, and the magnetically anchored rate damper were evaluated to determine the configuration sensitivity to variations in these parameters. The worst case conditions for steady state errors were identified, and the performance capability calculated. Garber instability bounds were evaluated for the range of configuration and damping coefficients under consideration. The transient damping capabilities of the damper were examined, and the time constant as a function of damping coefficient and spacecraft moment of inertia determined. The capture capabilities of the damper were calculated, and the results combined with steady state, transient, and Garber instability analyses to select damper design parameters.

Siegel, S. H.↗

NASA NTRS1979

INTELSAT 4 in orbit liquid slosh tests and problems in the theoretical analysis of the data

The destabilizing effect of the liquid on attitude nutation stability was determined from an extensive series of inorbit tests. The liquid slosh driving frequency ratio (rotor nutation frequency/rotor spin rate) was varied over the range of 0.58 to 0.70 for the tests by rotating the spacecraft antenna platform at different rates in inertial space. A rotor mounted accelerometer sensed the spacecraft nutation. The observed time constant for the nutation angle increase or decrease was corrected for the stabilizing contribution of the platform mounted pendulum dampers to yield the net destabilizing dedamping contribution from the liquid slosh. The in orbit tests show two unexpected maxima in the dedamping contribution at driving frequency ratios that vary with the propellant loading. The rotor nutation frequency at the maxima was about one-third of the lowest mode liquid slosh frequency given by ground test data for unspun tanks, and thus did not correspond to a simple resonance of the liquid. Ground tests with spinning systems produced the same maxima, but the phenomenon is not yet understood.

Slabinski, V. J.↗

NASA NTRS1979

Indoor test for thermal performance of the Sunmaster evacuated tube (liquid) solar collector

The test procedures used to obtain the thermal performance data for a solar collector under simulated conditions are presented. Tests included a stagnation test, a time constant test, a thermal efficiency test, an incident angle modifier test, and a hot fill test. All tests were performed at ambient conditions and the transient effect and the incident angle effect on the collector were determined. The solar collector is a water working fluid type.

Source record↗

NASA NTRS1979

Indoor test for thermal performance of the GE TC-100 liquid solar collector eight- and ten-tube configuration

The thermal performance of a liquid solar collector was tested in eight- and ten-tube configurations under simulated conditions. A time constant test and an incident angle modifier test were also conducted to determine the transient and incident angle effects on the collector. Performance loss with accessory covers is demonstrated. The gross collector area is about 17.4 ft sq without manifold and 19.1 ft sq with manifold. The collector weight is approximately 60 pounds empty and 75 pounds with manifold.

Source record↗

NASA NTRS1978

Infrared detector performance in the Shuttle Infrared Telescope Facility /SIRTF/

The limitations imposed on infrared detectors for SIRTF are quite different from those imposed on ground-based, balloon-borne, or aircraft-borne systems. The paper examines the limitations and provides performance predictions corresponding to SIRTF conditions. Detector parameters typical of an infrared camera are used. The detector size is taken to be of the order of the diffraction-limited spot, frequency response is taken to correspond to a fraction of a second or less time constant, and spectral definition is provided by multilayer dielectric filters, inductive or capacitive grids, intrinsic absorption, or a combination of these. A nominal 10-micron bandwidth is assumed. The discussion covers atmospheric absorption and emission, zodiacal dust radiance, Shuttle contaminants, telescope self-emission, charged particle radiation, clear environment detector performance, and trapped radiation effects. It is concluded that the SIRTF design and operating conditions will allow current and near-term state-of-the-art detectors to reach their performance limits with SIRTF at a temperature of 10-12 K.

Mccarthy, S. G.↗