Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

High Strain Rate Testing of Welded DOP-26 Iridium

The iridium alloy DOP-26 is used to produce Clad Vent Set cups that protect the radioactive fuel in radioisotope thermoelectric generators (RTGs) which provide electric power for spacecraft and rovers. In a previous study, the tensile properties of DOP-26 were measured over a wide range of strain rates and temperatures and reported in ORNL/TM-2007/81. While that study established the properties of the base material, the fabrication of the heat sources requires welding, and the mechanical properties of welded DOP-26 have not been extensively characterized in the past. Therefore, this study was undertaken to determine the mechanical properties of DOP-26 specimens containing a transverse weld in the center of their gage sections. Tensile tests were performed at room temperature, 750, 900, and 1090°C and engineering strain rates of 1×10 -3 and 10 s -1 . Room temperature testing was performed in air, while testing at elevated temperatures was performed in a vacuum better than 1×10 -4 Torr. The welded specimens had a significantly higher yield stress, by up to a factor of ~2, than the non-welded base material. The yield stress did not depend on the strain rate except at 1090°C, where it was slightly higher for the faster strain rate. The ultimate tensile stress, on the other hand, was significantly higher for the faster strain rate at temperatures of 750°C and above. At 750°C and above, the specimens deformed at 1×10 -3 s -1 showed pronounced necking resulting sometimes in perfect chisel-edge fracture. The specimens deformed at 10 s -1 exhibited this fracture behavior only at the highest test temperature, 1090°C. Fracture occurred usually in the fusion zone of the weld and was, in most cases, primarily intergranular.

36 MATERIALS SCIENCE↗

Report on the Progress of Weld Development of Irradiated Materials at the Oak Ridge National Laboratory

This report summarizes recent welding activities on irradiated alloys in the advanced welding facility at the Radiochemical Engineering Development Center of Oak Ridge National Laboratory and the development of post-weld characterization capabilities and procedures that will be critical for assessing the ability of the advanced welding processes housed within the facility to make successful repairs on irradiated alloys. This facility and its capabilities were developed jointly by the U.S. Department of Energy, Office of Nuclear Energy, Light Water Reactor Sustainability Program and the Electric Power Research Institute, Long Term Operations Program (and the Welding and Repair Technology Center), with additional support from Oak Ridge National Laboratory. The significant, on-going effort to weld irradiated alloys with high Helium concentrations and comprehensively analyze the results will eventually yield validated repair techniques and guidelines for use by the nuclear industry in extending the operational lifetimes of nuclear power plants.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Towards Real Time Diagnostics of Hybrid Welding Laser/GMAW

Methods are currently being developed towards a more robust system real time feedback in the high throughput process combining laser welding with gas metal arc welding. A combination of ultrasonic, eddy current, electronic monitoring, and visual techniques are being applied to the welding process. Initial simulation and bench top evaluation of proposed real time techniques on weld samples are presented along with the concepts to apply the techniques concurrently to the weld process. Consideration for the eventual code acceptance of the methods and system are also being researched as a component of this project. The goal is to detect defects or precursors to defects and correct when possible during the weld process.

36 MATERIALS SCIENCE↗

Monitoring and Control of the Hybrid Laser-Gas Metal-Arc Welding Process

Methods are currently being developed towards a more robust system real time feedback in the high throughput process combining laser welding with gas metal arc welding. A combination of ultrasonic, eddy current, electronic monitoring, and visual techniques are being applied to the welding process. Initial simulation and bench top evaluation of proposed real time techniques on weld samples are presented along with the concepts to apply the techniques concurrently to the weld process. Consideration for the eventual code acceptance of the methods and system are also being researched as a component of this project. The goal is to detect defects or precursors to defects and correct when possible during the weld process.

36 MATERIALS SCIENCE↗

Aluminum Tailor-Welded Blanks for High Volume Automotive Applications

A Design of Experiment based approach is used to systematically investigate relationships between 8 different welding factors (4 related to tool geometry, 4 related to weld process control) and resulting weld properties including strength, elongation and formability in 1.2mm-2mm thick friction stir welding of AA5182-O for TWB application. The factors that result in most significant effects are elucidated. The interactions between several key factors like plunge depth, tool tilt, pin feature and pin length on the overall weld quality is discussed. Appropriate levels of factors that lead to excellent weld properties are also identified.

Aluminum↗

A dual-mesh method for efficient thermal stress analysis of large-scale welded structures

Transient thermo-mechanical analysis of welding problem requires tremendous computation cost. To accelerate the thermal analysis of large-scale welded structures, an efficient computation scheme based on heat transfer localization and dual meshes was proposed. The computation accuracy is guaranteed by a local fine mesh model with size determined by a theoretical solution and a global coarse mesh model with equivalent heat input. The validity and accuracy of the dual-mesh method were verified using an experimental bead-on-plate model. By extending the weld length, the computation time of the proposed method was proved to be almost linearly dependent on the model scale. The thermal analysis of fillet welding of a large panel structure with 6-m-long weld was accelerated by 10 times over conventional finite element analysis and 2.2 times over adaptive mesh method. Meanwhile, the physical memory consumption was also greatly reduced by the dual-mesh method. Such efficient computation method enables fast evaluation of welding stress and distortion which are vital for manufacturing process and structure performance.

36 MATERIALS SCIENCE↗

Microstructure, Chemical Composition and Local Corrosion Behavior of a Friction Stud Welding Joint

In this paper, friction stud welding technology was used to join a stud and base metal, which were composed of X65 steel. The scanning vibrating electrode technique (SVET) and localized electrochemical impedance spectroscopy (LEIS) were used to investigate the localized corrosion behaviors of the welded joint. Scanning electron microscopy, metallographic microscopy and a micro-hardness tester were used to observe the microstructure and measure the hardness of the welded sample. Raman spectrometry and energy-dispersive spectrometry were used to measure the composition of the weldment before and after corrosion, respectively. The results show that there are the maximum micro-hardness and the densest microstructure in the welded zone compared with the other zones. In addition, α-Fe{sub 2}O{sub 3} and Fe{sub 3}O{sub 4} are present in the welded zone. The SVET and LEIS data indicate that the welded zone has the lowest current density and the largest impedance due to the presence of iron oxides and the densest microstructure, thus showing the excellent corrosion resistance. The relationship among microstructure, micro-hardness, chemical composition and local electrochemical behavior was discussed.

36 MATERIALS SCIENCE↗

A Comparative Study of Fracture Toughness at Cryogenic Temperature of Austenitic Stainless Steel Welds

The ITER magnet system is based on the “cable-in-conduit” conductor (CICC) concept, which consists of stainless steel jackets filled with superconducting strands. The jackets provide high strength, limited fatigue crack growth rate and fracture toughness properties to counteract the high stress imposed by, among others, electromagnetic loads at cryogenic temperature. Austenitic nitrogen-strengthened stainless steels have been chosen as base material for the jackets of the central solenoid and the toroidal field system, for which an extensive set of cryogenic mechanical property data are readily available. However, little is published for their welded joints, and their specific performance when considering different combinations of parent and filler metals. Moreover, the impact of post-weld heat treatments that are required for Nb{sub 3}Sn formation is not extensively treated. Welds are frequently responsible for cracks initiated and propagated by fatigue during service, causing structural failure. It becomes thus essential to select the most suitable combination of parent and filler material and to assess their performance in terms of strength and crack propagation at operation conditions. An extensive test campaign has been conducted at 7 K comparing tungsten inert gas (TIG) welds using two fillers adapted to cryogenic service, EN 1.4453 and JK2LB, applied to two different base metals, AISI 316L and 316LN. A large set of fracture toughness data are presented, and the detrimental effect on fracture toughness of post-weld heat treatments (unavoidable for some of the components) is demonstrated. In this study, austenitic stainless steel TIG welds with various filler metals have undergone a comprehensive fracture mechanics characterization at 7 K. These results are directly exploitable and contribute to the cryogenic fracture mechanics properties database of the ITER magnet system. Additionally, a correlation between the impact in fracture toughness and microstructure resulting from the above treatment is provided.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Characterization of Friction-Stir-Welded Dual-Phase Brass

Friction stir welding (FSW) is an ideal process to join brass to avoid the evaporation of zinc. In the present investigation, 6-mm-thick dual-phase brass plates were joined efficiently using FSW at various tool rotational speeds. The microstructures were studied using optical microscopy, electron backscattered diffraction and transmission electron microscopy. The optical micrographs revealed the evolution of various zones across the joint line. The microstructure of the heat-affected zone was similar to that of base metal. The weld zone exhibited finer grains due to dynamic recrystallization. The recrystallization was inhomogeneous and the inhomogeneity reduced with increased tool rotational speed. The dual phase was preserved in the weld zone due to the retention of zinc. The severe plastic deformation created a lot of dislocations in the weld zone. The weld zone was strengthened after welding. The role of tool rotational speed on the joint strength is further reported.

36 MATERIALS SCIENCE↗

Parametric Modeling of AZ31-Mg Alloy Friction Stir Weld Temperature Histories

A parametric model of friction stir weld temperature histories is presented that uses constraint conditions, which are three-dimensional isothermal boundary conditions on the calculated temperature fields. This study describes further extension, with respect to formulation, of a parametric-modeling methodology, which is relatively optimal in terms of representation for application to friction stir welding and processing. These parametric representations of temperature histories can be used for modeling friction stir welds whose process conditions are similar to those in this study. Calculations of AZ31-Mg alloy friction stir weld temperature histories are presented, which use temperature-field constraint conditions based on measured weld cross sections and a model for the estimation of weld stir zone temperatures.

36 MATERIALS SCIENCE↗

Microstructure and Work Hardening Behavior of Micro-plasma Arc Welded AISI 316L Sheet Joint

The aim of this research is to investigate the microstructural changes and work hardening behavior of AISI 316L 0.5-mm-thick sheet due to micro-plasma arc welding. AISI 316L similar sheets were welded in single-pass square butt joint configuration. The microstructure in the fusion zone typically contains a variety of complex δ-ferrite-austenitic structure, which significantly increased hardness value compared to the base material because of rapid solidification of the weld pool. Systematic tensile test was performed to investigate strain rate sensitivity of the welded joint under quasi-static loading conditions. The multistage work hardening behavior was determined by Kocks–Mecking (K–M) model and differential Crussard–Jaoul analysis. In both the cases, stage III work hardening behavior and stage IV work hardening behavior were observed. The stress–strain curves of welded specimen at different strain rates were analyzed in terms of Hollomon, Ludwik and Swift equations to determine work hardening exponent values. The welded joints were ruptured in the transition zone of heat affected and fusion zones. The fractographic observation exhibited variation in dimple and void density over strain rate from 0.0001 to 0.0015 s{sup −1}.

36 MATERIALS SCIENCE↗

Microstructural Characteristics and Mechanical Properties in the Laser Beam Welded Joints of High-Strength Microalloyed Steel

The laser beam welded joints of the high-strength microalloyed steel consist of the base metal (BM), the partially transformed heat-affected zone I (PTHAZ-I), the partially transformed heat-affected zone II (PTHAZ-II), the fully transformed heat-affected zone (FTHAZ) and the fusion zone (FZ). The martensite/austenite (M/A) islands of the bainites in the PTHAZ-II are dense versus those in the PTHAZ-I, and the martensites exist in the FTHAZ and the FZ together with the bainites under the slow welding speed. The M/A islands of the bainites and/or the martensites in the PTHAZ become denser under the high welding speed, and the martensites in the FTHAZ and the FZ predominate. The low-angle boundary density and the high local misorientation proportion are used to identify the constituents roughly, consistent with the microstructural characteristics in the welded joints. The misorientation angle distributions are employed to evaluate the degree of the phase transformation, reflecting the change law of the degree of the phase transformation in the welded joints. The hardness and the tensile tests indicate that the HAZ and the FZ are stronger than the BM, dependent on the microstructures in the welded joints. The strengthening in the HAZ and the FZ is mainly attributed to the products of non-equilibrium phase transformation with the high dislocation density.

36 MATERIALS SCIENCE↗

A Weighting Grade-Based Optimization Method for Determining Refill Friction Stir Spot Welding Process Parameters

The welding process used in fabricating thin-walled structures by refill friction stir spot welding (RFSSW) should be characterized by a high strength of welds and high process repeatability which is demonstrated by a small dispersion of the load capacity of the joints. The present work is designed to optimize RFSSW process parameters for 7075-T6 Alclad aluminum alloy sheets used to fabricate aircraft structures. The optimization was performed by scalarization of the objective function using the weighting grades method. The study considers the effect of process parameters, i.e., tool plunge depth, duration of welding, tool rotational speed, on the tensile/shear strength of the joints, and dispersion of the load capacity. It was found that it was possible to choose the optimal welding parameters taking into account maximization of the load capacity and minimization of the dispersion of the joint strength via a best compromise between the tool rotational speed ensuring adequate plasticization of the base material and the duration of welding ensuring that a fine-grained joint microstructure is obtained.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Behavior of Friction Stir-Welded Sc-Modified Al-Zn-Mg Alloys Made Using Different Base Metal Tempers

The microstructure and property of friction stir weld joints of a Sc-modified Al-Zn-Mg alloy developed using base metal in hot-rolled (HR) and T6 temper were studied and compared in this work. The results showed that the microstructure and property exhibited significant difference between the two friction stir weld joints. The weld efficiency of the FSW joint developed using base metal in HR condition is over 90%, while that of the FSW joint developed using base metal in T6 condition is only 70%. The hardness of the weld nugget of HR joint is obviously higher than that of the weld nugget of T6 joint, due to the different changes in the original precipitates during the friction stir welding process. The strengthening mechanism in different zones of the two FSW joints was discussed to examine the microstructure–properties relationship, and the main difference of the strengthening mechanism between the two FSW joints was revealed.

36 MATERIALS SCIENCE↗

Failure Analysis of Pinch Weld Electrodes

We present that Savannah River Site uses brazed copper/tungsten electrodes for a specialized weld referred to as a pinch weld. An alternative method to produce the pinch weld electrodes was sought to improve quality and to reduce the manufacturing steps. Backcasting of pinch weld electrodes was selected as such a process. During preliminary testing, deformation of the electrodes was observed. A failure analysis assessment was conducted and the strength of the electrodes was found to be significantly less than required to enable welding of the tubes. This assessment includes compression testing metallographic analysis. The pinch weld electrodes fabricated by backcasting do not meet the requirements with respect to strength. Additionally, a minimum strength requirement for conventionally prepared electrodes is recommended.

36 MATERIALS SCIENCE↗

The effect of filament peaking on electron beam weld quality

Electron beam welding uses high intensity beams that are generated by an electron emitting cathode under high vacuum conditions. The cathode, typically a ribbon or wire filament of refractory metal, must be heated to sufficiently high temperatures for electron emission to occur and must be carefully controlled to produce the desired beam current while at the same time optimizing filament lifetime. Traditional methods for doing this in commonly used triode gun assemblies consist of first finding the filament knee point in the filament current versus beam current relationship that produces the desired beam current for a given beam voltage. The filament current is then increased by some amount, typically 5–10%, per conventional wisdom to produce a peaked beam. This investigation studies and quantifies the beam and weld quality produced by underkneed and overpeaked filaments using electron beam diagnostics to measure the power density distribution of these beams. Underkneed filaments are shown to have power densities that drop off very quickly below the traditional knee, resulting in poor weld penetration. Kneed filaments do not reach the full beam intensity and also produce shallow welds. Increasing the filament current 10% above the traditional knee was shown to produce a circular Gaussian-like beam with peaked intensity optimized for welding and for filament lifetime. Further increases in the filament current that produce overpeaked beams do not significantly change the beam or weld quality and would only contribute to a reduced filament lifetime.

Electron Beam Welding↗

Hydrogen accelerated fatigue crack growth of friction stir welded X52 steel pipe

Friction stir welded steel pipelines were tested in high pressure hydrogen gas to examine the effects of hydrogen accelerated fatigue crack growth. Fatigue crack growth rate (da/dN) vs. stress-intensity factor range (ΔK) relationships were measured for an X52 friction stir welded pipe tested in 21 MPa hydrogen gas at a frequency of 1 Hz and R = 0.5. Tests were performed on three regions: base metal (BM), center of friction stir weld (FSW), and 15 mm off-center of the weld. For all three material regions, tests in hydrogen exhibited accelerated fatigue crack growth rates that exceeded an order of magnitude compared to companion tests in air. Among tests in hydrogen, fatigue crack growth rates were modestly higher in the FSW than the BM and 15 mm off-center tests. Select regions of the fracture surfaces associated with specified ΔK levels were examined which revealed intergranular fracture in the BM and 15 mm off-center specimens but an absence of intergranular features in the FSW specimens. In conclusion, the X52 friction stir weld and base metal tested in hydrogen exhibited fatigue crack growth rate relationships that are comparable to those for conventional arc welded steel pipeline of similar strength found in the literature.

08 HYDROGEN↗

Adaptively remeshed multiphysical modeling of resistance forge welding with experimental validation of residual stress fields and measurement processes

Welding processes used in the production of pressure vessels impart residual stresses in the manufactured component. Computational modeling is critical to predicting these residual stress fields and understanding how they interact with notches and flaws to impact pressure vessel durability. Here, in this work, we present a finite element model for a resistance forge weld and validate it using laboratory measurements. Extensive microstructural changes, near-melt temperatures, and large localized deformations along the weld interface pose significant challenges to Lagrangian finite element modeling. The proposed modeling approach overcomes these roadblocks in order to provide a high-fidelity simulation that can predict the residual stress state in the manufactured pressure vessel; a rich microstructural constitutive model accounts for material recrystallization dynamics, a frictional-to-tied contact model is coordinated with the constitutive model to represent interfacial bonding, and adaptive remeshing is employed to alleviate severe mesh distortion. An interrupted-weld approach is applied to the simulation to facilitate comparison to displacement measures. Several techniques are employed for residual stress measurement in order to validate the finite element model: neutron diffraction, the contour method, and the slitting method. Model-measurement comparisons are supplemented with detailed simulations that reflect the configurations of the residual-stress measurement processes themselves. The model results show general agreement with experimental measurements, and we observe some similarities in the features around the weld region. Factors that contribute to model-measurement differences are identified. Finally, we conclude with some discussion of the model development and residual stress measurement strategies, including how to best leverage the efforts put forth here for other weld problems.

36 MATERIALS SCIENCE↗