Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wind Tunnels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Performance results from a test of an S-76 rotor in the NASA Ames 80- by 120-foot wind tunnel

A full-scale helicopter rotor wind tunnel test has been conducted which covers a wide range of rotor-shaft angles-of-attack and 0-100 kt thrust conditions. The hover performance data thus obtained were compared with the results of momentum theory calculations; forward flight rotor-performance data were compared with calculations from a comprehensive rotorcraft analysis. These comparisons suggest that hover testing at an outdoor facility in the absence of ground effect is required to make a final determination of the absolute accuracy of the wind tunnel hover data.

Shinoda, Patrick M.↗
NASA NTRS1973

Aspects of large-scale, subsonic, wind-tunnel design for propulsion noise research

The case for full-scale acoustic testing of propulsion systems at flight conditions and the use of wind tunnels for this work are discussed. The problems associated with measuring noise in wind tunnels are discussed, and wind-tunnel design requirements to provide a useful facility for noise research are established. Full-scale subsonic wind-tunnel designs that meet the requirements are described, and it is shown that state-of-art acoustics technology must be used in the drive-fan design to minimize background noise. If this is successfully done, acoustic treatment in the drive system area may be avoided.

Hickey, D. H.↗
NASA NTRS1988

An experimental study of an adaptive-wall wind tunnel

A series of adaptive wall ventilated wind tunnel experiments was carried out to demonstrate the feasibility of using the side wall pressure distribution as the flow variable for the assessment of compatibility with free air conditions. Iterative and one step convergence methods were applied using the streamwise velocity component, the side wall pressure distribution and the normal velocity component in order to investigate their relative merits. The advantage of using the side wall pressure as the flow variable is to reduce the data taking time which is one the major contributors to the total testing time. In ventilated adaptive wall wind tunnel testing, side wall pressure measurements require simple instrumentation as opposed to the Laser Doppler Velocimetry used to measure the velocity components. In ventilated adaptive wall tunnel testing, influence coefficients are required to determine the pressure corrections in the plenum compartment. Experiments were carried out to evaluate the influence coefficients from side wall pressure distributions, and from streamwise and normal velocity distributions at two control levels. Velocity measurements were made using a two component Laser Doppler Velocimeter system.

Celik, Zeki↗
NASA NTRS1980

Application of two design methods for active flutter suppression and wind-tunnel test results

The synthesis, implementation, and wind tunnel test of two flutter suppression control laws for an aeroelastic model equipped with a trailing edge control surface are presented. One control law is based on the aerodynamic energy method, and the other is based on results of optimal control theory. Analytical methods used to design the control laws and evaluate their performance are described. At Mach 0.6, 0.8, and 0.9, increases in flutter dynamic pressure were obtained but the full 44 percent increase was not achieved. However at Mach 0.95, the 44 percent increase was achieved with both control laws. Experimental results indicate that the performance of the systems is not so effective as that predicted by analysis, and that wind tunnel turbulence plays an important role in both control law synthesis and demonstration of system performance.

Newsom, J. R.↗
NASA NTRS1984

A numerical simulation of three-dimensional flow in an adaptive wall wind tunnel

Numerical simulations of three dimensional flows in a prototype adaptive wall wind tunnel are conducted at the Mach number of 0.6 to investigate: (1) wind tunnel wall interference, (2) active streamline control by varying air removal or injection along the walls, and (3) to develop a method for establishing wall boundary conditions for interference free flows. Wind tunnel wall interference could be controlled by using only the vertical velocity components. For the configuration tested, interference free flow with solid sidewalls can be approximated by using only floor and ceiling blowing/suction.

Mendoza, J. P.↗
NASA NTRS1996

Modeling the Benchmark Active Control Technology Wind-Tunnel Model for Application to Flutter Suppression

This paper describes the formulation of a model of the dynamic behavior of the Benchmark Active Controls Technology (BACT) wind-tunnel model for application to design and analysis of flutter suppression controllers. The model is formed by combining the equations of motion for the BACT wind-tunnel model with actuator models and a model of wind-tunnel turbulence. The primary focus of this paper is the development of the equations of motion from first principles using Lagrange's equations and the principle of virtual work. A numerical form of the model is generated using values for parameters obtained from both experiment and analysis. A unique aspect of the BACT wind-tunnel model is that it has upper- and lower-surface spoilers for active control. Comparisons with experimental frequency responses and other data show excellent agreement and suggest that simple coefficient-based aerodynamics are sufficient to accurately characterize the aeroelastic response of the BACT wind-tunnel model. The equations of motion developed herein have been used to assist the design and analysis of a number of flutter suppression controllers that have been successfully implemented.

Waszak, Martin R.↗
NASA NTRS1982

Comparison of Flight Measured, Predicted and Wind Tunnel Measured Winglet Characteristics on a KC-135 Aircraft

One of the objectives of the KC-135 Winglet Flight Research and Demonstration Program was to obtain experimental flight test data to verify the theoretical and wind tunnel winglet aerodynamic performance prediction methods. Good agreement between analytic, wind tunnel and flight test performance was obtained when the known differences between the tests and analyses were accounted for. The flight test measured fuel mileage improvements for a 0.78 Mach number was 3.1 percent at 8 x 10(5) pounds W/delta and 5.5 percent at 1.05 x 10(6) pounds W/delta. Correcting the flight measured data for surface pressure differences between wind tunnel and flight resulted in a fuel mileage improvement of 4.4 percent at 8 x 10(5) pounds W/delta and 7.2 percent at 1.05 x 10(6) pounds W/delta. The performance improvement obtained was within the wind tunnel test data obtained from two different wind tunnel models. The buffet boundary data obtained for the baseline configuration was in good agreement with previous established data. Buffet data for the 15 deg cant/-4 deg incidence configuration showed a slight improvement, while the 15 deg cant/-2 deg incidence and 0 deg cant/-4 deg incidence data showed a slight deterioration.

Dodson, R. O., Jr.↗
NASA NTRS1976

Wind tunnel wall interference effects on a supercritical airfoil at transonic speeds

Wind tunnel tests of a 10% supercritical airfoil have been conducted in the Lockheed Compressible Flow Facility at transonic speeds to determine the effects of varying wind tunnel wall porosity on airfoil performance. Wall configurations ranging in porosity from 1.3% to 10% were investigated at Reynolds numbers of 7 to 30 million. Experimental data presented to show the effect of varying wall porosity include airfoil surface pressures, airfoil forces, and wind tunnel wall pressures. Utilizing the experimental results, an assessment of the applicability of current subcritical theoretical methods to predict wall interference corrections in subsonic and transonic flows is made.

Blackwell, J. A., Jr.↗
NASA NTRS1999

Pressure-Sensitive Paint and Video Model Deformation Systems at the NASA Langley Unitary Plan Wind Tunnel

Pressure-sensitive paint (PSP) and video model deformation (VMD) systems have been installed in the Unitary Plan Wind Tunnel at the NASA Langley Research Center to support the supersonic wind tunnel testing requirements of the High Speed Research (HSR) program. The PSP and VMD systems have been operational since early 1996 and provide the capabilities of measuring global surface static pressures and wing local twist angles and deflections (bending). These techniques have been successfully applied to several HSR wind tunnel models for wide ranges of the Mach number, Reynolds number, and angle of attack. A review of the UPWT PSP and VMD systems is provided, and representative results obtained on selected HSR models are shown. A promising technique to streamline the wind tunnel testing process, Modern Experimental Design, is also discussed in conjunction with recently-completed wing deformation measurements at UPWT.

Erickson, G. E.↗
NASA NTRS1999

Pressure-Sensitive Paint and Video Model Deformation Systems at the NASA Langley Unitary Plan Wind Tunnel

Pressure-sensitive paint (PSP) and video model deformation (VMD) systems have been installed in the Unitary Plan Wind Tunnel at the NASA Langley Research Center to support the supersonic wind tunnel testing requirements of the High Speed Research (HSR) program. The PSP and VMD systems have been operational since early 1996 and provide the capabilities of measuring global surface static pressures and wing local twist angles and deflections (bending). These techniques have been successfully applied to several HSR wind tunnel models for wide ranges of the Mach number, Reynolds number, and angle of attack. A review of the UPWT PSP and VMD systems is provided, and representative results obtained on selected HSR models are shown. A promising technique to streamline the wind tunnel testing process, Modern Experimental Design, is also discussed in conjunction with recently-completed wing deformation measurements at UPWT.

Erickson, G. E.↗
NASA NTRS1989

Comparison of conventional and adaptive wall wind tunnel results with regard to Reynolds number effects

A comparison of results from conventional and adaptive wall wind tunnels with regard to Reynolds number effects was carried out. The special objective of this comparison was to confirm or reject earlier conclusions, soley based on conventional wind tunnel results, concerning the influence of viscous effects on the characteristics of partially open wind tunnel walls, hence wall interference. The following postulations could be confirmed: (1) certain classes of supercritical airfoils exhibit a non-linear increase in lift which is, at least in part, related to viscous-inviscid interactions on the airfoil. This non-linear lift characteristic can erroneously be suppressed by sidewall interference effects in addition to being affected by changes in Reynolds number. Adaptive walls seem to relieve the influence of sidewall interference; (2) the degree of (horizontal) wall interference effects can be significantly affected by changes in Reynolds number, thus appearing as true Reynolds number effects; (3) perforated wall characteristics seem much more susceptible to viscous changes than the characteristics of slotted walls; here, blockage interference may be most severely influenced by viscous changes; and (4) real Reynolds number effects are present on the CAST 10-2/DOA 2 airfoil; they were shown to be appreciable also by the adaptive wall wind tunnel tests.

Stanewsky, E.↗
NASA NTRS1976

The rationale and design features for the 40 by 80/80 by 120 foot wind tunnel

A substantial increase in the test capability of full scale wind tunnels is considered. In order to determine the most cost effective means for providing this desired increase in test capability, a series of design studies were conducted of various new facilities as well as of major modifications to the existing 40- by 80-foot wind tunnel. The most effective trade between test capability and facility cost was provided by repowering the existing 40 by 80 foot wind tunnel to increase the maximum speed from 200 knots to 300 knots and by the addition of a new 80- by 120-foot test section having a 110 knot maximum speed. The design of the facility is described with special emphasis on the unique features, such as the drive system which absorbs nearly four times the power without an increase in noise, and the large flow diversion devices required to interface the two test sections to a single drive.

Mort, K. W.↗
NASA NTRS2013

FUN3D Airload Predictions for the Full-Scale UH-60A Airloads Rotor in a Wind Tunnel

An unsteady Reynolds-Averaged Navier-Stokes solver for unstructured grids, FUN3D, is used to compute the rotor performance and airloads of the UH-60A Airloads Rotor in the National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-foot Wind Tunnel. The flow solver is loosely coupled to a rotorcraft comprehensive code, CAMRAD-II, to account for trim and aeroelastic deflections. Computations are made for the 1-g level flight speed-sweep test conditions with the airloads rotor installed on the NFAC Large Rotor Test Apparatus (LRTA) and in the 40- by 80-ft wind tunnel to determine the influence of the test stand and wind-tunnel walls on the rotor performance and airloads. Detailed comparisons are made between the results of the CFD/CSD simulations and the wind tunnel measurements. The computed trends in solidity-weighted propulsive force and power coefficient match the experimental trends over the range of advance ratios and are comparable to previously published results. Rotor performance and sectional airloads show little sensitivity to the modeling of the wind-tunnel walls, which indicates that the rotor shaft-angle correction adequately compensates for the wall influence up to an advance ratio of 0.37. Sensitivity of the rotor performance and sectional airloads to the modeling of the rotor with the LRTA body/hub increases with advance ratio. The inclusion of the LRTA in the simulation slightly improves the comparison of rotor propulsive force between the computation and wind tunnel data but does not resolve the difference in the rotor power predictions at mu = 0.37. Despite a more precise knowledge of the rotor trim loads and flight condition, the level of comparison between the computed and measured sectional airloads/pressures at an advance ratio of 0.37 is comparable to the results previously published for the high-speed flight test condition.

Lee-Rausch, Elizabeth M.↗
NASA NTRSDate not supplied

Mars Sample Return, Sample Retrieval Lander, Reaction Control System Jet Interaction Supersonic Wind Tunnel Test Overview with CFD Predictions

NASA's Mars Sample Return campaign will be launching several missions over the next decade that will work together to return rock samples from Mars back to Earth. The Sample Retrieval Lander (SRL) will deliver the Mars Ascent Vehicle and fetch rover to the surface of Mars in 2006. Rock samples collected by the Mars 2020 Perseverance rover, landing in early 2021, will be loaded on the the ascent vehicle to be launched into Mars orbit for retrieval by yet another spacecraft. The Sample Retrieval Lander will be a blunt entry capsule similar to past Mars entry vehicles like Mars Science Laboratory and Viking. The vehicle will fly a guided entry, using a small lift vector produced by a non-zero trim angle of attack to eliminate downrange and crossrange position errors at the point of parachute deploy. This energy and heading management is achieved with a reaction control system (RCS) that directs the bank angle of the vehicle and also minimizes unwanted capsule dynamics. The reaction control system and control design is based on the Mars Science Laboratory and Mars 2020 RCS systems. However, due to packaging constraints, the backshell of this new entry vehicle has a different geometry than those earlier designs. To certify the RCS system for flight the project must characterize the jet plume interactions with the capsule backshell that could impair or significantly augment the RCS control authority. This characterization will be done through a combination of computational fluid dynamics (CFD) analysis and wind tunnel test. Two candidate arrangements of the RCS jets have been identified for the SRL vehicle and are currently under evaluation before final selection. The aero/RCS plume interactions of these candidate configurations have been measured in a supersonic wind tunnel test in NASA Langley's Unitary Plan Wind Tunnel. The test was conducted in the fall of 2020 and data is currently being reduced. An overview of the candidate RCS configurations are presented here with an overview of the wind tunnel model design, jet scaling and scaled nozzle design, and the test matrix. Preliminary CFD runs are presented with an assessment of the predicted plumes and their interaction with the wake flow of the vehicle. The predicted effects of the model sting is provided as well. This high fidelity wind tunnel test is being conducted much earlier in the SRL project than would normally be done. The test was funded as part of a CFD evaluation task funded by NASA's Aerosciences Evaluation and Test Capabilities Project. The objective of the evaluation task was to compare the ability of CFD to predict complex flows with data that can be measured in the Langley Unitary Plan Wind Tunnel. RCS Jet interactions were selected as a type of complex flow that is important to NASA missions. In addition to providing useful data to the SRL project, there was added emphasis on quantifying the accuracy of the CFD predictions and wind tunnel test data. An overview of the uncertainty quantification methodologies for computational and experimental portions of this test is presented.

blunt body↗
NASA NTRS1980

TWINTAN: A program for transonic wall interference assessment in two-dimensional wind tunnels

A method for assessing the wall interference in transonic two dimensional wind tunnel test was developed and implemented in a computer program. The method involves three successive solutions of the transonic small disturbance potential equation to define the wind tunnel flow, the perturbation attriburable to the model, and the equivalent free air flow around the model. Input includes pressure distributions on the model and along the top and bottom tunnel walls which are used as boundary conditions for the wind tunnel flow. The wall induced perturbation fields is determined as the difference between the perturbation in the tunnel flow solution and the perturbation attributable to the model. The methodology used in the program is described and detailed descriptions of the computer program input and output are presented. Input and output for a sample case are given.

Kemp, W. B., Jr.↗
NASA NTRS1992

Progress of magnetic suspension and balance systems for wind tunnels in the USSR

Magnetic Suspension and Balance Systems (MSBS) for wind tunnels are being developed in order to solve the principal problems of aerodynamics which cannot be solved by conventional means: (1) measurements of aerodynamic loads acting on the aircraft models without the effects of mechanical supporting devices; and (2) the study of base pressure. This paper traces the progress of MSBS for wind tunnels in the Commonwealth of Independent States (CIS). The paper describes electromagnetic configuration, position sensing, and control and calibration systems of two wind tunnel MSBS existing in the CIS. The features of high-angle-of-attack control and roll control are discussed. The results of preliminary experiments on high-angle-of-attack and roll controls, digital control, and aerodynamic testing are also presented.

Kuzin, A. V.↗
NASA NTRS2016

Wind Tunnel Model Design for Sonic Boom Studies of Nozzle Jet with Shock Interactions

NASA and Industry are performing vehicle studies of configurations with low sonic boom pressure signatures. The computational analyses of modern configuration designs have matured to the point where there is confidence in the prediction of the pressure signature from the front of the vehicle, but uncertainty in the aft signatures with often greater boundary layer effects and nozzle jet pressures. Wind tunnel testing at significantly lower Reynolds numbers than in flight and without inlet and nozzle jet pressures make it difficult to accurately assess the computational solutions of flight vehicles. A wind tunnel test in the NASA Ames 9- by 7-Foot Supersonic Wind Tunnel from Mach 1.6 to 2.0 will be used to assess the effects of shocks from components passing through nozzle jet plumes on the sonic boom pressure signature and provide datasets for comparison with CFD codes. A large number of high-fidelity numerical simulations of wind tunnel test models with a variety of shock generators that simulate horizontal tails and aft decks have been studied to provide suitable models for sonic boom pressure measurements using a minimally intrusive pressure rail in the wind tunnel. The computational results are presented and the evolution of candidate wind tunnel models is summarized and discussed in this paper.

Wind↗