Search NASA⌕ Search

SEARCH · Search NASA

Results for “acetate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Comparing hydrothermal sintering and cold sintering process: Mechanisms, microstructure, kinetics and chemistry

In this study, we report the sintering of zinc oxide (ZnO) through the comparison between the hydrothermal sintering (HS) and the cold sintering process (CSP) operating in closed and open conditions, respectively. Sintering was performed at 155 ± 5 °C applying a pressure of 320 MPa, and during different holding times (0 min, 20 min, 40 min and 80 min). Whatever the low sintering process used, ceramics characteristics are almost similar in terms of relative densities and ZnO structure. However, several differences such as the nature of stabilized phases, grain sizes and quantities of residual molecules in the densified pellets, were characterized and explained. The formation of zinc acetate “bridges” was observed ex situ in hydrothermally sintered samples. Lastly, a detailed ReaxFF molecular dynamics simulation was performed to help understand the formation mechanisms of zinc acetate “bridges” and compare the chemical activities between HS and CSP.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis of UO 2 nanoparticles via coulometric titration: influence of electrolytes and ligands on synthesized particle properties

Here, this study investigates the controlled synthesis of uranium oxide nanoparticles (UO 2 NPs) via coulometric titration under ambient conditions, focusing on the impact of electrolyte anions, salt concentrations, and strongly complexing ligands on particle formation and properties. Using dilute solutions of mineral acids (HNO 3 , HCl, and HClO 4 ), we demonstrate that the choice of electrolyte anion affects particle size, polydispersity, and surface charge. Particle characterization using dynamic light scattering and transmission electron microscopy shows that particles synthesized in perchlorate are largest and show a high degree of polydispersity. In comparison, particles synthesized in chloride are smaller and more uniform in size. Synthesis in nitrate yields a wide variety of particle sizes, with the major fraction (>65 %) having a smaller size than that obtained in the other two electrolytes. The presence of more strongly coordinating ligands such as sulfate and acetate modulate hydrolysis and condensation reactions, with sulfate suppressing nanoparticle formation across a wide concentration range ([SO 4 2- ] > 5 mM) and acetate enabling stable colloidal suspensions at [HOAc] ≤ 0.1 M. Synthesis in concentrated electrolytes (2 M NaNO 3 , NaCl, or NaClO 4 ) accelerates reaction kinetics but introduces challenges, as particles showed increased polydispersity and aggregation, and were more prone to oxidation. Electrolyte effects on actinide oxide nanoparticle formation are discussed and a short comparison to established nanoparticle syntheses is drawn. This work underscores the importance of tailoring synthesis parameters to achieve desired nanoparticle properties, providing valuable insights for optimizing UO 2 NP production for various applications.

Actinide hydrolysis↗
DOE OSTI2022

Vacuum-ultraviolet absorption cross-sections of functionalized four-carbon species

Absorption cross-sections were measured in the vacuum ultraviolet from 5.17 – 9.92 eV using differential absorption spectroscopy for 33 four-carbon species: n-butane, trans-2-butene, cis-2-butene, butanal, butyric acid, ethyloxirane, trans-2,3-dimethyloxirane, cis-2,3-dimethyloxirane, 2-methyloxetane, 2,2'-bioxirane, vinyl oxirane, 3,4-epoxybutan-2-one, diacetyl, diethyl ether, ethyl vinyl ether, vinyl acetate, acetic anhydride, 1-butanol, 3-buten-1-ol, 1–hydroxy-butan-2-one, 1–hydroxy-butan-3-one, 2,3-epoxybutan-1-ol, 3,4-epoxybutan-1-ol, 2-oxetanemethanol, butanone, methyl vinyl ketone, 4H-1,3-dioxine, allyl formate, 2-oxobutanal, 4-hydroxybutanal, 2-methyloxetan-3-one, cis–but-2-en-1-ol, and trans-2–but-enal. Uncertainties were quantified in all cases by accounting for errors in gas-phase concentration, experimental repeatability, and signal-to-noise ratio as a function of photon energy. With the exception of 2-oxobutanal, which is reported with an uncertainty of 10%, convolving the sources of error using the root-sum-square method led to an upper limit of 5% uncertainty above the detection limit, which is largely attributable to chemical purity. Here, the primary objective of the present work is to provide absolute cross-sections along with quantified uncertainty limits. The majority of the absorption spectra, which reflect electronic transitions such as σ → σ* and n → σ*, are reported for the first time and provide insight into fundamental chemical physics, such as vibrational band structure and Rydberg transitions. The quantitative spectra in the present work facilitates the discovery of chemical intermediates that support improvement in the accuracy of computational models for low-temperature combustion and atmospheric chemistry.

biofuels↗
DOE OSTI2020

Structural characterization of sugarcane lignins extracted from different protic ionic liquid pretreatments

Previous studies based on protic ionic liquids have shown them to be effective for extracting lignins from biomass. Moreover, ILs synthesized with amine cations can promote the insertion of nitrogen into lignin, favoring its valorization for industrial applications. Here, lignins extracted from sugarcane bagasse by eight different PILs were analyzed. Several techniques of characterization were employed (2D HSQC NMR, 31P NMR, GPC, Py-GC/MS, TGA, FTIR, and elemental analysis), seeking a deeper understanding of lignin structure post-PILS treatment. In particular, lignin obtained with acetate and lactate anions with monoethanolamonium cations showed similar structural compositions. Lignins obtained from ethylenediamonium cation combined anions acetate and lactate exhibited relatively higher molecular weights compared to the other lignins studied. The elemental analysis of these lignins further revealed the presence of nitrogen in their structures, suggesting that amination occurred. In this work we used PILs not yet reported in the literature for this purpose, and consequently obtained lignins with specific structures. Overall, our results demonstrated that depending on the PILs used, lignins with distinct properties could be obtained which might be used for value-added applications. This work covered new advances in elucidation of lignin chemical structure and opened a new path for lignin valorization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Ambient-Pressure Chemical Recycling of Thermoset Carbon Fiber-Reinforced Polymers via Low-Temperature Solvolysis: Techno-Economic and Life-Cycle Assessment

Carbon fiber-reinforced polymer (CFRP) waste is rapidly accumulating, with global volumes projected to exceed 500,000 tons annually by 2050. Virgin carbon fiber production is extremely energy- and cost-intensive, and growing demand has intensified supply-chain vulnerabilities associated with precursor availability and reliance on critical materials. Scalable recycling technologies therefore offer not only environmental benefits but also opportunities to reduce material costs and strengthen domestic composite supply chains. This study introduces an efficient, mild chemical recycling method for epoxy-amine CFRPs, utilizing acetic acid (80 wt%) and zinc acetate (1 wt%) at atmospheric pressure and low temperature (~110 °C). The solvolysis process preserves residual resin (~40%) on recycled carbon fibers (rCF), enhancing interfacial bonding in remanufactured composite materials. Recycled fibers retain ~90% of their mechanical properties, and recovered oligomers show potential for reuse in epoxy formulations, supporting material circularity. Techno-economic analysis (TEA) and life-cycle assessment (LCA) confirm the scalability and sustainability of this process.

Recycling CFRP↗
DOE OSTI2020

Mercury methylation potential in a sand dune on Lake Michigan's eastern shoreline

Lake Michigan hosts the largest freshwater sand dune system in the world and is economically important for the fishery industry and tourism. Due to industrial pollution and atmospheric mercury (Hg) deposition, toxic levels of methylmercury (MeHg) have been found in the Lake biota, but little information is known regarding MeHg sources and Hg methylation potential in the shoreline sand dunes. In this study, we conducted anaerobic incubation experiments with beach sands collected from Ludington, Michigan, and examined the effects of organic carbon substrate addition, inorganic nitrogen, and mineral magnetite on Hg methylation. Despite nutrient poor and low-organic carbon conditions, appreciable Hg methylation activity coupled with carbon degradation was observed in the sands. Addition of acetate as a carbon source substantially increased MeHg production from 2 to 380 ng/kg sediment while acetate was rapidly degraded in the first 19 days of incubation. Ammonium addition showed little influence on carbon degradation or Hg methylation, whereas iron oxide addition (~1% dry weight) significantly inhibited both carbon degradation and MeHg production (by up to 90%), highlighting strongly coupled interactions between microbes, carbon substrates, and minerals. This research demonstrates the potential of microbial Hg methylation in the sand dunes, which may play a role in MeHg input and bioaccumulation in the Lake Michigan ecosystem.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Durability of ionomer encapsulants in photovoltaic modules

Ethylene vinyl acetate (EVA) has for decades been the preferred material for photovoltaic (PV) module encapsulation. However, while it is relatively inexpensive and initially adheres well to module components, EVA discolors with age and - as interfacial adhesion degrades - becomes susceptible to delamination, ultimately resulting in reduced module efficiency and shortened service lifetimes. As potential replacements for EVA, ionomer thermoplastic materials cure faster, are more resistant to discoloration and potential induced degradation, and do not evolve corrosive acetic acid, making them compatible with new device materials such as perovskites. Since there is limited information on ionomer durability for PV module applications, a series of field and accelerated laboratory aging studies were conducted to assess ionomer interface stability in the presence of terrestrial environmental stressors. It is shown that adhesion to the glass and cell interfaces of PV modules is inferior to EVA, both before and after aging, rendering ionomers particularly susceptible to delamination after short timeframes. Potential solutions to improve ionomer adhesion are discussed.

14 SOLAR ENERGY↗
DOE OSTI2021

Toward the Understanding of the Reaction Mechanism of Zn/MnO2 Batteries Using Non-alkaline Aqueous Electrolytes

Zn/MnO 2 systems using non-alkaline aqueous electrolytes have attracted tremendous interest as rechargeable aqueous Zn ion batteries due to their safety and high specific capacities. Despite their promising electrochemical performance, however, their reaction mechanism has remained elusive. Here in this paper, we examined the structural evolution of cryptomelane α-MnO 2 cathode by ex situ transmission electron microscopy after electrochemical testing using two different non-alkaline aqueous Zn electrolytes with acetate and triflate salts of different pH values. We have discovered that the systems tested in both electrolytes exhibit a dissolution–deposition reaction mechanism through dissolution–deposition of Mn 2+ ions from/on the cathodes with a display of similar discharge/charge product formation. We have also found that the cell tested using the acetate electrolyte shows evidence of structural irreversibility that might contribute to its rapid capacity degradation. This finding offers an important insight into optimizing the cathode design for enhanced electrochemical function of aqueous Zn/MnO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

All-Inorganic Open-Framework Chalcogenides, A 3 Ga 5 S 9 · x H 2 O ( A = Rb and Cs), Exhibiting Ultrafast Uranyl Remediation and Illustrating a Novel Post-Synthetic Preparation of Open-Framework Oxychalcogenides

Fast and effective uranyl sequestration is of interest to the nuclear industry. Recently layered chalcogenide materials have demonstrated fast, selective, and efficient sorption properties towards uranyl cations and the development and investigation of new types of chalcogenide materials continues to be of interest and represents an intriguing option for uranyl remediation. Three new all-inorganic A 3 Ga 5 S 9 ·xH 2 O (A = Rb, Rb/Cs, and Cs) open-framework chalcogenides were obtained via an in-situ alkali carbonate to alkali sulfide conversion process achieved under mild hydrothermal conditions. The structures of the all-inorganic open framework chalcogenides consist of a 2-fold interpenetrated diamond-like 3D framework containing pseudo-T 3 [Ga 10 S 20 ] 10– supertetrahedra. 48% of the structural volume is occupied by A + cations and water species, as established by single-crystal X-ray diffraction (SCXRD), infrared (IR) and energy-dispersive (EDS) spectroscopies. The dynamic nature of the A + cations and water molecules within the pores was investigated via single crystal X-ray diffraction as well as by IR spectroscopy monitored H 2 O to D 2 O exchange experiments. Framework stability was probed with post-synthetic treatment of A 3 Ga 5 S 9 ·xH 2 O (A = Rb and Cs) samples in acidic solutions that resulted in the formation of the oxysulfide (A/H) 3 Ga 5 S 9–y O y ·xH 2 O (A = Rb and Cs; y = 0–1), as shown by SCXRD and IR. Ion-exchange studies on A 3 Ga 5 S 9 ·xH 2 O (A = Rb and Cs) samples were carried out utilizing a uranyl acetate solution. The presence of the UO 2 2+ species in the ion-exchanged product was supported by IR and EDS spectroscopies. Batch method ion-exchange experiments on Cs 3 Ga 5 S 9 ·xH 2 O powder demonstrated fast kinetics with 95% uranyl removal from the uranyl acetate solution during the first minute, a maximum uranyl uptake capacity of 15mg/g, and the subsequent elution of uranyl species with KCl solution. Furthermore, the porous and dynamic nature of the A 3 Ga 5 S 9 ·xH 2 O framework coupled with effective UO 2 2+ ···S 2– bonding interactions makes it a good potential sorbent for uranyl remediation from aqueous media.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Extreme Ultraviolet and Beyond Extreme Ultraviolet Lithography Using Amorphous Zeolitic Imidazolate Resists Deposited by Atomic/Molecular Layer Deposition

Amorphous zinc-imidazolate (aZnMIm) resists show potential to meet the demands for next-generation high-numerical aperture (high-NA) metal-containing extreme ultraviolet (EUV) resist materials, given their ease of deposition by atomic/molecular layer deposition (ALD/MLD) at thicknesses of 20 nm and below. Here, this study demonstrates that aZnMIm thin films, previously identified as high-resolution electron beam resists, can also function as negative-tone EUV photoresists. Water development achieves high sensitivity (5 mJ/cm 2 ) but leaves significant residue, while acetic acid development results in poor contrast. A hybrid approach─water followed by acetic acid─enables residue-free development with a sensitivity of 181 mJ/cm 2 . Dry development using 1,1,1,5,5,5-hexafluoroacetylacetone (hfacH) is also possible but shows lower sensitivity (375 mJ/cm 2 ) compared to wet development methods. EUV photoelectron spectroscopy (PES), reflectometry/EUV absorption, total electron yield (TEY), residual gas analysis (RGA), and time-of-flight secondary ion mass spectrometry (TOF-SIMS) were used to investigate the effects of EUV irradiation on aZnMIm resists. Reflectometry experiments reveal an aZnMIm EUV absorption coefficient of 6.2 μm –1 , while PES and TEY analyses show that, compared to poly(4-hydroxystyrene) (PHS), a polymer-based reference resist, aZnMIm emits more primary and secondary electrons but generates fewer slow electrons relative to its primary electron emission; its total electron yield is similar to that of poly(methyl methacrylate) (PMMA) resists. When exposed to EUV, aZnMIm predominantly outgasses H 2 , as determined by RGA. TOF-SIMS measurements demonstrate that high-dose EUV exposure only partially fragments the 2-methylimidazole (2MIm) organic linkers, unlike high-dose electron beam exposure, which is known to completely degrade them. Additionally, aZnMIm resists show promise for potential beyond EUV lithography (BEUVL) due to the presence of Zn, which provides higher sensitivity at a wavelength of 6.7 nm compared to other metal ions, such as Sn, that are currently used in the best-performing EUV metal–organic resists. TEY measurements demonstrate that aZnMIm emits nearly twice as many electrons as PHS at 6.7 nm. The BEUV TEY of aZnMIm also surpasses that of PMMA, poly(pentafluorostyrene), and poly(4-iodostyrene), with the latter two being known for their high EUV TEYs. This work provides insight into zeolitic imidazolate framework (ZIF)-based EUV and BEUV resists and highlights their potential for both wet and dry development.

lithography↗
DOE OSTI2020

Ternary Phase Diagram of Water/Bio-Oil/Organic Solvent for Bio-Oil Fractionation

Separating bio-oil by fractionation with different chemical composition is a critical step to refine these oils and obtain high value products. Cold-water precipitation of pyrolytic lignin from bio-oil is the most common approach used. However, the obtained aqueous phase from this method still contain phenols, is diluted and difficult to use. In this study, the use of liquid-liquid extraction with different solvents (1-butanol, ethyl acetate, 1-octanol, dichloromethane, toluene, and hexane) for the separation of targeted molecules (lignin oligomers, sugars, acetic acid) is explored. Ternary phase diagrams for the organic solvent/water/bio-oil are reported. The partition coefficient of compounds of interest (both light and heavy fraction) is reported for the liquid-liquid equilibrium zone. When using butanol as solvent, the highest separation factor of total phenols over total sugars was observed. Furthermore, our results provide information to design L-L separation units with the capacity to selectively recover targeted molecules from pyrolysis oils.

09 BIOMASS FUELS↗
DOE OSTI2020

Flowthrough Pretreatment of Softwood under Water-only and Alkali Conditions

Flowthrough pretreatment provides valuable insight in the fundamentals of deconstruction of plant biomass. In this study, the potential softwood degradation pathways under water-only and alkali conditions were determined by elucidating the deconstructed biomass-derived products at 0-270 °C for 2-10 min at a flow rate of 25 mL/min with water-only or alkaline at initial pH of 8, 9, 11, and 12, respectively. Results indicated that the initial pH value was a convenient indicator along with the severity parameter to control biomass degradation through the non-oxidative (pH<9) and oxidative (pH=9) pathways. Up to 100 % of hemi-sugars, 90 % of cellulose, and 70 % of lignin were derived from softwood under non-oxidative conditions at severity parameter LogR0 around 5.5, respectively. On the contrary, at pH 12, the oxidative degradation resulted in pretreated hydrolysate rich in monomeric and oligomeric phenolic products as well as glycolic acid, acetic acid, and formic acid from carbohydrates. The two dimensional 1H-13C heteronuclear single quantum coherence (HSQC) nuclear magnetic resonance (NMR) analysis revealed that non-oxidative degradation at initial pH values lower than 9 mainly cleaved ß-O-4, all of the ß-ß, and ß-5/a-O-4 linkages, whereas substantial aromatic ring structures with limited ß-O-4 structures remaining at pH 12 through oxidative degradation.

Zhang, Libing↗
DOE OSTI2024

Effect of Adsorbed Carboxylates on the Dissolution of Boehmite Nanoplates in Highly Alkaline Solutions

Understanding the dissolution of boehmite in highly alkaline solutions is important to the processing of the complex nuclear wastes stored at the Hanford (WA) and Savannah River (SC) sites. Here, we report the adsorption of model carboxylate anions on boehmite nanoplates in alkaline solutions and their effects on subsequent boehmite dissolution in 3 M NaOH at 80 °C. Although expectedly lower than at circumneutral pH, adsorption of oxalate at pH 13 at room temperature was significant and remained so through a linear decrease to 3 M NaOH conditions with no evidence for the appearance of new phases. Modeling of the adsorption data and rate were consistent with the formation of outer-sphere surface complexes. By using these conditions to preload the boehmite nanoplates with oxalate, and separately acetate, we measured and compared their dissolution behavior at 80 °C and observed a clear suppression of the dissolution rate for the case of adsorbed oxalate by 23% and for adsorbed acetate by 10% compared to pure solids. Ex situ scanning electron microscopy (SEM) and transmission electron microscopy (TEM) characterization revealed no detectable difference in the morphologic evolution of the dissolving boehmite materials. In conclusion, we nonetheless conclude that pre-adsorbed carboxylate anions, even as nominally weakly bound outer-sphere complexes, can persist on the surface through highly alkaline conditions, decreasing the density of dissolution-active sites and thereby adding an extrinsic control on the dissolution rate.

Adsorption kinetics↗
DOE OSTI2024

Mechanisms of Polyethylene Terephthalate Pellet Fragmentation into Nanoplastics and Assimilable Carbons by Wastewater Comamonas

Comamonadaceae bacteria are enriched on poly(ethylene terephthalate) (PET) microplastics in wastewaters and urban rivers, but the PET-degrading mechanisms remain unclear. Here, we investigated these mechanisms with Comamonas testosteroniKF-1, a wastewater isolate, by combining microscopy, spectroscopy, proteomics, protein modeling, and genetic engineering. Compared to minor dents on PET films, scanning electron microscopy revealed significant fragmentation of PET pellets, resulting in a 3.5-fold increase in the abundance of small nanoparticles (<100 nm) during 30-day cultivation. Infrared spectroscopy captured primarily hydrolytic cleavage in the fragmented pellet particles. Solution analysis further demonstrated double hydrolysis of a PET oligomer, bis(2-hydroxyethyl) terephthalate, to the bioavailable monomer terephthalate. Supplementation with acetate, a common wastewater co-substrate, promoted cell growth and PET fragmentation. Of the multiple hydrolases encoded in the genome, intracellular proteomics detected only one, which was found in both acetate-only and PET-only conditions. Homology modeling of this hydrolase structure illustrated substrate binding analogous to reported PET hydrolases, despite dissimilar sequences. Mutants lacking this hydrolase gene were incapable of PET oligomer hydrolysis and had a 21% decrease in PET fragmentation; re-insertion of the gene restored both functions. Thus, we have identified constitutive production of a key PET-degrading hydrolase in wastewater Comamonas, which could be exploited for plastic bioconversion.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Quantitative DNA Stable Isotope Probing Identifies Active Microorganisms Assimilating Volatile Fatty Acids in Full-Scale Enhanced Biological Phosphorus Removal Processes

Enhanced biological phosphorus removal (EBPR) systems often rely on exogenous carbon sources, such as volatile fatty acids (VFAs), to achieve higher P removal. Here, we employed DNA quantitative stable isotope probing (qSIP) using two VFAs, acetate and propionate, in cyclic anaerobic/aerobic incubations to assess their effects on P cycling and microbial activity with biomass from two full-scale EBPR water resource-recovery facilities that utilize VFA addition. We found that anaerobic VFA uptake preferences differed within known groups of PAOs, such as Candidatus Accumulibacter and Tetrasphaera-affiliated members (e.g., Ca. Phosphoribacter), between the two biomasses. The combination of qSIP with metagenomics identified isotopically labeled phages that were linked to active PAOs, highlighting their potential roles in modulating EBPR community composition and activity. The highest levels of anaerobic labeling from acetate were in genomes belonging to Saccharimonadales and Rickettsiales, which are generally host-associated with bacteria and eukaryotes, respectively. Furthermore, this finding highlights the possibility of cross-feeding between PAO hosts and their parasites or predators, as well as the role of so-far uncharacterized organisms participating in carbon cycling under EBPR conditions. Collectively, these results expand our understanding of the ecological interactions involved in communities anaerobically uptaking VFAs and cycling P that are central to EBPR.

Polyphosphate accumulating organisms↗
DOE OSTI2019

Utilizing Charge Effects and Minimizing Intramolecular Proton Rearrangement to Improve the Overpotential of a Thiosemicarbazonato Zinc HER Catalyst

The zinc(II) complex of diacetyl-2-(4-methyl-3-thiosemicarbazone)-3-(2-hydrazonepyridine), ZnL 1 (1), was prepared and evaluated as a precatalyst for the hydrogen evolution reaction (HER) under homogeneous conditions in acetonitrile. Complex 1 is protonated on the noncoordinating nitrogen of the hydrazonepyridine moiety to yield the active catalyst Zn(HL 1 )OAc (2) upon addition of acetic acid. Addition of methyl iodide to 1 yields the corresponding methylated derivative ZnL 2 I (3). In solution, partial dissociation of the coordinated iodide yields the cationic derivative 3'. Complexes 1–3 were characterized by 1 H NMR, FT-IR, and UV–visible spectroscopies. The solid-state structures of 2 and 3 were determined by single crystal X-ray diffraction. HER studies conducted in acetonitrile with acetic acid as the proton source yield a turnover frequency (TOF) of 7700 s –1 for solutions of 1 at an overpotential of 1.27 V and a TOF of 6700 s –1 for solutions of 3 at an overpotential of 0.56 V. For both complexes, the required potential for catalysis, E cat/2 , is larger than the thermodynamic reduction potential, E 1/2 , indicative of a kinetic barrier attributed to intramolecular proton rearrangement. The effect is larger for solutions of 1 (+440 mV) than for solutions of 3 (+160 mV). Controlled potential coulometry studies were used to determine faradaic efficiencies of 71 and 89% for solutions of 1 and 3, respectively. For both catalysts, extensive cycling of potential under catalytic conditions results in the deposition of a film on the glassy carbon electrode surface that is active as an HER catalyst. Analysis of the film of 3 by X-ray photoelectron spectroscopy indicates the complex remains intact upon deposition. A proposed ligand-centered HER mechanism with 1 as a precatalyst to 2 is supported computationally using density functional theory (DFT). All catalytic intermediates in the mechanism were structurally and energetically characterized with the DFT/B3LYP/6-311g(d,p) in solution phase using a polarizable continuum model (PCM). Finally, the thermodynamic feasibility of the mechanism is supported by calculation of equilibrium constants or reduction potentials for each proposed step.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Modeling the Solvation and Acidity of Carboxylic Acids Using an Ab Initio Deep Neural Network Potential

Formic and acetic acid constitute the simplest of carboxylic acids, yet they exhibit fascinating chemistry in the condensed phase such as proton transfer and dimerization. The go-to method of choice for modeling these rare events have been accurate but expensive ab-initio molecular dynamics simulations. Here, we present a deep neural network potential trained using accurate ab-initio data that can be used in tandem with enhanced-sampling methods to perform an efficient exploration of the free-energy surface of aqueous solutions of weak carboxylic acids. In particular, we show that our model captures proton dissociation and provides a good estimate of the pK a , as well as the dimerization of formic and acetic acid. This provides a suitable starting point for applications in different research areas where computational efficiency coupled with the accuracy of ab-initio methods is required.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Investigation of Complex Intermediates in Solvent-Mediated Synthesis of Thiophosphate Solid-State Electrolytes

Lithium thiophosphates represent a promising class of solid Li + conductors for all-solid-state batteries. Scalable solvent-mediated synthesis routes for several Li–P–S ternary compounds have been reported, but little is known regarding the reaction mechanism of such pathways. This work demonstrates that solvent-mediated synthesis of lithium thiophosphate solid electrolytes from mixtures of Li 2 S and P 2 S 5 proceeds through a highly soluble P 2 S 6 2– intermediate. This intermediate exhibits virtually the same Raman spectra in several solvents including acetonitrile, methyl acetate, ethyl acetate, ethyl propionate, dimethoxyethane, tetraethylene glycol dimethyl ether, and tetrahydrofuran. Additionally, based on this universal intermediate, a general reaction mechanism is proposed for the solvent-mediated synthesis of several lithium thiophosphates including (LiPS 3 ) n , Li 2 P 2 S 6 , Li 7 P 3 S 11 , and Li 3 PS 4 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗