SEARCH · Search NASA

Results for “acoustic tones”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Multiple pure tone noise generation and control.

The generation of multiple pure tones in supersonic fans is discussed. The theoretical results of Kurasaka are reviewed and compared with experimental data obtained on a 36-in. diameter, 1550 ft/sec, 1.6 pressure ratio fan. Detailed measurements on bow shock locations taken with pressure transducers indicate that blade to blade discrepancies are the source of MPT generation. The paper presents some experimental results on an attempt to reduce the shock strength, and subsequently the MPT's, through blade modifications. Other attempts at reducing the MPT's through wall treatment, high inlet flow Mach number, acoustically treated splitters - are discussed. Experimental data is presented on the validity of these noise reduction methods.

Benzakein, M. J.↗

NASA NTRS1993

Preliminary experiments on active control of fan noise from a turbofan engine

In the preliminary experiments reported here, active acoustic sources positioned around the circumference of a turbofan engine were used to control the fan noise radiated forward through the inlet. The main objective was to demonstrate the potential of active techniques to alleviate the noise pollution that will be produced by the next generation of larger engines. A reduction of up to 19 dB in the radiation directivity was demonstrated in a zone that encompasses a 30-deg angle, near the error sensor, while spillover effects were observed toward the lateral direction. The simultaneous control of two tones was also demonstrated using two identical controllers in a parallel control configuration.

Thomas, R. H.↗

NASA NTRS2002

Acoustic Benefits of Stator Sweep and Lean for a High Tip Speed Fan

A model high-speed fan stage was acoustically tested in the NASA Glenn 9- by 15-Foot Low Speed Wind Tunnel at takeoff/approach flight conditions. The fan was designed for a corrected rotor tip speed of 442 m/s (1450 ft/s), and had a powered core, or booster stage, giving the model a nominal bypass ratio of 5. The model also had a simulated engine pylon and nozzle bifurcation contained within the bypass duct. The fan was tested with three stator sets to evaluate acoustic benefits associated with a swept and leaned stator and with a swept integral vane/frame stator which incorporated some of the swept and leaned features as well as eliminated some of the downstream support structure. The baseline fan with the wide chord rotor and baseline stator approximated a current GEAE CF6 engine. A flyover effective perceived noise level (EPNL) code was used to generate relative EPNL values for the various configurations. Flyover effective perceived noise levels (EPNL) were computed from the model data to help project noise benefits. A tone removal study was also performed. The swept and leaned stator showed a 3 EPNdB reduction at lower fan speeds relative to the baseline stator; while the swept integral vane/frame stator showed lowest noise levels at intermediate fan speeds. Removal of the bypass blade passage frequency rotor tone (BPF) showed a 4 EPNdB reduction for the baseline and swept and leaned stators, and a 6 EPNdB reduction for the swept integral vane/ frame stator. Therefore, selective tone removal techniques such as active noise control and/or tuned liner could be particularly effective in reducing noise levels for certain fan speeds.

Woodward, Richard P.↗

NASA NTRS1982

Interior noise considerations for advanced high-speed turboprop aircraft

This paper describes recent research on noise generated by high-speed propellers, on noise transmission through acoustically treated aircraft sidewalls and on subjective response to simulated turboprop noise. Propeller noise discussion focuses on theoretical prediction methods for complex blade shapes designed for low noise at Mach = 0.8 flight and on comparisons with experimental test results. Noise transmission experiments using a 168 cm. diameter aircraft fuselage model and scaled heavy-double-wall treatments indicate that the treatments perform well and that the predictions are usually conservative. Studies of subjective comfort response in an anechoic environment are described for noise signatures having combinations of broadband and propeller-type tone components.

Mixson, J. S.↗

NASA NTRS1993

Effects of signal analysis parameters and noise removal on measured aircraft spectra

Special techniques must be applied when analyzing acoustic noise data from nonstationary sources such as aircraft flyover measurements. Since the Fourier transform is time dependent, the noise signal is divided into short time segments by introducing a window function so that the spectral characteristics remain reasonably stationary. Reducing the window width reduces the frequency resolution while increasing the window duration can lead to spectral smearing. A trade-off must be made between time resolution and frequency resolution. The effects of varying the window duration on narrow-band acoustic spectra and thus the frequency bin width are addressed in this study. The influence of window functions (rectangular, Hamming, etc.) are also investigated. Both a tonal noise source, XV-15 aircraft in the airplane mode, and a broadband noise source, a F-18 aircraft, are considered. When dealing with flight test data, not only is the signal nonstationary, often it is contaminated by both ambient background noise and internal noise generated by the data acquisition system and power generators. Since generator noise is highly tonal, this can be particularly troublesome when computing tone-corrected perceived noise level (PNLT). A scheme is presented in this paper to eliminate unwanted background and internal noise.

Kelly, Jeffrey J.↗

NASA NTRS1984

Laboratory tests on an aircraft fuselage to determine the insertion loss of various acoustic add-on treatments

This paper describes a laboratory study of add-on acoustic treatments for a propeller-driven light aircraft fuselage. The treatments included: no treatment (i.e., baseline fuselage); a production-type double-wall interior; and various amounts of high density fiberglass added to the baseline fuselage. The sound source was a pneumatic-driver with attached exponential horn, supplied with a broadband signal. Data were acquired at the approximate head positions of the six passenger seats. The results were analyzed on space-averaged narrowband, one-third octave band and overall insertion loss basis. In addition, insertion loss results for the different configurations at specific frequencies representing propeller tone spectra are presented. The propeller tone data includes not only the space-averaged insertion loss, but also the variation of insertion loss at these particular frequencies across the six microphone positions.

Heitman, K. E.↗

NASA NTRSDate not supplied

Investigation of the 30P30N Slat Flow Field with Passive Control Devices Using Particle Image Velocimetry

The leading-edge slat of a high-lift wing is one of the main noise contributors during approach and landing. This paper describes an experimental investigation of the velocity field associated with multiple passive noise treatments, including slat-cusp extensions, a cove filler, and a gap filler, on a two-dimensional multi-element high-lift 30P30N airfoil. Previous work documented comparisons of both surface and far field pressure fluctuations in the presence of these devices with those for a baseline case at different flow conditions. However, important information related to the velocity fields was missing from the previous measurements, hindering our ability to elucidate the changes in the flow physics associated with the noise treatments. Therefore, two-component Particle Image Velocity has been used to investigate the influence of passive noise treatments on the flow fields. All measurements are taken at an effective, free-air angle of attack of 5.5 degrees and a stowed-chord-based Reynolds number of 1.71 × 10e6. The measurements show that the slat extensions shorten the slat-cove shear layer trajectory, resulting in reduced growth of disturbances within the slat-cove shear layer. This leads to a shift of tonal peaks to higher frequencies and a reduction in the tonal amplitudes. The gap filler blocks the flow path through the gap, causing the reattachment location to shift to the main wing leading edge lower surface. Consequently, the feedback loop associated with the flow-acoustic interaction in the baseline case is eliminated, and the turbulent kinetic energy in the slat-cove shear layer is significantly reduced. However, extensive flow separation is observed on the suction side of the gap filler, which does not eliminate the noise reduction benefit due to the gap filler, but does degrade the aerodynamic performance of the high-lift configuration. Finally, the overall flow field in the presence of the cove filler is similar to that in the baseline case at the design angle of attack, but the slat-cove shear layer is eliminated leading to a suppression of the cavity tones associated with the shear layer. This change accounts for the reduction in slat noise as measured in previous work.

Aeroacoustics↗

NASA NTRS1975

Effect of entry-lip design on aerodynamics and acoustics of high throat Mach number inlets for the quiet, clean, short-haul experimental engine

Results of scale model tests of high-throat-Mach-number inlets designed to suppress inlet-emitted engine machinery noise produced in a V/STOL wind tunnel are presented. A vacuum system was used to induce inlet airflow with a siren as a noise source. Inlet mass flow was 11.68 kilograms (25.75 lb. min) per second at a throat Mach number of 0.79. The effect of entry-lip design (contraction ratio and diameter ratio) on inlet total-pressure recovery, steady-state pressure distortion, performance at high incidence angles, and noise suppression was determined. With proper entry-lip design, total-pressure recovery in excess of 0.988 could be obtained statically at an average throat Mach number of 0.79. Total-pressure distortion was 5 percent. The reduction in the siren tone sound pressure level transmitted through the inlet was 10 to 14 db relative to that measured at throat Mach 0.6.

Miller, B. A.↗

NASA NTRS1981

Aerodynamic and acoustic behavior of a YF-12 inlet at static conditions

An aeroacoustic test program was performed with a YF-12 aircraft at ground static conditions. The objective was to collect acoustic and aerodynamic data that could determine the cause of YF-12 inlet noise suppression observed earlier. The results showed that the far-field noise level was lower with the YF-12 inlet than with a bellmouth inlet at engine speeds above 5500 rpm. The differences were about 5 PNdB to 11 PNdB, depending on YF-12 inlet configuration and on engine speed. Measurements showed that YF-12 inlet noise suppression was not caused by flow choking. The spike support struts were probably responsible, as in that region the spectral peak near the blade passing frequency disappeared between 6000 and 6600 rpm, and multiple pure tones were greatly reduced.

Bangert, L. H.↗

NASA NTRS1988

Noise of a model counterrotation propeller with reduced aft rotor diameter at simulated takeoff/approach conditions (F7/A3)

A model high-speed advanced counterrotation propeller, F7/A3, was tested in the NASA Lewis Research Center 9 by 15 foot Anechoic Wind Tunnel at simulated takeoff/approach conditions of 0.2 Mach number. Acoustic measurements were taken with an axially translating microphone probe, and with a polar microphone probe which was fixed to the propeller nacelle and could take both sideline and circumferential acoustic surveys. Aerodynamic measurements were also made to establish propeller operating conditions. The propeller was run at two setting angles (front angle/rear angle) of 36.4/43.5 and 41.1/46.4 degrees, forward rotor tip speeds from 165 to 259 m/sec, rotor spacings from 8.48 to 14.99 cm based on pitch change axis separation, and angles of attack to 16 degrees. The aft rotor diameter was 85 percent of the forward rotor diameter to reduce tip vortex-aft rotor interaction as a major interaction noise source. Results are compared with equal diameter F7/A7 data which was previously obtained under similar operating conditions. The aft rotor-alone tone was 7 dB lower for the reduced diameter aft rotor, due to reduced tip speed at constant rpm. Interaction tone levels for the F7/A3 propeller were higher at minimum row spacing and lower at maximum spacing.

Woodward, Richard P.↗

NASA NTRS1988

Noise of a model counterrotation propeller with reduced aft rotor diameter at simulated takeoff/approach conditions (F7/A3)

Woodward, Richard P.↗

NASA NTRS1975

Phase 2 program on ground test of refanned JT8D turbofan engines and nacelles for the 727 airplane. Volume 3: Ground tests

The NASA Refan Program included full-scale performance and noise ground tests of both a current production (JT8D-15) and a refanned (JT8D-115) engine. A description of the two ground tests including detailed propulsion, noise, and structural test results is presented. The primary objectives of the total test program were comparison of JT8D-15 and JT8D-115 overall propulsion system performance and noise characteristics and determination of incremental component noise levels. Other objectives of the test program included: (1) determination of acoustic treatment effectiveness; (2) measurement of internal sound pressure levels; (3) measurement of inlet and exhaust hardware performance; (4) determination of center-engine surge margin; and (5) evaluation of certain structural characteristics associated with the 727 refan center-engine inlet duct and JT8D refan engine exhaust system. The JT8D-15 and -115 tests were conducted during September 1974 and January to March 1975, respectively. Analyses of the test data indicated that the JT8D-115, as compared to the JT8D-15, demonstrates a 12.5 percent to 13.2 percent reduction in static specific fuel consumption, and a reduction of 6 to 7 PNdB in a weighted average value of static tone corrected perceived noise level. Separated into noise components, a significant reduction was shown for the inlet fan, aft fan, exhaust duct flow, turbine, and jet noises. However, core noise was increased. Photographs of test stands and test equipment are shown.

Source record↗

NASA NTRS1973

Noise comparisons from full-scale fan tests at NASA Lewis Research Center.

The overall aero and acoustic design features of eight 6-foot-diameter, single-stage fans tested in an outdoor acoustic facility are described. A correlation of the acoustic results for subsonic tip-speed fans showed the total sound power to be proportional to the mechanical power imparted to the fan and the specific work performed on the air to within plus or minus 2 dB. The correlation was relatively insensitive to fan design variables over a broad range of operating conditions. Maximum perceived noise levels were generally proportional to the sound power levels with both noise levels exhibiting a relatively unique increase with fan pressure ratio when normalized by the delivered thrust. The spectra of broadband noise attributed to the fan exhibited a bimodal characteristic for most of the fans. A predominant mode centered near the blade-passage tone and another at 8 to 16 times the tone frequency.

Heidmann, M. F.↗

NASA NTRS1981

Sound generated in a cascade by three-dimensional disturbances convected in a subsonic flow

Discrete tone sound generation in a subsonic fan subject to three-dimensional disturbances is investigated. The analytical model used treats the fan rotor and stator as linear cascades of thin airfoils in a rectangular duct subject to a three-dimensional gust for which a complete aerodynamic theory already exists. The sound pressure can then be cast as the sum of a finite number of discrete sound waves (modes) the magnitude of which depends on an unknown function satisfying a singular integral equation. Similarity rules are derived to reduce the problem to that of a two-dimensional gust. Three-dimensional effects on the cut-off condition, the sound pressure, and the acoustic power are first investigated for each mode. The theory is then applied to noise generated by typical rotor-wake-defect and rotor-tip-vortex disturbances interacting with a stator.

Atassi, H.↗

NASA NTRS1999

Design of a Low Speed Fan Stage for Noise Suppression

This report describes the design of a low tip speed, moderate pressure rise fan stage for demonstration of noise reduction concepts. The fan rotor is a fixed-pitch configuration delivering a design pressure ratio of 1.378 at a specific flow of 43.1 lbm/sec/sq ft. Four exit stator configurations were provided to demonstrate the effectiveness of circumferential and axial sweep in reducing rotor-stator interaction tone noise. The fan stage design was combined with an axisymmetric inlet, conical convergent nozzle, and nacelle to form a powered fan-nacelle subscale model. This model has a 22-inch cylindrical flow path and employs a rotor with a 0.30 hub-to-tip radius ratio. The design is fully compatible with an existing NASA force balance and rig drive system. The stage aerodynamic and structural design is described in detail. Three-dimensional (3-D) computational fluid dynamics (CFD) tools were used to define optimum airfoil sections for both the rotor and stators. A fan noise predictive system developed by Pratt & Whitney under contract to NASA was used to determine the acoustic characteristics of the various stator configurations. Parameters varied included rotor-to-stator spacing and vane leading edge sweep. The structural analysis of the rotor and stator are described herein. An integral blade and disk configuration was selected for the rotor. Analysis confirmed adequate low cycle fatigue life, vibratory endurance strength, and aeroelastic suitability. A unique load carrying stator arrangement was selected to minimize generation of tonal noise due to sources other than rotor-stator interaction. Analysis of all static structural components demonstrated adequate strength, fatigue life, and vibratory characteristics.

Dalton, W. N.↗

NASA NTRS1994

Resonant Interaction of a Linear Array of Supersonic Rectangular Jets: an Experimental Study

This paper examines a supersonic multi jet interaction problem that we believe is likely to be important for mixing enhancement and noise reduction in supersonic mixer-ejector nozzles. We demonstrate that it is possible to synchronize the screech instability of four rectangular jets by precisely adjusting the inter jet spacing. Our experimental data agrees with a theory that assumes that the phase-locking of adjacent jets occurs through a coupling at the jet lip. Although the synchronization does not change the frequency of the screech tone, its amplitude is augmented by 10 dB. The synchronized multi jets exhibit higher spreading than the unsynchronized jets, with the single jet spreading the least. We compare the nearfield noise of the four jets with synchronized screech to the noise of the sum of four jets operated individually. Our noise measurements reveal that the more rapid mixing of the synchronized multi jets causes the peak jet noise source to move up stream and to radiate noise at larger angles to the flow direction. Based on our results, we believe that screech synchronization is advantageous for noise reduction internal to a mixer-ejector nozzle, since the noise can now be suppressed by a shorter acoustically lined ejector.

Raman, Ganesh↗

NASA NTRS1974

Sound radiation from a high speed axial flow fan due to the inlet turbulence quadrupole interaction

A formula is obtained for the total acoustic power spectra radiated out the front of the fan as a function of frequency. The formula involves the design parameters of the fan as well as the statistical properties of the incident turbulence. Numerical results are calculated for values of the parameters in the range of interest for quiet fans tested at the Lewis Research Center. As in the dipole analysis, when the turbulence correlation lengths become equal to the interblade spacing, the predicted spectra exhibit peaks around the blade passing frequency and its harmonics. There has recently been considerable conjecture about whether the stretching of turbulent eddies as they enter a stationary fan could result in the inlet turbulence being the dominant source of pure tones from nontranslating fans. The results of the current analysis show that, unless the turbulent eddies become quite elongated, this noise source contributes predominantly to the broadband spectrum.

Goldstein, M. E.↗

NASA NTRS1982

A study of resonant-cavity and fiberglass-filled parallel baffles as duct silencers

Acoustical performance and pressure drop were measured for two types of splitters designed to attenuate sound propagating in ducts - resonant-cavity baffles and fiberglass-filled baffles. Arrays of four baffles were evaluated in the 7- by 10-foot wind tunnel number 1 at Ames Research Center at flow speeds from 0 to 41 m/sec. The baffles were 2.1 m high, 305 to 406 mm thick, and 3.1 to 4.4 m long. Emphasis was on measurements of silencer insertion loss as affected by variations of such parameters as baffle length, baffle thickness, perforated skin geometry, cavity size and shape, cavity damping, wind speed, and acoustic field directivity. An analytical method for predicting silencer performance is described and compared with measurements. With the addition of cavity damping in the form of 25-mm foam linings, the insertion loss above 250 Hz of the resonant-cavity baffles was improved 2 to 7 db compared with the undamped baffles; the loss became equal to or greater than the insertion loss of comparable size fiberglass baffles at frequencies above 250 Hz. Variations of cavity size and shape showed that a series of cavities with triangular cross-sections (i.e., variable depth) were superior to cavities with rectangular cross sections (i.e., constant depth). In wind, the undamped, resonant-cavity baffles generated loud cavity-resonance tones; the tones could be eliminated by cavity damping.

Soderman, P. T.↗