Search NASA⌕ Search

SEARCH · Search NASA

Results for “avoidance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Enhancing the Infrared Emission from Silver Chalcogenide Quantum Dots Through Microcavity Coupling

Nanocrystals (NCs) appear as a promising platform for cost effective infrared optoelectronics, while offering a simplified coupling to the CMOS platform. However, this perspective is slowed down by toxicity concerns, the most effective materials being based on Pb and Hg. There is currently a large effort to bring forth new platforms that are active in the infrared with a reduced heavy metal content. Here, in this study, the focus is on silver chalcogenides, which, thanks to a combination of inter‐ and intraband transitions, is suited to cover both short and mid wave infrared ranges. However, this material being less mature, the achieved photoluminescence (PL) appears quite broad, which is problematic for device integration. Here, it is demonstrated that a strong control over the PL spectrum can be obtained through integration into a dielectric cavity that magnifies the electric field by a factor 20 and narrows the PL full width at half maximum down to 15 nm for an emission at telecom wavelength. The PL is also highly directional to avoid most waveguiding effects which is of utmost interest for enhancing the efficiency of NC‐based light emitting diodes.

infrared luminescence↗
DOE OSTI2025

Solution‐Processed Spin‐Polarized Light‐Emitting Diodes of Colloidal Quantum Wells and Magnetic Nanoparticles

Electrical injection of spin-polarized carriers into semiconductors enables circularly-polarized emission from spin-polarized light-emitting diodes (spin-LEDs). The incredible level of tunability of magnetic and electronic properties in colloidal nanocrystals offers unprecedented opportunities for the modulation of polarization of light in solution-processed spin-LEDs based on magnetic nanoparticles unlike epitaxially grown spin-LEDs restricted by a very limited range of materials for their exploitation, and solution-processed spin-LEDs based on chiral molecules, which do not allow the modulation of polarization in general. Here, it is shown that electrical injection of spin-polarized electrons from magnetic Fe 3 O 4 nanoparticles into CdSe/CdZnS core/shell colloidal quantum wells (CQWs) in solution-processed LEDs that allows for polarization modulation of electroluminescence. In this structure, a monolayer of face-down oriented CQWs is deposited as an active layer to avoid polarization losses due to the hopping of the electrons between the CQWs before the radiative recombination process. In this solution-processed spin-LED, the circular polarization reaches 4.5% at 3 K and survives up to 100 K. A net circular polarization is observed at zero magnetic field up to 100 K because of the remnant magnetization of the Fe 3 O 4 nanoparticles. This new colloidal spin-LED architecture presents significant prospects for future solution-processed advanced opto-spintronic devices.

circularly polarized electroluminescence↗
DOE OSTI2024

InAs Terahertz Metalens Emitter for Focused Terahertz Beam Generation

Metasurfaces have opened doors to combining multiple photonic functionalities in a single compact device. In particular, the ability to generate short terahertz (THz) pulses with precise wavefront engineering in a single THz metasurface redefined the role metasurfaces can play in THz systems. Here, an InAs metalens emitter which generates and focuses a THz pulse beam is demonstrated using a 130 nm thick InAs metasurface designed as a binary‐phase Fresnel zone plate. The THz beam is focused to a spot of ≈430 μm at 1 THz with a short focal length of 5 mm and large numerical aperture of 0.5. Nanoscale InAs Mie resonators comprising the metasurface enable THz generation with an amplitude as high as 20 times compared to plasmonic THz emitters and several times compared to a 1 mm thick ZnTe crystal. This InAs metasurface emitter provides a new paradigm for designing THz imaging, spectroscopy, and communication systems, where THz beam generation and shaping are performed with a single device without compromising the generation efficiency, while eliminating losses and avoiding limitations of phase matching of conventional nonlinear optics approaches.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Decarbonization of the Electric Power Sector and Implications for Low-Cost Hydrogen Production from Water Electrolysis

Increasing development of wind and solar generation in the power sector can create economic opportunities for the deployment of water electrolyzers that produce hydrogen. Temporal variation in the marginal cost of energy in future decarbonized grids can make it favorable for electrolyzers to dispatchably ramp hydrogen production up and down in response to low- and high-cost times. Using this strategy, low-cost hydrogen production is enabled by electrolyzers that are low-capital cost and tolerant to frequent on/off cycling. Ramping down hydrogen production to a designated turndown ratio can avoid performance degradation caused by on/off cycling by not shutting the electrolyzer completely off. This comes with a slight cost penalty which can be minimized if the turndown ratio is low (i.e., the system ramps down hydrogen production to close to zero). These results suggest that electrolyzers integrated into future power systems are likely to benefit from the ability to ramp operation up and down quickly and operate in a standby mode. This analysis forms a basis for comparative tradeoffs between electrolyzer capital cost, operating strategy, and system durability and demonstrates the importance of considering all three factors in technoeconomic analysis.

capital cost↗
DOE OSTI2023

Eliminating the Imbalanced Mobility Bottlenecks via Reshaping Internal Potential Distribution in Organic Photovoltaics

The imbalanced carrier mobility remains a bottleneck for performance breakthrough in even those organic solar cells (OSCs) with recorded power conversion efficiencies (PCEs). Herein, a counter electrode doping strategy is proposed to reshape the internal potential distribution, which targets to extract the low mobility carriers at far end. Device simulations reveal that the key of this strategy is to partially dope the active layer with a certain depth, therefore it strengthens the electric field for low mobility carriers near counter electrode region while avoids zeroing the electric field near collection electrode region. Taking advantage of these, PCE enhancements are obtained from 15.4% to 16.2% and from 16.9% to 18.0%, respectively, via cathode p-doping and anode n-doping. Extending its application from opaque to semitransparent devices, the PCE of dilute cell rises from 10.5% to 12.1%, with a high light utilization efficiency (LUE) of 3.5%. The findings provide practical solutions to the core device physical problem in OSCs.

14 SOLAR ENERGY↗
DOE OSTI2023

Organometal Halide Perovskite‐Based Photoelectrochemical Module Systems for Scalable Unassisted Solar Water Splitting

Despite achievements in the remarkable photoelectrochemical (PEC) performance of photoelectrodes based on organometal halide perovskites (OHPs), the scaling up of small-scale OHP-based PEC systems to large-scale systems remains a great challenge for their practical application in solar water splitting. Significant resistive losses and intrinsic defects are major obstacles to the scaling up of OHP-based PEC systems, leading to the PEC performance degradation of large-scale OHP photoelectrodes. Herein, a scalable design of the OHP-based PEC systems by modularization of the optimized OHP photoelectrodes exhibiting a high solar-to-hydrogen conversion efficiency of 10.4% is suggested. As a proof-of-concept, the OHP-based PEC module achieves an optimal PEC performance by avoiding major obstacles in the scaling up of the OHP photoelectrodes. The constructed OHP module is composed of a total of 16 OHP photoelectrodes, and a photocurrent of 11.52 mA is achieved under natural sunlight without external bias. The successful operation of unassisted solar water splitting using the OHP module without external bias can provide insights into the design of scalable OHP-based PEC systems for future practical application and commercialization.

14 SOLAR ENERGY↗
DOE OSTI2021

Quantifying the time‐specific kinetic energy of simulated rainfall using a dynamic rain gauge system

Abstract Raindrop impact derives from the kinetic energy of falling raindrops. Determining the kinetic energy of rainfall requires the size distribution and terminal velocity of raindrops, which necessitates complex instrumentation. To avoid this, empirical relations have been developed that relate rainfall intensity and the rate of kinetic energy, i.e., time‐specific kinetic energy (KE time ). In this study, a dynamic rain gauge system (DRGS) was used to quantify the KE time generated by a rainfall simulator without need of measuring raindrop size distributions or impact velocities. In a series of 10 rainfall tests, the KE time and rainfall intensity were 860.9 (±88.6) J m 2 h −1 and 72.1 (±1.9) mm h −1 , respectively. Estimated KE time was found to agree well with the power‐law relation presented by Petrů and Kalibová for high‐intensity simulated rainfall, which are the conditions when higher deviations occur. The DRGS may be a useful tool in quantifying the KE time of rainfall simulators in hopes to better understand raindrop impact mechanisms.

Wacha, Kenneth M.↗
DOE OSTI2020

Atomic‐Resolution Imaging of Halide Perovskites Using Electron Microscopy

Abstract Atomic‐resolution imaging of halide perovskites (HPs) using transmission electron microscopy (TEM) is challenging because of the sensitivity of their structures to the electron beam. In this article, recent achievements in this area are reviewed, covering both all‐inorganic and organic–inorganic hybrid HPs, with an emphasis on the specific imaging conditions that have proven to be effective in avoiding electron beam‐induced structural damage. The discussion focusses on the total electron dose that HPs can bear before being damaged and the effects of different imaging modes, accelerating voltages, and temperatures. The crucial role of a direct‐detection electron‐counting camera in reducing the required electron dose is outlined, which is indispensable for imaging extremely sensitive organic–inorganic hybrid perovskites. In addition to reviewing published works, the results of initial attempts to perform atomic‐resolution elemental mapping for an all‐inorganic HP and image a hybrid HP using scanning TEM are introduced. The preparation of a TEM specimen from macroscopic crystals or devices of HPs, which is very important for practical applications but has not yet received attention, is also discussed. This article aims to provide guidance on the acquisition of atomic‐resolution TEM images of HPs and inspire the development of more imaging technologies for sensitive materials.

Song, Kepeng↗
DOE OSTI2020

Mixed Ionic–Electronic Conductor of Perovskite Li x La y MO 3-δ toward Carbon-Free Cathode for Reversible Lithium–Air Batteries

Mixed ionic–electronic conductors (MIECs) can play a pivotal role in achieving high energies and power densities in rechargeable batteries owing to their ability to simultaneously conduct ions and electrons. In our study, a new strategy is proposed wherein late 3d transition metals (TMs) are substituted into a perovskite Li-ion conductor to transform it into a Li-containing MIEC. First-principles calculations show that perovskite Li x La y MO 3 with late 3d TMs have a low oxygen vacancy formation energy, implying high electron carrier concentrations corresponding to high electronic conductivity. The activation barriers for Li diffusion in Li x La y MO 3 (M = Ti, Cr, Mn, Fe, and Co) are below 0.411 eV, resulting in high Li-ion conductivity. The designed perovskites of Li0.34La 0.55 MnO 3-δ experimentally prove to have high electronic (2.04 × 10 -3 S cm -1 ) and Li-ion (8.53 × 10 -5 S cm -1 ) conductivities, and when applied in a carbon-free cathode of a Li–air cell, they deliver superior reversibility at 0.21 mAh cm -2 over 100 charge/discharge cycles while avoiding the degradation associated with carbonaceous materials. Finally, this strategy enables the effective design of Li-conducting MIEC and reversible Li–air batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unlocking Failure Mechanisms and Improvement of Practical Li–S Pouch Cells through In Operando Pressure Study

For Lithium-sulfur (Li-S) battery commercialization, the study at a pouch cell level is essential, as some problems ignored or deemed minimal at the smaller level could have a greater effect on the performance of the larger pouch cell. Herein, the failure mechanisms of Li-S pouch cells are deeply investigated via in operando pressure analysis. It is found that highly porous structures of cathodes/separators and slow electrolyte diffusion through cathodes/separators can both lead to poor initial wetting. Additionally, Li-metal anode dominates the thickness variation of the whole pouch cell, which is verified by in situ measured pressure variation. Consequently, a real-time approach that combined normalized pressure with dP/dV analysis is proposed and validated to diagnose the morphology evolution of Li-metal anode. Moreover, applied pressure and porosity/tortuosity ratio of the cathode are both identified as independent factors that influence anode performance. In addition to stabilizing anodes, high pressure is proven to improve the cathode connectivity and avoid cathode cracking over cycling, which improves the possibility of developing cathodes with high sulfur mass loading. Here, this work provides insights into Li-S pouch cell design (e.g., cathode and separator) and highlights pathways to improve cell capacity and cycling performance with applied and monitored pressure.

25 ENERGY STORAGE↗
DOE OSTI2022

Nonradiative Recombination via Charge-Transfer-Exciton to Polaron Energy Transfer Limits Photocurrent in Organic Solar Cells

Here, a recombination and exciton loss mechanism is reported in organic solar cells involving energy transfer between charge transfer (CT) excitons and polarons, impacting photocurrent generation, particularly in the near-infrared where polaronic transitions typically reside. This process sets a low-energy cut-off in the external quantum efficiency spectrum of an excitonic donor/acceptor interface, determined by the low-energy polaron absorption peak and the CT state reorganization energy. Furthermore, this process explains the deviation from unity and bias dependence of the CT state's internal quantum efficiency at low photon energies. This process is demonstrated in a variety of systems and it is hypothesized that CT state to polaron energy transfer recombination may be responsible for a share of nonradiative recombination in all organic photovoltaics and can explain numerous experimentally observed device trends regarding photocurrent generation and energy losses. Overall, this work enhances the understanding of photophysical processes in organic materials and allows the design of systems that can avoid this recombination pathway.

14 SOLAR ENERGY↗
DOE OSTI2023

Role of Scaffold Architecture and Excess Surface Polymer Layers in a 3D-Interconnected Ceramic/Polymer Composite Electrolyte

3D-interconnected ceramic/polymer composite electrolytes offer promise to combine the benefits of both ceramic and polymer electrolytes. However, an in-depth understanding of the role of the ceramic scaffold's architecture, and the associated polymer/ceramic interfaces on the electrochemical properties of such composite electrolytes is still incomplete. Here, these factors are systematically evaluated using an interconnected composite electrolyte with a tunable and well-defined architecture. The ionic conductivity of the ceramic scaffold is strongly dependent on its porosity and tortuosity, as demonstrated experimentally and via theoretical modeling. The connectivity of the ceramic framework avoids the high interfacial impedance at the polymer/ceramic electrolyte interface within the composite. However, this work discovers that the interfacial impedance between the bulk composite and excess surface polymer layers of the composite membrane dominates the overall impedance, resulting in a 1–2 order drop of ionic conductivity compared to the ceramic scaffold. Despite the high impedance interfaces, an improved Li + transference number is found compared to the neat polymer (0.29 vs 0.05), attributed to the ceramic phase's contributions toward ion transport. Further, this leads to flatter overpotentials in lithium symmetric cell cycling. These results are expected to guide future research directions toward scalable manufacturing of composite electrolytes with optimized architecture and interfaces.

25 ENERGY STORAGE↗
DOE OSTI2023

Assessing the Intrinsic Roles of Key Dopant Elements in High–Nickel Layered Oxide Cathodes in Lithium–Based Batteries

A rational compositional design is critical for utilizing LiNiO 2 -based cathodes with Ni contents > 90% as promising next-generation cathode materials. Unfortunately, the lack of a fundamental understanding of the intrinsic roles of key elements, such as cobalt, manganese, and aluminum, makes the rational compositional design of high-Ni cathodes with a limited range of dopants (<10%) particularly challenging. Here, with 5% single-element doped cathodes, viz., LiNi 0.95 Co 0.05 O 2 , LiNi 0.95 Mn 0.05 O 2 , and LiNi 0.95 Al 0.05 O 2 , along with undoped LiNiO 2 (LNO), the influences of the dopants are systematically examined through a control of cutoff charge energy density and a common practice of cutoff charge voltage. Comprehensive investigations into the electrochemical properties, combined with in-depth analyses of the structural and interfasial stabilities and electrolyte decomposition pathways through advanced characterizations, unveil the following: i) the intrinsic role of dopants regulates the cathode energy density or state-of-charge and, more critically, the occurrence of H2–H3 phase transition, which essentially dictates cyclability; ii) undoped LNO can be stabilized well with the avoidance of H2–H3 phase transition; and iii) Co provides more merits overall with an optimized electrochemical operating condition. Finally, this work provides guidance for the compositional design of high-energy-density high-Ni cathodes and sheds light on the challenges of removing Co.

25 ENERGY STORAGE↗
DOE OSTI2023

Accelerated Short Circuiting in Anode-Free Solid-State Batteries Driven by Local Lithium Depletion

“Anode-free” solid-state batteries (SSBs), which have no anode active material, can exhibit extremely high energy density (≈1500 Wh L -1 ). However, there is a lack of understanding of the lithium plating/stripping mechanisms at initially lithium-free solid-state electrolyte (SSE) interfaces because excess lithium metal is often used. Here, it is demonstrated that commercially relevant quantities of lithium (>5 mAh cm -2 ) can be reliably plated at moderate current densities (1 mA cm -2 ) using the sulfide SSE Li 6 PS 5 Cl. Investigations of lithium plating/stripping mechanisms, in conjunction with cryo-ocused ion beam (FIB) imaging, synchrotron tomography, and phase-field modeling, reveal that the cycling stability of these cells is fundamentally limited by the nonuniform presence of lithium during stripping. Local lithium depletion causes isolated lithium regions toward the end of stripping, decreasing electrochemically active area and resulting in high local current densities and void formation. This accelerates subsequent filament growth and short circuiting compared to lithium-excess cells. Despite this degradation mode, here it is shown that anode-free cells exhibit comparable Coulombic efficiency to lithium-excess cells, and improved resistance to short circuiting is achieved by avoiding local lithium depletion through retention of thicker lithium at the interface. These new insights provide a foundation for engineering future high-energy anode-free SSBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Prospective Application, Mechanism, and Deficiency of Lithium Bis(oxalate)Borate as the Electrolyte Additive for Lithium-Batteries

Lithium bis(oxalate)borate (LiBOB) is one of the most common film-forming electrolyte additives used in lithium ion batteries (LIBs), since it can form a dense boron-containing polymer as a solid electrolyte interlayer (or cathode electrolyte interlayer) in order to isolate the electrode material from the electrolyte and prevent side reactions. LiBOB can serve as HF scavenger to maintain the structural integrity of electrodes via avoiding the transition metal dissolution caused by HF attack. Additionally, LiBOB also can react with LiPF 6 to generate lithium difluoro (oxalate)borate (LiDFOB) that can be further used as a clean-up agent for reactive oxygen radicals. This article lists the application of LiBOB in high capacity and high voltage cathode materials, and also reviews the working mechanisms of LiBOB used in these materials to improve the performance of LIBs. Finally, it presents the current shortcomings of LiBOB and strategies to overcome these. This article is expected to provide useful insights for employing LiBOB as a feasible method of dealing with the difficulty of running high capacity LIBs stably under high voltage.

25 ENERGY STORAGE↗
DOE OSTI2023

Interface Design for High‐Performance All‐Solid‐State Lithium Batteries

All‐solid‐state batteries suffer from high interface resistance and lithium dendrite growth leading to low Li plating/stripping Coulombic efficiency (CE) of <90% and low critical current density at high capacity. Here, in this work, both challenges are simultaneously addressed and the Li plating/stripping CE is significantly increased to 99.6% at 0.2 mA cm −2 /0.2 mAh cm −2 , and critical current density (CCD) of > 3.0 mA cm −2 /3.0 mAh cm −2 by inserting a mixed ionic‐electronic conductive (MIEC) and lithiophobic LiF‐C‐Li 3 N‐Bi nanocomposite interlayer between Li 6 PS 5 Cl electrolyte and Li anode. The highly lithiophobic LiF‐C‐Li 3 N‐Bi interlayer with high ionic conductivity (10 −5 S cm −1 ) and low electronic conductivity (3.4×10 −7 S cm −1 ) enables Li to plate on the current collector (CC) surface rather than on Li 6 PS 5 Cl surface avoiding Li 6 PS 5 Cl electrolyte reduction. During initial Li plating on CC, Li penetrates into porous LiF‐C‐Li 3 N‐Bi interlayer and lithiates Bi nanoparticles into Li 3 Bi. The lithiophilic Li 3 Bi and Li 3 N nanoparticles in LiF‐C‐Li 3 N‐Li 3 Bi sub‐interlayer will move to CC along with plated Li, forming LiF‐C/Li 3 N‐Li 3 Bi lithiophobic/lithiophilic sublayer during the following Li stripping. This interlayer enables Co 0.1 Fe 0.9 S 2 /Li 6 PS 5 Cl/Li cell with an areal capacity of 1.4 mAh cm −2 to achieve a cycle life of >850 cycles at 150 mA g −1 . The lithiophobic/lithiophilic interlayer enables solid‐state metal batteries to simultaneously achieve high energy and long cycle life.

25 ENERGY STORAGE↗
DOE OSTI2024

Identifying and Amplifying the Spontaneously Formed Photo‐Charge Contribution in Opaque and Semitransparent Organic Photovoltaics

Abstract Spontaneous photo‐charge (SP) generation within the non‐fullerene (NFA) bulk helps avoid exciton (EX) related loss as compared to the traditional heterojunction route in organic solar cells (OSCs). Unfortunately, the promising SP utilization attracts little attention at this time due to the lack of knowledge on its specific contribution to the photovoltaic performance and rational optimization in high‐efficiency devices. To fill the gap, the NFAs’ SP characteristics are related with their photocurrent loss and power conversion efficiency (PCE) in state‐of‐the‐art materials. Though higher SP population is good for efficient EX utilization, it simultaneously acts as an additional photo‐charge recombination channel. The former can be further enhanced by increasing the NFAs’ crystallinity with preferred lamellar growth, and the latter can be suppressed via electric doping. With the aid of the two‐step optimization strategy, the total photocurrent loss is reduced from 14.4% to 4.8%, accompanying with PCE increment from 16.9% to 18.5%. The SP utilization strategy is finally applied in the semitransparent OSCs (ST‐OSCs), due to its less heterojunction area sensitive photo‐charge generation characteristic. A light utilization efficiency (LUE) is then increased from 3.21% to 3.77%. The findings highlight the pursue of efficient SP utilization as a new design philosophy in future OSCs’ progresses.

Chemistry↗