Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Cold crucible induction melter studies for making glass ceramic waste forms: A feasibility assessment

Glass ceramics are being developed to immobilize fission products, separated from used nuclear fuel by aqueous reprocessing, into a stable waste form suitable for disposal in a geological repository. This work documents the glass ceramic formulation at bench scale and for a scaled melter test performed in a pilot-scale (approximately 1/4 scale) cold crucible induction melter (CCIM). Melt viscosity, electrical conductivity, and crystallization behavior upon cooling were measured on a small set of compositions to select a formulation for melter testing. Property measurements also identified a temperature range for melter operation and cooling profiles necessary to crystallize the targeted phases in the waste form. Bench scale and melter run results successfully demonstrate the processability of the glass ceramic using the CCIM melter technology.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

I-NERI Annual Technical Progress Report 2007-004-K Development and Characterization of New High-Level Waste Forms for Achieving Waste Minimization from Pyroprocessing

The current method for the immobilization of fission products that accumulate in electrorefiner salt during the electrochemical processing of used metallic nuclear fuel is to encapsulate the electrorefiner salt in a glass-bonded sodalite ceramic waste form. This process was developed by Argonne National Laboratory in the USA and is currently performed at the Idaho National Laboratory for the treatment of Experimental Breeder Reactor-II (EBR-II) used fuel. This process utilizes a “once-through” option for the disposal of spent electrorefiner salt; where, after the treatment of the EBR-II fuel, the electrorefiner salt containing the active fission products will be disposed of in the ceramic waste form (CWF). The CWF produced will have low fission product loading of approximately 2 to 5 weight percent due to the limited fuel inventory currently being processed. However; the design and implementation of advanced electrochemical processing facilities to treat used fuel would process much greater quantities fuel. With an advanced processing facility, it would be necessary to selectively remove fission products from the electrorefiner salt for salt recycle and to concentrate the fission products to reduce the volume of high-level waste from the treatment facility. The Korean Atomic Energy Research Institute and the Idaho National Laboratory have been collaborating on I-NERI research projects for a number of years to investigate both aspects of selective fission product separation from electrorefiner salt, and to develop advanced waste forms for the immobilization of the collected fission products. The first joint KAERI/INL I-NERI project titled: 2006-002-K, Separation of Fission Products from Molten LiCl-KCl Salt Used for Electrorefining of Metal Fuels, was successfully completed in 2009 by concentrating and isolating fission products from actual electrorefiner salt used for the treated used EBR-II fuel. Two separation methods were tested and from these tests were produced concentrated salt products that acted as the feed material for development of advanced waste forms investigated in this proposal. Accomplishments from the first year activities associated with this I-NERI project included the down selection of candidate waste forms to immobilize fission products separated from electrorefiner salt, and the design of equipment to fabricate actual waste forms in the Hot Fuels Examination Facility (HFEF) at the INL. Reported in this document are accomplishments from the second year (FY10) work performed at the INL, and includes the testing of waste form fabrication equipment, repeating the fission product precipitation experiment, and initial waste form fabrication efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tuning crosslinking of hybrid preceramic polymers in vat photopolymerization toward controlled ceramic yields

Control of preceramic polymer crosslinking for UV-curable processing is essential for fine 3D printing with high ceramic conversion for sustainable polymer-derived ceramics (PDC) engineering. While various factors influencing ceramic yield have been studied, the systematic exploration of the relationship between crosslinking and ceramic yield, especially when crosslinking increases volatile elements, remains open for further investigation. This study addresses this gap by utilizing vat photopolymerization (VP) additive manufacturing (AM) as a versatile platform for controlling preceramic crosslinking and ceramic yield. By rationally designing and tuning the photochemical crosslinking through digital light processing (DLP), we demonstrate that the ceramic yield can be enhanced from 64% to over 86%, even with added volatile elements. We reveal that the post-pyrolysis ceramic yield can be closely correlated with the pre-pyrolysis crosslinking of the preceramic network represented by its stiffness. This correlation thereby suggests a fast, energy-efficient, non-destructive methodology to predict and improve ceramic yield. Combined with these findings, our one-pot thiol-ene hybridization of polycarbosilane and polycarbosiloxane via DLP offers an exemplary method to generate hybrid preceramic polymers with tailored material properties toward target applications, and potentially even higher ceramic yields. This study thus contributes to achieving better resource- and energy-efficient preceramic polymer and PDC processing routes toward sustainable, advanced organic–inorganic materials manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Micro Electro Discharge Machining of Electrically Nonconductive Ceramics

EDM is a known process for machining of hard and brittle materials. Due to its noncontact and nearly forceless behaviour, it has been introduced into micro manufacturing and through constant development it is now an important means for producing high-precision micro geometries. One restriction of EDM is its limitation to electrically conducting materials.Today many applications, especially in the biomedical field, make use of the benefits of ceramic materials, such as high strength, very low wear and biocompatibility. Common ceramic materials such as Zirconium dioxide are, due to their hardness in the sintered state, difficult to machine with conventional cutting techniques. A demand for the introduction of EDM to these materials could so far not be satisfied because of their nonconductive nature.At the Chemnitz University of Technology and the Fraunhofer IWU, investigations in the applicability of micro-EDM for the machining of nonconductive ceramics are being conducted. Tests are undertaken using micro-EDM drilling with Tungsten carbide tool electrodes and ZrO{sub 2} ceramic workpieces. A starting layer, in literature often referred to as 'assisting electrode' is used to set up a closed electric circuit to start the EDM process. Combining carbon hydride based dielectric and a specially designed low-frequency vibration setup to excite the workpiece, the process environment can be held within parameters to allow for a constant EDM process even after the starting layer is machined. In the experiments a cylindrical 120 {mu}m diameter Tungsten carbide tool electrode and Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} worpieces are used. The current and voltage signals of the discharges within the different stages of the process (machining of the starting layer, machining of the base material, transition stage) are recorded and their characteristics compared to discharges in metallic material. Additionally, the electrode feed is monitored. The influences of the process parameters are analysed with regard to the discharge type, electrode wear and process speed.Using the found parameters, micro geometries can be successfully machined into nonconductive Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} ceramic by means of micro-EDM.

36 MATERIALS SCIENCE↗

More About Plasma-Spraying Ceramics Onto Smooth Metals

Paper presents additional information on fabrication process described in "Plasma-Spraying Ceramics Onto Smooth Metallic Substrates" (LEW-15164). Provides additional information on specific substrate materials advantageously coated in two-stage plasma-spraying process.

Miller, Robert A.↗

Synthesis and characterization of chloro-sulphide glass-ceramics containing neodymium(III) ions

In this paper, we describe the preparation of Nd{sup 3+} doped glass-ceramics in the (GeS{sub 2}){sub 70}-(Ga{sub 2}S{sub 3}){sub 20}-(CsCl){sub 10} system. Neodymium has been introduced as metallic powder or incorporated as sulphide. Appropriate heat treatments of the base-glass lead to glass-ceramics with controllable crystal sizes that are transparent in the visible and infrared spectral ranges. X-ray diffraction as well as electron diffraction techniques were used to investigate the crystallization process. Differential scanning calorimetry indicates that neodymium ions are poor nucleating agents in this glass compared to erbium ions. Luminescence measurements were also performed and point out that although the ceramization process increases significantly the luminescence efficiency, the neodymium ions are only partially incorporated in the nanocrystals.

36 MATERIALS SCIENCE↗

Potential of Materials to Impact Megawatt-Scale Electric Machines

High specific power density, megawatt-scale electric machines (motors and generators) are needed to enable megawatt-scale electric aircraft propulsion systems for single isle aircraft. Thermally insulating electrical insulation materials in the stator windings limits the ability to thermally manage the heat produced in these machines. Polymer-ceramic composites along with novel processing techniques offer viable options to improve the thermal conductivity of the electrical insulation system. This paper outlines current National Aeronautics and Space Administration’s Glenn Research Center efforts of developing several polymer-ceramic systems and processing techniques as they relate to electric machine insulation (including potting). There is also analysis of how these factors relate to machine performance.

electric macnhine↗

Processing and Material Characterization of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics.

The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures up to 260C. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in the composites. In this study, continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. The oxyacetylene torch testing and three point bend testing have been performed on test panels and the test results are presented.

Polymer Derived Ceramics↗

Development of a sintering process for recycling oil shale fly ash and municipal solid waste incineration bottom ash into glass ceramic composite

Highlights: • Glass ceramic composite is prepared from oil shale fly ash and MSWI bottom ash. • A novel method for the production of glass ceramic composite is presented. • It provides simple route and lower energy consumption in terms of recycling waste. • The vitrified slag can promote the sintering densification process of glass ceramic. • The performances of products decrease with the increase of oil shale fly ash content. - Abstract: Oil shale fly ash and municipal solid waste incineration bottom ash are industrial and municipal by-products that require further treatment before disposal to avoid polluting the environment. In the study, they were mixed and vitrified into the slag by the melt-quench process. The obtained vitrified slag was then mixed with various percentages of oil shale fly ash and converted into glass ceramic composites by the subsequent sintering process. Differential thermal analysis was used to study the thermal characteristics and determine the sintering temperatures. X-ray diffraction analysis was used to analyze the crystalline phase compositions. Sintering shrinkage, weight loss on ignition, density and compressive strength were tested to determine the optimum preparation condition and study the co-sintering mechanism of vitrified amorphous slag and oil shale fly ash. The results showed the product performances increased with the increase of sintering temperatures and the proportion of vitrified slag to oil shale fly ash. Glass ceramic composite (vitrified slag content of 80%, oil shale fly ash content of 20%, sintering temperature of 1000 °C and sintering time of 2 h) showed the properties of density of 1.92 ± 0.05 g/cm{sup 3}, weight loss on ignition of 6.14 ± 0.18%, sintering shrinkage of 22.06 ± 0.6% and compressive strength of 67 ± 14 MPa. The results indicated that it was a comparable waste-based material compared to previous researches. In particular, the energy consumption in the production process was reduced compared to conventional vitrification and sintering method. Chemical resistance and heavy metals leaching results of glass ceramic composites further confirmed the possibility of its engineering applications.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Corrosion of Silicon-Based Ceramics in Combustion Environments

The processes of passive oxidation, deposit-induced corrosion, active oxidation, scale/substance interactions, and scale volatility are presently studied in the case of high-purity SiC and Si3N4 in pure oxygen, giving attention to such secondary elements in the ceramics as water and CO2 oxidants, combustion environment impurities, and thermal cycling. Deposit-induced corrosion is discussed for the cases of NaSO4 as well as vanadate and oxide-slag deposits; issues associated with the active-to-passive oxidation transition are noted.

Jacobson, Nathan S.↗

Status of NASA space-processing research

A survey is presented of the history, goals, objectives, and implementation of the NASA space processing program. Program activities have resulted in the present division of interests into metallurgical processes, electronic materials, biological applications, ceramics and glass, physical properties in fluids, and chemical processes. An outline is given of space shuttle payload development.

Bredt, J. H.↗

Floating the Ball: Advances in the Technology of Electrostatic Levitation

Electrostatic Levitation (ESL) is an emerging technology. The MSFC ESL is a NASA facility that supports investigations of refractory solids and melts. The facility can be used to process a wide variety of materials including metals, alloys, ceramics, glasses and semiconductors. Containerless processing via ESL provides a high-purity environment for the study of high temperature materials and access to metastable states. Scientific topics investigated in the facility include nucleation, undercooling, metastable state formation and metallic glass formation. Additionally, the MSFC ESL provides data for the determination of phase diagrams, time-temperature-transition diagrams, viscosity, surface tension, density, heat capacity and creep resistance. In order to support a diverse research community, the MSFC ESL facility has developed a number of technical capabilities, including a portable system for in situ studies of structural tran$hrmations during processing at the high-energy X-ray beamline at the Advanced Photon Source of Argonne National Laboratory. The capabilities of the MSFC ESL facilities will be discussed and selected results of materials processing and characterization studies will be presented.

Rogers, Jan R.↗

Marshall Space Flight Center Materials and Processes Laboratory

Marshall?s Materials and Processes Laboratory has been a core capability for NASA for over fifty years. MSFC has a proven heritage and recognized expertise in materials and manufacturing that are essential to enable and sustain space exploration. Marshall provides a "systems-wise" capability for applied research, flight hardware development, and sustaining engineering. Our history of leadership and achievements in materials, manufacturing, and flight experiments includes Apollo, Skylab, Mir, Spacelab, Shuttle (Space Shuttle Main Engine, External Tank, Reusable Solid Rocket Motor, and Solid Rocket Booster), Hubble, Chandra, and the International Space Station. MSFC?s National Center for Advanced Manufacturing, NCAM, facilitates major M&P advanced manufacturing partnership activities with academia, industry and other local, state and federal government agencies. The Materials and Processes Laborato ry has principal competencies in metals, composites, ceramics, additive manufacturing, materials and process modeling and simulation, space environmental effects, non-destructive evaluation, and fracture and failure analysis provide products ranging from materials research in space to fully integrated solutions for large complex systems challenges. Marshall?s materials research, development and manufacturing capabilities assure that NASA and National missions have access to cutting-edge, cost-effective engineering design and production options that are frugal in using design margins and are verified as safe and reliable. These are all critical factors in both future mission success and affordability.

Tramel, Terri L.↗

Process for fabrication of cermets

Cermet comprising ceramic and metal components and a molten metal infiltration method and process for fabrication thereof. The light weight cermets having improved porosity, strength, durability, toughness, elasticity fabricated from presintered ceramic powder infiltrated with a molten metal or metal alloy. Alumina titanium cermets biocompatible with the human body suitable for bone and joint replacements.

36 MATERIALS SCIENCE↗

Solid Freeform Fabrication of Continuous Fiber Reinforced Composites for Propulsion Applications

For propulsion related applications, materials must be able to demonstrate excellent ablation and oxidation resistance at temperature approaching 3500'C, adequate load bearing capabilities, non-catastrophic failure modes, and ability to withstand transient thermal shock. A potential list of propulsion-material property requirements includes, low density, high elastic modulus, low thermal-expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. In many cases, they will also need to be able to be joined, survive thermal cycling and multi-axial stress states, and for reusable applications, the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attribute for these materials are the need to be lower cost and readily available in large quantities. Recently, Advanced Ceramics Research, Inc. (ACR) has developed low cost, flexible- manufacturing processes for Zr & Hf-based carbon fiber reinforced composites, materials with good oxidation and ablation resistance up to 3500 C. This process, called Continuous Composite Co-extrusion (C(sup 3)), incorporates carbon fibers to fabricate 'in-situ' carbide and boride-matrix/carbon fiber composites. This is a variation of ACR's manufacturing process for low-cost structural ceramic materials called Fibrous Monoliths With carbon fiber reinforcements. Fibrous Monolithic materials have a distinct fibrous texture, consist of intertwined cells of a primary phase, separated by cell boundaries of a tailored secondary phase and show very high fracture energies, damage tolerance, and graceful failure. Since they are monolithic powder based composites-, they can be manufactured by conventional powder processing techniques using inexpensive raw materials. This combination of high performance and low cost is a breakthrough that could enable wider application of ceramics in high temperature applications. Typical volume fractions of the two phases are 80 to 95% for the cell phase and 5 to 20% for the interpenetrating cell boundary phase. ACR is currently developing an innovative solid freeform form fabrication (SFF) approach to produce Hf and Zr based ceramic composite components reinforced with continuous carbon fiber tows for critical structural components such as tubes and blisks. The process is simple, robust and will be widely applicable to a number of material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The current process is being developed in collaboration with UD-CCM. The paper will detail the freeform fabrication process to create low-cost ceramic fiber reinforced composites for high-temperature applications. The results of mechanical properties and microstructural characterization will be presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts for propulsion applications at an order of magnitude lower cost than current CVI and PIP process.

Vaidyanathan, R.↗

Improved high temperature radiation damage tolerance in a three-phase ceramic with heterointerfaces

Abstract Radiation damage tolerance for a variety of ceramics at high temperatures depends on the material’s resistance to nucleation and growth of extended defects. Such processes are prevalent in ceramics employed for space, nuclear fission/fusion and nuclear waste environments. This report shows that random heterointerfaces in materials with sub-micron grains can act as highly efficient sinks for point defects compared to grain boundaries in single-phase materials. The concentration of dislocation loops in a radiation damage-prone phase (Al 2 O 3 ) is significantly reduced when Al 2 O 3 is a component of a composite system as opposed to a single-phase system. These results present a novel method for designing exceptionally radiation damage tolerant ceramics at high temperatures with a stable grain size, without requiring extensive interfacial engineering or production of nanocrystalline materials.

36 MATERIALS SCIENCE↗