Search NASA⌕ Search

SEARCH · Search NASA

Results for “climbing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗
NASA NTRS1989

Importance of engine as a source of helicopter external noise

A turboshaft engine's importance as a source of helicopter external noise is presently evaluated experimentally and analytically on the basis of test data from an MD500E helicopter, with and without engine muffler, during level flyovers and climbing flight. A strong engine noise component is noted for helicopter positions nearly overhead and beyond observed position, especially in the 200-1000 Hz range; its strong rearward directivity suggests the noise source to be the broadband exhaust or combustion noise radiated from the exhaust duct. The engine muffler furnished estimated perceived noise level reductions of 2-3 dB for the centerline.

Janakiram, R. D.↗
NASA NTRS1989

Experimental investigation of the high angle of attack characteristics of a high performance general aviation aircraft

Scale model wind tunnel tests and full scale flight tests have been conducted for the Questair Venture general aviation aircraft configuration in order to investigate its high angle-of-attack aerodynamics. Attention is given to the formulation of a wing leading-edge modification capable of enhancing stall departure characteristics. This modification, which involved both outboard wing leading-edge droop and two chordwise leading-edge slots, is found to produce almost no wing-rock tendency when tested on a wind tunnel free-to-roll apparatus; in the full-scale aircraft, the modification yielded gentle, controllable stall characteristics with little cruise and climb performance penalty.

Meyer, H. F.↗
NASA NTRS1990

Articulated Suspension Without Springs

Wheels negotiate bumps and holes with minimal tilting of vehicle body. In new suspension, wheel climbs obstacle as high as 1 1/2 times its diameter without excessive tilting of chassis. Provides highly stable ride over rough ground for such vehicles as wheelchairs, military scout cars, and police and fire robots. System of levers distributes weight to wheels. Sized to distribute equal or other desired portions of load among wheels.

Bickler, Donald B.↗
NASA NTRS1990

Agile Walking Robot

Proposed agile walking robot operates over rocky, sandy, and sloping terrain. Offers stability and climbing ability superior to other conceptual mobile robots. Equipped with six articulated legs like those of insect, continually feels ground under leg before applying weight to it. If leg sensed unexpected object or failed to make contact with ground at expected point, seeks alternative position within radius of 20 cm. Failing that, robot halts, examines area around foot in detail with laser ranging imager, and replans entire cycle of steps for all legs before proceeding.

Larimer, Stanley J.↗
NASA NTRS1990

Rolling Robot

Proposed rolling robot routinely traverses rough terrain, clearing rocks as high as 1 m. Climbs steps 1 m high and spans ditches 2.3 m wide. Simple but rugged semiautonomous rover has large wheels and articulated body. With combined yaw, roll, and four-wheel drive, robot crawls slowly to pass over soft or sandy terrain. Senses terrain along corridor, chooses path to avoid insurmountable obstacles, and monitors state of vehicle for unexpected hazards.

Larimer, Stanley J.↗
NASA NTRS1989

The 10.7-cm microwave observations of AR 5395 and related terrestrial effects

The 10.7 cm flux patrols in Canada recorded 4 Great Bursts (peaks greater than 500 sfu) during the disk passage of AR 5395 in March 1989. The Great Bursts of 16 and 17 March were simple events of great amplitude and with half-life durations of only several minutes. Earlier Great Bursts, originating on 6 March towards the NE limb and on 10 March closer to the central meridian, belong to an entirely different category of event. Each started with a very strong impulsive event lasting just minutes. After an initial recovery, however, the emission climbed back to level as greater or greater than the initial impulsive burst. The events of 6 and 10 March stayed above the Great Burst threshold for at least 100 minutes. The second component of long duration in these cases is associated with Type 4 continuum emission and thus very likely with CMEs. Major geomagnetic disturbances did not occur as a result of the massive complex event of 6 March or the two simple but strong events of 16 and 17 March. But some 55 hours after the peak in the long-enduring burst of 10 March, a storm began which qualifies as the fourth strongest geomagnetic storm in Canada since 1932. The vertical component of the earth's field measured during the storm by a fluxgate magnetometer at a station in Manitoba is presented. Within a minute of the sudden commencement of this storm, a series of breakdowns began in the transmission system of Hydro-Quebec which resulted in a total loss of power, on a bitterly cold winter's day, for at least 10 hours. The loss of power provoked an enormous outcry from the public resulting in the power utilities being more receptive to the need to monitor solar as well as geomagnetic activity.

Gaizauskas, V.↗
NASA NTRS1989

An in-flight technique for wind measurement in support of the space shuttle program

A technique to use an aircraft to measure wind profiles in the altitude range of 1,500 to 18,200 m was demonstrated at NASA Ames-Dryden. This demonstration was initiated to determine if an aircraft could measure wind profiles in support of space shuttle launches. The Jimsphere balloon is currently the device used to measure pre-launch wind profiles for the space shuttle. However, it takes approximately an hour for the Jimsphere to travel through the altitudes of interest. If these wind instruments could be taken with an aircraft closer to launch in a more timely manner and with the same accuracy as a Jimsphere balloon, some uncertainties in the measurements could be removed. The aircraft used for this investigation was an F-104G which is capable of flight above 18,000 m. It had conventional research instrumentation to provide air data and flow angles along with a ring laser gyro inertial navigation system (INS) to provide inertial and Euler angle data. During the course of 17 flights, wind profiles were measured in 21 climbs and 18 descents. Preliminary comparisons between aircraft measured wind profiles and Jimsphere measured profiles show reasonable agreement (within 3 m/sec). Most large differences between the profiles can usually be explained by large spatial or time differences between the Jimsphere and aircraft measurements, the fact that the aircraft is not in a wings-level attitude, or INS shifts caused by aircraft maneuvering.

Bjarke, Lisa J.↗
NASA NTRS1990

Total cross sections for positrons scattered elastically from helium based on new measurements of total ionization cross sections

An improved technique is presented for employing the 2.3m spectrometer to measure total ionization cross sections, Q sub ion, for positrons incident on He. The new ionization cross section agree with the values reported earlier. Estimates are also presented of total elastic scattering cross section, Q sub el, obtained by subtracting from total scattering cross sections, Q sub tot, reported in the literature, the Q sub ion and Q sub Ps (total positronium formation cross sections) and total excitation cross sections, Q sub ex, published by another researcher. The Q sub ion and Q sub el measured with the 3m high resolution time-of-flight spectrometer for 54.9eV positrons are in accord with the results from the 2.3m spectrometer. The ionization cross sections are in fair agreement with theory tending for the most part to be higher, especially at 76.3 and 88.5eV. The elastic cross section agree quite well with theory to the vicinity of 50eV, but at 60eV and above the experimental elastic cross sections climb to and remain at about 0.30 pi a sub o sq while the theoretical values steadily decrease.

Diana, L. M.↗
NASA NTRS1989

Airplane takeoff and landing performance monitoring system

The invention is a real-time takeoff and landing performance monitoring system which provides the pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V sub R) within the safe zone of the runway or stopping the aircraft on the runway after landing or take off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. An important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in headwind occurring as the takeoff roll progresses. The system displays the position of the airplane on the runway, indicating runway used and runway available, summarizes the critical information into a situation advisory flag, flags engine failures and off-nominal acceleration performance, and indicates where on the runway particular events such as decision speed (V sub 1), rotation speed (V sub R) and expected stop points will occur based on actual or predicted performance. The display also indicates airspeed, wind vector, engine pressure ratios, second segment climb speed, and balanced field length (BFL). The system detects performance deficiencies by comparing the airplane's present performance with a predicted nominal performance based upon the given conditions.

Middleton, David B.↗
NASA NTRS1990

Flight test investigation of certification issues pertaining to general-aviation-type aircraft with natural laminar flow

Development of Natural Laminar Flow (NLF) technology for application to general aviation-type aircraft has raised some question as to the adequacy of FAR Part 23 for certification of aircraft with significant NLF. A series of flight tests were conducted with a modified Cessna T210R to allow quantitative comparison of the aircraft's ability to meet certification requirements with significant NLF and with boundary layer transition fixed near the leading edge. There were no significant differences between the two conditions except an increasing in drag, which resulted in longer takeoff distances and reduced climb performance.

Doty, Wayne A.↗
NASA NTRS1990

Feasibility study for a microwave-powered ozone sniffer aircraft

The preliminary design of a high-altitude, remotely-piloted, atmospheric-sampling aircraft powered by microwave energy beamed from ground-based antenna was completed. The vehicle has a gross weight of 6720 pounds and is sized to carry a 1000 pound payload at an altitude of 100,000 feet. The underside of the wing serves as the surface of a rectenna designed to receive microwave energy at a power density of 700 watts per square meter and the wing has a planform area of 3634 square feet to absorb the required power at an optimum Mach number M = 0.44. The aircraft utilizes a horizontal tail and a canard for longitudinal control and to enhance the structural rigidity of the twin fuselage configuration. The wing structure is designed to withstand a gust-induced load factor n = 3 at cruise altitude but the low-wing loading of the aircraft makes it very sensitive to gusts at low altitudes, which may induce load factors in excess of 20. A structural load alleviation system is therefore proposed to limit actual loads to the designed structural limit. Losses will require transmitted power on the order of megawatts to be radiated to the aircraft from the ground station, presenting environmental problems. Since the transmitting antenna would have a diameter of several hundred feet, it would not be readily transportable, so we propose that a single antenna be constructed at a site from which the aircraft is flown. The aircraft would be towed aloft to an initial altitude at which the microwave power would be utilized. The aircraft would climb to cruise altitude in a spiral flight path and orbit the transmitter in a gentle turn.

Botros, David F.↗
NASA NTRS1990

Proposed definition of the term en route in en route aircraft noise

The problem of en route aircraft noise was examined in a formal, dedicated, setting. Whereas the general meaning of the term en route might be intuitively understood, it is suggested that a precise formal definition of the term en route would be opportune from the outset, especially since the scientific and technical investigation of the problem of noise immissions on the ground from aircraft in flight away from the airspace of an airport may conceivably lead to administrative, regulatory, and legal consequences that would mandatorily require a precise definition of the term en route. Five flight segments, with their differing airframe configurations, engine thrusts, and airspeed management, should form the basis for the differential consideration of the noise immissions perceived on the ground underneath or near the defined segments of the flightpath in en route flight, from the end of the initial climb from an airport after takeoff until the final approach to an airport.

Garbell, Maurice A.↗
NASA NTRS1990

Sound propagation elements in evaluation of en route noise of advanced turbofan aircraft

Cruise noise from an advanced turboprop aircraft is reviewed on the basis of available wind tunnel data to estimate the aircraft noise signature at the source. Available analytical models are used to evaluate the sound levels at the ground. The analysis allows reasonable estimates to be made of the community noise levels that might be generated during cruise by such aircraft, provides the basis for preliminary comparisons with available data on noise of existing aircraft during climb and helps to identify the dominant elements of the sound propagation models applicable to this situation.

Sutherland, Louis C.↗
NASA NTRS1990

The effect of noise-abatement profiles on noise immissions and human annoyance underneath a subsequent climbpath

En route noise emissions on the ground can be affected by the detailed characteristics of intended noise-abatement climb profiles and procedures to an extent of 10 or more nautical miles from the start of the takeoff roll of a large or heavy air-carrier-type aircraft. Suggestions submitted to the noise abatement officials of the airports at Frankfurt, Federal Republic of Germany, and Zurick, Switzerland, and the aircarriers Lufthansa German Airlines and SWISSAIR are explained and discussed.

Garbell, Maurice A.↗
NASA NTRS1990

Additive evaluation criteria for aircraft noise

The occurrence of unexpected aircraft noise events will frequently evoke intense complaints about annoyance over such events. It is recognized that the relationship between the volume of complaints and the corresponding maximum noise levels does in fact depend on the circumstances of the complainants and the time of year. The frequency of occurrence of the respective noise events is also a factor. The possible practical value of the addition of the maximal noise level, to the well-known cumulative noise descriptors L(sub eq), L(sub dn), etc. may be considered. One might start by considering the difference between the L(sub eq) and the average maximal noise level of the twenty loudest single noise events on an average day. A somewhat less sharply focused consideration of the maximum noise levels was adopted. In that standard the scope of noise-mitigation measures is defined generally with reference to L(sub eq). If the average maximal noise level L(sub max) of the entire aircraft fleet mix exceeds the L(sub eq) by more than 20 dB(A) and if more than 20 daily aircraft noise events exceed the L(sub eq) than the difference L(sub max)-20 becomes the key criterion for noise-mitigation measures. A statistical correlation of a large number of data from aircraft-noise-monitoring sensors located both directly underneath and laterally disposed to an aircraft flight-path has supplied a basis for the determination of the distribution of the maximal noise levels about the average value, L(sub max), of each type of aircraft. This distribution is given for the takeoff climb and for the landing approach.

Meyer, Thomas J.↗
NASA NTRS1990

Project Dawdler: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

In direct response to Request for Proposals: Flight at very low Reynolds numbers - a station keeping mission, the members of Design Squad E present Project Dawdler: a remotely-piloted airplane supported by an independently controlled take-off cart. A brief introduction to Project Dawdler's overall mission and design, is given. The Dawdler is a remotely-piloted airplane designed to fly in an environmentally-controlled closed course at a Reynolds number of 10(exp 5) and at a cruise velocity of 25 ft/s. The two primary goals were to minimize the flight Reynolds number and to maximize the loiter time. With this in mind, the general design of the airplane was guided by the belief that a relatively light aircraft producing a fairly large amount of lift would be the best approach. For this reason the Dawdler utilizes a canard rather than a conventional tail for longitudinal control, primarily because the canard contributes a positive lift component. The Dawdler also has a single vertical tail mounted behind the wing for lateral stability, half of which is used as a rudder for yaw control. Due to the fact that the power required to take-off and climb to altitude is much greater than that required for cruise flight and simple turning maneuvers, it was decided that a take-off cart be used. Based on the current design, there are two unknowns which could possibly threaten the success of Project Dawdler. First, the effect of the fully-movable canard with its large appropriation of total lift on the performance of the plane, and secondly, the ability of the take-off procedure to go as planned are examined. These are questions which can only be answered by a prototype.

Bartilotti, Rich↗
NASA NTRS1983

NASA/GE Energy Efficient Engine low pressure turbine scaled test vehicle performance report

The low pressure turbine for the NASA/General Electric Energy Efficient Engine is a highly loaded five-stage design featuring high outer wall slope, controlled vortex aerodynamics, low stage flow coefficient, and reduced clearances. An assessment of the performance of the LPT has been made based on a series of scaled air-turbine tests divided into two phases: Block 1 and Block 2. The transition duct and the first two stages of the turbine were evaluated during the Block 1 phase from March through August 1979. The full five-stage scale model, representing the final integrated core/low spool (ICLS) design and incorporating redesigns of stages 1 and 2 based on Block 1 data analysis, was tested as Block 2 in June through September 1981. Results from the scaled air-turbine tests, reviewed herein, indicate that the five-stage turbine designed for the ICLS application will attain an efficiency level of 91.5 percent at the Mach 0.8/10.67-km (35,000-ft), max-climb design point. This is relative to program goals of 91.1 percent for the ICLS and 91.7 percent for the flight propulsion system (FPS).

Bridgeman, M. J.↗