Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Lightweight Thrust Chamber Composite Overwrap Lessons Learned

The manufacturing, design, and analysis of filament wound carbon fiber/polymer composite overwraps for additively manufactured, copper combustion chambers are a critical part of NASA’s Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project. Ideally, the composite overwrap acts as a light-weight structural jacket and allows significant weight reduction of the high pressure thrust chamber assembly, reduction of overall cost, and reduced fabrication schedules. Chamber assemblies for 2000 lb. (2k) and 7000 lb. (7k) of thrust have been successfully tested at NASA’s Marshall Space Flight Center. Multiple lessons were learned throughout the overwrap process development and manufacturing trials. The lessons learned on small scale hardware, such as the 2k and 7k chambers, will guide further composite manufacturing technologies and enable a progression to larger scale assemblies with greater structural loads. Material performance requirements, manufacturing process development, and surface preparation were evaluated during the small chamber trials, with the broad thermal requirements of the resin being the primary driver for material selection and processing. Both epoxy and bismaleimide (BMI) materials were evaluated with respect to both performance in the hot-fire test and ease of fabrication. Separately, surface preparation procedures were studied with the goal of providing a smooth chamber surface to promote a non-bonded overwrap. Recent testing of the 7k trust chamber has provided data in Non-Destructive Evaluation (NDE) and processing in order to continue to evaluate the performance requirements stated.

Allison Clark↗
NASA NTRS2015

A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing, Part II: Additive Manufacturing and Characterization of Polymer Composites

This publication is the second part of the three part report of the project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing" funded by NASA Aeronautics Research Institute (NARI). The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimides-Ultem 9085 and experimental Ultem 1000 mixed with 10% chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25 to 31%. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties. A preliminary modeling was also initiated to predict the mechanical properties of FDM-printed Ultem 9085 coupons in relation to varied raster angles and void contents, using the GRC-developed MAC/GMC program.

Polymer↗
DOE OSTI2022

Interlayer fusion bonding of semi-crystalline polymer composites in extrusion deposition additive manufacturing

This work focuses on the evolution of interlayer fracture toughness properties of fiber-reinforced, semi-crystalline polymers in the extrusion deposition additive manufacturing (EDAM) process. Further, this work bridges the gap between the additive process conditions (time-temperature history) and the effective layer-to-layer fracture properties developed within a printed component. This is the first step to predict delamination that can occur during printing, during cooling to room temperature after printing, and during service performance of an additively manufactured geometry. A phenomenological model is developed for fusion bonding of semi-crystalline polymer matrix composites by coupling the interdiffusion of polymer chains with the evolution of polymer crystallinity. While the interdiffusion is captured by reptation theory of polymer dynamics, the evolution of crystallinity is modeled by phenomenological crystallization kinetics and crystal melting dynamics. Further, a methodology is developed to determine the critical strain energy release rate, G IC of the interlayer interface and experiments are conducted utilizing the double cantilever beam fracture test geometry. In conclusion, predictions of GIC as a function of thermal history are compared with experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

THE DESIGN OF LAYER TIME OPTIMIZATION IN LARGE SCALE ADDITIVE MANUFACTURING WITH FIBER REINFORCED POLYMER COMPOSITES

In this study, we have developed a method to optimize a layer deposition time (a.k.a. layer time) for large-scale additive manufacturing (AM) via physics-based simulations. A long layer time leads to an over-cooled surface on which a new layer is deposited, and therefore, it may result in a weak bonding or debonding between layers, cracking, or warping. A short layer time leads to a high temperature of the structure due to insufficient cooling, and therefore, the structure may not be stiff enough and may collapse during manufacturing. Therefore, it is important to estimate the optimal layer time in additive manufacturing for a high-quality product. The temperature of a top layer right before deposition is recommended to be slightly higher than the glass temperature of the material. A temperature cooling was approximated to an exponential function of time, and the optimized layer time was obtained based on a target temperature while maintaining a minimal printing time. The material used is carbon fiber-reinforced polycarbonate (CF/PC), and the large-scale deposition system used is LSAM TM from Thermwood Corporation. Three different layer time cases were used for experiments, and a series of thermal images were obtained via an infra-red (IR) camera during the entire AM processes. AM process simulations were performed using a finite element method and the temperature profiles from the simulation were in good agreement with those from experiments. The layer time optimization was performed based on the temperature profiles from the simulations. A layer temperature with the optimal layer time was confirmed as the target temperature through simulation.

Jo, Eonyeon↗
NASA NTRS2010

Personal Aircraft Point to the Future of Transportation

NASA's Small Business Innovation Research (SBIR) and Small Business Technology Transfer (STTR) programs, as well as a number of Agency innovations, have helped Duluth, Minnesota-based Cirrus Design Corporation become one of the world's leading manufacturers of general aviation aircraft. SBIRs with Langley Research Center provided the company with cost-effective composite airframe manufacturing methods, while crashworthiness testing at the Center increased the safety of its airplanes. Other NASA-derived technologies on Cirrus SR20 and SR22 aircraft include synthetic vision systems that help pilots navigate and full-plane parachutes that have saved the lives of more than 30 Cirrus pilots and passengers to date. Today, the SR22 is the world's top-selling Federal Aviation Administration (FAA)-certified single-engine airplane.

Source record↗
DOE OSTI2025

Energy absorption of architectured PrintCast interpenetrating composites in tension

Additively manufactured (AM) metal-metal composites consisting of PrintCasted 316 L austenitic stainless-steel lattice structures infiltrated with A356 casting alloy, have recently been developed for use in high energy absorption systems with potential applications ranging from static load bearing to dynamic blast containment structures. This system has a unique mechanical behavior as the volume fraction of lattice increases showing a transition from localized to de-localized failure and dramatic increase in energy absorption capability. In this work, PrintCast A356/316 L composite tensile specimens were produced with lattice volume fractions ranging from 20 % to 50 % to capture the range of this behavior. Finite element simulations support neutron diffraction measurements of stress state. Results illustrate that in tension, the reinforcement material is in tension while the matrix support material is in compression, information offering significant insight into the transition to de-localized failure. Moreover, the simulation results provide further insight into how interfacial bonding (or lack of bonding) affects the energy absorption capabilities of the PrintCast composites.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Composites From in-Situ Consolidation Automated Fiber Placement of Thermoplastics for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) project Hi-Rate Composites Aircraft Manufacturing (HiCAM) aims to significantly increase commercial aircraft composite structures manufacturing rate. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA has a particular interest in assessing composite structure manufacturing utilizing an in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process employing current state-of-the-art laser heating systems. Three semi-crystalline polyaryletherketone (PAEK) thermoplastic tape materials were characterized to ascertain the ICAT process parameters. The required laser power settings were determined at Electroimpact, Inc., measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. The quality of the resulting test panels was evaluated by both non-destructive evaluation as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various placement temperatures and placement speeds are presented.

thermoplastic composites↗
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2023

Infusible Thermoplastic Composites for Wind Turbine Blade Manufacturing: Fatigue Life of Thermoplastic Laminates under Ambient and Low-Temperature Conditions

Traditionally, thermoset resins such as polyesters (PE) and epoxies are used as the polymer matrix for construction of wind turbine blades. However, concern about their end-of-life treatment garners interest to use thermoplastics for increased recyclability. However, the high viscosity of molten thermoplastics inhibits their use in manufacturing wind turbine blades with injection or compression molding. A recently developed, infusible, reactive thermoplastic resin overcomes this technological barrier. Toward verifying that this recyclable resin is suitable for use in wind turbine blades, a dataset of R?=?0.1 and R?=?10 fatigue data for glass fiber-reinforced acrylic composites is provided and equal fatigue life to industry standard epoxy and unsaturated PE resin systems is demonstrated. Specifically, R?=?0.1 fatigue data for acrylic composites at room temperature and -30?degrees C for verification of low-temperature performance are tabulated. To elucidate failure mechanisms, in situ mechanical testing with X-ray computed tomography demonstrates that damage accumulation occurs by crack propagation along the fiber-matrix interface under cyclic loading. Infrared (IR) thermography predicts failure points in composites specimens with porosity defects introduced from nonideal manufacturing processes. Furthermore, these manufacturing defects are shown to compromise the fatigue life of the acrylic laminates by an order of magnitude.

effect of defects↗
NASA NTRS2016

Tribology of Polymer Matrix Composites (PMCs) Fabricated by Additive Manufacturing (AM)

The integral process of depositing thin layers of material, one after another, until the designed component is created is collectively referred to as Additive Manufacturing (AM). Fused deposition process (FDP) is a type of AM where feedstock is extruded into filaments which then are deposited by 3D printing, and the solidification occurs during cooling of the melt. Currently, complex structures are being fabricated by commercial and open source desktop 3D printers. Recently, metal powder containing composite filaments based on polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) have emerged, which could be utilized for multifunctional applications. For further deployment in the field, especially for aerospace and ground-based applications, it is critical to understand the tribological behavior of 3D printed materials. In this presentation, we will report the tribological behavior of different polymer matrix composites fabricated by fused deposition process. These results will be compared with the base polymer systems. During this study, the tribological behavior of all the samples will be evaluated with tab-on-disc method and compared for different metallic powder reinforcements.

additive manufacturing↗
NASA NTRSDate not supplied

Lightweight Thrust Chamber Composite Overwrap Lessons Learned

Filament winding a polymer/carbon fiber composite overwrap onto an additively manufactured copper combustion chamber will allow it to act as a light-weight structural jacket, significantly reducing weight for high pressure thrust chamber assemblies and reducing overall cost and fabrication schedules. Chamber assemblies for 2k lb. and 7k lb. of thrust have been successfully tested at NASA’s Marshall Space Flight Center. Multiple lessons were learned throughout the overwrap process development and manufacturing trials. The lessons learned on small scale hardware will guide further composite manufacturing technologies and enable a progression to larger scale assemblies with greater structural loads. Material performance requirements, manufacturing process development, and surface preparation were evaluated during the small chamber trials, with the broad thermal requirements of the resin being the primary driver for material selection and processing. Both epoxy and bismaleimide materials were evaluated with respect to both performance in the hot-fire test and ease of fabrication. Separately, surface preparation procedures were studied with the goal of providing a smooth chamber surface to promote a non-bonded overwrap. The recent testing of the 7k trust chamber has provided data in Non-Destructive Evaluation (NDE) and processing in order to continue to evaluate the performance requirements stated.

composite overwrap↗
DOE OSTI2026

A synergistic approach to improve the cellulose nanofibril dispersion in poly(lactic acid) composites as feedstocks for extrusion-based additive manufacturing

Hybrid fiber-reinforced polymer composites (HFRPs) are multifunctional materials that bear more than one characteristic benefit. In this study, hybrid cellulose fibers, e.g., pulp fiber (PF) and cellulose nanofibril (CNF), were used for reinforcing poly(lactic acid) (PLA). A synergistic approach was applied to disperse CNF. The low-surface-tension solvent (ethanol), together with PF templating, assisted the dispersion of CNF in PLA. The HFRP achieved a higher tensile strength (∼70 MPa, 29% increase from PLA) and modulus (∼7 GPa, 46% increase from PLA), as well as a higher heat deflection temperature (∼60℃, 6℃ increase compared to neat PLA), compared to single-reinforcement FRPs. Additionally, the formulation was demonstrated to be potentially suitable for large-scale additive manufacturing.

Bista, Bivek [University of Maine]↗
NASA NTRSDate not supplied

Manufacturing and Scale-Up of Natural Fiber Composite eVTOL Propeller Skin and C-Channel

This presentation discusses the manufacturing and scale-up of natural fiber composites for aerospace applications, conducted within NASA’s Convergent Aeronautics Solutions portfolio to advance aircraft capabilities and efficiency. The effort focused on the development and demonstration of two proof-of concept articles, an electric vertical takeoff and landing (eVTOL) propeller skin and a C-channel subcomponent. Best practices and guidance on addressing key challenges with bio-based composite materials and manufacturing are provided.

Composites↗
NASA NTRS2006

Mechanical Properties of T650-35/AFR-PE-4 at Elevated Temperatures for Lightweight Aeroshell Designs

Considerable efforts have been underway to develop multidisciplinary technologies for aeroshell structures that will significantly increase the allowable working temperature for the aeroshell components, and enable the system to operate at higher temperatures while sustaining performance and durability. As part of these efforts, high temperature polymer matrix composites and fabrication technologies are being developed for the primary load bearing structure (heat shield) of the spacecraft. New high-temperature resins and composite material manufacturing techniques are available that have the potential to significantly improve current aeroshell design. In order to qualify a polymer matrix composite (PMC) material as a candidate aeroshell structural material, its performance must be evaluated under realistic environments. Thus, verification testing of lightweight PMC's at aeroshell entry temperatures is needed to ensure that they will perform successfully in high-temperature environments. Towards this end, a test program was developed to characterize the mechanical properties of two candidate material systems, T650-35/AFR-PE-4 and T650-35/RP46. The two candidate high-temperature polyimide resins, AFR-PE-4 and RP46, were developed at the Air Force Research Laboratory and NASA Langley Research Center, respectively. This paper presents experimental methods, strength, and stiffness data of the T650-35/AFR-PE-4 material as a function of elevated temperatures. The properties determined during the research test program herein, included tensile strength, tensile stiffness, Poisson s ratio, compressive strength, compressive stiffness, shear modulus, and shear strength. Unidirectional laminates, a cross-ply laminate and two eight-harness satin (8HS)-weave laminates (4-ply and 10-ply) were tested according to ASTM standard methods at room and elevated temperatures (23, 316, and 343 C). All of the relevant test methods and data reduction schemes are outlined along with mechanical data. These data contribute to a database of material properties for high-temperature polyimide composites that will be used to identify the material characteristics of potential candidate materials for aeroshell structure applications.

Whitley, Karen S.↗
NASA NTRS2007

Millimeter Wave Holographical Inspection of Honeycomb Composites

Multi-layered composite structures manufactured with honeycomb, foam or balsa wood cores are finding increasing utility in a variety of aerospace, transportation, and infrastructure applications. Due to the low conductivity and inhomogeneity associated with these composites standard nondestructive testing (NDT) methods are not always capable of inspecting their interior for various defects caused during the manufacturing process or as a result of in-service loading. On the contrary, microwave and millimeter wave NDT methods are well-suited for inspecting these structures since signals at these frequencies readily penetrate through these structures and reflect from different interior boundaries revealing the presence of a wide range of defects such as disbond, delamination, moisture and oil intrusion, impact damage, etc. Millimeter wave frequency spectrum spans 30 GHz - 300 GHz with corresponding wavelengths of 10 - 1 mm. Due to the inherent short wavelengths at these frequencies, one can produce high spatial resolution images of these composites either using real-antenna focused or synthetic-aperture focused methods. In addition, incorporation of swept-frequency in the latter method (i.e., holography) results in high-resolution three-dimensional images. This paper presents the basic steps behind producing such images at millimeter wave frequencies and the results of two honeycomb composite panels are demonstrated at Q-band (33-50 GHz). In addition, these results are compared to previous results using X-ray computed tomography.

Case, J. T.↗
NASA NTRS2026

Manufacturing and Scale-Up of Natural Fiber Composite eVTOL Propeller Skin and C-Channel

This report presents the manufacturing and scale-up of natural fiber composites for aerospace applications, conducted within NASA’s Convergent Aeronautics Solutions portfolio to advance aircraft capabilities and efficiency. The effort focused on the development and demonstration of two proof-of-concept articles, an Electric Vertical Take-off and Landing (eVTOL) propeller skin and a C-channel, produced through an iterative design and process optimization approach. Best practices and guidance on addressing key challenges with bio-based composite materials and manufacturing is provided. Ideally suited for non-load-bearing structural components, these emerging materials offer potential for weight reduction, vibration damping, noise mitigation, interference-free communication, and cost savings, without compromising the performance of safety-critical primary structures.

Natural fibers↗
DOE OSTI2026

HYBRID COMPOSITES VIA CO-EXTRUSION ADDITIVE MANUFACTURING-COMPRESSION MOLDING FOR PERFORMANCE OPTIMIZATION

The growing demand for hybrid polymer composites with multifunctional properties has led to the development of various hybridization techniques, such as multi-material compounding and controlled laminate stacking sequence. In this study, a novel hybrid manufacturing approach was used by integrating a multiplexing extrusion system (MExS) based on additive manufacturing with subsequent compression molding process. This technique enabled the co-extrusion of different materials during the additive manufacturing process to fabricate composites with tailored performance. The developed hybrid composite featured a skin layer of glass fiberreinforced polycarbonate (PC/GF) encapsulating a carbon fiber-reinforced acrylonitrile butadiene styrene (CF/ABS) core. The structure was engineered to promote improved thermal and impact resistance at the surface, supported by a stiff core for enhanced overall mechanical integrity. Mechanical, thermal and morphological properties of the hybrid composites were investigated to understand trade-offs in performance compared to a single-material system. The results demonstrate that this approach enables the production of multifunctional composites suitable for applications such as automotive body panels and protective housings, where a balance of weight, mechanical strength, and thermal performance is essential.

Wasti, Sanjita [ORNL]↗