Search NASA⌕ Search

SEARCH · Search NASA

Results for “conductive polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Thermal Conductivity of a Novel Salt-Hydrogel Complex as a Phase Change Material for Building Thermal Management

Use of electricity for space heating, ventilation and air conditioning in buildings may be better managed through temporary energy storage. Compared with electrochemical storage, the levelized cost of thermal energy storage systems can be lower depending on geographical location and thermophysical properties [1]. In any phase change material (PCM), the rate of absorption and release of thermal energy increases with higher thermal conductivity [2]. However, leading PCMs like paraffin waxes have thermal conductivities on the order of 0.1 W/mK. Glauber’s salt, a salt hydrate, possesses a relatively high thermal conductivity but suffers from supercooling and phase segregation. Research has shown that polymer-based composites with salt hydrates can prevent phase segregation and limit supercooling over hundreds of cycles [3] though the thermal conductivity of the composite may be reduced leading to low energy storage rates. Here, we report thermal conductivity measurements on polymer hydrogels which are stable in solutions of Glauber’s salt. To measure thermal conductivity of soft gels, we use a 3-omega method [4] where heat flows bidirectionally through a substrate below and through a gel placed on top. This suits measurements of both gels and liquids unlike transient plane heat source or transient hot wire methods. We report measurements of thermal conductivity of salt-hydrogel complexes as a function of temperature, cross-linking and salt concentration. In addition, we present modeling of thermal conductivity of sodium sulfate solutions with available theories. We finally employ polarized optical microscopy to observe inside the transparent hydrogel networks, showing that precipitating crystals may influence thermal conductivity measurements for high salt concentrations. Our thermal conductivity results combined with enthalpy of phase change, mass density and specific heat are essential to accurately design thermal storage systems for energy-efficient buildings.

composite, thermal conductivity↗
DOE OSTI2022

Structure of Geobacter OmcZ filaments suggests extracellular cytochrome polymers evolved independently multiple times

While early genetic and low-resolution structural observations suggested that extracellular conductive filaments on metal-reducing organisms such as Geobacter were composed of type IV pili, it has now been established that bacterial c -type cytochromes can polymerize to form extracellular filaments capable of long-range electron transport. Atomic structures exist for two such cytochrome filaments, formed from the hexaheme cytochrome OmcS and the tetraheme cytochrome OmcE. Due to the highly conserved heme packing within the central OmcS and OmcE cores, and shared pattern of heme coordination between subunits, it has been suggested that these polymers have a common origin. We have now used cryo-electron microscopy (cryo-EM) to determine the structure of a third extracellular filament, formed from the Geobacter sulfurreducens octaheme cytochrome, OmcZ. In contrast to the linear heme chains in OmcS and OmcE from the same organism, the packing of hemes, heme:heme angles, and between-subunit heme coordination is quite different in OmcZ. A branched heme arrangement within OmcZ leads to a highly surface exposed heme in every subunit, which may account for the formation of conductive biofilm networks, and explain the higher measured conductivity of OmcZ filaments. This new structural evidence suggests that conductive cytochrome polymers arose independently on more than one occasion from different ancestral multiheme proteins.

Cytochromes/metabolism↗
DOE OSTI2020

A Three‐Dimensional Porous Organic Semiconductor Based on Fully sp 2 ‐Hybridized Graphitic Polymer

Abstract Dimensionality plays an important role in the charge transport properties of organic semiconductors. Although three‐dimensional semiconductors, such as Si, are common in inorganic materials, imparting electrical conductivity to covalent three‐dimensional organic polymers is challenging. Now, the synthesis of a three‐dimensional π‐conjugated porous organic polymer (3D p‐POP) using catalyst‐free Diels–Alder cycloaddition polymerization followed by acid‐promoted aromatization is presented. With a surface area of 801 m 2 g −1 , full conjugation throughout the carbon backbone, and an electrical conductivity of 6(2)×10 −4 S cm −1 upon treatment with I 2 vapor, the 3D p‐POP is the first member of a new class of permanently porous 3D organic semiconductors.

Byun, Yearin↗
DOE OSTI2021

Copper Electrode on Flexible Substrate by Intense Pulsed Light Sintering of Microsized Copper Particles

Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.

14 SOLAR ENERGY↗
DOE OSTI2020

Polymer / single-walled carbon nanotube composite for gas detection

A sensor can include a conductive region in electrical communication with at least two electrodes, the conductive region can include a composite of a polymer and SWCNTs immobilized onto a substrate. In certain embodiment, a linker can be grafted on the substrate. The linker can connect the substrate and the composite of the polymer and SWCNTs. In certain embodiments, the linker can covalently bond the polymer to the substrate. In certain embodiments, metal nanoparticles or ions can be incorporated as a metal sensitizer to confer further selectivity or sensitivity to the device. In certain embodiments, the polymer can act as a ligand for a variety of metal ions. By incorporating a specific metal ion, the sensor can selectively detect a specific analyte. In certain embodiments, the composite of the polymer and SWCNTs can be functionalized. In certain embodiments, the composite can further include a sensing element.

Swager, Timothy Manning↗
DOE OSTI2022

Experimental Investigation of Polymer-Induced Fouling of Heater Tubes in the First-Ever Polymer Flood on Alaska North Slope Part II

A polymer flood pilot has been ongoing in the Schrader Bluff viscous oil reservoir at Milne Point on the Alaska North Slope. The results from the pilot are encouraging. However, a major concern of the operator is the influence of polymer on the production system after breakthrough, especially the fouling in heat exchangers. This work applies a multiexperimental approach to study the severity of polymer-induced fouling in both dynamic and static states of produced fluids to determine safe operating conditions. Dynamic scale loop (DSL) tests were conducted to study fouling due to polymer at different skin temperatures (165–350°F) in a dynamic state of fluid flow where the fluids’ flow mimics the residence time of fluids in the heat exchanger of the field pilot. Static deposit tests were also conducted at similar skin temperatures of 165–250°F using a novel experimental apparatus designed and built in-house. It was found that at higher skin temperatures of 250–350°F, tube blocking was observed in the DSL tests, whereas the tests at 165–200°F did not show any tube blocking, even in a more extended test period. The deposit test showed that the deposit rate generally increases with skin temperature, and the presence of polymer aggravates the fouling. The copper tube performs best when the skin temperatures are 165–200°F, while the stainless steel tube performs best at a skin temperature of 250°F. These experiments also manifested the influence of the cloudpoint of the solution as the deposit rate increased significantly when the skin temperature was higher than the solution cloudpoint. The study provides a source of practical guidance to the field operations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The Effects of Morphology and Hydration on Anion Transport in Self-Assembled Nanoporous Membranes

Ordered nanoporous polymer membranes offer opportunities for systematically probing the mechanisms of ion transport under confinement and for realizing useful materials for electrochemical devices. Here, we examine the impact of morphology and ion hydration on the transport of hydroxide and bromide anions in nanostructured polymer membranes with 1 nm scale pores. We use aqueous lyotropic self-assembly of an amphiphilic monomer, with a polymerizable surfactant to create direct hexagonal (H I ) and gyroid mesophases. UV-induced cross-linking leads to the formation of nanoporous polymers with water continuous channels. The membranes are mechanically robust and chemically durable, resisting degradation during extended exposure to 1 M NaOH solutions. We use a combination of electrochemical impedance spectroscopy, pulsed-field gradient NMR spectroscopy, and molecular simulations to elucidate anion and water transport. The as-prepared hexagonal systems display higher conductivity and lower activation energies for both anions relative to the gyroid system. When compared at equivalent hydration, however, gyroid and hexagonal membranes show similar activation energies, with nearly identical conductivities at ambient temperatures. Both ionic conductivity and water diffusivity increase with increasing hydration. Here, the water uptake as a function of relative humidity for the hexagonal and gyroid mesophases ultimately dictates the water diffusion and magnitude of the ionic conductivity, with the hexagonal system showing overall higher capacity for hydration and thus faster ion transport. The durability of these materials under aggressive alkaline conditions and their relatively high hydroxide ion conductivity suggest that these nanostructured polymers could be of interest as membranes for alkaline fuel cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A Study on the Synthesis and Proton Transport Behavior of Multilayered ZSM-5 Zeolite Nanosheet Membranes Laminated on Polymer Substrates

Single crystalline ZSM-5 ZNs with thicknesses around 6 nm were obtained by secondary growth of silicalite nanoparticles using diquaternary bis-1,5(tripropyl ammonium) pentamethylene diiodide (dC5) as a structure-directing agent (SDA). The dC5 could be effectively removed from the ZN pores by either high-temperature calcination or UV irradiation in air at room temperature but not by the piranha solution treatment. Ultrathin ZN-laminated membranes (ZNLMs) were fabricated by sandwiching a UV-activated multilayered ZN film between two recast Nafion® layers (ZNLM-Nafion) and by filtration coating from a suspension of thermally activated ZNs on a nonionic porous PVDF (ZNLM-PVDF). The ZNLMs on both supports demonstrated the ability of highly proton-selective ion conduction with low resistances in aqueous electrolyte solutions. The ZNLM-PVDF with PVDF binder was structurally stable, and it achieved a comparably low ASR but much higher proton selectivity compared with a Nafion membrane of same overall thickness. However, detachment between the ZNLM and Nafion layers occurred when the ZNLM-Nafion operated in aqueous electrolyte solutions. Results of this study show the potential for developing ZNLMs as efficient proton-conducting membranes without using expensive ionic polymer matrices. However, the development of polymer-supported ZNLMs is hindered by the current inefficiency in preparing well-dispersed suspensions of open-pore ZNs. Future development of efficient methods for synthesizing open-pore ZNs in dispersed states is key to realizing high-performance ZNLMs on polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer Precursor Derived Li x PON Electrolytes: Toward Li–S Batteries

Efforts to develop polymer precursor electrolytes that offer properties anticipated to be similar or superior to (lithium phosphorus oxynitride, LiPON) glasses are reported. Such precursors offer the potential to be used to process LiPON-like thin glass/ceramic coatings for use in all solid state batteries, ASBs. Here, LiPON glasses provide a design basis for the synthesis of sets of oligomers/polymers by lithiation of OP(NH 2 ) 3–x (NH) x [from OP(NH) 3 ],OP(NH 2 ) 3-x (NHSiMe 3 ) x and [P=N] 3 (NHSiMe 3 ) 6–x (NH) x . Furthermore, the resulting systems have degrees of polymerization of 5–20. Treatment with selected amounts of LiNH 2 provides varying degrees of lithiation and Li + conducting properties commensurate with Li + content. Polymer electrolytes impregnated in/on Celgard exhibit Li + conductivities up to ~1 × 10 –5 S cm –1 at room temperature and are thermally stable to ~150 °C. A Li–S battery assembled using a Li 6 SiPON composition polymer electrolyte exhibits an initial reversible capacity of 1500 mAh g sulfur –1 and excellent cycle performance at 0.25 and 0.5 C rate over 120 cycles at room temperature.

25 ENERGY STORAGE↗
DOE OSTI2025

Immune-compatible designs of semiconducting polymers for bioelectronics with suppressed foreign-body response

One of the greatest obstacles to achieving implantable electronics with long-term functionality and minimized inflammatory reactions is the immune-mediated foreign-body response (FBR). Recently, semiconducting polymers with mixed electron–ion conductivity have been demonstrated as promising candidates to achieve direct electrical interfacing on bio-tissues. However, there is limited understanding of their immune compatibility in vivo, and strategies for minimizing the FBR through molecular design remain underexplored. Here we introduce a set of molecular design strategies for enhancing the immune compatibility of semiconducting polymers. Specifically, we show that selenophene, when incorporated in the backbone, can mitigate the FBR by suppressing macrophage activation. In addition, side-chain functionalization with immunomodulatory groups decreases the FBR further by downregulating the expression of inflammatory biomarkers. Together, our synthesized polymers achieve suppression of the FBR by as much as 68% (as indicated by the collagen density). In the meantime, these immune-compatible designs still provide a high charge-carrier mobility of around 1 cm 2 V −1 s −1 . In conclusion, we anticipate that such immune-compatible design principles can be translated to a variety of conjugated polymers to suppress the FBR for implantable applications.

Li, Nan [University of Chicago, IL (United States)↗
DOE OSTI2023

Double Doping of Semiconducting Polymers Using Ion-Exchange with a Dianion

The interactions between counterions and electronic carriers in electrically doped semiconducting polymers are important for delocalization of charge carriers, electronic conductivity, and thermal stability. The introduction of a dianions in semiconducting polymers leads to double doping where there is one counterion for two charge carriers. Double doping minimizes structural distortions, but changes the electrostatic interactions between the carriers and counterions. Polymeric ionic liquids (PIL) with croconate dianions are helpful to investigate the role of the counterion in p-type semiconducting polymers. PILs prevent diffusion of the cation into the semiconducting polymers during ion exchange. The redox-active croconate dianions undergo ion exchange with doped semiconducting polymers depending on their ionization energy. Croconate dianions are found to reduce doped films of poly(3-hexyl thiophene), but undergo ion exchange with a polythiophene with tetraethylene glycol side chains, P(g 4 2T-T), that has a lower ionization energy. The croconate dianion maintains crystalline order in P(g 4 2T-T) and leads to a lower activation energy for the electrical conductivity than PF 6 – counterions. The control of the doping level with croconate allows optimization of the thermoelectric performance of the semiconducting polymer. Finally, the thermal stability of the doped films of P(g 4 2T-T) is found to depend strongly on the nature of the counterion.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamics of poly[n]catenane melts

Inspired by advances in the chemical synthesis of interlocking polymer architectures, extensive molecular dynamics simulations have been conducted to study the dynamical properties of poly[n]catenanes-polymers composed entirely of interlocking rings-in the melt state. Both the degree of polymerization (number of links) and the number of beads per ring are systematically varied, and the results are compared to linear and ring polymers. Herein, a simple Rouse-like model is presented, and its analytical solution suggests a decomposition of the dynamics into "ring-like" and "linear-like" regimes at short and long times, respectively. In agreement with this picture, multiple sub-diffusive regimes are observed in the monomer mean-squared-displacements even though interchain entanglement is not prevalent in the system. However, the Rouse-type model does not account for the topological effects of the mechanical bonds, which significantly alter the dynamics at intermediate length scales both within the rings and at the chain segment scales. The stress relaxation in the system is extremely rapid and may be conveniently separated into ring-like and linear-like contributions, again in agreement with the Rouse picture. However, the viscosity has a non-monotonic dependence on the ring size for long chains, which disagrees strongly with theoretical predictions. This unexpected observation cannot be explained in terms of chain disentanglement and is inconsistent with other measures of polymer relaxation. Possible mechanisms for this behavior are proposed and implications for materials design are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synergistically integrated phosphonated poly(pentafluorostyrene) for fuel cells

Modern electrochemical energy conversion devices require more advanced proton conductors for their broad applications. Phosphonated polymers have been proposed as anhydrous proton conductors for fuel cells. However, the anhydride formation of phosphonic acid functional groups lowers proton conductivity and this prevents the use of phosphonated polymers in fuel cell applications. Here, we report a poly(2,3,5,6-tetrafluorostyrene-4-phosphonic acid) that does not undergo anhydride formation and thus maintains protonic conductivity above 200 °C. We use the phosphonated polymer in fuel cell electrodes with an ion-pair coordinated membrane in a membrane electrode assembly. We find that this synergistically integrated fuel cell reached peak power densities of 1,130 mW cm -2 at 160 °C and 1,740 mW cm -2 at 240 °C under H2/O2 conditions, substantially outperforming polybenzimidazole- and metal phosphate-based fuel cells. Our result indicates a pathway towards using phosphonated polymers in high-performance fuel cells under hot and dry operating conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

Innovative Proton Conductive Membranes Based on Two-Dimensional Materials

The team of Oak Ridge National Laboratory, New Mexico State University, and General Graphene Corporation staff will develop and commercialize paradigm-shifting low-cost, high-performing, proton-conductive membranes made from abundant and durable 2D materials. Proposed membranes are expected to be an order of magnitude better in performance and cost compared with the current state-of-the-art formulation, Nafion, and thus are expected to eliminate huge roadblocks in proliferation of fuel cells and flow batteries. The major goal for this work is to develop a fundamentally new learning curve for novel proton exchange membranes needed for various applications. The new technology will overcome the shortcomings of the current state-of-the-art membranes that are based upon Nafion polymer by offering higher proton conductivities, the ability to operate at much lower external humidity levels and higher temperatures (>120°C), and negligible fuel and oxidant crossover through the membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electronic structure manipulation via composition tuning for the development of highly conductive and acid-stable oxides

Exploring materials that simultaneously possess high conductivity and electrochemical stability is critical for various energy-conversion applications. In this study, our combined computations and experiments suggest the Mg–Ti–O chemical space for novel ternary oxide compounds offering high electrical conductivity and corrosion stability in acidic conditions to be potentially used as catalyst supporter of polymer electrolyte membrane fuel cells. High electrical conductivity (6.09 × 10 -1 S cm -1 ) is achieved at room temperature by tuning the chemical composition of Mg 1-x Ti 2+x O 5 while still maintaining good corrosion stability (1.2 × 10 -4 mA cm -2 after six days) in acidic conditions. Furthermore, we discover that a reducing gas environment during the synthesis increases the Ti solubility in Mg 1-x Ti 2+x O 5 with a reduced valence state of Ti, thus resulting in high conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Solution–Doped Donor–Acceptor Copolymers Based on Diketopyrrolopyrrole and 3, 3'–Bis (2–(2–(2–Methoxyethoxy) Ethoxy) ethoxy)–2, 2'–Bithiophene Exhibiting Outstanding Thermoelectric Power Factors with p –Dopants

The design of polymeric semiconductors exhibiting high electrical conductivity (σ) and thermoelectric power factor (PF) will be vital for flexible large-area electronics. In this work, four polymers based on diketopyrrolopyrrole (DPP), 2,3-dihydrothieno[3,4-b][1,4]dioxine (EDOT), thieno[3,2-b]thiophene (TT), and 3, 3'-bis (2-(2-(2-methoxyethoxy) ethoxy) ethoxy)-2, 2'-bithiophene (MEET) are investigated as side-chains, with the MEET polymers newly synthesized for this study. These polymers are systematically doped with tetrafluorotetracyanoquinodimethane ( F 4 TCNQ), CF3SO3H, and the synthesized dopant Cp(CN) 3 -(COOMe) 3 , differing in geometry and electron affinity. The DPP-EDOT-based polymer containing MEET as side-chains exhibits the highest conductivity (σ) ≈700 S cm–1 in this series with the acidic dopant (CF 3 SO 3 H). This polymer also shows the lowest oxidation potential by cyclic voltammetry (CV), the strongest intermolecular interactions evidenced by differential scanning calorimetry (DSC), and has the most oxygen-based functionality for possible hydrogen bonding and ionic screening. Other polymers exhibit high σ ≈300–500 S cm–1 and power factor up to 300 µW m –1 K –2 . The mechanism of conductivity is predominantly electronic, as validated by time-dependent conductance studies and transient thermo voltage monitoring over time, including for those doped with the acid. Furthermore, these materials maintain significant thermal stability and air stability over ≈6 weeks. Density functional theory calculations reveal molecular geometries and inform about frontier energy levels. Raman spectroscopy, in conjunction with scanning electron microscopy (SEM-EDS) and x-ray diffraction, provides insight into the solid-state microstructure and degree of phase separation of the doped polymer films. Infrared spectroscopy enables this study to further quantify the degree of charge transfer from polymer to dopant.

36 MATERIALS SCIENCE↗