Search NASA⌕ Search

SEARCH · Search NASA

Results for “cooling effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Hydraulic concentration of magnetic fields in the solar photosphere. I - Turbulent pumping

Observations suggest that most of the magnetic flux through the solar photosphere is concentrated in vertical filaments in the supergranule boundaries. Each filament appears to contain about 3 times 10 to the 18-th power maxwells, in the form of a field of 500 gauss or more, over a diameter of 700 km or less. The magnetic energy density in the filaments is 100 times the observed kinetic energy density of the observed supergranule motions, but comparable to the kinetic energy density of the granules. Force-free field configurations cannot duplicate the observational numbers, nor can such cooling effects as are believed responsible for the intense fields in sunspot umbrae. We point out a simple hydraulic mechanism (turbulent pumping) that appears to account for the observed concentration of fields.

Parker, E. N.↗
NASA NTRS1974

Heat transfer and film cooling following injection through inclined circular tubes

Film cooling effectiveness and heat transfer are measured downstream of injection through discrete holes into a turbulent mainstream boundary layer. Air is injected through both a single hole and a row of holes spaced at three-diameter intervals and inclined at an angle of 35 deg to the main flow. There is little difference between the heat transfer coefficient with blowing and without blowing at low blowing rates (mass flux ratios). In fact, at low blowing rates, injection is found to decrease somewhat the heat transfer coefficient from that measured without blowing. As the mass flux ratio increases past unity, the heat transfer coefficient increases, especially with injection through a row of holes. The peak heat transfer is usually found at the edge of the spreading jets (i.e., between two holes). At a blowing rate near two, the lateral average of the heat transfer is as much as 27 percent higher than the heat transfer with no blowing. The increase in heat transfer is attributed to the interaction between the jets and the free stream, causing high levels of turbulence.

Eriksen, V. L.↗
NASA NTRS1976

Neutral temperature of cometary atmospheres

Spectral analyses of the coma and type I tails of a comet indicate that the main constituent of a cometary atmosphere is H2O and that cometary nuclei are composed of dirty ice containing mainly CO and N2. Thermochemical calculations on strong infrared coupling between H2O and dust grains explain the dependence of atmospheric temperature on the distance of the comet from the sun considering the strong cooling effect of H2O. It is concluded that atmospheric temperatures of comets cannot be so high as 1500 K.

Shimizu, M.↗
NASA NTRS1976

Cryogenic recovery

Because of the low boiling temperature of cryogenic propellants to be used on the Space Shuttle, loss of cryogens from boiloff could become very costly. This paper describes how this shuttle problem is being solved at Kennedy Space Center. Cryogenic losses are categorized relative to the particular cryogenic involved, the Space Shuttle servicing operation causing boiloff and the magnitude of the loss. The techniques under consideration are discussed in detail. These techniques include reclaiming the boiloff by reliquefaction, upgrading the reclaimed boiloff by purification, and interim boiloff storage in metal hydride prior to reprocessing. One of the reliquefaction processes discussed in detail utilizes the cooling effect of venting some of the liquid hydrogen boiloff to provide a simple hydrogen reliquefaction unit. Possible future applications of these cryogenics recovery techniques to industry and transportation systems using liquid hydrogen for energy storage and fuel are also discussed.

Howard, F. S.↗
NASA NTRS1977

The evaporation of spherical clouds in a hot gas. II - Effects of radiation

The effects of radiation on the evaporation of spherical clouds in a hot medium are considered. The critical cloud radius at which radiative losses balance conductive heating is determined as a function of the external temperature and density. Smaller clouds evaporate, and larger clouds condense. The conditions under which the surfaces of the clouds may be detected are discussed. Net radiative losses for evaporating clouds are calculated, and an effective cooling function for a cloudy medium is obtained. The results may be applied to clouds in supernova remnants, in the interstellar medium, and in clusters of galaxies.

Mckee, C. F.↗
NASA NTRS1977

Further investigation of the spontaneous and evoked activity of the primary neurons of statoreceptors (and other receptors) of the labyrinth of the bullfrog before, during and after an extended period of weightlessness, including alternative intervals of artificial gravity

Vestibular neuron activity was examined by studying nerve stimulation and evoked response. A cooling element, applied to the nerve consisted of a silver hook through which a coolant fluid flowed. Temperature changes were recorded via microtermistors on an eight channel brush recorder, together with response. Diffusion of the cooling effect was measured, recovery time was assessed, and the nerve was then studied hystologically and ultrastructurally. Problems in frog preparation were discussed along with problems in maintaining healthy specimens and bacteria controlled aquaria.

Source record↗
NASA NTRS1978

Fuel consumption improvement in current transport engines

A review is conducted of improvements which can be made with respect to the fuel consumption of current engines and new production versions of current engines. A description is presented of an engine diagnostics program which has the objective to identify and quantify the causes and sources of performance deterioration in the JT9D turbofan engine and to develop basic data which will be applied to minimize performance degradation of current and future engines. General areas where performance losses occur are examined, taking into account seals, blades and vanes, and cases. Potential performance improvement concepts are related to improved component aerodynamics, improved flowpath sealing, blade tip clearance control, improved turbine cooling effectiveness, improved turbine materials and coatings, duct and nozzle aerodynamic refinements, nacelle aerodynamic refinements, forced exhaust mixers, advanced nacelle materials, and advanced fuel control.

Hines, R. W.↗
NASA NTRS1979

The 63 micron radiation field in the earth's thermosphere and its influence on the atomic hydrogen temperature

The thermal escape of hydrogen from the earth's atmosphere is strongly affected by its temperature at the exobase. It has been suggested recently that the hydrogen temperature might be significantly lower than the thermospheric temperature as a result of a collisional exchange of energy with atomic oxygen. The tendency is to cool the hydrogen since the energy of the excited 3P1 level of oxygen can be lost from the atmosphere via magnetic dipole emission of the micron line (3P2-3P1). A detailed calculation of the net cooling effect as a function of altitude throughout the thermosphere is presented. The calculations have been performed for both day and night conditions and for periods of maximum and minimum solar activity conditions. It is found that its effect on Delta T/T varies from a very small value to a maximum of about 3%. The theoretical framework for describing deviations of the 63 micron emission from local thermodynamic equilibrium is given and it is shown that these effects can cause the emission to be reduced by as much as 40% near 500 km.

Durrance, S. T.↗
NASA NTRS1979

A dual-amplifier hot-wire anemometer

The conceptual design of a dual-amplifier constant-temperature hot-wire anemometer is described. This hot-wire anemometer consists of three basic independent modules: a Wheatstone bridge in which the hot wire is one of its arms, an error-correction amplifier, and a voltage-controlled current source. The last two modules constitute the feedback network of this hot-wire anemometer. Thus the output voltage across the wire is a true function of the instantaneous changes in the wire resistance induced by the cooling effect of the flow. The dual-amplifier is capable of reaching relatively high frequency response through adequate selection of its active elements. Suitable gain of the error-correction amplifier and proper choice of the transfer function of the current source has yielded a frequency bandwidth up to 200 kHz.

Sadeh, W. Z.↗
NASA NTRS1980

The upper atmosphere of Uranus - Mean temperature and temperature variations

The number-density, pressure, and temperature profiles of the Uranian atmosphere in the pressure interval from 0.3 to 30 dynes/sq cm are derived from observations of the occultation of SAO 158687 by Uranus on 1977 March 10, observations made from the Kuiper Airborne Observatory and the Cape Town station of the South African Astronomical Observatory. The mean temperature is found to be about 95 K, but peak-to-peak variations from 10 K to 20 K or more exist on a scale of 150 km or 3 scale heights. The existence of a thermal inversion is established, but the inversion is much weaker than the analogous inversion on Neptune. The mean temperature can be explained by solar heating in the 3.3 micron methane band with a methane mixing ratio of 4 x 10 to the -6th combined with the cooling effect of ethane with a mixing ratio of not greater than 4 x 10 to the -6th. The temperature variations are probably due to a photochemical process that has formed a Chapman layer.

Dunham, E.↗
NASA NTRS1983

Gas-Jet Meniscus Control in Ribbon Growth

Gas jet used to control shape of meniscus and thus to regulate ribbon thickness in vertical silicon-ribbon growth. Gas jet also cools ribbon, increasing maximum possible pull speed for silicon, contact angle of 11 degrees plus or minus 1 degree required for constant thickness ribbon growth. Cooling effect of gas jet increases maximum possible pull speed.

Zoutendyk, J. A.↗
NASA NTRS1983

Measuring Surface-Shear Stress in a Wind Tunnel

Two-wire skin friction gage gives both magnitude and direction of mean and fluctuating stresses. Heated wires lie at surface of gage, measure airflow by cooling effect. Wires perpendicular to each other to measure flow direction as well as magnitude. Used successfully in various turbulent flow fields, including separating three-dimensional boundary layer over cone at high angle of incidence.

Lemos, F.↗
NASA NTRS1983

Measurement of heat pump processes induced by laser radiation

A series of experiments was performed in which a suitably tuned CO2 laser, frequency doubled by a Tl3AsSe37 crystal, was brought into resonance with a P-line or two R-lines in the fundamental vibration spectrum of CO. Cooling or heating produced by absorption in CO was measured in a gas-thermometer arrangement. P-line cooling and R-line heating could be demonstrated, measured, and compared. The experiments were continued with CO mixed with N2 added in partial pressures from 9 to 200 Torr. It was found that an efficient collisional resonance energy transfer from CO to N2 existed which increased the cooling effects by one to two orders of magnitude over those in pure CO. Temperature reductions in the order of tens of degrees Kelvin were obtained by a single pulse in the core of the irradiated volume. These measurements followed predicted values rather closely, and it is expected that increase of pulse energies and durations will enhance the heat pump effects. The experiments confirm the feasibility of quasi-isentropic engines which convert laser power into work without the need for heat rejection. Of more immediate potential interest is the possibility of remotely powered heat pumps for cryogenic use, such applications are discussed to the extent possible at the present stage.

Garbuny, M.↗
NASA NTRS1982

Energy efficient engine high-pressure turbine detailed design report

The energy efficient engine high-pressure turbine is a single stage system based on technology advancements in the areas of aerodynamics, structures and materials to achieve high performance, low operating economics and durability commensurate with commercial service requirements. Low loss performance features combined with a low through-flow velocity approach results in a predicted efficiency of 88.8 for a flight propulsion system. Turbine airfoil durability goals are achieved through the use of advanced high-strength and high-temperature capability single crystal materials and effective cooling management. Overall, this design reflects a considerable extension in turbine technology that is applicable to future, energy efficient gas-turbine engines.

Thulin, R. D.↗
NASA NTRS1983

Vertical ascending electrophoresis of cells with a minimal stabilizing medium

Vertical fractionation of a mixture of fixed horse and human red blood cells layered over a stabilizing support medium was done to give a valid comparison with proposed space experiments. In particular, the effects of sample thickness and concentration on zone migration rate were investigated. Electrophoretic mobilities of horse and human cells calculated from zone migration rates were compatible with those obtained by microelectrophoresis. Complete cell separation was observed when low power and effective cooling were employed.

Omenyi, S. N.↗
NASA NTRS1984

Heat transfer and turbulence measurements of a film-cooled flow over a convexly curved surface

Heat transfer and hydrodynamic boundary layer measurements were made in a turbulent boundary layer on a convex surface with 13 rows of injection. Both full- and partial-coverage cases were tested for three blowing ratios: 0.2, 0.4, and 0.6. Heat transfer results are discussed in terms of Stanton number with injection air temperature equal to wall temperature. In the blown region, for both m (blowing ratio) = 0.2 and 0.4, the local response of the boundary layer is dominated by curvature, and m = 0.4 shows higher cooling effects than m = 0.2 or 0.6, as expected, based on flat-plate results. Hydrodynamic measurements with a triple-hot-wire suggest the existence of two streamwise lanes. Lanes containing injection holes are highly affected by injection and show a definite streamwise evolution. Lanes which do not contain holes are not affected much by injection and show little change in the streamwise direction.

Furuhama, K.↗
NASA NTRS1985

Film cooling on a convex wall: Heat transfer and hydrodynamic measurements for full and partial coverage

Turbine-blade cooling is an important issue for high-efficiency turbine engines, and discrete-hole injection is widely used as a cooling method. In the present study, detailed measurements were made of the heat transfer and hydrodynamics of a film-cooled flow on a convex wall, both for full and partial coverage. Two important parameters were altered: the blowing ratio, m, and the number of rows of injection holes. Three values of m were tested: m = 0.2, 0.4, and 0.6. In the blown region, m = 0.4 results in the lowest Stanton numbers of the three blowing ratios tested. This indicates that the value of m = 0.4 is near optimum on the convex wall from the point of view of cooling effect by injection. In the recovery region, Stanton numbers gradually approach the no injection values. Although the heat-transfer behavior during recovery from injection looks relatively complicated, the behavior of Stanton number can be explained in terms of two mechanisms: recovery from the thermal effect of injection and recovery from the turbulence augmentation. This interpretation of the data is supported by the hydrodynamic and temperture-profile measurements. For partial blowing cases, the data follow the full-coverage values inside the blown region. In the unblown region, both in the curved and in the flat plate, the effect of the number of blown rows is clearly seen. Hydrodynamic boundary-layer profiles were measured with the aid of a triple hot-water probe. Three mean-velocity components and six turbulence quantities were simultaneously measured, and inside the blown region strong three-dimensionality was observed.

Furuhama, K.↗