Search NASA⌕ Search

SEARCH · Search NASA

Results for “decelerators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Impact experiments into multiple-mesh targets: Concept development of a lightweight collisional bumper

The utility of multiple-mesh targets as potential lightweight shields to protect spacecraft in low-Earth orbit against collisional damage is explored. Earlier studies revealed that single meshes comminute hypervelocity impactors with efficiencies comparable to contiguous targets. Multiple interaction of projectile fragments with any number of meshes should lead to increased comminution, deceleration, and dispersion of the projectile, such that all debris exiting the mesh stack possesses low specific energies (ergs/sq cm) that would readily be tolerated by many flight systems. The study is conceptually exploring the sensitivity of major variables such as impact velocity, the specific areal mass (g/sq cm) of the total mesh stack (SM), and the separation distance (S) between individual meshes. Most experiments employed five or ten meshes with total SM typically less than 0.5 the specific mass of the impactor, and silicate glass impactors rather than metal projectiles. While projectile comminution increases with increasing impact velocity due to progressively higher shock stresses, encounters with multiple-meshes at low velocity (1-2 km/s) already lead to significant disruption of the glass impactors, with the resulting fragments being additionally decelerated and dispersed by subsequent meshes, and, unlike most contiguous single-plate bumpers, leading to respectable performance at low velocity. Total specific bumper mass must be the subject of careful trade-off studies; relatively massive bumpers will generate too much debris being dislodged from the bumper itself, while exceptionally lightweight designs will not cause sufficient comminution, deceleration, or dispersion of the impactor. Separation distance was found to be a crucial design parameter, as it controls the dispersion of the fragment cloud. Substantial mass savings could result if maximum separation distances were employed. The total mass of debris dislodged by multiple-mesh stacks is modestly smaller than that of single, contiguous-membrane shields. The cumulative surface area of all penetration holes in multiple mesh stacks is an order of magnitude smaller than that in analog multiple-foil shields, suggesting good long-term performance of the mesh designs. Due to different experimental conditions, direct and quantitative comparison with other lightweight shields is not possible at present.

Hoerz, Friedrich↗
NASA NTRS1992

Visualization of entry flow separation for oscillating flow in tubes

Neutrally buoyant helium-filled soap bubbles with laser illumination are used to document entry flow separation for oscillating flow in tubes. For a symmetric entry case, the size of the separation zone appears to mildly depend on Reynolds number in the acceleration phase, but is roughly Reynolds number independent in the deceleration phase. For the asymmetric entry case, the separation zone was larger and appeared to grow somewhat during the deceleration phase. The separation zones for both entry geometry cases remain relatively small throughout the cycle. This is different from what would be observed in all-laminar, oscillator flows and is probably due to the high turbulence of the flow, particularly during the deceleration phase of the cycle.

Qiu, Songgang↗
NASA NTRS1950

The Supersonic Axial-Flow Compressor

An investigation has been made to explore the possibilities of axial-flow compressors operating with supersonic velocities into the blade rows. Preliminary calculations showed that very high pressure ratios across a stage, together with somewhat increased mass flows, were apparently possible with compressors which decelerated air through the speed of sound in their blading. The first phase of the investigation was the development of efficient supersonic diffusers to decelerate air through the speed of sound. The present report is largely a general discussion of some of the essential aerodynamics of single-stage supersonic axial-flow compressors. As an approach to the study of supersonic compressors, three possible velocity diagrams are discussed briefly. Because of the encouraging results of this study, an experimental single-stage supersonic compressor has been constructed and tested in Freon-12. In this compressor, air decelerates through the speed of sound in the rotor blading and enters the stators at subsonic speeds. A pressure ratio of about 1.8 at an efficiency of about 80 percent has been obtained.

Kantrowitz, Arthur↗
NASA NTRS1992

Effect of initial acceleration on the development of the flow field of an airfoil pitching at constant rate

We present results from a series of experiments where an airfoil is pitched at constant rate from 0 to 60 degrees angle of attack. It is well documented that the dynamic stall behavior of such an airfoil strongly depends on the nondimensional pitch rate K = dot-alpha C/(2U(sub infinity)), where C is the chord, dot-alpha the constant pitch rate, and U(sub infinity) the free stream speed. In reality, the actual motion of the airfoil deviates from the ideal ramp due to the finite acceleration and deceleration periods imposed by the damping of drive system and response characteristics of the airfoil. It is possible that the pitch rate alone may not suffice in describing the flow and that the details of the motion trajectory before achieving a desired constant pitch rate may also affect the processes involved in the dynamic stall phenomenon. The effects of acceleration and deceleration periods are investigated by systematically varing the acceleration magnitude and its duration through the initial acceleration phase to constant pitch rate. The magnitude and duration of deceleration needed to bring the airfoil motion to rest is similarly controlled.

Koochesfahani, M. M.↗
NASA NTRS1994

Wake measurements in a strong adverse pressure gradient

The behavior of wakes in adverse pressure gradients is critical to the performance of high-lift systems for transport aircraft. Wake deceleration is known to lead to sudden thickening and the onset of reversed flow; this 'wake bursting' phenomenon can occur while surface flows remain attached. Although 'wake bursting' is known to be important for high-lift systems, no detailed measurements of 'burst' wakes have ever been reported. Wake bursting has been successfully achieved in the wake of a flat plate as it decelerated in a two-dimensional diffuser, whose sidewalls were forced to remain attached by use of slot blowing. Pilot probe surveys, L.D.V. measurements, and flow visualization have been used to investigate the physics of this decelerated wake, through the onset of reversed flow.

Hoffenberg, R.↗
NASA NTRS1994

The Balmer-dominated northeast limb of the Cygnus loop supernova remnant

We present a comprehensive investigation of the Balmar-dominated northeast limb of the Cygnus Loop supernova remnant. Data presented include H alpha (O III), and X-ray images, UV and visible spectrophotometry, and high-resolution spectroscophy. The two relatively bright Balmer-dominated filaments visible on the POSS prints are seen to be part of a very smooth and regular complex of filaments. These filaments mark the current location of the blast wave and are seen to bound the sharply limb-brightened X-ray emission, including the previously reported X-ray, 'halo.' The (O III)/h beta ratio throughout the region is approximately 0.1, except for regions in which the shock is undergoing a transition from nonradiative to incomplete radiative to incomplete radiative conditions. At these locations (O III) emission from the cooling region is quite strong, while collisionally excited Balmer-line emission can be weak because of photoionization of the preshock medium by UV from the nascent cooling region. As a result (O III)/H beta is greater than 100 in some locations. The nonradiative/radiative transition is best studied along the length of the northwestern of the two brightest filaments, where the shock velocity and swept-up column go from approximately 180 km/s and 10(exp 17)/sq cm at one end to approximately 140 km/s and 8 x 10(exp 17)/cm at the other. There are also a number of locations of such incomplete radiative emission where the shock has recently encountered denser regions with characteristic sizes of approximately 10(exp 18) cm. There is a considerable amount of evidence that the shock has decelerated from approximately 400 km/s to less than 200 km/s in the last 1000 yr. We interpret this as the result of the blast wave hitting the wall of a cavity which surround the supernova precursor and succeed in matching a wide range of data with a reflected shock model in which the density ofthe cavity wall is approximately 1.2/cu cm and the density in the interior of the cavity is about 0.09/cu cm. This analysis supports previous suggestions that the Cygnus Loop was a cavity explosion. We opredict that the X-ray shell will continue to brighten for the next 1000 years or so, during which time the shock front will become radiative throughout the northeast region. The similarity of the time scales for post-shock cooling, shock deceleration, and the 1ressure evolution of the region violates assumptions of steady flow, and greatly complicated interpretation of shock specptra in the region. This may be a common and important effect in many supernova remnants. High-resolutoin spectroscopy of the H alpha line profile shows that the broad component is surprisingly narrow (approximately 130 km/s). Consistency between this line width and the shock velocity inferred from spectrophotometry requires either rapid postshock equilibration of T(sub i) and T(sub e), or that the shock front has declerated from 180 km/s to 150 km/s in the last approximately 200 yr. While we cannot unambiguously distinquish between these models, the required deceleration is consistent with extrapolation of the shock decleration rate inferred over the last 1000 years. The width of the narrow component of the h alpha line profile is approximately 3 km/s, which indicates that the preshock medium has been heated to approximately 25,000 K by a shock precursor. The most promising types of precursor are heating either by fast neutrals which overtake the shock or by cosmic rays. In the latter case the observed properties of the precursor constrain the cosmic-ray diffusion coefficient to be between about 10(exp 23) sq cm/s. The characteristics of the precursor seem to be about right to explain the presence of weak (S II) and (N II) emission previously reported by Fesen & Itoh (1985).

Hester, J. Jeff↗
NASA NTRS1996

High lift wake investigation

The behavior of wakes in adverse pressure gradients is critical to the performance of high-lift systems for transport aircraft. Wake deceleration is known to lead to sudden thickening and the onset of reversed flow; this 'wake bursting' phenomenon can occur while surface flows remain attached. Although known to be important for high-lift systems, few studies of such decelerated wakes exist. In this study, the wake of a flat plate has been subjected to an adverse pressure gradient in a two-dimensional diffuser, whose panels were forced to remain attached by use of slot blowing. Pitot probe surveys, L.D.V. measurements, and flow visualization have been used to investigate the physics of this decelerated wake, through the onset of reversed flow.

Sullivan, J. P.↗
NASA NTRS1998

Protein Crystal Growth Under Forced Solution Flow: Experimental Setup and General Response of Lysozyme

We have experimentally studied the effects of solution flow on the growth kinetics of the protein lysozyme. To this end, we have expanded our interferometry setup by a novel crystallization cell and solution recirculation system. This combination permits monitoring of interface morphology and kinetics with a depth resolution of 200 A at bulk flow rates of up to 2000 micron/s. Particular attention was paid to the prevention of protein denaturation that is often associated with the pumping of protein solutions. We found that at bulk flow rates it less than 250 microns/s the average growth rate and step velocity, R(sub avg) and upsilon(sub avg) increase with increasing it. This can be quantitatively understood in terms of the enhanced, convective solute supply to the interface. With high-purity solutions, it u greater than 250 microns/s lead to growth deceleration, and, at low supersaturations sigma, to growth cessation. When solutions containing approx. 1% of other protein impurities were used, growth deceleration occurred at any u greater than 0 and cessation in the low sigma experiments was reached at about half the it causing cessation with pure solution. The flow-induced changes in R(sub avg) and upsilon(sub avg) including growth cessation, were reversible and reproducible, independent of the direction of the u-changes and solution purity. Hence, we attribute the deceleration to the convection-enhanced supply of impurities to the interface, which at higher flow rates overpowers the effects of enhanced interfacial solute concentration. Most importantly, we found that convective transport leads to a significant reduction in kinetics fluctuations, in agreement with our earlier expectations for the lysozyme system. This supports our hypothesis that these long-term fluctuations represent an intrinsic response feature of the coupled bulk transport-interfacial kinetics system in the mixed growth control regime.

Vekilov, P. G.↗
NASA NTRS1999

Roll-Out and Turn-Off Display Software for Integrated Display System

This report describes the software products, system architectures and operational procedures developed by Lockheed-Martin in support of the Roll-Out and Turn-Off (ROTO) sub-element of the Low Visibility Landing and Surface Operations (LVLASO) program at the NASA Langley Research Center. The ROTO portion of this program focuses on developing technologies that aid pilots in the task of managing the deceleration of an aircraft to a pre-selected exit taxiway. This report focuses on software that produces a system of redundant deceleration cues for a pilot during the landing roll-out, and presents these cues on a head up display (HUD). The software also produces symbology for aircraft operational phases involving cruise flight, approach, takeoff, and go-around. The algorithms and data sources used to compute the deceleration guidance and generate the displays are discussed. Examples of the display formats and symbology options are presented. Logic diagrams describing the design of the ROTO software module are also given.

Johnson, Edward J., Jr.↗
NASA NTRS1994

Comment on 'Guidance for an Aerocapture Maneuver

It is stated that the aerodynamic forces on the vehicle being aerocaptured are controlled by "altering the angle of attack" and thereby controlling the lift coefficient. Furthermore, the resulting variation of drag coefficient with angle of attack was ignored. The purpose of this Comment is to point out that an aerodynamic control method that is much more effective than the pitch modulation has been studied and utilized during entries for many years. During aerocapture, it is desirable to have a large range of lift coefficients available, while keeping the vehicle's ballistic coefficients constant. This is accomplished by modulating the vehicle's bank angle, i.e., by rolling the vehicle about its velocity vector. By this method, the angle of attack can be held constant (at the trim angle, if desired), and the C(sub D) and the ballistic coefficient remain constant. Furthermore, the vertical component of the normal force vector (essentially the lift) can be varied over its entire range, from maximum positive to maximum negative values. Reaction controls, rather than aerodynamic ones, are usually utilized to change the bank angle of the vehicle, thus requiring the use of fuel. However, the fuel expenditure that is required to change the bank angle is far less than the amount that would have to be used to continuously hold the vehicle at pitch angles that differ significantly from its trim angle of attack. Also, it has been shown that bank angle modulation to vary the lift can enlarge the entry corridor by increasing the entry angle for the undershoot boundary, where both the heating rate and deceleration reach a maximum. Finally, the crew's deceleration tolerance can be increased somewhat when the bank angle is varied, as opposed to the pitch angle. For bank modulation, the deceleration force vector can be kept at a constant angle with respect to the occupants whose tolerance to g loads is highest when the force is applied in a direction normal to the upper torso. The advantages of bank angle variation to modulate the lift vector were recognized long ago, and this method of control was used successfully on the Apollo command module during lunar return' and, more recently, for the Space Shuttle Orbiter.

Tauber, Michael E.↗
NASA NTRS2002

Demonstration of Land and Hold Short Technology at the Dallas-Fort Worth International Airport

A guidance system for assisting in Land and Hold Short operations was developed and then tested at the Dallas-Fort Worth International Airport. This system displays deceleration advisory information on a head-up display (HUD) in front of the airline pilot during landing. The display includes runway edges, a trend vector, deceleration advisory, locations of the hold line and of the selected exit, and alphanumeric information about the progress of the aircraft. Deceleration guidance is provided to the hold short line or to a pilot selected exit prior to this line. Logic is provided to switch the display automatically to the next available exit. The report includes descriptions of the algorithms utilized in the displays, and a report on the techniques of HUD alignment, and results.

Hyer, Paul V.↗
NASA NTRS1960

An Analysis of the Corridor and Guidance Requirements for Supercircular Entry into Planetary Atmospheres

An analysis is presented of supercircular entry into a planet's atmosphere giving particular attention to the corridor through which spacecraft must be guided in order to accomplish various maneuvers. A dimensionless parameter based on conditions at the conic perigee altitude is introduced for characterizing supercircular entries and conveniently pre-scribing corridor widths associated with elliptic, parabolic, or hyperbolic approach trajectories. The analysis applies to vehicles of arbitrary weight, shape, and size. Illustrative calculations are made for Venus, Earth, Mars, Jupiter, and Titan. For nonlifting vehicles having fixed aerodynamic coefficients, curves are presented of dimensionless parameters from which can be calculated the maximum deceleration, maximum rate of laminar convective heating, and total laminar heat absorbed during single-pass entry at velocities up to twice circular velocity. For lifting vehicles, curves are presented of the maximum deceleration and overshoot boundary of an entry corridor; equations are presented for estimating laminar aerodynamic heating from the maximum deceleration. It is shown that the corridor width is independent of vehicle weight, dimensions, and drag coefficient, provided these are the same at the overshoot boundary as at undershoot. The corridors of certain planets can be broadened markedly by the application of aerodynamic lift; for example, the 10-earth-g corridor width for single- pass, nonlifting, parabolic entry is increased from 0 miles for Jupiter, 7 for Earth, and 8 for Venus, to 52, 51, and 52 miles, respectively, by employing a lift-drag ratio of 1. The use of aerodynamic lift does not increase appreciably the corridors of Mars and Titan. All corridor widths decrease rapidly as the entry velocity is increased. Terminal guidance requirements on accuracy of velocity and flight path angle for successfully entering various corridors are compared with analogous requirements for putting a satellite into orbit, for hitting the moon from the earth, and for achieving ICBM accuracy. Consideration is given to the terminal guidance problem involved in using a planet's atmosphere-rather than rocket fuel-to effect orbital transfers from heliocentric to planetocentric motion, thereby converting a hyperbolic approach trajectory to an elliptic orbit about the target planet. This fuel saving maneuver appears technologically feasible for certain planetary voyages, and implies the possibility of achieving a large reduction in required Earth lift-off weight of chemical propulsion systems.

Chapman, Dean R.↗
NASA NTRS2004

Witnessing the Gradual Slowdown of Powerful Extragalactic Jets: The X-Ray-Optical-Radio Connection

A puzzling feature of the Chandra-detected quasar jets is that their X-ray emission decreases faster along the jet than their radio emission, resulting from an outward-increasing radio-to-X-ray ratio. In some sources this behavior is so extreme that the radio emission peak is located clearly downstream of that of the X-rays. This is a rather unanticipated behavior given that the inverse Compton nature of the X-rays and the synchrotron radio emission are attributed to roughly the same electrons of the jet's nonthermal electron distribution. In this letter we show that this morphological behavior can result from the gradual deceleration of a relativistic flow and that the offsets in peak emission at different wavelengths carry the imprint of this deceleration. This notion is consistent with another recent finding, namely, that the jets feeding the terminal hot spots of powerful radio galaxies and quasars are still relativistic with Lorentz factors GAMMA approximately 2-3. The picture of the kinematics of powerful jets emerging from these considerations is that they remain relativistic as they gradually decelerate from kiloparsec scales to the hot spots, where, in a final collision with the intergalactic medium, they slow down rapidly to the subrelativistic velocities of the hot spot advance speed.

Georganopoulos, Markos↗
NASA NTRS2001

Chronic mitral regurgitation and Doppler estimation of left ventricular filling pressures in patients with heart failure

Previous studies relating Doppler parameters and pulmonary capillary wedge pressures (PCWP) typically exclude patients with severe mitral regurgitation (MR). We evaluated the effects of varying degrees of chronic MR on the Doppler estimation of PCWP. PCWP and mitral Doppler profiles were obtained in 88 patients (mean age 55 +/- 8 years) with severe left ventricular (LV) dysfunction (mean ejection fraction 23% +/- 5%). Patients were classified by severity of MR. Patients with severe MR had greater left atrial areas, LV end-diastolic volumes, and mean PCWPs and lower ejection fractions (each P <.01). In patients with mild MR, multiple echocardiographic parameters correlated with PCWP; however, with worsening MR, only deceleration time strongly related to PCWP. From stepwise multivariate analysis, deceleration time was the best independent predictor of PCWP overall, and it was the only predictor in patients with moderate or severe MR. Doppler-derived early mitral deceleration time reliably predicts PCWP in patients with severe LV dysfunction irrespective of degree of MR.

NASA Discipline Cardiopulmonary↗
NASA NTRS1997

Left ventricular diastolic filling with an implantable ventricular assist device: beat to beat variability with overall improvement

OBJECTIVES: We studied the effects of left ventricular (LV) unloading by an implantable ventricular assist device on LV diastolic filling. BACKGROUND: Although many investigators have reported reliable systemic and peripheral circulatory support with implantable LV assist devices, little is known about their effect on cardiac performance. METHODS: Peak velocities of early diastolic filling, late diastolic filling, late to early filling ratio, deceleration time of early filling, diastolic filling period and atrial filling fraction were measured by intraoperative transesophageal Doppler echocardiography before and after insertion of an LV assist device in eight patients. A numerical model was developed to simulate this situation. RESULTS: Before device insertion, all patients showed either a restrictive or a monophasic transmitral flow pattern. After device insertion, transmitral flow showed rapid beat to beat variation in each patient, from abnormal relaxation to restrictive patterns. However, when the average values obtained from 10 consecutive beats were considered, overall filling was significantly normalized from baseline, with early filling velocity falling from 87 +/- 31 to 64 +/- 26 cm/s (p < 0.01) and late filling velocity rising from 8 +/- 11 to 32 +/- 23 cm/s (p < 0.05), resulting in an increase in the late to early filling ratio from 0.13 +/- 0.18 to 0.59 +/- 0.38 (p < 0.01) and a rise in the atrial filling fraction from 8 +/- 10% to 26 +/- 17% (p < 0.01). The deceleration time (from 112 +/- 40 to 160 +/- 44 ms, p < 0.05) and the filling period corrected by the RR interval (from 39 +/- 8% to 54 +/- 10%, p < 0.005) were also significantly prolonged. In the computer model, asynchronous LV assistance produced significant beat to beat variation in filling indexes, but overall a normalization of deceleration time as well as other variables. CONCLUSIONS: With LV assistance, transmitral flow showed rapidly varying patterns beat by beat in each patient, but overall diastolic filling tended to normalize with an increase of atrial contribution to the filling. Because of the variable nature of the transmitral flow pattern with the assist device, the timing of the device cycle must be considered when inferring diastolic function from transmitral flow pattern.

Non-NASA Center↗
NASA NTRS1947

Ditching Tests with a 1/16-Size Model of the Navy XP2V-1 Airplane at the Langley Tank No. 2 Monorail

Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated. The performance of the node1 was determined and recorded from visual observations, by recording time histories of the longitudinal decelerations, and by taking motion pictures of the ditchings From the results of the tests with the model the following conclusions were drawn: 1. The airplane should be ditched at the normal landing attitude. The flaps should be fully extended to obtain the lowest possible landing speed; 2. Extensive damage will occur in a ditching and the airplane probably will dive violently after a run of about 2 fuselage lengths. Maximum longitudinal decelerations up to about 4g will be encountered; and 3. If a trapezoidal hydroflap 4 feet by 2 feet by 1 foot is attached to the airplane at station 192.4, diving will be prevented and the airplane will probably porpoise in a run of about 4 fuselage lengths with a maximum longitudinal deceleration of less than 3.5g.

Fisher, Lloyd J.↗
NASA NTRS1948

Ditching Tests of a 1/18-Scale Model of the Lockheed Constellation Airplane

Tests were made of a 1/18-scale dynamically similar model of the Lockheed Constellation airplane to investigate its ditching characteristics and proper ditching technique. Scale-strength bottoms were used to reproduce probable damage to the fuselage. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and fuselage configuration were simulated. The behavior of the model was determined from visual observations, by recording the longitudinal decelerations, and by taking motion pictures of the ditchings. Data are presented in tabular form, sequence photographs, and time-history deceleration curves. It was concluded that the airplane should be ditched at a medium nose-high landing attitude with the landing flaps full down. The airplane will probably make a deep run with heavy spray and may even dive slightly. The fuselage will be damaged and leak substantially but in calm water probably will not flood rapidly. Maximum longitudinal decelerations in a calm-water ditching will be about 4g.

Fisher, Lloyd J.↗
NASA NTRS1947

Landing Characteristics in Waves of Three Dynamic Models of Flying Boats

Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact. Landings made at abnormally low trims led to unusually severe bounces during the runout. The least severe landing occurred after a small lending when the model was rapidly decelerated at about 0.4 g in a simulation of the proposed use of braking devices. The severity of the landings increased with wave height and was at a maximum when the wave length was of the order of from one and one-half to twice the over-all length of the model. The models with afterbodies of moderate length frequently bounced clear of the water into a stalled attitude at speeds below flying speed. The model with the long afterbody had less tendency to bounce from the waves and consequently showed less severe accelerations during the landing run than the models with moderate lengths of afterbody.

Benson, James M.↗