Search NASA⌕ Search

SEARCH · Search NASA

Results for “degradation testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Facet‐Selective Deposition of Ultrathin Al 2 O 3 on Copper Nanocrystals for Highly Stable CO 2 Electroreduction to Ethylene

Abstract Catalysts based on Cu nanocrystals (NCs) for electrochemical CO 2 ‐to‐C 2+ conversion with high activity have been a subject of considerable interest, but poor stability and low selectivity for a single C 2+ product remain obstacles for realizing sustainable carbon‐neutral cycles. Here, we used the facet‐selective atomic layer deposition (FS‐ALD) technique to selectively cover the (111) surface of Cu NCs with ultrathin Al 2 O 3 to increase the exposed facet ratio of (100)/(111), resulting in a faradaic efficiency ratio of C 2 H 4 /CH 4 for overcoated Cu NCs 22 times higher than that for pure Cu NCs. Peak performance of the overcoated catalyst (Cu NCs/Al 2 O 3 ‐10C) reaches a C 2 H 4 faradaic efficiency of 60.4 % at a current density of 300 mA cm −2 in 5 M KOH electrolyte, when using a gas diffusion electrode flow cell. Moreover, the Al 2 O 3 overcoating effectively suppresses the dynamic mobility and the aggregation of Cu NCs, which explains the negligible activity loss and selectivity degradations of Cu NCs/Al 2 O 3 ‐10C shown in stability tests.

Li, Hui↗
DOE OSTI2026

Enhanced Electrocatalytic and Cathode‐Electrolyte Interfacial Properties With a Pr‐Based Simple Perovskite/Ruddlesden‐Popper Nanocomposite Cathode in Protonic Ceramic Fuel Cells

The sluggish kinetics and poor stability of the oxygen reduction reaction (ORR) remain the primary bottleneck for achieving high performance in protonic ceramic fuel cells (PCFCs) at intermediate temperatures (400–650°C). In this work, a Pr-based nanocomposite cathode comprised of simple perovskite phase (PrNi 0.7 Co 0.3 O 3-δ ) and Ruddlesden-Popper phase (Co-doped Pr 4 Ni 3 O 10+δ ) is developed. Although PrNi 0.7 Co 0.3 O 3-δ solely stands as a good cathode with facile proton transfer, combining the superior catalytic activity against oxygen on the Ruddlesden-Popper phase boosts the ORR performance further. The designed nanocomposite cathode outperforms the simple perovskite cathode, attributed to enhanced oxygen absorption and surface diffusion with the Ruddlesden-Popper phase. A precursor-based cathode deposition technique is also developed to achieve cathode grain sizes of ∼100 nm. A single cell with the nanocomposite cathode delivers a peak power density of 1.38 W cm −2 at 650°C, among the highest in reported PCFCs with Pr-based cathodes, with a small degradation rate of 0.145 mV h −1 during 250 h stability test. Further investigation of cathode-electrolyte interface revealed interfacial PrO 2 phase formation, promoted by abundant Pr 6 O 11 in the nanocomposite precursor powder, thereby improving both ohmic resistance and stability. These findings highlight the effectiveness of the nanocomposite cathode and underscore its advantages on interfacial properties.

08 - HYDROGEN↗
DOE OSTI2026

Tantalum oxide stabilized molybdenum-doped ruthenium oxide electrocatalysts for PEM water electrolysis

Proton exchange membrane (PEM) water electrolysis offers key advantages, including high current density, high efficiency, and compact system architecture for hydrogen production. However, its widespread implementation is limited by the scarcity and high cost of Ir-based anodic catalysts. Herein, we report an Ir-free electrocatalyst for the acidic oxygen evolution reaction (OER): tantalum oxide (TaO x )–coated molybdenum-doped RuO 2 (TaO x -MoRuO 2 ). The catalyst exhibits a low overpotential of 180 mV at 10 mA cm -2 and excellent durability, with a degradation rate of 0.034 mV h -1 over a 150-hour test at 50 mA cm -2 —surpassing other Ru-based catalysts evaluated under similar conditions. A PEM electrolyzer employing TaO x -MoRuO 2 as the anode maintained stable operation for 100 hours at 500 mA cm -2 . In conclusion, the TaO x coating layer suppresses Ru and Mo dissolution, thus enhancing their stability likely via interfacial electronic reconfiguration of Ru and Mo mediated by bridging oxygen atoms.

Durability↗
DOE OSTI2024

A high-performance intermediate temperature reversible solid oxide cell with a new barrier layer free oxygen electrode

The best solution to address the critical durability issue of solid oxide electrolytic cells (SOECs) for high-efficiency and high-rate H 2 production is to lower the operating temperature without sacrificing the performance. Developing high performance oxygen electrodes (OEs) is a key to capitalizing this solution. Here, in this paper, we report on a highly active OE for intermediate temperature ZrO 2 -based SOECs without a CeO 2 barrier layer. The new barrier-layer-free (BLF) OE is a composite of two materials, (Bi 0.75 Y 0.25 ) 0.93 Ce 0.07 O 1.5±δ (BYC) that exhibits high oxide-ion conductivity and La 0.8 Sr 0.2 MnO 3 (LSM) that possesses a high electronic conductivity to enable fast oxygen reduction/evolution reactions (ORR/OER). Featuring a microscale porous BYC scaffold decorated with high surface area LSM nanoparticles (NPs), the new BLF-OE exhibited a low area specific resistance (ASR) of 0.10 Ω cm 2 at 650 °C in air. With 50%H 2 -50%H 2 O as a feed to hydrogen electrode (HE) and air to OE, the single cell performance achieved 588 mA cm -2 at 0.80 V in the fuel cell mode and 688 mA cm -2 at 1.30 V in the electrolytic mode at 650 °C. Our in-house testing showed that this level of performance was ~3.5x higher than the cell with the benchmark La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ -Ce 0.9 Gd 0.1 O 2-δ OE. The long-term durability testing under alternating fuel cell and electrolytic modes showed a low degradation rate of 0.10 mA cm -2 h -1 over 550 hours. These encouraging results showed the great promise of the newly developed BYC-LSM to be an excellent OE candidate for intermediate temperature SOECs.

25 ENERGY STORAGE↗
DOE OSTI2020

Status and challenges for the application of platinum group metal-free catalysts in proton-exchange membrane fuel cells

Platinum group metal-free (PGM-free) electrocatalysts are an important class of materials for the sustainable energy economy and significant effort has been made towards developing PGM-free catalysts to replace their costly Pt counterparts in fuel cell electric vehicles. The progress made in activity over the last decade is reviewed, along with synthesis strategies for more controlled active site formation and performance gains achieved through electrode engineering. The increased focus on durability, the growing understanding of degradation mechanisms, and the need for standard performance and accelerated stress test protocols are discussed.

25 ENERGY STORAGE↗
DOE OSTI2021

Environmental degradation of electroplated nickel and copper coated SS316H in molten FLiNaK salt

Corrosion of nickel and copper electroplated coatings on SS316H in molten FLiNaK salt was studied. 500- and 1000-hour static corrosion tests were performed in molten FLiNaK at 700 degrees Celsius. Characterization of the coatings following corrosion indicated that they did not degrade in the molten salt during the corrosion experiment and fully protected the underlying SS316H from chromium dissolution. Interdiffusion between the copper coating and SS316H was extremely limited, interdiffusion between the nickel coating and SS316H. Diffusion modelling revealed that the nickel coatings still significantly reduced chromium dissolution over 60 years despite the interdiffusion.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Properties and Autoignition Reactivity of Diesel Boiling Range Ethers Produced from Guerbet Alcohols

We examine the properties of diesel boiling range ethers made from coupling of alcohols produced by oligomerization of ethanol (Guerbet alcohols) for their utility as low-carbon liquid fuel blendstocks. Basic properties of boiling point, flash point, freezing point, density and viscosity are well suited for blending into diesel fuels. For the mixture of ethers the lightest component, di-n-butyl ether, can be present at up to 20 vol% while still having adequately high flashpoint for safe handling. Soot formation tendency (as yield sooting index) is well below that of conventional diesel. The ethers have similar compatibility with elastomers as conventional diesel, based on Hansen solubility parameter analysis. Oxidation stability was assessed for 30 vol% blends of individual ethers in a conventional diesel fuel using a long-term storage test. Over 6 weeks we observed no formation of peroxides or degradation. n-alkyl ethers with carbon number of 8 or higher have cetane number over 100, which is outside the defined range of cetane number, while branched ethers are over 70. The ethers also blend antagonistically into conventional diesel for cetane number, meaning that the blend cetane value is lower than predicted based on a linear by volume, mass, or mole model. We show that aromatics and naphthenes likely act as radical scavengers to slow or shut down autoignition of the highly reactive ethers at low to medium blend levels. Overall, diesel boiling range ethers show significant promise as high quality low-net carbon diesel blendstocks.

09 BIOMASS FUELS↗
DOE OSTI2026

Challenges, Technological Pathways and Trade-Offs of Perovskite Solar Modules for Long-Term Operation

Perovskite solar modules (PSMs) have emerged as a promising photovoltaic technology due to their high efficiency, low fabrication cost and compatibility with lightweight and flexible applications. However, ensuring long-term reliable performance under real-world conditions remains a critical barrier to commercialization. PSMs degrade through mechanisms that differ substantially from those affecting established technologies such as silicon, particularly under environmental stressors like ultraviolet light, oxygen, temperature cycling and reverse bias. Here we provide an analysis of the degradation pathways specific to perovskite modules and discuss why standard accelerated tests often fail to predict outdoor performance. We conceptualize challenges across material, device and module levels and evaluate strategies to mitigate ion migration, interfacial breakdown and encapsulation failure. By highlighting the need for realistic testing protocols and durable materials, we propose a framework highlighting key challenges, technological pathways and the trade-offs required to extend perovskite module lifetimes towards long-term operation, aiming to guide the development of PSMs capable of a 30-year operational lifetime.

14 SOLAR ENERGY↗
DOE OSTI2024

Spot size measurement of a deuterium–tritium dense plasma focus using neutron radiography

Neutron radiography is a technique uniquely suited to applications in nuclear diagnostics, non-destructive testing, and subcritical experiments. The spatial resolution of neutron radiographs is degraded by optical blur in the imaging system and the neutron source size, where the ideal source is point-like to optimize the point-spread function. A potential neutron source for radiography is the dense plasma focus (DPF), a coaxial Z-pinch that produces thermonuclear and beam-target neutrons. To assess if the source size is suitable for radiography, a neutron imaging system was used to measure the source size of the 4 MA Sodium DPF at the Nevada National Security Site operating with deuterium–tritium gas-fill. The source size was measured using the edge-spread function of tungsten objects, each having a rolled (convex) edge. The spot size was found to be 7–12 mm full-width at half-max (FWHM) assuming a Gaussian source, though comparison is presented for Lorentzian and Bennett distributions. The average FWHM was found to be 8.6 ± 1.2 mm vertically and 10.8 ± 1.2 mm horizontally with respect to the image plane, averaging over varied edges and alignments. The results were sensitive to source alignment and edge metrology, which introduced notable uncertainties. These results are consistent with separate experimental measurements as well as magnetohydrodynamics simulations of this DPF, which suggest that neutron production can originate from pinches ∼5–7 mm off-axis. These results suggest that the DPF should be used for radiography at low magnification (M < 1) where spot size does not dominate spatial blur.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Characterization of an architecture for front-end pixel binning in an integrating pixel array detector

Optimization of an area detector involves compromises between various parameters like frame rate, read noise, dynamic range and pixel size. We have implemented and tested a novel front-end binning design in a photon-integrating hybrid pixel array detector using the MM-PAD- 2.0 pixel architecture. In this architecture, the pixels can be optionally binned in a 2 x 2 pixel configuration using a network of switches to selectively direct the output of 4 sensor pixels to a single amplifier input. Doing this allows a trade-off between frame rate and spatial resolution. Tests show that the binned pixels perform well, but with some degradation on performance as compared to an un-binned pixel. The increased parasitic input capacitance does reduce the signal collected per x-ray as well as increases the noise of the pixel. Here, the increase in noise is, however, less than the factor of 2 increase one would observe for binning in post-processing. Spatial scans across the binned pixels show that no measured signal intensity is lost at the inner binning unit boundaries. In the high flux regime, at a 2 x 2 pixel wide beam spot (FWHM) size, binned mode responds linearly up to a photon flux of 10 7 x-rays/s, and performs comparably with un-binned mode up to a photon flux of 10 8 x-rays/s. While this study demonstrates a proof of concept for front-end binning in integrating detectors, we also identify changes to this early-stage prototype which can further improve the performance of binning pixel structures.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Screening Metal Halide Perovskite Solar Modules for Premature Field Failures

Developing metal halide perovskite (MHP) photovoltaic (PV) devices into reliable large-area solar modules could accelerate global solar energy deployment. Many MHP devices are susceptible to degradation under light and elevated temperature (LT). Published research on LT testing is limited at the module level, and LT testing has not yet been developed for qualification testing of commercial PV products. This report assesses whether results of LT testing at moderately elevated temperatures correlate with those of field-tested modules from the same batch. Six batches of samples from four manufacturers are assessed. It is shown that modules with a robust package that can maintain over 80% of their peak efficiency during LT testing at 55 °C for 100 h are more likely to retain over 80% of their peak efficiency during outdoor operation for 10 weeks. This finding is a step towards developing a validated test protocol that could be incorporated into a qualification standard for the commercialization of MHP PV technologies.

14 SOLAR ENERGY↗
DOE OSTI2024

Process Innovations for High Temperature Superconducting (HTS) Wire Manufacturing

Thermal and strain cycling tests for STI’s coated conductor have been performed with our newly updated critical current/tensile tester. The original goal was to carry out 1000 thermal cycles and 1000 strain cycles and measure Ic for pre and post cycling. The tape exceeded the goal. Thermal testing was successful with 2900 cycles and strain testing was carried out for 2000 cycles without any significant Ic degradation. Another important milestone was to produce lengths greater than 100m, a 2X improvement over reported performance reported in Q4/2019 report was completed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Improved Compaction Experiments and Modeling of Waste Isolation Pilot Plant Standard, Non-degraded, Waste Containers

A credible simulation of disposal room porosity at the Waste Isolation Pilot Plant (WIPP) requires a tenable compaction model for the 55-gallon waste containers within the room. A review of the legacy waste material model, however, revealed several out-of-date and untested assumptions that could affect the model’s compaction behavior. For example, the legacy model predicted non-physical tensile out-of-plane stresses under plane strain compression. (Plane strain compression is similar to waste compaction in the middle of a long drift.) Consequently, a suite of new compaction experiments were performed on containers filled with surrogate, non-degraded, waste. The new experiments involved uniaxial, triaxial, and hydrostatic compaction tests on quarter-scale and full-scale containers. Special effort was made to measure the volume strain during uniaxial and triaxial tests, so that the lateral strain could be inferred from the axial and volume strain. These experimental measurements were then used to calibrate a pressure dependent, viscoplastic, constitutive model for the homogenized compaction behavior of the waste containers. This new waste material model’s predictions agreed far better with the experimental measurements than the legacy model’s predictions, especially under triaxial and hydrostatic conditions. Under plane strain compression, the new model predicted reasonable compressive out-of-plane stresses, instead of tensile stresses. Moreover, the new model’s plane strain behavior was substantially weaker for the same strain, yet substantially stronger for the same porosity, than the legacy model’s behavior. Although room for improvement exists, the new model appears ready for prudent engineering use.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Fabrication and Testing of Micro Flux Monitors in the High Flux Isotope Reactor

Neutron dosimetry is a critical technique to measure the neutron flux, fluence, and energy spectrum of nuclear reactors and can be used to indicate fuel reloading, high-power operations, or changes in cycle length. This work presents results of a novel device named the micro flux monitor, which is a miniaturized neutron dosimeter made from small quantities (100s of nanograms) of Ti, Al, Ni, and Au metals deposited on Si and high-purity fused silica substrates using standard semiconductor fabrication techniques. Approximately 1,250 of these devices were produced, and 40 were irradiated in the pneumatic tube facility of the Neutron Activation Analysis Laboratory at the High Flux Isotope Reactor. Testing demonstrated that dosimeter metals can be deposited predictably and repeatedly in multiple geometries, including as quick response (QR) codes. Neutron flux measurements with these devices were within 3% of measurements made using standard flux monitors, demonstrating the efficacy of these devices. Devices were also tested at 500°C under a N2 atmosphere and showed minimal degradation, suggesting they could be deployed for neutron dosimetry measurements in high-temperature advanced reactors.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Exploring the Use of Flexible Circuit Boards to the Increase Power Density of a Rotary Triboelectric Nanogenerator

EExpansion on previous triboelectric nanogenerator (TENG) research that investigated a freestanding rotary TENG. The previous prototype used a single printed circuit board (PCB) stator with exposed copper electrodes and an arcylic rotor with vinyl-cut fluorinated ethylene propylene (FEP) wedges. The second generation prototype again used a PCB stator but used a flexible PCB rotor consisting of alternating polyamide and copper wedges. This prototype was assembled in a stacked configuration, with the intent of increasing current output. Results indicated that the internal resistance of the prototype was decreased, allowing for higher current output. However, degradation of the power output was observed, which led to decay testing of the prototypes. To overcome charge decay, a self-exciting design is suggested as further work.

42 ENGINEERING↗
DOE OSTI2026

Battery Life Prediction Using Reduced-Order Physics Models and Machine Learning (CRADA Final Report)

Phase 1 (Original CRADA, plus no-cost extension modifications #1-3, 6/1/2017 to 3/13/2021): The Australian Department of Defence (AUDoD) is performing accelerated aging tests of Li-ion batteries to benchmark their reliability and degradation characteristics. Using its previously developed battery lifetime predictive model framework, the National Laboratory of the Rockies (NLR) will develop analytical models based the AUDoD data to predict lifetime of the multiple Li-ion battery chemistries under real-world use scenarios of interest to AUDoD. The NLR model is based on physical degradation mechanisms encountered by Li-ion batteries and has been previously validated. Phase 2 (CRADA modification #4, plus no-cost extension modification #5, 2/22/2021 to 3/30/2025): Train and support Australian Department of Defence personnel to use NLR software for model-based estimation of Li-ion battery lifetime using accelerated battery aging data collected by the Australian Department of Defence. Under separate DOE funding from 2019 to 2021, NLR enhanced its battery life-prediction software using machine learning algorithms to automate portions of the model-fitting process, requiring significantly less labor and expert judgment and also adding uncertainty quantification, increasing statistical rigor. Under Phase 2, NLR will customize NLR Software and provide it to AuDoD. NLR will enhance its NLR Model to capture aging modes of AuDoD's multi-cell modules, including cell-balancing effects. NLR will develop example single-cell and multi-cell models based on one AuDoD battery aging dataset. NLR will train AuDoD personnel on NLR Software. By the conclusion of the project, NLR will have provided AuDoD the training materials, a user manual and software needed to perform their own analysis of additional and/or future battery aging datasets.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

A Review of the Research and Development of Brayton Cycle Technology in Nuclear Power Applications with a Focus on Compressor Technology

This study reviews the integration of Brayton Cycle (BC) systems in nuclear power generation, emphasizing their potential to enhance thermal efficiency and operational flexibility over traditional Rankine Cycle (RC) systems. Key working fluids, such as helium (He), supercritical carbon dioxide (sCO 2 ), nitrogen (N 2 ), and air, are evaluated for their performance, efficiency, and compatibility with nuclear systems. He is recognized for its high thermal conductivity and inertness at elevated temperatures, while sCO 2 demonstrates advantages in compactness and efficiency in midrange temperatures. This article also highlights the importance of compressor designs in optimizing BC performance and reviews, available compressor technologies. Axial and centrifugal compressor designs enable efficient gas compression while managing the thermal and mechanical stresses associated with high-pressure operations in nuclear systems. Combined with variable geometry components and advanced materials, these technologies address the challenges posed by varying load conditions. Despite the promising features of BC systems, several challenges persist, including high leakage rates and material degradation under extreme conditions, which necessitate robust sealing technologies and thorough testing. The insights gained from operational experiences at facilities, such as the Oberhausen II plant and the High-Temperature He Test Facility (HHV), underscore the complexities involved in designing high-temperature gas turbines for nuclear applications. This review concludes that as the nuclear industry evolves, BC systems hold significant promise for contributing to a sustainable energy future, particularly in the context of small modular reactors (SMRs) and microreactors. Further exploration of combined cycle configurations that combine BCs with RCs may enhance overall efficiency and flexibility in power generation.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Nanomechanical and Fluorescence Characterizations of Weathered PV Module Encapsulation

Nanoindentation and fluorescence spectroscopy provide spatially resolved mechanical and chemical characterization for degradation of poly (ethylene-co-vinyl acetate) (EVA) encapsulants aged under accelerated weathering and in field deployed photovoltaic (PV) modules. For the accelerated weathering tests, two different EVA formulations in the glass/EVA/glass-laminated coupons were exposed to ultraviolet (UV) light for 180 days at three different temperatures (40, 60, and 80 °C) and UV intensities (0.4, 2.2, and 2.9 W/m2/nm at 340 nm). The fluorescence spectra and moduli were uniform through the cross section of both EVA formulations at the lowest temperature and UV intensity; however, under the highest temperature and UV intensity, the UV irradiated sides showed lower moduli and higher fluorescence compared to the opposite sides. For EVA obtained from PV modules deployed 27 years in Sacramento, CA, USA, changes in fluorescence intensity across the thickness were relatively greater than changes in modulus. On the other hand, for EVA obtained from the same type of module stored in the shed for 27 years, no fluorescence was observed, and a uniform modulus was seen through the EVA layer, but with substantially higher values than those obtained from the field-deployed modules. The different extent of changes between laboratory and field exposures suggests the importance of considering effects of temperature and UV intensity for designing a reliable accelerated testing. This study uniquely demonstrates the capability of microscale characterization using nanoindentation and fluorescence microscopy to monitor mechanical and chemical degradation of EVA encapsulants in PV modules.

14 SOLAR ENERGY↗