Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastomer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Mixed mode stress field effect in adhesive fracture

Numerical or analytical analyses were performed on seven different test specimens including blister test, 90-degree peel test, torsion test, and various cone tests. These specimens are in general subjected to complex stress fields having various amounts of Mode I, Mode II, and Mode III loads. The specimens were then constructed using polymethyl methacrylate for the adherends and a transparent polyurethane elastomer (Solithane 113) for the adhesive. This combination permitted direct observation of the bondline as load was applied. Although initial debonds as well as bond end termination singularities were present in all specimens, in some cases the debond did not initiate at the singularity points as would normally have been expected. An explanation for this behavior is presented, as well as a comparison of loading mode effect on those specimens for which the debond did propagate from a bond terminus singular point.

Anderson, G. P.↗
NASA NTRS1974

Effect of crosslinking density on biaxial relaxation of SBR by using reduced variables

The use of reduced variables to account for the effect of crosslinking density in a styrene-butadiene rubber (SBR) system is demonstrated for general biaxial stress states. Recently published results from stress relaxation tests on five SBR vulcanizates crosslinked to different degrees by tetramethylthiuram disulfide were superposed by using the crosslinking density as a reduction variable. The equilibrium shear modulus calculated from the master relaxation curve at long reduced times was in satisfactory agreement with other results for SBR. The time-axis shifts were related in a linear logarithmic manner to the crosslinking density but had a slope slightly less than values previously reported for elastomer systems.

Arenz, R. J.↗
NASA NTRS1974

A new mechanism of failure on polymers

Transparent laminates containing imbedded crystals of various ionic and nonionic substances were prepared and their swelling in distilled water was observed. It was found that under certain conditions, disk-shaped cracks formed around the swollen pockets containing a dissolving crystal. Such cracks can form before equilibrium swelling is reached and may severely damage the elastomer.

Fedors, R. F.↗
NASA NTRS1976

Long-life mission reliability for outer planet atmospheric entry probes

The results of a literature analysis on the effects of prolonged exposure to deep space environment on the properties of outer planet atmospheric entry probe components are presented. Materials considered included elastomers and plastics, pyrotechnic devices, thermal control components, metal springs and electronic components. The rates of degradation of each component were determined and extrapolation techniques were used to predict the effects of exposure for up to eight years to deep space. Pyrotechnic devices were aged under accelerated conditions to an equivalent of eight years in space and functionally tested. Results of the literature analysis of the selected components and testing of the devices indicated that no severe degradation should be expected during an eight year space mission.

Mccall, M. T.↗
NASA NTRS1975

Molecular correlations with fracture in fibers and granular-filled composites

Results are presented for an experimental electron spin resonance study of chain-scission kinetics in oriented nylon fibers and in granular-filled elastomer composites. A reaction-rate molecular model is proposed as a tool to predict failure under various loadings. The model assumes a statistical distribution in stress on the polymeric chain structure. Interfacial failure in the filled composites is examined. Failure at the interface between the filler and the matrix may be largely adhesive or cohesive, depending on the magnitude of the interactive forces. It appears that the mechanical behavior of both single-component and filled composites depends on the composite nature of the structure. The electron spin resonance technique is shown to be suitable for experimental observation of phenomena directly related to atomic occurrences.

Devries, K. L.↗
NASA NTRS1975

Syntheses and degradations of fluorinated heterocyclics

The relative stability of two ring systems, the triazine rings and 1,2,4-oxadiazoles, which offer potential crosslinks useful for curing perfluoroalkyl ether elastomers, has been investigated. Tris (perfluoro-n-heptyl)-s-triazine, the perfluoroether substituted-s-triazine, 1,4-bis/(5-perfluoro-n-heptyl)-1,2,4-oxadiazolyl/benzene, its perfluoroalkyl ether substituted analog, and 3,5-bis-(perfluoro-n-heptyl)-1,2,4-oxadiazole were synthesized and subjected to thermal and oxidative degradation at 235 and 325 C and to hydrolytic degradation at 235 C. The perfluoroalkyl ether substituted triazine and 3,5-bis(perfluoro-n-heptyl)-1,2,4-oxadiazole were found to be stable under all conditions investigated.

Paciorek, K. L.↗
NASA NTRS1976

Nonelastomeric Rod Seals for Advanced Hydraulic Systems

Advanced high temperature hydraulic system rod sealing requirements can be met by using seals made of nonelastomeric (plastic) materials in applications where elastomers do not have adequate life. Exploratory seal designs were optimized for advanced applications using machinable polyimide materials. These seals demonstrated equivalent flight hour lives of 12,500 at 350 F and 9,875 at 400 F in advanced hydraulic system simulation. Successful operation was also attained under simulated space shuttle applications; 96 reentry thermal cycles and 1,438 hours of vacuum storage. Tests of less expensive molded plastic seals indicated a need for improved materials to provide equivalent performance to the machined seals.

Hady, W. F.↗
NASA NTRS1976

Advanced supersonic technology fuel tank sealants

Status of the fuel tank simulation and YF-12A flight tests utilizing a fluorosilicone sealant is described. New elastomer sealant development is detailed, and comparisons of high and low temperature characteristics are made to baseline fluorosilicone sealants.

Rosser, R. W.↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS1977

Reduced variable technique for predicting grain behavior

The use of reduced variables to account for the time-temperature dependence of the relaxation modulus is a standard and universally adopted technique in the stress analysis of solid propellant grains. Recent work has suggested that the reduced variable technique can also be used to account for the dependence of the relaxation modulus on the crosslink density of an elastomer system. By combining variables, it is now possible to determine the relaxation modulus as a function of both mechanical and chemical parameters over a long period of time. The problems involved, the pitfalls to be avoided, and suggested techniques to be used in acquiring data are discussed.

Lewis, G. W.↗
NASA NTRS1977

Stiffness and damping of elastomeric O-ring bearing mounts

A test rig to measure the dynamic stiffness and damping of elastomer O rings was described. Test results for stiffness and loss coefficient in the frequency range from 50 Hz to 1000 Hz are presented. Results are given for three different materials, for five temperatures, for three amplitudes, for five values of squeeze for three values of stretch for three values of cross-section diameter and for three values of groove width. All test data points were plotted. In addition, trend summary plots were presented which compare the effect of material, temperature, amplitude, squeeze, stretch, cross-section diameter, and groove width. O ring deflections under a static load for different material were presented; and effective static stiffness values were compared with dynamic values.

Smalley, A. J.↗
NASA NTRS1978

Advanced solid electrolyte cell for CO2 and H2O electrolysis

A solid electrolyte cell with improved sealing characteristics was examined. A tube cell was designed, developed, fabricated, and tested. Design concepts incorporated in the tube cell to improve its sealing capability included minimizing the number of seals per cell and moving seals to lower temperature regions. The advanced tube cell design consists of one high temperature ceramic cement seal, one high temperature gasket seal, and three low temperature silicone elastomer seals. The two high temperature seals in the tube cell design represent a significant improvement over the ten high temperature precious metal seals required by the electrolyzer drum design. For the tube cell design the solid electrolyte was 8 mole percent yttria stabilized zirconium oxide slip cast into the shape of a tube with electrodes applied on the inside and outside surfaces.

Shumar, J. W.↗
NASA NTRS1978

Owens-Illinois liquid solar collector materials assessment

From the beginning, it was noted that the baseline drawings for the liquid solar collector exhibited a distinct weakness concerning materials specification where elastomers, plastics, and foam insulation materials were utilized. A relatively small effort by a competent design organization would alleviate this deficiency. Based on results obtained from boilout and stagnation tests on the solar simulator, it was concluded that proof testing of the collector tubes prior to use helps to predict their performance for limited service life. Fracture mechanics data are desirable for predicting extended service life and establishing a minimum proof pressure level requirement. The temperature capability of this collector system was increased as the design matured and the coating efficiency improved. This higher temperature demands the use of higher temperature materials at critical locations in the collector.

Nichols, R. L.↗
NASA NTRS1978

Wear of steel by rubber

Wear of a steel blade used as a scraper to abrade rubber surfaces has been found to take place much more rapidly on a cis-polyisoprene (natural rubber) surface than on a cis-polybutadiene surface, and much more rapidly in an inert atmosphere than in air. These observations are attributed to the direct attack upon steel of free-radical species generated by mechanical rupture of elastomer molecules during abrasion.

Gent, A. N.↗
NASA NTRS1979

Removing overcoatings from microcircuits

Silicone resin of elastomer overcoatings are removed more quickly from microcircuit chips with hot concentrated sulfuric acid. Process takes few minutes as compared to day or two, using commercial solvents based on toluene, xylene, and like. Overcoatings are removed to expose circuit for failure analysis.

Belcher, J. G., Jr.↗
NASA NTRS1980

Post-processing flame-retardant for polyurethane

Treatment of polyurethane form with elastomer formulation after processing makes foam fire resistant without compromising physical properties. In testing, once ignition source is removed, combustion stops. Treatment also prevents molten particle formation, generates no smoke or toxic gases in fire, and does not deteriorate under prolonged exposure to Sun.

Monaghan, P.↗
NASA NTRS1979

Modeling of polymer networks for application to solid propellant formulating

Methods for predicting the network structural characteristics formed by the curing of pourable elastomers were presented; as well as the logic which was applied in the development of mathematical models. A universal approach for modeling was developed and verified by comparison with other methods in application to a complex system. Several applications of network models to practical problems are described.

Marsh, H. E.↗
NASA NTRS1978

The practical impact of elastohydrodynamic lubrication

Elastohydrodynamic lubrication has had its most significant impact on, among all the types of concentrated contact mechanisms, rolling element bearings. EHL technology, through its inclusion in computer codes, now provides us with more effective methods for optimizing bearing design and for predicting bearing life, power loss, temperature and dynamic behavior. Bearing life prediction has advanced to a much more sophisticated level as compared to the calculation of fatigue life based on Lundberg-Palmgren theory. Application of elastohydrodynamics to gearing has, more or less, been limited to the calculation of pitch point film thicknesses. Techniques for calculating film thicknesses over the entire range of tooth meshes for arbitrarily shaped gear teeth (noninvolute, spur, helical, etc.) need to be developed. Elastomer seals with both unidirectional and reciprocating motion offer a fruitful application for the elastohydrodynamics of low modulus materials.

Anderson, W. J.↗