Search NASA⌕ Search

SEARCH · Search NASA

Results for “empirical pressures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

SiC and Si3N4 Recession Due to SiO2 Scale Volatility Under Combustor Conditions

Silicon carbide (SiC) and Si3N4 materials were tested in various turbine engine combustion environments chosen to represent either conventional fuel-lean or fuel-rich mixtures proposed for high-speed aircraft. Representative chemical vapor-deposited (CVD), sintered, and composite materials were evaluated by furnace and high-pressure burner rig exposures. Although protective SiO2 scales formed in all cases, the evidence presented supports a model based on paralinear growth kinetics (i.e., parabolic growth moderated simultaneously by linear volatilization). The volatility rate is dependent on temperature, moisture content, system pressure, and gas velocity. The burner tests were thus used to map SiO2 volatility (and SiC recession) over a range of temperatures, pressures, and velocities. The functional dependency of material recession (volatility) that emerged followed the form A[exp(-Q / RT)](P(sup x)v(sup y). These empirical relations were compared with rates predicted from the thermodynamics of volatile SiO and SiOxHy reaction products and a kinetic model of diffusion through a moving boundary layer. For typical combustion conditions, recession of 0.2 to 2 micrometers/hr is predicted at 1200 to 1400 C, far in excess of acceptable long-term limits.

Smialek, James L.↗
NASA NTRS2010

Combustion Stability Analyses of Coaxial Element Injectors with Liquid Oxygen/Liquid Methane Propellants

Liquid rocket engines using oxygen and methane propellants are being considered by the National Aeronautics and Space Administration (NASA) for in-space vehicles. This propellant combination has not been previously used in a flight-qualified engine system, so limited test data and analysis results are available at this stage of early development. NASA has funded several hardware-oriented activities with oxygen and methane propellants over the past several years with the Propulsion and Cryogenic Advanced Development (PCAD) project, under the Exploration Technology Development Program. As part of this effort, the NASA Marshall Space Flight Center has conducted combustion stability analyses of several of the configurations. This paper presents test data and analyses of combustion stability from the recent PCAD-funded test programs at the NASA MSFC. These test programs used swirl coaxial element injectors with liquid oxygen and liquid methane propellants. Oxygen was injected conventionally in the center of the coaxial element, and swirl was provided by tangential entry slots. Injectors with 28-element and 40-element patterns were tested with several configurations of combustion chambers, including ablative and calorimeter spool sections, and several configurations of fuel injection design. Low frequency combustion instability (chug) occurred with both injectors, and high-frequency combustion instability occurred at the first tangential (1T) transverse mode with the 40-element injector. In most tests, a transition between high-amplitude chug with gaseous methane flow and low-amplitude chug with liquid methane flow was readily observed. Chug analyses of both conditions were conducted using techniques from Wenzel and Szuch and from the Rocket Combustor Interactive Design and Analysis (ROCCID) code. The 1T mode instability occurred in several tests and was apparent by high-frequency pressure measurements as well as dramatic increases in calorimeter-measured heat flux throughout the chamber. Analyses of the transverse mode were conducted with ROCCID and empirical methods such as Hewitt d/V. This paper describes the test hardware configurations, test data, analysis methods, and presents results of the various analyses.

Hulka, J. R.↗
NASA NTRS2011

Modelling the Huge, Herschel-Resolved Debris Ring around HD 207129

Debris disks, which are inferred from the observed infrared excess to be ensembles of dust, rocks. and probably planetesimals, arc common features of stellar systems. As the mechanisms of their fonnation and evolution are linked to those of planetary bodies, they provide valuable infonnation. The few well-resolved debris disks are even more valuable because they can serve as modelling benchmarks and help resolve degeneracies in modelling aspects such as typical grain sizes and distances. Here, we present an analysis of the HD 207129 debris disk, based on its well-covered spectral energy distribution and Herschel/PACS images obtained in the framework of the DUNES (DUst around NEarby Stars) programme. We use an empirical power-law approach to the distribution of dust and we then model the production and removal of dust by means of collisions, direct radiation pressure, and drag forces. The resulting best-fit model contains a total of nearly 10(sup -2) Earth masses in dust, with typical grain sizes in the planetesimal beh ranging from 4 to 7 micrometers. We constrain the dynamical excitation to be low, which results in very long collisional lifetimes and a drag that notably fills the inner gap, especially at 70 micrometers. The radial distribution stretches from well within 100 AU in an unusual, outward-riSing slope towards a rather sharp outer edge at about 170-190 AU. The inner edge is therefore smoother than that reported for Fomalhaut, but the contribution from the extended halo of barely bound grains is similarly small. Both slowly self-stirring and planetary perturbations could potentially have formed and shaped this disk.

Lohne, T.↗
DOE OSTI2022

Computing Thermodynamic Properties of Fluids Augmented by Nanoconfinement: Application to Pressurized Methane

Nanoconfined fluids exhibit remarkably different thermodynamic behavior compared to the bulk phase. These confinement effects render predictions of thermodynamic quantities of nanoconfined fluids challenging. In particular, confinement creates a spatially varying density profile near the wall that is primarily responsible for adsorption and capillary condensation behavior. Significant fluctuations in thermodynamic quantities, inherent in such nanoscale systems, coupled to strong fluid–wall interactions give rise to this near-wall density profile. Empirical models have been proposed to explain and model these effects, yet no first-principles based formulation has been developed. We present a statistical mechanics framework that embeds such a coupling to describe the effect of the fluid–wall interaction in amplifying the near-wall density behavior for compressible gases at elevated pressures such as pressurized methane in confinement. We show that the proposed theory predicts accurately the adsorbed layer thickness as obtained with small-angle neutron scattering measurements. Furthermore, the predictions of density under confinement from the proposed theory are shown to be in excellent agreement with available experimental and atomistic simulations data for a range of temperatures for nanoconfined methane. While the framework is presented for evaluating the near-wall density, owing to its rigorous foundation in statistical mechanics, the proposed theory can also be generalized for predicting phase-transition and nonequilibrium transport of nanoconfined fluids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Use of the Jacchia /1977/ empirical model in a dynamical model of upper-atmospheric helium

This brief report describes an investigation of the effects of using the Jacchia (1977) model in place of the Jacchia (1971) model for specifying the background gas pressure in the theoretical model of thermospheric helium described by Straus, et al. (1977). Changes in the global transport of helium caused by a small increase in the latitudes at which the background gas pressure extrema occur lead to much better agreement of the model predictions with data taken by the mass spectrometers on board the Esro 4 and OGO 6 satellites.

Straus, J. M.↗
NASA NTRS1981

Empirical model of the interaction of the solar wind with the daytime ionosphere of Venus

Interplanetary probe data on the interaction of the solar wind with the ionosphere of Venus are examined. It is shown that the ionospheric pressure above the ionopause is approximately equal to the dynamic pressure of the solar wind, while the value of magnetic pressure at the ionopause amounts to about 2/3 of the value of external and ionospheric pressures. A first-approximation model is proposed for changes of pressure at the ionopause as a function of height and solar zenith angle. This model makes it possible to determine the 'instantaneous' profile of the ionopause for a given solar-wind pressure.

Vaisberg, O. L.↗
NASA NTRS2014

Probabilistic Assessment of Hypobaric Decompression Sickness Treatment Success

The Hypobaric Decompression Sickness (DCS) Treatment Model links a decrease in computed bubble volume from increased pressure (DeltaP), increased oxygen (O2) partial pressure, and passage of time during treatment to the probability of symptom resolution [P(symptom resolution)]. The decrease in offending volume is realized in 2 stages: a) during compression via Boyle's Law and b) during subsequent dissolution of the gas phase via the O2 window. We established an empirical model for the P(symptom resolution) while accounting for multiple symptoms within subjects. The data consisted of 154 cases of hypobaric DCS symptoms along with ancillary information from tests on 56 men and 18 women. Our best estimated model is P(symptom resolution) = 1 / (1+exp(-(ln(Delta P) - 1.510 + 0.795×AMB - 0.00308×Ts) / 0.478)), where (DeltaP) is pressure difference (psid), AMB = 1 if ambulation took place during part of the altitude exposure, otherwise AMB = 0; and where Ts is the elapsed time in mins from start of the altitude exposure to recognition of a DCS symptom. To apply this model in future scenarios, values of DeltaP as inputs to the model would be calculated from the Tissue Bubble Dynamics Model based on the effective treatment pressure: (DeltaP) = P2 - P1 | = P1×V1/V2 - P1, where V1 is the computed volume of a spherical bubble in a unit volume of tissue at low pressure P1 and V2 is computed volume after a change to a higher pressure P2. If 100% ground level O2 (GLO) was breathed in place of air, then V2 continues to decrease through time at P2 at a faster rate. This calculated value of (DeltaP then represents the effective treatment pressure at any point in time. Simulation of a "pain-only" symptom at 203 min into an ambulatory extravehicular activity (EVA) at 4.3 psia on Mars resulted in a P(symptom resolution) of 0.49 (0.36 to 0.62 95% confidence intervals) on immediate return to 8.2 psia in the Multi-Mission Space Exploration Vehicle. The P(symptom resolution) increased to near certainty (0.99) after 2 hrs of GLO at 8.2 psia or with less certainty on immediate pressurization to 14.7 psia [0.90 (0.83 - 0.95)]. Given the low probability of DCS during EVA and the prompt treatment of a symptom with guidance from the model, it is likely that the symptom and gas phase will resolve with minimum resources and minimal impact on astronaut health, safety, and productivity.

Conkin, Johnny↗
NASA NTRS1992

Dynamic response of induced pressures, suckdown, and temperatures for two tandem jet STOVL configurations

NASA Ames Research Center has been conducting a program to improve the methods for predicting the jet-induced lift loss (suckdown) and hot gas ingestion on jet Short Takeoff and Vertical Landing (STOVL) aircraft during hover near the ground. As part of that program, small-scale hover tests were conducted to expand the current data base and to improve upon the current empirical methods for predicting jet-induced lift loss and hot gas ingestion (HGI) effects. This report is one of three data reports covering data obtained from hover tests conducted at Lockheed Aeronautical Systems, Rye Canyon Facility. It will include dynamic (time dependent) test data for both lift loss and HGI parameters (height, nozzle temperature, nozzle pressure ratio, and inlet location). The flat plate models tested were tandem jet configurations with three planform variations and variable position side-by-side sucking inlets mounted above the planform. Temperature time lags from 8-15 seconds were observed before the model temperatures stabilize. This was larger than the expected 1.5-second lag calculated from literature. Several possible explanations for the flow temperatures to stabilize may include some, or all, of the following: thermocouple lag, radiation to the model surface, and heat loss to the ground board. Further investigations are required to understand the reasons for this temperature lag.

Wardwell, Douglas A.↗
NASA NTRS1974

Physical properties of solar chromospheric plages. II - Chromospheric plage models

Chromospheric models of plages are proposed to explain profiles of the Ca II H, K, 8498-A, 8542-A, and 8662-A lines. These models are consistent with boundary conditions imposed by the photosphere and the Lyman continuum. It is found that increasing emission in these lines is consistent with a picture of increasing temperature gradient in the low chromosphere and the resulting increase in pressure and electron density at similar line optical depths. With this picture it is shown how the distribution of chromospheric parameters across the solar disk can be empirically determined directly from Ca II filtergrams. It is also proposed that the high-density aspects of solar activity are produced by steep temperature gradients in the low chromosphere and thus by the enhanced heating mechanisms that steepen these gradients.

Shine, R. A.↗
NASA NTRS1981

Turbulent jet patterns in accelerating flows

Results of flow visualization experiments, and a semi-empirical model of a single turbulent jet injected perpendicularly to a different density cross flow are presented. The model is based on integral conservation equations, including the pressure terms appropriate to accelerating flow. It uses an entrainment correlation obtained from previous experiments of a jet in a cross stream. The results show trajectories and spreading rates, and are typified by a set of three parameters: momentum ratio, Froude number and density ratio. Agreement between test and calculated results is encouraging, but tend to be poorer with increasing momentum ratio.

Lipshitz, A.↗
NASA NTRS1986

Thermofluid analysis of the SSME preburner using a gas-gas diffusion model for oxygen and hydrogen combustion at supercritical pressures

The paper discusses the thermofluid analysis of the Space Shuttle Main Engine (SSME) fuelside preburner. The governing equations have been solved numerically to predict flow, heat transfer, mixing, and combustion. A two-fluid approach is adopted in which oxygen is regarded as one fluid and hydrogen is regarded as the other fluid. The chemical kinetics is assumed to be very fast so that combustion is primarily controlled by the rate of mixing between oxygen and hydrogen. The preburner pressure is much greater than the critical pressures of oxygen and hydrogen; hence, a gas-gas diffusion model (rather than an evaporation model) has been developed to compute the rate of interphase mixing. Empirical correlations have been incorporated to account for the effect of slip on the interphase exchange. A sensitivity study has been performed with various model parameters. It is observed that the model can predict possibility of incomplete combustion and local regions of high temperatures under steady operating conditions. Some of these anomalies have been observed in actual tests, and the numerical model is useful for understanding possible causes and remedies. At least some measurements are needed for quantitative verification of the model.

Prakash, C.↗
NASA NTRS1990

Tank Pressure Control Experiment - A low-g mixing investigation

The Tank Pressure Control Experiment (TPCE) was conceived to meet the need for an aspect of cryogenic fluid management technology that is critical to several future national space missions: control of cryogenic storage tank pressures by active mixing. In-space testing is the only means of obtaining the fluid dynamic data necessary to develop and test predictive models of mixing. These models, when validated, will allow future cryogenic systems to be designed with more efficient and reliable pressure control systems. The objectives of the TPCE project are to characterize the fluid dynamics of jet-induced mixing in low gravity, evaluate the validity of empirical models and correlations, and provide data for use in developing and validating computational fluid dynamic models. This paper discusses prior studies of low-g mixing, the objectives and benefits of TPCE, the design and status of the payload, and preliminary results obtained from low-g aircraft testing.

Bentz, M. D.↗
NASA NTRS1989

Understanding transition and turbulence through direct simulations

Direct simulations consist in solving the full Navier-Stokes equations, without any turbulence model, and describing all the detailed features of the flow. Usually the flows are three-dimensional and time-dependent and contain both coarse and fine structures, which makes the numerical task very challenging in terms of both the algorithm and the computational effort. Most of the work until now has involved spectral methods, which are highly accurate but not very flexible in terms of geometry or complex equations. For that reason, future work will also rely on high-order finite-difference or other methods. Direct simulations complement experimental work, and both contribute to the theory and the empirical knowledge of turbulence. Once such a simulation has been shown to be accurate, the flow field is completely known in three dimensions and time, including the pressure, the vorticity and any other quantity. On the other hand, most simulations to date solved the incompressible equations in rather simple geometries, and direct simulations will always be limited to moderate Reynolds numbers. Extensive simulations have been conducted in homogeneous turbulence, channel flows, boundary layers, and mixing layers. Much effort is devoted to addressing flows with compressibility and chemical reactions, and to new geometries such as a backward-facing step.

Spalart, P. R.↗
NASA NTRS2011

A Fully Nonlinear, Dynamically Consistent Numerical Model for Solid-Body Ship Motion. I. Ship Motion with Fixed Heading

In this paper, we describe the details of our numerical model for simulating ship solidbody motion in a given environment. In this model, the fully nonlinear dynamical equations governing the time-varying solid-body ship motion under the forces arising from ship wave interactions are solved with given initial conditions. The net force and moment (torque) on the ship body are directly calculated via integration of the hydrodynamic pressure over the wetted surface and the buoyancy effect from the underwater volume of the actual ship hull with a hybrid finite-difference/finite-element method. Neither empirical nor free parametrization is introduced in this model, i.e. no a priori experimental data are needed for modelling. This model is benchmarked with many experiments of various ship hulls for heave, roll and pitch motion. In addition to the benchmark cases, numerical experiments are also carried out for strongly nonlinear ship motion with a fixed heading. These new cases demonstrate clearly the importance of nonlinearities in ship motion modelling.

Lin, Ray-Quing↗
NASA NTRS2017

The Substorm Cycle as Reproduced by Global MHD Models

Recently, Gordeev et al. (2015) suggested a method to test global MHD models against statistical empirical data. They showed that four community-available global MHD models supported by the Community Coordinated Modeling Center (CCMC) produce a reasonable agreement with reality for those key parameters (the magnetospheric size, magnetic field, and pressure) that are directly related to the large-scale equilibria in the outer magnetosphere. Based on the same set of simulation runs, here we investigate how the models reproduce the global loading-unloading cycle. We found that in terms of global magnetic flux transport, three examined CCMC models display systematically different response to idealized2 h north then 2 h south interplanetary magnetic field (IMF) Bz variation. The LFM model shows a depressed return convection and high loading rate during the growth phase as well as enhanced return convection and high unloading rate during the expansion phase, with the amount of loaded unloaded magnetotail flux and the growth phase duration being the closest to their observed empirical values during isolated substorms. Two other models exhibit drastically different behavior. In the BATS-R-US model the plasma sheet convection shows a smooth transition to the steady convection regime after the IMF southward turning. In the Open GGCM a weak plasma sheet convection has comparable intensities during both the growth phase and the following slow unloading phase. We also demonstrate potential technical problem in the publicly available simulations which is related to post processing interpolation and could affect the accuracy of magnetic field tracing and of other related procedures.

Gordeev, E.↗
NASA NTRS1977

Fluid mechanical model of the Helmholtz resonator

A semi-empirical fluid mechanical model of the acoustic behavior of Helmholtz resonators is presented which predicts impedance as a function of the amplitude and frequency of the incident sound pressure field and resonator geometry. The model assumes that the particle velocity approaches the orifice in a spherical manner. The incident and cavity sound fields are connected by solving the governing oscillating mass and momentum conservation equations. The model is in agreement with the Rayleigh slug-mass model at low values of incident sound pressure level. At high values, resistance is predicted to be independent of frequency, proportional to the square root of the amplitude of the incident sound pressure field, and virtually independent of resonator geometry. Reactance is predicted to depend in a very complicated way upon resonator geometry, incident sound pressure level, and frequency. Nondimensional parameters are defined that divide resonator impedance into three categories corresponding to low, moderately low, and intense incident sound pressure amplitudes. The two-microphone method was used to measure the impedance of a variety of resonators. The data were used to refine and verify the model.

Hersh, A. S.↗
NASA NTRS1977

Volatile/mobile trace elements in Karoonda /C4/ chondrite

Concentrations of ten volatile/mobile trace elements and of nonvolatile Co in the Karoonda (C4) meteorite were determined, and the atomic abundances relative to C1 are compared with values for the Murchison (C2) and Allende (C3) meteorites. Empirical Bi, In, and Tl data for Karoonda and heated Allende and Murchison are compared with theoretical curves for condensation from a gas of cosmic composition at low pressures. It is suggested that Karoonda might derive from low-temperature open-system metamorphism of pristine C3-like material.

Matza, S. D.↗
NASA NTRS1978

A vortex model for transport in the polar stratosphere

A semi-empirical model based on a Gaussian vorticity distribution was developed for determining eddy diffusivity and wind transport distributions in the polar stratosphere. The model uses as input data pressure surface heights measured at periods of the year when the stratospheric polar vortex exhibits nearly circular patterns around the pole. The components of the polar wind velocities that result from a Prandtl eddy viscosity distribution are found to be in general agreement with those obtained by other investigators.

Eberstein, I. J.↗