MESUR Pathfinder Microrover Flight Experiment: A Better, Faster, Cheaper Rover
This paper describes MFEX and the four factors that contribute to the feasibility of small rovers.
Mars Environmental Survey (MESUR) MESUR Pathfinder↗
SEARCH · Search NASA
Results for “flight experiments”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of the Lens Antenna Deployment Demonstration (LADD) shuttle-attached flight experiment
The primary objective of the LADD Program is to develop a technology demonstration test article that can be used for both ground and flight tests to demonstrate the structural and mechanical feasibility and reliability of the single-axis roll-out space based radar (SBR) approach. As designed, the LADD will essentially be a generic strucutural experiment which incorporates all critical technology elements of the operational satellite and is applicable to a number of future antenna systems. However, to fully determine its design integrity for meeting the lens flatness and constant geometry requirements in a zero g environment under extreme thermal conditions, the LADD must be space flight tested. By accurately surveying the structure under varying conditions the membrane tolerance-holding capabilities of the structure will be demonstrated. The flight test will provide data to verify analytical tools used to predict thermal and structural behavior. Most important, the experiment will provide an initial indication of structural damping in a zero g vacuum environment. The recently completed Solar Array Flight Experiment (SAFE) showed orbital damping greater than that experienced during ground testing. From the experience and the information obtained from LADD it is hoped that designs can be confidently extrapolated to operational satellites with apertures in the 20 m by 60 m size range.
Hill, H.↗
Spacecraft Autonomy Flight Experience: The DS1 Remote Agent Experiment
In May 1999 state-of-the-art autonomy technology was allowed to assume command and control of the Deep Space One spacecraft during the Remote Agent Experiment.
Autonomy↗
Results of a flight experiment on the catalytic efficiency of the Space Shuttle heat shield
An experiment was performed on the second Space Shuttle flight to verify data from arc-heated wind-tunnel tests indicating that the thermal protection tiles used on the Shuttle's surface are noncatalytic to the recombination of dissociated air. The experiment indicates that the tiles are indeed noncatalytic, and explains the lower than expected temperatures observed in the first two Shuttle flights. The data are reasonably well predicted with computations, using a chemically reactive boundary-layer code. The experimental setup and the computational analysis are described.
Rakich, J. V.↗
Spacecraft Autonomy Flight Experience: The DS1 Remote Agent Experiment
In May 1999 state-of-the-art autonomy technology was allowed to assume command and control of the Deep Space One spacecraft during the Remote Agent Experiment.
Autonomy↗
A study of voltage breakdown in spacecraft systems from test and flight experience
Voltage breakdown in spacecraft electronic circuitry during tests and flight conditions
Mercy, K. R.↗
Free molecule drag and lift deduced from Shuttle flight experiment
A gas surface interaction experiment was flown on the STS-8 flight of the Space Shuttle in which atomic oxygen was allowed to reflect off a glassy carbon surface. The spatial distribution of the reflected molecules was recorded showing a lobe between the specular and normal directions. Using the Nocilla treatment of the reflected molecules, the speed ratio of the reflected molecules and the angle of the drifting velocity with respect to the surface were determined. This information is used to determine the drag coefficient of a sphere and the drag and lift coefficients of a flat plate.
Karr, Gerald R.↗
Numerical simulation of hypersonic flow over an aeroassist flight experiment vehicle
Solutions of wind-tunnel and entry-flight flow around the vehicle are obtained from the Navier-Stokes equations coupled with the chemical species continuity equations if needed. The time-iterative method employs several techniques: shock fitting, chemistry-split ADI and an algebraic grid in conformal spherical-polar space. Sensitivities of the results to numerical parameters and to frozen, equilibrium and finite rate reactions are investigated in the forebody computation. Quantitative results are obtained for the shock layer and the near wake for the entire vehicle corresponding to both ground test and flight conditions. Complex flow characteristics are analyzed on the basis of the complete flowfield over the aerobrake and simplified afterbodies. The method is stable and cost effective, and has yielded shock locations and wall pressure distributions which are in good agreement with wind-tunnel data.
Li, C. P.↗
Shuttle Orbiter Environmental Control and Life Support System - Flight experience
This paper describes the overall design of the Shuttle Orbiter Environmental Control and Life Support System (ECLSS). The Orbiter ECLSS consists of six major subsystems which accomplish the functions of providing a habitable pressurized cabin atmosphere and removing gaseous contaminants, controlling the temperature of the cabin and vehicle components within acceptable ranges, providing fire detection and suppression capability, maintaining a supply of potable water, collecting and removing metabolic waste materials, and providing utilities and access for extravehicular activity. The operational experience is summarized for the 45 space flights accomplished to date during which the Orbiter ECLSS has been demonstrated to perform reliably, and has proved to have the flexibility to meet a variety of mission needs. Significant flight problems are described, along with the design or procedure changes which were implemented to resolve the problems.
Winkler, H. E.↗
Advanced IR System For Supersonic Boundary Layer Transition Flight Experiment
Infrared thermography is a preferred method investigating transition in flight: a) Global and non-intrusive; b) Can also be used to visualize and characterize other fluid mechanic phenomena such as shock impingement, separation etc. F-15 based system was updated with new camera and digital video recorder to support high Reynolds number transition tests. Digital Recording improves image quality and analysis capability and allows for accurate quantitative (temperature) measurements and greater enhancement through image processing allows analysis of smaller scale phenomena.
Banks, Daniel W.↗
Lunar Reconnaissance Orbiter (LRO) Thruster Control Mode Design and Flight Experience
National Aeronautics and Space Administration s (NASA) Goddard Space Flight Center (GSFC) in Greenbelt, MD, designed, built, tested, and launched the Lunar Reconnaissance Orbiter (LRO) from Cape Canaveral Air Force Station on June 18, 2009. The LRO spacecraft is the first operational spacecraft designed to support NASA s return to the Moon, as part of the Vision for Space Exploration. LRO was launched aboard an Atlas V 401 launch vehicle into a direct insertion trajectory to the Moon. Twenty-four hours after separation the propulsion system was used to perform a mid-course correction maneuver. Four days after the mid-course correction a series of propulsion maneuvers were executed to insert LRO into its commissioning orbit. The commission period lasted eighty days and this followed by a second set of thruster maneuvers that inserted LRO into its mission orbit. To date, the spacecraft has been gathering invaluable data in support of human s future return to the moon. The LRO Attitude Control Systems (ACS) contains two thruster based control modes: Delta-H and Delta-V. The design of the two controllers are similar in that they are both used for 3-axis control of the spacecraft with the Delta-H controller used for momentum management and the Delta-V controller used for orbit adjust and maintenance maneuvers. In addition to the nominal purpose of the thruster modes, the Delta-H controller also has the added capability of performing a large angle slew maneuver. A suite of ACS components are used by the thruster based control modes, for both initialization and control. For initialization purposes, a star tracker or the Kalman Filter solution is used for providing attitude knowledge and upon entrance into the thruster based control modes attitude knowledge is provided via rate propagation using a inertial reference unit (IRU). Rate information for the controller is also supplied by the IRU. Three-axis control of the spacecraft in the thruster modes is provided by eight 5-lbf class attitude control thrusters configured in two sets of four thrusters for redundancy purposes. Four additional 20-lbf class thrusters configured in two sets of two thrusters are used for Lunar Orbit Insertion maneuvers. The propulsion system is one the few systems on-board the LRO spacecraft that has built in redundancy. The Delta-H controller consists of a Proportional-Derivative (PD) controller with a structural filter on the thrusters and a Proportional controller on the reaction wheels. The PD control that employs the thrusters is used for attitude and rate control. The Proportional controller on the reaction wheels is used for commanding the wheels to a new momentum state. The ground commands used for the Delta-H controller are the system momentum vector, reaction wheel momentum, maximum expected command time, and which set of attitude control thrusters to use. The ability to command both the system momentum vector and reaction wheel momentum in the Delta-H controller provides both a capability and an additional source of operator error. Large angle slews via the Delta-H controller is achievable via this commands because these commands are used for the exit mode criteria. Setting these commands to non-consistent values prevents the mode from exiting nominally.
Hsu, Oscar C.↗
Flight experiments measuring boundary-layer disturbances in laminar flow and correlation with stability analysis
Flight test results are reported from an experiment designed to study the detailed growth of disturbances in the laminar boundary layer. A gloved wing section incorporating closely-spaced flush-mounted streamwise-located instrumentation for measuring instability frequencies and amplitude growths as well as pressure distributions was used. The growth of Tollmien-Schlichting (T-S) and crossflow instabilities is predicted by the linear e exp n method and compared to the measured boundary-layer disturbance frequencies. The predictions showed good agreement with the measured data. The results exhibited fair agreement with previous n(T-S) and n(CF) flight correlations for several of the conditions analyzed. It is inferred from the high n(T-S) values for these data that moderately swept wings at compressible speeds can withstand higher combinations of n(T-S) and n(CF) values and still remain laminar than previously thought.
Lee, Cynthia C.↗
Laser Beam Welding for in-Space Joining Demonstrated Under Vacuum on the Ground and By Parabolic Flight Experiments
High energy density electron beam welding enabled the first and, to date, only American weld performed in space during the M551 experiment on Skylab in 1973. Though welding is critical to 90% of durable goods manufacturing in America, there is not yet regular and reliable application of welding processes to the In-space Servicing, Assembly, and Manufacturing (ISAM) sector. Fundamental studies are needed to develop basic capabilities and to enhance fundamental process knowledge, which will support follow-on efforts to mature in-space welding for use in commercial, defense, and other aerospace applications. The current work seeks to build on past flights and improve understanding and quantification of materials joining in space conditions using laser beam welding (LBW). LBW offers several advantages over the electron beam welding of Skylab, amongst others: reduced electromagnetic interference, less exposure of operators to ionizing radiation, and flexible delivery through optical fibers supporting unique workpieces and joints. Since there is no orbital laboratory to mature laser beam welding for space, the current effort addresses maturation of laser beam welding through parabolic flights augmented with data collection to enable numerical modeling efforts that capture the physical effects of the space environment. This team has retrofitted an LBW experimental apparatus that can simulate the vacuum and, during a parabolic flight, the reduced gravity & microgravity conditions of in-space welding. A team of Capstone students modified the setup, originally developed by NASA Langley Research Center for electron beam free-form fabrication, to replace its electron gun with a 1 kW, 1070 nm Yb fiber laser. The apparatus was further instrumented with temperature sensing and high-speed welding cameras to monitor and record changes in the thermal state of the workpiece, the melt pool, the laser penetration level, and the development and orientation of spatter & plumes. The system will operate autonomously, demonstrating its utility to uncrewed missions. During upcoming parabolic flight campaigns expected summer 2024, this LBW equipment will weld common aerospace alloys of aluminum, stainless steel, and titanium under conditions representative of the space environment. This data will guide future computational modeling efforts of laser welding in space and help to qualify in-space welding as a viable ISAM technique.
laser beam welding↗
STS-40 orbital acceleration research experiment flight results during a typical sleep period
The Orbital Acceleration Research Experiment (OARE), an electrostatic accelerometer package with complete on-orbit calibration capabilities was flown aboard Shuttle on STS-40. The instrument is designed to measure and record the Shuttle aerodynamic acceleration environment from the free molecule flow regime through the rarefied flow transition into the hypersonic continuum regime. Because of its sensitivity, the OARE instrument detects aerodynamic behavior of the Shuttle while in low-earth orbit. A 2-h orbital time period on day seven of the mission, when the crew was asleep and other spacecraft activities were at a minimum, was examined. Examination of the model with the flight data shows the instrument to be sensitive to all major expected low-frequency acceleration phenomena; however, some erratic instrument bias behavior persists in two axes. In these axes, the OARE data can be made to match a comprehensive atmospheric-aerodynamic model by making bias adjustments and slight liner corrections for drift.
Blanchard, Robert C.↗
STS-40 orbital acceleration research experiment flight results during a typical sleep period
The Orbital Acceleration Research Experiment (OARE), an electrostatic accelerometer package with complete on-orbit calibration capabilities, was flown for the first time aboard the Space Shuttle on STS-40. This is also the first time an accelerometer package with nano-g sensitivity and a calibration facility has flown aboard the Space Shuttle. The instrument is designed to measure and record the Space Shuttle aerodynamic acceleration environment from the free molecule flow regime through the rarified flow transition into the hypersonic continuum regime. Because of its sensitivity, the OARE instrument defects aerodynamic behavior of the Space Shuttle while in low-earth orbit. A 2-hour orbital time period on day seven of the mission, when the crew was asleep and other spacecraft activities were at a minimum, was examined. During the flight, a 'trimmed-mean' filter was used to produce high quality, low frequency data which was successfully stored aboard the Space Shuttle in the OARE data storage system. Initial review of the data indicated that, although the expected precision was achieved, some equipment problems occurred resulting in uncertain accuracy. An acceleration model which includes aerodynamic, gravity-gradient, and rotational effects was constructed and compared with flight data. Examination of the model with the flight data shows the instrument to be sensitive to all major expected low frequency acceleration phenomena; however, some erratic instrument bias behavior persists in two axes. In these axes, the OARE data can be made to match a comprehensive atmospheric-aerodynamic model by making bias adjustments and slight linear corrections for drift. The other axis does not exhibit these difficulties and gives good agreement with the acceleration model.
Blanchard, R. C.↗
Supersonic Boundary Layer Transition Flight Experiment
A history and status of the "Supersonic Boundary Layer Transition" flight test program.
Banks, Daniel W.↗
Visual Earth observation performance in the space environment. Human performance measurement 4: Flight experiments
A wide variety of secondary payloads have flown on the Space Transportation System (STS) since its first flight in the 1980's. These experiments have typically addressed specific issues unique to the zero-gravity environment. Additionally, the experiments use the experience and skills of the mission and payload specialist crew members to facilitate data collection and ensure successful completion. This paper presents the results of the Terra Scout experiment, which flew aboard STS-44 in November 1991. This unique Earth Observation experiment specifically required a career imagery analyst to operate the Spaceborne Direct-View Optical System (SpaDVOS), a folded optical path telescope system designed to mount inside the shuttle on the overhead aft flight deck windows. Binoculars and a small telescope were used as backup optics. Using his imagery background, coupled with extensive target and equipment training, the payload specialist was tasked with documenting the following: (1) the utility of the equipment; (2) his ability to acquire and track ground targets; (3) the level of detail he could discern; (4) the atmospheric conditions; and (5) other in-situ elements which contributed to or detracted from his ability to analyze targets. Special emphasis was placed on the utility of a manned platform for research and development of future spaceborne sensors. The results and lessons learned from Terra Scout will be addressed including human performance and equipment design issues.
Huth, John F.↗
Aerodynamic stability and heating analyses for the aeroassist flight experiment vehicle
Since ground based flow simulations are presently unable to model flight conditions expected for AOTVs (Aeroassist Orbital Transfer Vehicle) and other hypersonic space vehicles, computer codes are being developed to provide design parameters necessary for structure, guidance, and control aspects. Over the past four years, VRFLO (Viscous Reactive Flow) has been written to model finite-rate chemistry and viscous effects for a variety of aerobrake bodies. VRFLO includes a number of unique features that are summarized as follows: (1) Grid generation is an integral part of the code for several aerobrake configurations which includes the wake flow region; (2) The formulation is valid for three air chemical models; (3) An ADI central difference technique is used to solve the Navier-Stokes and species continuity equations in split groups; and (4) Grid density and numerical damping are minimized by shock-fitting and conformal mapping of body points.
Mcgary, J.↗