Results for “flow solver” — Page 23

NASA NTRS1996

Development of a Driver Code for the WICS Project

Wall Interference Correction System (WICS) is a computational technique to evaluate the wind tunnel wall interference corrections for blockage, Mach number, dynamic pressure and angle of attack. The objective is to predict the effects of the bounding walls on wind tunnel measurements [1]. The procedure attempts to compute these corrections in real time so that the test engineer can implement these by adjusting wind tunnel controls for angle of attack and dynamic pressure while the test is in progress in the 12 ft. pressure wind tunnel at the Ames Research Center. The technique utilizes an ideal flow solver PMARC (Panel Method developed at the Ames Research Center) to compute influence coefficients in an internal flow mode by representing a paneled model of the tunnel for fullspan and semispan tests.

Ghosh, Amitabha↗

NASA NTRS2003

Wind-US Flow Calculations for the M2129 S-Duct Using Structured and Unstructured Grids

Computational Fluid Dynamics (CFD) flow solutions for the M2129 diffusing S-duct with and without vane effectors were computed by the Wind-US flow solver. Both structured and unstructured 3-D grids were used. Without vane effectors, the duct exhibited massive flow separation in both experiment and CFD. With vane effectors installed, the flow remained attached and aerodynamic losses were reduced. Total pressure recovery and distortion near the duct outlet were computed from the solutions and compared favorably to experimental values. These calculations are part of a validation effort for the Wind-US code. They also provide an example case to aid engineers in learning to use the Wind-US software.

Mohler, Stanley R., Jr.↗

NASA NTRS2012

Numerical Simulation of Rocket Exhaust Interaction with Lunar Soil

This technology development originated from the need to assess the debris threat resulting from soil material erosion induced by landing spacecraft rocket plume impingement on extraterrestrial planetary surfaces. The impact of soil debris was observed to be highly detrimental during NASA s Apollo lunar missions and will pose a threat for any future landings on the Moon, Mars, and other exploration targets. The innovation developed under this program provides a simulation tool that combines modeling of the diverse disciplines of rocket plume impingement gas dynamics, granular soil material liberation, and soil debris particle kinetics into one unified simulation system. The Unified Flow Solver (UFS) developed by CFDRC enabled the efficient, seamless simulation of mixed continuum and rarefied rocket plume flow utilizing a novel direct numerical simulation technique of the Boltzmann gas dynamics equation. The characteristics of the soil granular material response and modeling of the erosion and liberation processes were enabled through novel first principle-based granular mechanics models developed by the University of Florida specifically for the highly irregularly shaped and cohesive lunar regolith material. These tools were integrated into a unique simulation system that accounts for all relevant physics aspects: (1) Modeling of spacecraft rocket plume impingement flow under lunar vacuum environment resulting in a mixed continuum and rarefied flow; (2) Modeling of lunar soil characteristics to capture soil-specific effects of particle size and shape composition, soil layer cohesion and granular flow physics; and (3) Accurate tracking of soil-borne debris particles beginning with aerodynamically driven motion inside the plume to purely ballistic motion in lunar far field conditions. In the earlier project phase of this innovation, the capabilities of the UFS for mixed continuum and rarefied flow situations were validated and demonstrated for lunar lander rocket plume flow impingement under lunar vacuum conditions. Applications and improvements to the granular flow simulation tools contributed by the University of Florida were tested against Earth environment experimental results. Requirements for developing, validating, and demonstrating this solution environment were clearly identified, and an effective second phase execution plan was devised. In this phase, the physics models were refined and fully integrated into a production-oriented simulation tool set. Three-dimensional simulations of Apollo Lunar Excursion Module (LEM) and Altair landers (including full-scale lander geometry) established the practical applicability of the UFS simulation approach and its advanced performance level for large-scale realistic problems.

Liever, Peter↗

NASA NTRS2012

Motion Imagery and Robotics Application (MIRA): Standards-Based Robotics

This technology development originated from the need to assess the debris threat resulting from soil material erosion induced by landing spacecraft rocket plume impingement on extraterrestrial planetary surfaces. The impact of soil debris was observed to be highly detrimental during NASA s Apollo lunar missions and will pose a threat for any future landings on the Moon, Mars, and other exploration targets. The innovation developed under this program provides a simulation tool that combines modeling of the diverse disciplines of rocket plume impingement gas dynamics, granular soil material liberation, and soil debris particle kinetics into one unified simulation system. The Unified Flow Solver (UFS) developed by CFDRC enabled the efficient, seamless simulation of mixed continuum and rarefied rocket plume flow utilizing a novel direct numerical simulation technique of the Boltzmann gas dynamics equation. The characteristics of the soil granular material response and modeling of the erosion and liberation processes were enabled through novel first principle-based granular mechanics models developed by the University of Florida specifically for the highly irregularly shaped and cohesive lunar regolith material. These tools were integrated into a unique simulation system that accounts for all relevant physics aspects: (1) Modeling of spacecraft rocket plume impingement flow under lunar vacuum environment resulting in a mixed continuum and rarefied flow; (2) Modeling of lunar soil characteristics to capture soil-specific effects of particle size and shape composition, soil layer cohesion and granular flow physics; and (3) Accurate tracking of soil-borne debris particles beginning with aerodynamically driven motion inside the plume to purely ballistic motion in lunar far field conditions.

Martinez, Lindolfo↗

NASA NTRS2015

LEWICE3D/GlennHT Particle Analysis of the Honeywell Al502 Low Pressure Compressor

A flow and ice particle trajectory analysis was performed for the booster of the Honeywell AL502 engine. The analysis focused on two closely related conditions one of which produced a rollback and another which did not rollback during testing in the Propulsion Systems Lab at NASA Glenn Research Center. The flow analysis was generated using the NASA Glenn GlennHT flow solver and the particle analysis was generated using the NASA Glenn LEWICE3D v3.56 ice accretion software. The flow and particle analysis used a 3D steady flow, mixing plane approach to model the transport of flow and particles through the engine. The inflow conditions for the rollback case were: airspeed, 145 ms; static pressure, 33,373 Pa; static temperature, 253.3 K. The inflow conditions for the non-roll-back case were: airspeed, 153 ms; static pressure, 34,252 Pa; static temperature, 260.1 K. Both cases were subjected to an ice particle cloud with a median volume diameter of 24 microns, an ice water content of 2.0 gm3 and a relative humidity of 100 percent. The most significant difference between the rollback and non-rollback conditions was the inflow static temperature which was 6.8 K higher for the non-rollback case.

Ice Accretion Codes↗

NASA NTRSDate not supplied

Edge-Based Viscous Method for Mixed-Element Node-Centered Finite-Volume Solvers

A novel, efficient, edge-based viscous (EBV) discretization method has been recently developed, implemented in a practical, unstructured-grid, node-centered, finite-volume flow solver, and applied to viscous-kernel computations that include evaluations of meanflow viscous fluxes, turbulence-model and chemistry-model diffusion terms, and the corresponding Jacobian contributions. Initially, the EBV method had been implemented for tetrahedral grids and demonstrated multifold acceleration of all viscous-kernel computations. This paper presents an extension of the EBV method for mixed-element grids. In addition to the primal edges of a given mixed-element grid, virtual edges are introduced to connect cell nodes that are not connected by a primal edge. The EBV method uses an efficient loop over all (primal and virtual) edges and features a compact discretization stencil based on the nearest neighbors. This study verifies the EBV method and assesses its efficiency on mixed-element grids by comparing the EBV solution accuracy and iterative convergence with those of well-established solutions obtained using a cell-based viscous (CBV) discretization method. The EBV solver’s memory footprint is optimized and often smaller than the memory footprint of the CBV solver. A multifold speedup is demonstrated for all viscous-kernel computations resulting in significant reduction of the time to solutions for several benchmark mixed-element-grid computations, including simulations of a flow around NASA’s juncture-flow model and a hypersonic, chemically reacting flow around a blunt body.

CFD↗

NASA NTRSDate not supplied

Edge-Based Viscous Method for Mixed-Element Node-Centered Finite-Volume Solvers

A novel, efficient, edge-based viscous (EBV) discretization method has been recently developed, implemented in a practical, unstructured-grid, node-centered, finite-volume flow solver, and applied to viscous-kernel computations that include evaluations of meanflow viscous fluxes, turbulence-model and chemistry-model diffusion terms, and the corresponding Jacobian contributions. Initially, the EBV method had been implemented for tetrahedral grids and demonstrated multifold acceleration of all viscous-kernel computations. This paper presents an extension of the EBV method for mixed-element grids. In addition to the primal edges of a given mixed-element grid, virtual edges are introduced to connect cell nodes that are not connected by a primal edge. The EBV method uses an efficient loop over all (primal and virtual) edges and features a compact discretization stencil based on the nearest neighbors. This study verifies the EBV method and assesses its efficiency on mixed-element grids by comparing the EBV solution accuracy and iterative convergence with those of well-established solutions obtained using a cell-based viscous (CBV) discretization method. The EBV solver’s memory footprint is optimized and often smaller than the memory footprint of the CBV solver. A multifold speedup is demonstrated for all viscous-kernel computations resulting in significant reduction of the time to solutions for several benchmark mixed-element-grid computations, including simulations of a flow around NASA’s juncture-flow model and a hypersonic, chemically reacting flow around a blunt body.

Edge-based viscous method↗

NASA NTRSDate not supplied

Wall-Modeled Large Eddy Simulation Method for Unstructured-Grid Navier-Stokes Solvers

This paper reports on the implementation and assessment of a Wall-Modeled Large-Eddy Simulation (WMLES) methodology in an unstructured-grid, node-centered flow solver, FUN3D that is developed and supported at the NASA Langley Research Center. Finite-volume (FV) and finite-element (FE) discretization schemes considered in the study provide formal second-order spatial accuracy. Large-Eddy Simulations (LES) resolve large-scale turbulent-flow features and filter out small-scale effects using the Vreman subgrid-scale model. At solid-wall boundaries, a shear-stress model is employed to provide a proper boundary-flux closure. The nonlinear equations are integrated in time using either an optimized backward difference formula or an implicit multistage Runge-Kutta temporal scheme. The implicit equations at each time step are solved by strong nonlinear iteration schemes. WMLES demonstrations are shown for two high-lift configurations, namely, the McDonnell Douglas 30P30N multielement airfoil and a NASA High-Lift Common Research Model. Results show that the WMLES approaches implemented in the FV and FE discretization methods produce consistent solutions and are capable of capturing key aerodynamic characteristics and flow structures for high-lift configurations at a wide range of angles of attack including maximum-lift conditions. In the 30P30N example, correct trends in the variations of integrated aerodynamic forces and moments, surface pressure distributions, and boundary-layer profiles are captured as the Reynolds number is increased.

CFD; turbulence modeling; High-Lift flow simulatio↗

NASA NTRS2016

Natural Laminar Flow Design for Wings with Moderate Sweep

A new method for the aerodynamic design of wings with natural laminar flow is under development at the NASA Langley Research Center. The approach involves the addition of new flow constraints to an existing knowledge-based design module for use with advanced flow solvers. The uniqueness of the new approach lies in the tailoring of target pressure distributions to achieve laminar flow on transonic wings with leading-edge sweeps and Reynolds numbers typical of current transports. The method is demonstrated on the Common Research Model configuration at critical N-factor levels representative of both flight and high-Reynolds number wind tunnel turbulence levels. The design results for the flight conditions matched the target extent of laminar flow very well. The design at wind tunnel conditions raised some design issues that prompted further improvements in the method, but overall has given promising results.

Campbell, Richard L.↗

NASA NTRS1991

3-D CFD in a day - The laser digitizer project

The computation of airflow over complex configurations requires a complete description of the geometry. This can be obtained from CAD data, from blueprints, or from actual models. In any case, the time required is currently estimated at 4 to 6 months. It is proposed to shorten this time by a factor of 10 to 100 through the use of automated software, a fast, highly parallel computer and a three-dimensional laser digitizer. This device can provide (x,y,z) coordinates of surface points at rates exceeding 14,500/sec. Thus, it is possible to digitize an entire model in a few minutes. The accuracy of measurement on a flat white surface is better than 0.005 inches. Higher accuracy is available at higher cost. This work discusses the challenges which remain to be addressed. In particular, the surface point data need to be converted into a surface description, the surface description needs to be made into a surface grid, and the surface grid used to make a volume grid for the flow solver. Algorithms are kept in place or in mind for all of these problems. Integration of the more mature flow solution and visualization algorithms then allows generation of solution graphics directly from a wind tunnel model.

Merriam, Marshal↗

NASA NTRS2009

Re-evaluation of an Optimized Second Order Backward Difference (BDF2OPT) Scheme for Unsteady Flow Applications

Recent experience in the application of an optimized, second-order, backward-difference (BDF2OPT) temporal scheme is reported. The primary focus of the work is on obtaining accurate solutions of the unsteady Reynolds-averaged Navier-Stokes equations over long periods of time for aerodynamic problems of interest. The baseline flow solver under consideration uses a particular BDF2OPT temporal scheme with a dual-time-stepping algorithm for advancing the flow solutions in time. Numerical difficulties are encountered with this scheme when the flow code is run for a large number of time steps, a behavior not seen with the standard second-order, backward-difference, temporal scheme. Based on a stability analysis, slight modifications to the BDF2OPT scheme are suggested. The performance and accuracy of this modified scheme is assessed by comparing the computational results with other numerical schemes and experimental data.

Vatsa, Veer N.↗

NASA NTRS2017

Computational Design and Analysis of a Transonic Natural Laminar Flow Wing for a Wind Tunnel Model

A natural laminar flow (NLF) wind tunnel model has been designed and analyzed for a wind tunnel test in the National Transonic Facility (NTF) at the NASA Langley Research Center. The NLF design method is built into the CDISC design module and uses a Navier-Stokes flow solver, a boundary layer profile solver, and stability analysis and transition prediction software. The NLF design method alters the pressure distribution to support laminar flow on the upper surface of wings with high sweep and flight Reynolds numbers. The method addresses transition due to attachment line contamination/transition, Gortler vortices, and crossflow and Tollmien-Schlichting modal instabilities. The design method is applied to the wing of the Common Research Model (CRM) at transonic flight conditions. Computational analysis predicts significant extents of laminar flow on the wing upper surface, which results in drag savings. A 5.2 percent scale semispan model of the CRM NLF wing will be built and tested in the NTF. This test will aim to validate the NLF design method, as well as characterize the laminar flow testing capabilities in the wind tunnel facility.

Lynde, Michelle N.↗

NASA NTRSDate not supplied

Wall-Modeled LES of a Swept Wing with Leading-Edge Ice Using LAVA Curvilinear, Unstructured, and Cartesian Solvers

Wall-modeled large-eddy simulation (LES) of a swept wing with leading-edge ice build up is performed using three mesh paradigms and associated flow solvers and compared to experimental results. The study focuses on an 8.9% scale model of the CRM65 swept wing featuring both high-fidelity and smooth leading-edge ice shapes. The assessment is conducted using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework using the three actively supported meshing paradigms in LAVA: structured curvilinear overset, unstructured, andCartesian. For the iced configurations, these paradigms use hybrid body-fitted/source-term immersed-boundary, body-fitted, and ghost-cell immersed-boundary strategies, respectively.The unstructured and Cartesian mesh paradigms are particularly attractive for complex ice shapes as they avoid the manual mesh generation effort associated with the curvilinear approach. For the high-fidelity ice shape, good agreement with the experiment can be obtained with all three strategies; however, the curvilinear method is particularly sensitive to the source-term immersed-boundary timescale and span wise mesh resolution, and the Cartesian implementation is sensitive to the choice of numerical flux. For the smooth ice, larger discrepancies are observed across all methods. However, a mesh refinement study guided by flow visualizations leads to an improved comparison with the experiment that is particularly pronounced for the unstructured mesh paradigm.

TTT↗

DOE OSTI2020

AMR-Wind [SWR-20-85]

AMR-Wind is a massively parallel, block-structured adaptive-mesh, incompressible flow solver for wind turbine and wind farm simulations. The solver is built on top of the AMReX library. AMReX is developed at LBNL , NREL , and ANL as part of the Block-Structured AMR Co-Design Center in DOE's Exascale Computing Project. AMReX library provides the mesh data structures, mesh adaptivity, as well as the linear solvers used for solving the governing equations. The primary applications for AMR-Wind are: performing large-eddy simulations (LES) of atmospheric boundary layer (ABL) flows, simulating wind farm turbine-wake interactions using actuator disk or actuator line models for turbines, and as a background solver when coupled with a near-body solver with overset methodology to perform blade-resolved simulations of multiple wind turbines within a wind farm.

Ananthan, Shreyas↗

DOE OSTI2022

Modeling of the effects of non-equilibrium excitation and electrode geometry on H 2 /air ignition in a nanosecond plasma discharge

In this work, we present the results of two-dimensional modeling of the effects of non-equilibrium excitation and electrode geometry on H 2 /air ignition in a nanosecond plasma discharge. A multiscale adaptive reduced chemistry solver for plasma assisted combustion (MARCS-PAC) based on PASSKEy discharge modeling package and compressible multi-component reactive flow solver ASURF+ is developed and validated. This model is applied to simulate the impact of non-equilibrium plasma excitation and electrode geometry and heat loss on the dynamics of the discharge from streamer to spark and ignition kernel development in a H 2 /air mixture with a pair of cylindrical electrodes. The results show that the plasmagenerated species (N 2 (A), N 2 (B), N 2 (a'), N 2 (C), O( 1 D), O and H) in the spark and afterglow significantly accelerate the ignition kernel development. The increase of discharge voltage at the same total discharge energy promotes the non-equilibrium active species production. It is found that the production of electronically excited species at higher reduced electric field strength is more efficient in enhancing ignition in comparison to the vibrational excitation and heating. Moreover, the 2D simulation clearly reveals that the electric field and active species distribution are highly non-uniform. The streamers are initiated at the sharp outer edges of the negative and positive electrodes by a strong electric field while the electric field is much weaker at the centerline of the electrodes. Furthermore, the simulations reveal that the ignition enhancement is sensitive to the variation of electrode shape, diameter, and gap size due to the changes of electric field distribution and location of streamer formation. A cylindrical electrode produces a larger discharge volume and ignition kernel than the parabolic and spherical electrodes, when the discharge is localized near the axis of the gap. It is found that there is a non-monotonic dependence of ignition kernel size on the electrode diameter and inter-electrode distance. The increase of electrode diameter and gap size above the optimal conditions leads to the reduction of ignition kernel volume, due to the decrease of active species concentration and gas temperature. At a larger electrode surface area and electrode diameter as well as smaller electrode gap size, the heat loss to electrode plays a greater role in reducing the ignition kernel size and slowing ignition kernel development. This work provides insights and guidance to understand the kinetic enhancement of non-equilibrium plasma and the effects of electrode geometries on ignition for the optimization ignitors in advanced engines.

42 ENGINEERING↗

DOE OSTI2021

DNS/LES Study of Representative Wall-Bounded Turbulent Flows using SIERRA/Fuego

This report summarizes a series of SIERRA/Fuego validation efforts of turbulent flow models on canonical wall-bounded configurations. In particular, direct numerical simulations (DNS) and large eddy simulations (LES) turbulence models are tested on a periodic channel, a periodic pipe, and an open jet for which results are compared to the velocity profiles obtained theoretically or experimentally. Velocity inlet conditions for channel and pipe flows are developed for application to practical simulations. To show this capability, LES is performed over complex terrain in the form of two natural hills and the results are compared with other flow solvers. The practical purpose of the report is to document the creation of inflow boundary conditions of fully developed turbulent flows for other LES calculations where the role of inflow turbulence is critical.

42 ENGINEERING↗

NASA NTRS1995

An assessment of unstructured grid technology for timely CFD analysis

An assessment of two unstructured methods is presented in this paper. A tetrahedral unstructured method USM3D, developed at NASA Langley Research Center is compared to a Cartesian unstructured method, SPLITFLOW, developed at Lockheed Fort Worth Company. USM3D is an upwind finite volume solver that accepts grids generated primarily from the Vgrid grid generator. SPLITFLOW combines an unstructured grid generator with an implicit flow solver in one package. Both methods are exercised on three test cases, a wing, and a wing body, and a fully expanded nozzle. The results for the first two runs are included here and compared to the structured grid method TEAM and to available test data. On each test case, the set up procedure are described, including any difficulties that were encountered. Detailed descriptions of the solvers are not included in this paper.

Kinard, Tom A.↗

NASA NTRS2005

Application of a Real-Fluid Turbomachinery Analysis to Rocket Turbopump Geometries

A three-dimensional flow solver has been developed for turbomachinery components utilizing real fluid properties. The code is applicable to both incompressible and compressible flow fields. In this study, the code has been applied to the analysis of inducer and impeller geometries representative of those used in rocket engine applications. The predicted results show good agreement with the available experimental data.

Dorney, Daniel J.↗