Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel blending”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Advanced Engine and Fuel Technologies Annual Progress Report (FY2019)

On behalf of the Vehicle Technologies Office of the U.S. Department of Energy, we are pleased to introduce the Fiscal Year (FY) 2019 Annual Progress Report for the Advanced Engine and Fuel Technologies Program. In support of the Vehicle Technology Office’s goal for future U.S. economic growth, the Program focuses on early-stage research and development to improve understanding of combustion processes, fuel properties, and emissions control technologies, generating knowledge and insight necessary for industry to cost-effectively develop the next generation of engines and fuels. One of the most promising and cost-effective approaches to improving the fuel economy of the U.S. vehicle fleet is to introduce the next generation of higher-efficiency, very-low-emission combustion engines that meet future federal emissions regulations into the passenger and commercial vehicle markets. Advanced fuel formulations that can incorporate non-petroleum-based blending agents could further enhance engine efficiency, reduce greenhouse gas emissions, and provide fuel diversification. Also, innovations in combustion, fuels, emissions control, air control, turbomachinery, and energy recovery could potentially increase fuel economy considerably compared to today’s vehicles. The expected national economic, environmental, and energy security benefits from these next-generation engines and fuels would be significant inasmuch as the majority of vehicles sold over the next several decades will still include an engine. The Program has set the following goals for passenger and commercial vehicle fuel economy improvements. By 2030, increase light-duty engine efficiency to demonstrate 35% improvement in passenger vehicle fuel economy (25% improvement from engine efficiency and 10% from fuel co-optimization) relative to a 2015 baseline vehicle, while meeting the U.S. Environmental Protection Agency Tier 3 Emission and Fuel Standards. By 2030, improve heavy-duty engine efficiency by 35% relative to a 2009 baseline vehicle and identify cost-effective high-performance fuels that can further increase efficiency up to an additional 4%, while meeting prevailing U.S. Environmental Protection Agency emissions standards. The Program utilized advanced combustion processes to increase engine efficiency, resulting in a modeled passenger vehicle fuel economy improvement of 19.4% (over a Model Year 2015 baseline) in FY 2019. This report highlights progress achieved by the Advanced Engine and Fuel Technologies Program during FY 2019. The nature, current focus, and recent progress of the Program are described together with summaries of National Laboratory, industry, and university projects that provide an overview of the exciting work being conducted to address critical technical barriers and challenges to commercializing the next generation of higher-efficiency engine, emissions control, and fuel technologies for passenger and commercial vehicles.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

A small-volume, high-throughput approach for surface tension and viscosity measurements of liquid fuels

An ongoing effort looking at bioblendstocks to function as drop-in replacements or blending components for gasoline has identified a large number of candidate fuels. This work documents an approach for rapid screening of candidate fuels using relatively small sample sizes ($\mathcal{O}(\mu\,{\rm l})$) that targets two key physical properties of liquid fuels—surface tension and viscosity. The approach utilizes shape oscillation dynamics of single droplets generated by a piezo-electric device and their decay over time. Strobed imaging of the oscillation process is used along with image processing, edge detection, and data analysis to capture the decay of the oscillation over time. The time constant of the decay process along with oscillation frequency are then used to estimate viscosity and surface tension using a theory for small amplitude droplet oscillations. Measurements are obtained for primary reference fuels (isooctane and n-heptane) as well as candidate fuels from four bio-derived functional groups of interest. Measurement results for surface tension and viscosity are correlated with literature data as well as measurements from standard reference instruments. The measurement results show that the droplet oscillation based approach is capable of reproducing surface tension and viscosity values for the tested fuels within deviations of 7% and 13% respectively from literature data. Results are obtained using an average of 5 µl per fuel within about 20 s, thus demonstrating a small-volume, high-throughput approach that can be used for screening of candidate bioblendstock fuels.

09 BIOMASS FUELS↗
DOE OSTI2021

Octane Index Applicability over the Pressure-Temperature Domain

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

02 PETROLEUM↗
NASA NTRS1981

Catalytic combustion with incompletely vaporized residual fuel

Catalytic combustion of fuel lean mixtures of incompletely vaporized residual fuel and air was investigated. The 7.6 cm diameter, graded cell reactor was constructed from zirconia spinel substrate and catalyzed with a noble metal catalyst. Streams of luminous particles exited the rector as a result of fuel deposition and carbonization on the substrate. Similar results were obtained with blends of No. 6 and No. 2 oil. Blends of shale residual oil and No. 2 oil resulted in stable operation. In shale oil blends the combustor performance degraded with a reduced degree of fuel vaporization. In tests performed with No. 2 oil a similar effect was observed.

Rosfjord, T. J.↗
DOE OSTI2020

Octane Modeling of Isobutanol Blending into Gasoline

Thirty-four gasoline blendstocks for oxygenate blending were used to create finished gasoline blends with isobutanol content of 12.5 volume percent (vol. %) and 16 vol. %. The gasoline blendstocks and finished fuels were analyzed for octane number (research [RON] and motor [MON]) to determine the effect of blending isobutanol. Volumetric and molar linear blending models were developed to predict finished fuel RON and MON, starting from the properties and composition of the gasoline blendstocks and isobutanol. Results show the molar blending model provided a better fit for the experimental data than the volumetric blending model. The volumetric model was further improved by adding nonlinear terms, improving the error to within ~1 ON. Gasoline blendstock properties impacted the finished fuel RON/MON, with paraffins having a synergistic effect with isobutanol and olefins and aromatics having an antagonistic effect.

10 SYNTHETIC FUELS↗
DOE OSTI2022

Evaluation of Performance Variables to Accelerate the Deployment of Sustainable Aviation Fuels at a Regional Scale

An increase in jet fuel consumption and its associated emissions across the world have led to the need for alternative technologies to produce sustainable aviation fuels (SAF). One option to produce SAFs is to utilize waste or biomass-based feedstocks that has the potential to reduce greenhouse gas emissions by 50% or more compared to conventional jet fuel. However, there is a lack of understanding of how the synergistic effects of key performance variables could hinder or help the deployment of aviation fuels on a regional scale. Here, we assess the implications of key variables-including type and quantity of waste/biomass feedstock availability near the airport, cost of SAF production, life cycle greenhouse gas (GHG) emissions, policies, and fuel/infrastructure logistics-on the deployment of SAF at Chicago's O'Hare International Airport. We consider three ASTM International-approved SAF technologies (Hydroprocessed Esters and Fatty Acids, Fischer-Tropsch, and Alcohol to Jet) that can be blended up to 50% with petroleum-based jet fuel. Results from our analysis show that woody biomass-based Fischer-Tropsch technology has the lowest fuel production costs ($2.31-$2.81/gallon gasoline equivalent) of all pathways, and it reduces life cycle GHG emissions by 86% compared to conventional jet fuel despite the higher availability of crop residues compared to either woody biomass or fats, oils, and greases. Also, infrastructure is available at O'Hare International Airport to blend SAF with Jet A fuel through three terminals directly connected to the airport via pipelines. Our sensitivity analysis shows renewable fuel incentives and feedstock price to be key performance variables affecting the production cost and deployment of SAF.

alcohol-to-jet↗
DOE OSTI2024

Heterogeneous oxidation of hydrogen-natural gas blends in a safe, clean, and efficient burner design

The growth of hydrogen as an alternative clean fuel for fulfilling thermal energy needs of multiple economic sectors globally requires access to reliable, safe, energy efficient, emission free combustion technology. The work described in this short communication shows the applicability of a novel heterogeneous combustion design in utilizing a wide range of hydrogen blended methane concentrations to cleanly and safely generate thermal energy. The utilization of a simple first principles design approach along with engineered materials yielded a fuel-flexible hybrid infrared-convection burner design capable of lowering NOx emissions by more than 95% while simultaneously improving the heat transfer efficiency by 15% with a wide range of hydrogen concentrations. Here, the safety and performance of the combustion design was demonstrated in an burner at capacities of up to 12,000 Btu/h in producing temperatures of 900 °C. The atmospheric burner concept was integrated in a cooktop configuration with combined thermal power rating of 30,000 Btu/h and operated with hydrogen blended natural gas.

08 HYDROGEN↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗
DOE OSTI2025

A Systems Framework to Enhance the Potential of Camelina as Oilseed Crop (Final Report)

To alleviate the dependency of the United States on fossil fuels, particularly from foreign sources, the transition to biofuel crops has long been proposed as a crucial part of the long-term solution. Camelina sativa has emerged as one of the most promising oilseed crops for domestic biofuel and bioproduct production due to its low agronomic input requirements, natural resilience to a wide range of biotic and abiotic stresses, and the successful testing and approval of its oil-based blends for use in liquid transportation fuels.

09 BIOMASS FUELS↗
DOE OSTI2021

Parametric Study of Used Nuclear Oxide Fuel Constituent Dissolution in Molten LiCl-KCl-UCl 3

Prior work identified dissolution of used nuclear oxide fuel constituents from a uranium oxide matrix into molten LiCl-KCl-UCl 3 at 500°C, prompting a subsequent series of three progressive studies (including an initial scoping study, an electrolytic dissolution study, and a chemical-seeded dissolution study) to further investigate associated parameters and mechanisms. Thermodynamic calculations were performed to identify possible reaction mechanisms and their propensities in used oxide fuel constituent dissolution. Used nuclear oxide fuels with varying preconditions from fast and thermal test reactors were separately immersed in the subject salt system to assess fuel constituent migration from the bulk fuel matrix to the salt phase in an initial scoping study. Dissolution of expected fuel constituents, including alkali, alkaline earth, lanthanide, and transuranium oxides, into the chloride salt phase varied widely, ranging from 12% to 99% in the initial study. Uranium isotope blending between the salt phase and bulk fuel matrix was also observed, which was attributed to reducing conditions in the fuel matrix. Electrolytic and chemical-seeded dissolution studies were subsequently performed to effect reducing conditions in the fuel. Other parameters, including temperature (at 500°C, 650°C, 725°C, and 800°C) and uranium trichloride concentrations (at 6, 9, and 19 wt% uranium), were investigated in the latter two studies, resulting in fuel constituent dissolution above 90%. Extents of dissolution were based on initial and final fuel constituent concentrations in the oxide fuels following operations in the salt and subsequent removal of the salt via distillation. Finally, in this series of progressive studies, oxide fuel preconditioning and in situ reducing conditions, along with elevated temperature and uranium trichloride concentrations, were the primary parameters promoting used nuclear oxide fuel constituent dissolution in accordance with identified reaction mechanisms.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Ignition Delay Test with Spray & Combustion Vessel

Ignition delay test results of different fuels (RON60, RON70, RON80, RON90, and biofuel blends) under different engine operating conditions with a multi-hole injector. These results were used to better understand the spray and combustion characteristics and validate the CFD real fuel model (https://doi.org/10.5281/zenodo.8432075). This work was part of the DOE funded project (DE-EE0008478; Co-optimized Mixed-Mode Engine and Fuel Demonstrator for Improved Fuel Economy while Meeting Emissions Requirements; https://doi.org/10.2172/1887341).

02 PETROLEUM↗
DOE OSTI2023

Soot Formation and Ignition Characteristics of Ethanol/Gasoline Blends in a Rapid Compression Machine

With the ever-increasing demand for sustainable energy, alcohol fuels have garnered interest for use in heavy duty engines. The significant infrastructure for ethanol production and blending of ethanol with gasoline make these fuels/fuel blends desirable candidates. However, development of heavy duty engine technology that is capable of burning alcohol fuels while retaining the advantages of traditional diesel combustion requires an improved understanding of the soot formation for these fuels under conditions relevant to mixing-controlled combustion. This work uses an extinction diagnostic to study the sooting tendency of ethanol and gasoline/ethanol blends ranging from E10 to E98 during ignition in a homogeneous environment. Experiments were conducted in a rapid compression machine (RCM) for compressed conditions of 20 ± 1 bar and an approximately constant temperature (± 10K) which was unique for each fuel. For a given soot volume fraction, a linear relationship was observed between ethanol content and the equivalence ratio in which that soot volume fraction was formed. Accounting for the oxygenated nature of ethanol, E85 and E98 fuels produced similar amounts of soot at a given Φ ox, , suggesting other factors outside of fuel oxygen content, such as fuel morphology, impact soot formation. Ignition delay data is reported for compressed pressures of 20 ± 1 bar and compressed temperatures ranging from 633 – 670 K for E10 and 771 – 789 K for E98. Varying pressures for E10 and E98 at conditions producing similar soot volume fractions demonstrated a linear dependence of soot formation on pressure, regardless of if the pressure considered was at top dead center or peak combustion pressure. Furthermore, the data gleaned from this work will be used to select soot models and chemical kinetic mechanisms for RCM simulations to ultimately model heavy duty engine technology with the studied fuels.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Understanding Biomass and Polymer Feedstock Variability Through Analytical Pyrolysis and Two Dimensional Gas Chromatography and Mass Spectrometry

Moving toward a circular carbon economy requires enabling reuse of carbon-based macromolecules like those in biomass and polymers. Meeting this goal requires increased upcycling of waste products into higher value products. For biomass waste such as corn stover, pine needles, or bark, one approach is using pyrolysis to convert these feedstocks into bio-oil that can be used for liquid fuel or transformed into other hydrocarbon based products, like bio-polymers. Waste plastics can be upcycled or recycled into new products, or alternatively converted into bio-oil by pyrolysis. Macromolecules from biomass and polymers are challenging to convert into liquid fuel or chemical feedstocks, due to large and sometimes heterogeneous networks of polymeric bonds. We work with the Idaho National Laboratory’s Biomass Feedstock National User Facility and Department of Energy’s Feedstock Conversion Interface Consortium to develop a molecular understanding of biomass variability that occurs naturally and as a result of storage or preprocessing techniques applied to feedstocks, to understand chemical reactions occurring during pyrolysis and other biomass or polymer conversion techniques. Using two dimensional gas chromatography mass spectrometry coupled to analytical pyrolysis provides insight into the molecular changes that occur during the pyrolysis event, and these insights can extend to bench or pilot scale pyrolysis conversions. Understanding pyrolysis of biomass and polymers at a molecular level contributes to development of new tools to predict and manipulate the optimum conditions and identify the best storage, preprocessing, and conversion techniques to maximize output of specific high-value chemical species in the conversion to fuels, or to characterize feedstocks for blending before pyrolysis. Identification and understanding of the molecular level changes resulting from novel preprocessing techniques that can be used to control and manipulate the chemical output of bench or pilot scale pyrolysis is another focus of investigation, including the use of gamma irradiation, acid, or enzyme pre-treatments. We also focus on the impacts of storage conditions and techniques, which can affect moisture levels, degradation, and impacts from naturally occurring microbes in the environment.

09 BIOMASS FUELS↗
DOE OSTI2020

Impact of Biofuel Blends on Black Carbon Emissions from a Gas Turbine Engine

With a view towards renewable feedstock while decreasing the CO2 footprint associated with jet travel, biofuels are receiving increasing interest. Presented here is an overview of non-volatile particulate matter (nvPM) emissions, i.e. “soot” as gauged by varied TEM analyses for a J-85 turbojet fueled with Jet-A as well as with blends of Jet-A using Camelina biofuel. A unifying explanation is provided encompassing fuels and spanning length scales across three orders of magnitude. The variation of primary particle size, aggregate size and nanostructure are analyzed as a function of biofuel blend across range of engine thrust levels. The postulate is based on where fuels start along the soot formation pathway. Increasing biofuel content lowers aromatic concentration while placing increasing dependence upon fuel pyrolysis reactions to form the requisite concentration of aromatics for particle inception and growth. The required “kinetic” time for pyrolysis reactions to produce benzene and multi-ring PAHs allows increased fuel-air mixing by turbulence, diluting the fuel-rich soot-forming regions, effectively lowering their equivalence ratio. With a lower precursor concentration, particle inception is slowed, the resulting concentration of primary particles is lowered and smaller aggregates. The lower equivalence ratio also results in smaller primary particles given the lower concentration of growth species.

Kumal, Raju R.↗
NASA NTRS1982

Catalytic combustion with steam injection

The effects of steam injection on (1) catalytic combustion performance, and (2) the tendency of residual fuel to burn in the premixing duct upstream of the catalytic reactor were determined. A petroleum residual, no. 2 diesel, and a blend of middle and heavy distillate coal derived fuels were tested. Fuel and steam were injected together into the preheated airflow entering a 12 cm diameter catalytic combustion test section. The inlet air velocity and pressure were constant at 10 m/s and 600 kPa, respectively. Steam flow rates were varied from 24 percent to 52 percent of the air flow rate. The resulting steam air mixture temperatures varied from 630 to 740 K. Combustion temperatures were in the range of 1200 to 1400 K. The steam had little effect on combustion efficiency or emissions. It was concluded that the steam acts as a diluent which has no adverse effect on catalytic combustion performance for no. 2 diesel and coal derived liquid fuels. Tests with the residual fuel showed that upstream burning could be eliminated with steam injection rates greater than 30 percent of the air flow rate, but inlet mixture temperatures were too low to permit stable catalytic combustion of this fuel.

Anderson, D. N.↗
DOE OSTI2025

Using Separation-Enhanced Isotope Ratio Mass Spectrometry to Enable Increased Renewable Carbon Content in Transportation Fuels (CRADA 525)

Stable isotope ratio measurements of carbon atoms using isotope ratio mass spectrometry (IRMS) can be an effective tool for quantifying biogenic carbon in co-processed fuels, with results approaching the precision and accuracy of accelerator mass spectrometry (AMS). The lower cost of an IRMS may enable deployment to refineries, improving access and analysis turnaround times (≤2 hours), and, by extension, provide data that can allow process optimization to maximize renewable carbon in desired refinery products. This project explored the integration of chemical separation with IRMS analyses to enable highly detailed tracking of biogenic carbon into fuel product streams separated by boiling point range, chemical class, or specific compound. Forty-nine fuels and fuel components of fossil and biogenic origin, spanning gasoline and diesel boiling point ranges, were received from three refiners and were analyzed for their δ 13 C values via IRMS. Results spanned a 13 C range from ca. 10‰ to 44‰ and reflect materials derived from sustainable sources (e.g., C4 or C3 plants, animal-based pathways, syngas) or from fossil-derived fuels. Common ranges are approximately 18‰ to 9‰ and approximately 30‰ to 20‰ for C4 and C3 plants, respectively, and approximately 34‰ to 24‰ and approximately 70‰ to 33‰ for petroleum-derived fuels and methane, respectively. Fuel-like standards were developed and tested using direct-injection elemental analyzer (EA) IRMS for liquid fuels. This method was compared with the published methods, yielding statistically similar results. Four blend curve sets were produced ranging from 0% to 100% of a fuel containing biogenic carbon, focusing on 0% to 10% biogenic carbon. Linear fits were the most applicable for two of the four blend curve sets; however, two sets were found to exhibit slightly quadratic behavior, which was more pronounced in low biogenic blend samples, necessitating second-order fits. The origin of the slight quadratic behavior remains unclear; however, the discussion points to possible interpretations. CanmetENERGY thoroughly characterized a majority of the samples using one- and two-dimensional gas chromatography (GC and GC×GC, respectively) and other analyses. Selected samples were subjected to solid phase extraction (SPE) for saturate, olefin, aromatic, and polar (SOAP) analysis, and the resulting solvent-diluted fractions containing saturates and aromatics were returned to Pacific Northwest National Laboratory (PNNL), where the solvent was removed via evaporation or physical separation using GC techniques. Characterization and separations provided an understanding of saturate and aromatic content, as well as boiling point ranges for each sample and sample fraction. Samples resulting from SPE were examined using EA-IRMS and gas chromatography combustion IRMS (GC-C-IRMS) analyses. Both approaches suggest that the range in values between end-members can be increased by selecting the paraffinic or aromatic fraction of the end-member or by selecting among individual compounds resulting from GC separation of the paraffinic fractions. Considerable work remains to put these approaches into practice and statistically validate the benefit for using a fraction or individual compound over bulk analysis of a sample. However, initial results suggest that separations provide advantages for samples having blend ratios of less than 10% biogenic blendstocks. 13 C results showed statistically similar biofuel blend results to those obtained at PNNL, although additional work is needed to obtain better reproducibility. Select samples were sent to Los Alamos National Laboratory (LANL) for IRMS measurements and Beta Analytics for AMS measurements. This work suggests that IRMS and AMS yield closely comparable results and in some circumstances, IRMS could serve as a surrogate for AMS. While additional work is needed to better resolve statistical advantages for separations and better show the comparable nature of IRMS and AMS in both the biogenic carbon analysis of bulk chemical classes, initial results from this study suggest that these should be pursued in order to proliferate this approach for quantifying biogenic carbon in transportation fuels to the refinery level, thereby potentially enabling process optimization in co-processing scenarios.

09 BIOMASS FUELS↗
DOE OSTI2021

Oxidation of an iso-paraffinic alcohol-to-jet fuel and n-heptane mixture: an experimental and modelling study

Oxidation of ATJ/n-heptane blends was studied over a wide range of test conditions, using single pulse shock tubes. Test conditions were designed to study the effect of pressure (4 and 50 bar), and fuel loading (~100-1400 ppm) on the oxidation of the blends across a wide range of temperatures (800-1300 K). These effects were observed by measuring concentrations of intermediate species formed using in-line Gas Chromatography (GC) and GCxGC TOF-MS. Results showed that increasing the initial fuel load does not have a significant impact on the results. However, increasing the pressure shifts the mixture reactivity to a lower temperature by about 150 K and causes the fuel to be oxidized instead of decomposing pyrolytically as at lower pressures. Additional experiments for pure ATJ and pure n-heptane were performed at conditions matching the ATJ/n-heptane 50 bar experiments to analyze the differences between the pure and mixed fuels. Speciation measurements were compared against predictions from a detailed kinetic model. The ability of the kinetic model to capture the effects of varying experimental test conditions on the evolution of intermediate species is discussed and kinetic analyses have been conducted to identify the important reaction pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ignition delay time and speciation of dibutyl ether at high pressures

Dibutyl ether (DBE) is a promising biofuel due to its high cetane number (~ 100) and high volumetric energy density (31.6 MJ/L). It could either be used directly in compression ignition engines or blended with other conventional or renewable fuels. Oxidation and pyrolysis kinetics of DBE are not well known, particularly at high pressures. In this work, we have experimentally investigated the chemical kinetics of DBE in three domains: (a) ignition delay time measurements in a rapid compression machine over T = 550–650 K, P = 10, 20, 40 bar, φ = 0.5, 1; (b) ignition delay time measurements in a shock tube over T = 900–1300 K, P = 20, 40 bar, φ = 0.5, 1; (c) laser-based carbon monoxide speciation measurements in a shock tube during DBE pyrolysis and oxidation over T = 1100–1400 K, P = 20 bar. Pressure time-histories measured in RCM experiments exhibited unique 3-stage and 4-stage ignition behavior predominantly at fuel-lean conditions. Experimental data were compared with the predictions of two recent chemical kinetic models of DBE. Sensitivity analyses were carried out to identify key reactions which may have caused the discrepancy between experiments and simulations. We found that the rate of decomposition of DBE may need to be revisited to improve the oxidative and pyrolytic predictions of DBE kinetic model.

09 BIOMASS FUELS↗