Search NASA⌕ Search

SEARCH · Search NASA

Results for “interrupt”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Metal fluxes at the sediment–water interface in a free water surface constructed wetland

Metal biogeochemistry in the sediment, water, and the sediment–water interface (SWI) was studied in a free water surface constructed wetland. Concentrations of labile copper (Cu), zinc (Zn), sulfate, chloride, and dissolved organic carbon (DOC) were measured with the diffusive gradients in thin film (DGT) and peeper. A good agreement between peeper- and DGT-measured metals was observed for Cu (regression r 2 = 0.3, 95% CI of the slopes > 0), but not for Zn (95% CI of the slopes overlapped with 0), which was attributed to the different complexed compounds between Cu and Zn in porewater. The depth profile of labile metals in sediment porewater varied with time and was consistent with the solid-phase metal deposition, showing higher concentrations in the surface layer (3 to –3 cm) than in the bottom layer (–4 to –13 cm). The depth-averaged labile Cu and Zn concentrations measured by DGT were 1.0 and 3.1 µg/L, and labile sulfate, chloride, and DOC concentrations measured by peeper were 1.8, 3.6, and 2.1 mg/L, respectively. A sharp decrease in sulfate occurred in September when sulfate concentrations became the lowest among sampling months. This was caused by the seasonal sulfur cycles in the wetland, where the dominant sulfur reaction is sulfate reduction in warm seasons and sulfide oxidation in cold seasons. Different metal-removal mechanisms were observed in the two wetland cells; sulfur dynamics controlled the removal processes in the cell without frequent disturbance but failed to influence metal removal in the cell with frequent disturbance due to the interruption of anoxic layers. The flux ratios that compare labile element concentrations between the water column and the SWI (R-Cu, R-Zn, R-DOC, R-sulfate, and R-chloride) were generated to determine metal diffusive fluxes at the interface. Labile Zn was mostly transported from the water to the SWI during all seasons (R-Zn < 1 for all months except January). Labile Cu moved from the SWI to the water during the warm months (R-Cu < 1), which was explained by the bioturbation-induced transport of organic matter based on the positive correlations between R-Cu and R-DOC. In general, sediment can serve either as a sink or a source depending on the environmental conditions, metal speciation, and presence of living organisms. Here, metal flux at the SWI is a key component in the biogeochemical cycling of a constructed wetland.

54 ENVIRONMENTAL SCIENCES↗

Evolution of damage and failure in an additively manufactured 316L SS structure: experimental reinvestigation of the third Sandia fracture challenge

The third Sandia Fracture Challenge (SFC3) was a benchmark problem for comparing experimental and simulated ductile deformation and failure in an additively manufactured (AM) 316L stainless steel structure. One surprising observation from the SFC3 was the Challenge-geometry specimens had low variability in global load versus displacement behavior, attributed to the large stress-concentrating geometric features dominating the global behavior, rather than the AM voids that tend to significantly influence geometries with uniform cross-sections. This current study reinvestigates the damage and failure evolution of the Challenge-geometry specimens, utilizing interrupted tensile testing with micro-computed tomography (micro-CT) scans to monitor AM void and crack growth from a virgin state through complete failure. This study did not find a correlation between global load versus displacement behavior and AM void attributes, such as void volume, location, quantity, and relative size, which incidentally corroborates the observation from the SFC3. However, this study does show that the voids affect the local behavior of damage and failure. Surface defects (i.e. large voids located on the surface, far exceeding the nominal surface roughness) that were near the primary stress concentration affected the location of crack initiation in some cases, but they did not noticeably affect the global response. The fracture surfaces were a combination of classic ductile dimples and crack deviation from a more direct path favoring intersection with AM voids. Even though the AM voids promoted crack deviation, pre-test micro-CT scan statistics of the voids did not allow for conclusive predictions of preferred crack paths. This study is a first step towards investigating the importance of voids on the ductile failure of AM structures with stress concentrations.

36 MATERIALS SCIENCE↗

Analysis of Transient Recovery Voltage at the Terminals of Breakers Using Current-Limiting Reactors

Current-limiting reactors (CLR) are known to have a significant effect on transition processes during short circuits (SC) leading to excesses beyond the permissible values of the transient recovery voltage (TRV) at the terminals of breakers for short-circuit currents, which in turn can lead to failure of the breakers. It is shown that the traditional (generally accepted) method for calculating transient recovery voltages based on using a circuit with the reactor replaced by lumped parameters is not suitable for magnetized CLR, and in the case of uncontrolled CLR can yield erroneous results. It is argued that there is a need to account for the distribution of the winding parameters of current-limiting reactors in calculations of the TRV at the contacts of breakers as they interrupt short circuits and relevant analytic expressions are derived.

42 ENGINEERING↗

An efficient hybrid visible light communication/radio frequency system for vehicular applications

This paper focuses on improving the traffic system for Intelligent Transportation System (ITS) by using an imaging receiver instead of photodiode as a single receiver. Here, two simple traffic models have been proposed and analyzed in order to optimize the design characteristics such as signal to noise ratio, required power, received information, bit error rate, and modulation technique. First, a standalone visible light communication (VLC) with different modulation techniques is considered. The On–OFF Keying, L-Pulse Position Modulation (L-PPM), and Inverse L-Pulse Position Modulation (I-L-PPM) are investigated. Then, a hybrid communication system utilizing VLC and radio frequency (RF) is proposed for position-based services. The VLC/RF system combines the benefits of both systems and offers long distance transmission which is an important concern in ITS and in order to improve the link reliability in infrastructure to vehicle communications. This means that the probability of having a communication link between the transmitter and receiver is maintained without interruption. Then, the performance is finally evaluated. The obtained simulation results show a considerable increase in the received information using the proposed hybrid VLC/RF system compared to a VLC system.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The environmental impact of hydropower: a systematic review of the ecological effects of sub-daily flow variability on riverine fish

Hydropower can help facilitate power grid decarbonization because it can respond to short-term changes in power demand and is comparatively more reliable than intermittent wind and solar. However, flexible hydropower operations can create rapid and abnormal fluctuations in downstream flow conditions, which can negatively impact aquatic ecosystems. Accordingly, we conducted a systematic review on the ecological effects of hydropower-driven sub-daily flow variability (SDFV) on riverine fishes. We reviewed and synthesized 109 articles relevant to fish-SDFV relationships from seven sources, most of which focused on Salmonids in North America and northern and western Europe and were published in the last 15 years. We found strong agreement in the literature that SDFV increases fish stranding risk, destabilizes habitat, and decreases production and diversity. We found moderate agreement that SDFV interrupts fish reproduction, increases or has no impact on condition, and prompts or discourages movement depending on local channel conditions. We found little to no agreement for relationships between SDFV and mortality, physiology, and behavior. The effects of SDFV on riverine fish ecology are intertwined in the complex suite of biotic and abiotic characteristics that structure aquatic ecosystems and are highly site-, species-, and life stage-specific. Assessments of the impact of SDFV on fish ecology should first characterize local habitat and channel quality and fish community composition to identify specific, measurable ecological outcomes to sustain or enhance, and then design mitigation strategies tailored to those ecological objectives.

13 HYDRO ENERGY↗

Designing Energy Efficient Communication Runtime Systems: A View from PGAS Models

As the march to the Exascale computing gains momentum, energy consumption of supercomputers has emerged to be the critical roadblock. While architectural innovations are imperative in achieving computing of this scale, it is largely dependent on the systems software to leverage the architectural innovations. Parallel applications in many computationally intensive domains have been designed to leverage these supercomputers, with legacy two-sided communication semantics using Message Passing Interface. At the same time, Partitioned Global Address Space Models are being designed which provide global address space abstractions and one-sided communication for exploiting data locality and communication optimizations. PGAS models rely on one-sided communication runtime systems for leveraging high-speed networks to achieve best possible performance. In this paper, we present a design for Power Aware One-Sided Communication Library - PASCoL. The proposed design detects communication slack, leverages Dynamic Voltage and Frequency Scaling (DVFS) and Interrupt driven execution to exploit the detected slack for energy efficiency. We implement our design and evaluate it using synthetic benchmarks for one-sided communication primitives, Put, Get and Accumulate and uniformly non-contiguous data transfers. Our performance evaluation indicates that we can achieve significant reduction in energy consumption without performance loss on multiple one-sided communication primitives. The achieved results are close to the theoretical peak available with the experimental test bed.

Vishnu, Abhinav↗

Characterization of X80 and X100 Microalloyed Pipeline Steel Using Quantitative X-ray Diffraction

Quantitative X-ray diffraction characterization of four (4) X80 and three (3) X100 microalloyed steels was undertaken. The effect of through-thickness position, processing parameters, and composition on the measured crystallite size, microstrain, and J index (relative magnitude of crystallographic texture) was determined. Microstructure analysis using optical microscopy, scanning electron microscopy, transmission electron microscopy, and electron-backscattered diffraction was also undertaken. The measured value of microstrain increased with increasing alloy content and decreasing cooling interrupt temperature. Microstructural features corresponding to crystallite size in the X80 steels were both above and below the detection limit for quantitative X-ray diffraction. The X100 steels consistently exhibited microstructure features below the crystallite size detection limit. The yield stress of each steel increased with increasing microstrain. The increase in microstrain from X80 to X100 is also associated with a change in microstructure from predominantly polygonal ferrite to bainitic ferrite.

36 MATERIALS SCIENCE↗

Controlled Growth of Ordered III-Nitride Core-Shell Nanostructure Arrays for Visible Optoelectronic Devices

In our paper, we demonstrate the growth of ordered arrays of nonpolar {101 ¯ 0} core–shell nanowalls and semipolar {101 ¯ 1} core–shell pyramidal nanostripes on c-plane (0001) sapphire substrates using selective-area epitaxy and metal organic chemical vapor deposition. The nanostructure arrays are controllably patterned into LED mesa regions, demonstrating a technique to impart secondary lithography features into the arrays. Moreover, we study the dependence of the nanostructure cores on the epitaxial growth conditions and show that the geometry and morphology are strongly influenced by growth temperature, V/III ratio, and pulse interruption time. We also demonstrate the growth of InGaN quantum well shells on the nanostructures and characterize the structures by using micro-photoluminescence and cross-section scanning tunneling electron microscopy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of TiO{sub 2} Addition on Grain Growth, Anodic Bubble Evolution and Anodic Overvoltage of NiFe{sub 2}O{sub 4}-Based Composite Inert Anodes

A two-step powder compaction and sintering process was employed to fabricate TiO{sub 2}-doped NiFe{sub 2}O{sub 4} ceramic-based inert anodes. Grain growth during isothermal sintering was analyzed using Brook grain growth model. The bubble behavior of NiFe{sub 2}O{sub 4} ceramic-based inert anodes was investigated in a two-compartment see-through quartz cell for aluminum electrolysis process. Anodic overvoltage and potential decay curves of the inert anodes were measured by using the steady state and current interruption technique. The results showed that the kinetic index of grain growth decreased with an increase in temperature. The average activation energy of grain growth for 1.0 wt.% TiO{sub 2}-doped NiFe{sub 2}O{sub 4} ceramic samples with a sintering temperature range from 1373 to 1673 K dropped from 675.30 to 183.47 kJ/mol. The diameter size of bubbles before releasing from the bottom surface of the anodes was reduced with increasing the current density, and the larger average releasing bubble size for carbon anode at the same current density could be obtained, which was compared to the NiFe{sub 2}O{sub 4} inert anodes. Besides, the cell voltage of carbon anodes fluctuated much more violently under the same experimental conditions. After adding small amount of TiO{sub 2}, a minor reduction in anodic overvoltage of NiFe{sub 2}O{sub 4}-based anodes can be observed.

36 MATERIALS SCIENCE↗

Experimental Investigation of the System Nonmetallic Inclusion-Molten Steel-Refractory System at High Temperatures

In continuous casting, the buildup of particles in the flow control system is called clogging. Clogging may be caused by preexisting nonmetallic inclusions attached to the refractory wall, interrupting or disturbing the fluid flow conditions. The interfacial properties of the nonmetallic inclusion-molten steel-refractory system are believed to play a key role in the clogging tendency of selected steel grades in contact with ceramics. The combination of a high-temperature laser scanning confocal microscope (HT-LSCM), which is employed for in situ observation of inclusions’ behavior in the liquid steel or at the steel/ceramic interface, and a high-temperature drop shape analyzer (HT-DSA), which is utilized for contact angle measurements, enabled the investigation of reactions and interactions in the described system at experimental temperatures of approximately 1600 °C. The objective of this study was to develop a method to obtain qualitative information on the deposition of nonmetallic inclusions (NMIs) in the submerged entry nozzle (SEN) during casting. The behavior of solid NMIs from a calcium-treated steel at the interface between liquid steel and Al{sub 2}O{sub 3} or MgO was investigated by means of HT-LSCM. During the test evaluation, inclusions were found to separate at the steel/ceramic interface due to an attractive force. This force increased with the NMIs’ size as well as with the ceramic particle change. The HT-DSA provided contact angle data between molten steel and the ceramic used for implementation into the theoretical capillary force model. A clear correspondence between the estimated and calculated capillary forces was observed. The change in the wettability of the system, as induced by the change in the ceramic from MgO to Al{sub 2}O{sub 3}, showed a reduction of the attractive forces, indicating a weaker separation toward the SEN for the same inclusion type. This study confirmed the strong potential of wettability investigations to predict the clogging tendency of certain steel grades.

36 MATERIALS SCIENCE↗

Finite Element Simulation and Optimization of Gas-Quenching Process for Tool Steels

Various gas-quenching processes, including marquenching, were investigated to optimize gas-quenching processes in terms of distortion and hardness by means of numerical and experimental analyses. The temperature, microstructure, hardness, and distortion during the various gas-quenching processes of a tool steel block were simulated using a finite element method based on a coupled thermo-metallurgical–mechanical model. The predicted temperature, hardness, and distortion agreed well with the experimental data. The tool steel block (200 × 150 × 70 mm{sup 3}) quenched under 10 bar pressure of nitrogen gas (Case 2) had higher hardness due to the higher martensite fraction and larger distortion owing to the higher thermal stress induced by faster cooling, compared to the block quenched under 2 bar pressure of nitrogen gas (Case 1). The tool steel block marquenched under 10 bar pressure of nitrogen gas interrupted by isothermal holding at 500 °C (Case 3) had 30% smaller distortion with a negligible loss of hardness compared to Case 2. Furthermore, the simulation results could provide an optimized process condition to minimize distortion of the gas-quenched tool steel block while satisfying the hardness requirement.

36 MATERIALS SCIENCE↗

A Study of Microstructure Evolution During Creep of 9Cr-1Mo Steel Using Ultrasonic and Hardness Measurements

In this work, microstructural changes during creep of 9Cr-1Mo steel were characterized using ultrasonic and hardness measurements. The creep testing of this steel was firstly performed at 873 K under the initial stresses of 160 and 175 MPa, respectively. Then, eight specimens under each stress level were prepared by the interrupted tests to simulate various creep states. Subsequently, two parameters of ultrasonic attenuation and velocity were introduced by the ultrasonic testing. Experiment results showed that regardless of the stresses, the ultrasonic attenuation experiences a peak at about 20% of the creep rupture time and a minimum value at about 50%, showing a strong correlation between ultrasonic attenuation and the creep life fraction. In addition to a slight increase during the primary creep, the ultrasonic velocity exhibits a significant change during the tertiary creep. Based on the analysis of microstructure changes, it indicated that the ultrasonic attenuation is significantly sensitive to the dynamic changes of the dislocation. In contrast, the velocity is mainly related to the evolution of precipitates. The Vickers hardness decreases monotonously during the creep process and presents a linear relation with the inverse of average diameter of M{sub 23}C{sub 6} carbides during the secondary and tertiary creep. Accordingly, it suggested that the present ultrasonic and hardness measurements provided a convenient tool to evaluate the microstructure evolution during creep degradation of heat-resistant steels.

36 MATERIALS SCIENCE↗

Interaction of Strain Refined Precipitates and Recrystallized Grains in Nb-Ti Microalloyed Steel during Continuous Casting, Hot-Core Heavy Reduction Rolling, and Reheating Process

Hot-core heavy reduction rolling (HHR{sup 2}) is an energy-saving process that directly rolls continuously cast slabs at the end of solidification that have a large temperature gradient. Here, we elucidated the interaction of strain refined precipitates and recrystallized grains in Nb-Ti microalloyed steel during continuous casting, hot-core heavy reduction rolling, and reheating process. Furthermore, theoretical models were established to calculate recrystallization driving force and pinning force at temperatures in the range of 850-1300 °C by a two-stage interrupted compression test using a Gleeble-3800 thermomechanical simulator. The study indicated that a random dispersion of strain refined precipitates with a size range of ~ 6-10 nm was obtained in the hot-core heavy reduction rolled slab, which was different from the coarse and uneven distribution of precipitates in a conventional slab. Upon reheating, the austenite grains in the hot-core heavy reduction rolled slab were significantly refined and evenly distributed along the thickness direction. This is attributed to the random dispersion of strain refined precipitates formed in the HHR{sup 2} process.

36 MATERIALS SCIENCE↗

The Evolution of Deformation-Induced Carbides during Divorced Eutectoid Transformation in GCr15 Steels

A series of rolling experiments were carried out using GCr15 steel to investigate the effect of initial microstructure on the spheroidizing process, and especially the effect of deformation-induced carbides (DIC) on the divorced eutectoid transformation (DET). The results indicated that the existence of DIC was beneficial to the spheroidizing process, the optimal initial microstructure for DET was lamellar pearlite, and DIC precipitated at grain boundaries. The average thickness of the cementite lamella and the size of DIC decreased with a decrease in rolling temperature in the critical temperature region. When the specimen was rolled at 1053 K, a small amount of DIC of size ~ 1 μm precipitated at grain boundaries. In contrast, the amount of DIC was increased when the rolling temperature was decreased to 1023 K, whereas the size of DIC was reduced to ~ 0.5 μm. Interrupted quenching experiments indicated that DIC (M{sub 7}C{sub 3}) were transformed to M{sub 3}C during the process of partial austenitization, and the evolution of spheroidization was influenced by the variation in the initial microstructure. For the specimens rolled at 1023 K, only ~ 60 min was needed to achieve the dissolution of DIC, which was the minimum, and the total time needed to achieve spheroidization was reduced to ~ 90 min.

36 MATERIALS SCIENCE↗

Magnetron-Sputtered Ni-Cr and Ti-Si Layers to Protect Ti-46Al-8Nb (at.%) Substrates Against Gas Absorption

Ni-Cr and Ti-Si layers were deposited by magnetron sputtering on Ti-46Al-8Nb (at.%) substrates to suppress penetration of gases, which brings about undesirable changes in mechanical properties. Alloy samples with and without surface protection were subjected to interrupted oxidation at elevated temperature (700 and 800 °C) for up to 300 h. Selected mechanical properties as well as adhesion of surface layers were examined in the as-received and oxidized state. Analytical techniques used to characterize surfaces and cross sections of the samples included scanning electron microscopy and light microscopy, energy-dispersive x-ray spectroscopy, x-ray photoelectron spectroscopy and x-ray diffraction. Both investigated layers were sufficiently adherent and effective in hindering gas absorption at 700 °C; however, only Ni-Cr showed promising properties for higher-temperature applications.

36 MATERIALS SCIENCE↗

Microstructure and Three-Point Bending Fatigue Behavior of Al-Cu-Mg-Ag Alloys with Various Mg Contents

This paper presents an investigation on the influence of Mg content on the microstructures, tensile properties and three-point bending fatigue behavior of Al-Cu-Mg-Ag alloys. The results indicate that the alloy containing 0.70 wt.% Mg possesses lower tensile properties and higher fatigue performance compared to the one with 1.15 wt.% Mg. Increasing Mg content in Al-Cu-Mg-Ag alloys can enhance the nucleation and precipitation of Ω phase, as well as increase the volume fraction and number density of constituent particles. The investigation of the fatigue crack initiation and growth behavior of Al-Cu-Mg-Ag alloy using interrupted fatigue tests suggests that micro-cracks mainly nucleate on Al{sub 2}Cu constituent particles and the fatigue life is mainly associated with the density of constituent particles.

36 MATERIALS SCIENCE↗

Microgrid Resilience: A Holistic and Context-Aware Resilience Metric

Microgrids present an effective solution for the coordinated deployment of various distributed energy resources and furthermore provide myriad additional benefits such as resilience, decreased carbon footprint, and reliability to energy consumers and the energy system as a whole. Boosting the resilience of distribution systems is another major benefit of microgrids. This is because they can also serve as a backup power source when the utility grid's operations are interrupted due to either high-probability low-impact events like a component failure or low-probability high-impact events - be it a natural disaster or a planned cyberattack. However, the degree to which any particular system can defend, adapt, and restore normal operation depends on various factors including the type and severity of events to which a microgrid is subjected. These factors, in turn, are dependent on the geographical location of the deployed microgrid as well as the cyber risk profile of the site where the microgrid is operating. Therefore, in this work, we attempt to capture this multi-dimensional interplay of various factors in quantifying the ability of the microgrid to be resilient in these varying aspects. This paper, thus, proposes a customized site-specific quantification of the resilience strength for the individual microgrid's capability to absorb, restore, and adapt to the changing circumstances for sustaining the critical load when a low-probability high-impact event occurs - termed as - context-aware resilience metric. We also present a case study to illustrate the key elements of our integrated analytical approach.

microgrid↗

Acquisition of Real-Time Operation Analytics for an Automated Serial Sectioning System

Mechanical serial sectioning is a highly repetitive technique employed in metallography for the rendering of 3D reconstructions of microstructure. While alternate techniques such as ultrasonic detection, micro-computed tomography, and focused ion beam milling have progressed much in recent years, few alternatives provide equivalent opportunities for comparatively high resolutions over significantly sized cross-sectional areas and volumes. To that end, the introduction of automated serial sectioning systems has greatly heightened repeatability and increased data collection rates while diminishing opportunity for mishandling and other user-introduced errors. Unfortunately, even among current, state-of-the-art automated serial sectioning systems, challenges in data collection have not been fully eradicated. Therefore, this paper highlights two specific advances to assist in this area; a non-contact laser triangulation method for assessment of material removal rates and a newly developed graphical user interface providing real-time monitoring of experimental progress. Furthermore, both are shown to be helpful in the rapid identification of anomalies and interruptions, while also providing comparable and less error-prone measures of removal rate over the course of these long-term, challenging, and innately destructive characterization experiments.

36 MATERIALS SCIENCE↗