Search NASA⌕ Search

SEARCH · Search NASA

Results for “lateral force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Lateral Stability Characteristics of a 1/8.33-Scale Powered Model of the Republic XF-12 Airplane

The XF-12 airplane is a high-performance photo-reconnaissance aircraft designed for the Army Air Forces by the Republic Aviation Corporation. An investigation of a 1/8.33 - scale powered model was made in the Langley l9-foot pressure tunnel to obtain information relative to the aerodynamic design of the airplane. The model was tested with and without the original vertical tail. and with two revised tails. For the revised tail no. 1, the span of the original vertical .tail was increased about 15 percent and the portion of the vertical tail between the stabilizer and fuselage behind the rudder hinge line was allowed to deflect simultaneously with the main rudder. Revision no. 2 incorporated the increased span, but the lower rudder was locked in the neutral position. For all the tail arrangements investigated it was indicated that the airplane will possess positive effective dihedral and will be directionally stable regardless of flap or power condition. The rudder effectiveness is greater for the revised tails than for the original tail, but this is offset by the increase in directional stability caused by the revised tail. All the rudder arrangements appear inadequate in trimming out the resultant yawing moments at zero yaw in a take - off condition with the left-hand outboard propeller windmilling and the remaining engines developing take-off power.

Pepper, Edward↗
NASA NTRS1976

Side forces on a tangent ogive forebody with a fineness ratio of 2.5 at high angles of attack and low speed

A wind tunnel study to determine the subsonic aerodynamic characteristics, at high angles of attack, of a tangent ogive forebody with a fineness ratio of 2.5, is reported. Static longitudinal and lateral-directional stability data were obtained at Reynolds numbers ranging from 0.4 x 1 million to 3.7 x 1 million (based on base diameter) at a Mach number of 0.25. Angle of attack was varied from 36 deg to 88 deg at zero sideslip. It was found that at low Reynolds numbers the forebody does not have a side force att high angles of attack; however, at Reynolds numbers above about 2 x 1 million, a side force occurs in the angle of attack range from 45 deg to 80 deg. The maximum side force is as large as the maximum normal force. The maximum normal force coefficient varies between 1.0 and 2.0 over the Reynolds number range tested and occurs at angles of attack near 65 deg.

Keener, E. R.↗
NASA NTRS1937

Full-scale Wind-tunnel and Flight Tests of a Fairchild 22 Airplane Equipped with External-airfoil Flaps

Wind-tunnel and flight tests have been made of a Fairchild 22 airplane equipped with a wing having external-airfoil flaps that also perform the function of ailerons. Lift, drag, and pitching-moment coefficients of the airplane with several flap settings, and the rolling- and yawing-moment coefficients with the flaps deflected as ailerons were measured in the full-scale tunnel with the horizontal tail surfaces and propeller removed. The effect of the flaps on the low speed and on the take-off and landing characteristics, the effectiveness of flaps when used as ailerons, and the forces required to operate them as ailerons were determined in flight. The wind-tunnel tests showed that the flaps increased the maximum lift coefficient of the airplane from 1.51 with the flap in the minimum drag position to 2.12 with the flap in the minimum drag position to 2.12 with the flap deflected 30 degrees. In the flight tests the minimum speed decreased from 46.8 miles per hour with the flaps up to 41.3 miles per hour with the flaps deflected. The required take-off run to attain a height of 50 feet was reduced from 820 to 750 feet and the landing run from a height of 50 feet was reduced from 930 to 480 feet. The flaps for this installation gave lateral control that was not entirely satisfactory. Their rolling action was good but the adverse yaw resulting from their use was greater than is considerable, and the stick forces required to operate them increased too rapidly with speed.

Reed, Warren D↗
NASA NTRS1974

Free-flight investigation of the stability and control characteristics of a STOL model with an externally blown jet flap

The stability and control characteristics of a four-engine turbofan STOL transport model having an externally blown jet flap have been investigated by means of the flying-model technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated under conditions of symmetric and asymmetric (one engine inoperative) thrust at lift coefficients up to 9.5 and 5.5, respectively. Static characteristics were studied by conventional power-on force tests over the flight-test angle-of-attack range including the stall. In addition to these tests, dynamic longitudinal and lateral stability calculations were performed for comparison with the flight-test results and for use in correlating the model results with STOL handling-qualities criteria.

Parlett, L. P.↗
NASA NTRS1980

Post-buckling behavior of a beam-column on a nonlinear elastic foundation with a gap

The structural behavior of an elastic beam-column placed with a gap between two nonlinearity elastic layers each resting on a rigid foundation was examined. The beam-column was laterally supported at both ends and subjected to a uniform transverse load and axial compression. Its slenderness was such that the axial compressive force exceeds the amount that would be necessary to buckle it as a simple supported column. The elastic layers were represented by an elastic foundation with a strongly nonlinear specific reaction taken as a rapidly increasing function of the layer compression. The analytical model developed simulated the entire pattern of the deflection and stress state including layer and end support reactions, under gradually increasing axial force.

Kuznetsov, E. N.↗
NASA NTRS1986

The equivalent angle-of-attack concept for engineering analysis

An account is given of methods for the estimation of a wing-body-tail missile configuration's aerodynamic performance by means of the 'component buildup' method, in which the overall aerodynamic loads for an airframe are built up from the assumed characteristics of isolated airframe components and then subjected to additional loads generated by component interference. Attention is given to the cases of missile airframes in steady flow at arbitrary angles of attack and bank; the unifying thread of the present treatment is slender body theory, together with its nonlinear extensions through the equivalent angle-of-attack concept. The estimation of the forces and moments acting on each of the fins is emphasized, so that control cross-coupling effects as well as longitudinal and lateral directional effects can be determined.

Hemsch, M. J.↗
NASA NTRS1990

Theoretical hypervelocity ballistic limit for single or double plates using nonlinear modal analysis

The original research on the use on nonlinear vibration technique to solve for the hypervelocity ballistic limit for double plates is examined. Such structure is commonly found in typical Space Station design where the incoming space or man-made debris would be fragmented upon hitting the outer plate (shield) and the subsequent impact on the main wall would result in a much reduced damge of the space station or spacecraft. The existing few theoretical impact equations do not agree well with each other. The existing computer code bumper used at NASA-Johnson Space Center appears to predict an unconservative ballistic limit when compared with experimental data where the velocity ranges from 3 km/s to 8 km/s. Such unconservative prediction is unacceptable from a practical safe design point of view. The bumper code is based on Wilkinson's (1968) paper and his equations have not been improved nor modified even though they are viewed with suspicion due to lack of agreement with experiments. To make matters worse, there is not another theory which is better than Wilkinson's equation and the designers are forced to use purely empirical Nysmith (1969) or semiempirical equations developed by Cour-Palais in 1969. The Cour-Palais equations were later modified empirically in 1989. The purpose of the present investigation is to examine the many assumptions of the Wilkinson equation. An attempt is made to present design charts based on the modified-Wilkinson equation so that the designer can get a feel of the ranges of the parameters which are of interest and discard a huge range of parameters, thus, significantly reducing the number of test shots required. The analysis is based on a solution of the governing nonlinear differential equations for a plate, assuming axisymmetric behavior using polar coordinates.

Hui, David↗
NASA NTRS1992

Component build-up method for engineering analysis of missiles at low-to-high angles of attack

Methods are presented for estimating the component build-up terms, with the exception of zero-lift drag, for missile airframes in steady flow and at arbitrary angles of attack and bank. The underlying and unifying bases of all these efforts are slender-body theory and its nonlinear extensions through the equivalent angle-of-attack concept. Emphasis is placed on the forces and moments which act on each of the fins, so that control cross-coupling effects as well as longitudinal and lateral-directional effects can be determined.

Hemsch, Michael J.↗
NASA NTRS1993

Head-on collision of drops: A numerical investigation

The head-on collision of equal sized drops is studied by full numerical simulations. The Navier-Stokes equations are solved for fluid motion both inside and outside the drops using a front tracking/finite difference technique. The drops are accelerated toward each other by a body force that is turned off before the drops collide. When the drops collide, the fluid between them is pushed outward leaving a thin later bounded by the drop surface. This layer gets progressively thinner as the drops continue to deform and in several of the calculations this double layer is artificially removed once it is thin enough, thus modeling rupture. If no rupture takes place, the drops always rebound, but if the film is ruptured the drops may coalesce permanently or coalesce temporarily and then split again.

Nobari, M. R.↗
NASA NTRS1995

Computational Study of Flow Establishment in Hypersonic Pulse Facilities

This paper presents a study of the temporal evolution of the combustion flowfield established by the interaction of ram-accelerator-type projectiles with an explosive gas mixture accelerated to hypersonic speeds in an expansion tube. The Navier-Stokes equations for a chemically reacting gas are solved in a fully coupled manner using an implicit, time accurate algorithm. The solution procedure is based on a spatially second order, total variation diminishing (TVD) scheme and a temporally second order, variable-step, backward differentiation formula method. The hydrogen-oxygen chemistry is modeled with a 9-species, 19-step mechanism. The accuracy of the solution method is first demonstrated by several benchmark calculations. Numerical simulations of expansion tube flowfields are then presented for two different configurations. In particular, the development of the shock-induced combustion process is followed. In one case, designed to ensure ignition only in the boundary layer, the lateral extent of the combustion front during the initial transient phase was surprisingly large. The time histories of the calculated thrust and drag forces on the ram accelerator projectile are also presented.

Yungster, S.↗
NASA NTRS1996

Aspirating Seal Development: Analytical Modeling and Seal Test Rig

This effort is to develop large diameter (22 - 36 inch) Aspirating Seals for application in aircraft engines. Stein Seal Co. will be fabricating the 36-inch seal(s) for testing. GE's task is to establish a thorough understanding of the operation of Aspirating Seals through analytical modeling and full-scale testing. The two primary objectives of this project are to develop the analytical models of the aspirating seal system, to upgrade using GE's funds, GE's 50-inch seal test rig for testing the Aspirating Seal (back-to-back with a corresponding brush seal), test the aspirating seal(s) for seal closure, tracking and maneuver transients (tilt) at operating pressures and temperatures, and validate the analytical model. The objective of the analytical model development is to evaluate the transient and steady-state dynamic performance characteristics of the seal designed by Stein. The transient dynamic model uses a multi-body system approach: the Stator, Seal face and the rotor are treated as individual bodies with relative degrees of freedom. Initially, the thirty-six springs are represented as a single one trying to keep open the aspirating face. Stops (Contact elements) are provided between the stator and the seal (to compensate the preload in the fully-open position) and between the rotor face and Seal face (to detect rub). The secondary seal is considered as part of the stator. The film's load, damping and stiffness characteristics as functions of pressure and clearance are evaluated using a separate (NASA) code GFACE. Initially, a laminar flow theory is used. Special two-dimensional interpolation routines are written to establish exact film load and damping values at each integration time step. Additionally, other user-routines are written to read-in actual pressure, rpm, stator-growth and rotor growth data and, later, to transfer these as appropriate loads/motions in the system-dynamic model. The transient dynamic model evaluates the various motions, clearances and forces as the seals are subjected to different aircraft maneuvers: Windmilling restart; start-ground idle; ground idle-takeoff; takeoff-burst chop, etc. Results of this model show that the seal closes appropriately and does not ram into the rotor for all of the conditions analyzed. The rig upgrade design for testing Aspirating Seals has been completed. Long lead-time items (forgings, etc.) have been ordered.

Bharat Bagepalli↗
NASA NTRS1996

Torsional Buckling Tests of a Simulated Solar Array

Spacecraft solar arrays are typically large structures supported by long, thin deployable booms. As such, they may be particularly susceptible to abnormal structural behavior induced by mechanical and thermal loading. One example is the Hubble Space Telescope solar arrays which consist of two split tubes fit one inside the other called BiSTEMs. The original solar arrays on the Hubble Space Telescope were found to be severely twisted following deployment and later telemetry data showed the arrays were vibrating during daylight to night and night to daylight transition. The solar array twist however can force the BiSTEM booms to change in cross-section and cause tile solar arrays to react unpredictably to future loading. The solar arrays were redesigned to correct for tile vibration, however, upon redeployment they again twisted. To assess the influence of boom cross-sectional configuration, experiments were conducted on two types of booms, (1)booms with closed cross-sections, and (2) booms with open cross-sections. Both models were subjected to compressive loading and imposed tip deflections. An existing analytical model by Chung and Thornton was used to define the individual load ranges for each model solar array configuration. The load range for the model solar array using closed cross-section booms was 0-120 Newtons and 0-160 Newtons for the model solar array using open cross-section booms. The results indicate the model solar array with closed cross-section booms buckled only in flexure. However, the results of the experiment with open cross-section booms indicate the model solar array buckled only in torsion and with imposed tip deflections the cross section can degrade by rotation of the inner relative to the outer STEM. For tile Hubble Space Telescope solar arrays the results of these experiments indicate the twisting resulted from the initial mechanical loading of the open cross-section booms.

Thornton, E. A.↗
NASA NTRS1997

Numerical Model Studies of the Martian Mesoscale Circulations

The study objectives were to evaluate by numerical modeling various possible mesoscale circulation on Mars and related atmospheric boundary layer processes. The study was in collaboration with J. Tillman of the University of Washington (who supported the study observationally). Interaction has been made with J. Prusa of Iowa State University in numerical modeling investigation of dynamical effects of topographically-influenced flow. Modeling simulations included evaluations of surface physical characteristics on: (i) the Martian atmospheric boundary layer and (ii) their impact on thermally and dynamically forced mesoscale flows. Special model evaluations were made in support of selection of the Pathfinder landing sites. J. Tillman's finding of VL-2 inter-annual temperature difference was followed by model simulations attempting to point out the forcing for this feature. Publication of the results in the reviewed literature in pending upon completion of the manuscripts in preparation as indicated later.

Segal, Moti↗
NASA NTRS1961

STOL Characteristics of a Propeller-Driven, Aspect-Ratio-10, Straight-Wing Airplane with Boundary-Layer Control Flaps, as Estimated from Large-Scale Wind-Tunnel Tests

A study is presented of the improvements in take-off and landing distances possible with a conventional propeller-driven transport-type airplane when the available lift is increased by propeller slipstream effects and by very effective trailing-edge flaps and ailerons. This study is based on wind-tunnel tests of a 45-foot span, powered model, with BLC on the trailing-edge flaps and controls. The data were applied to an assumed airplane with four propellers and a wing loading of 50 pounds per square foot. Also included is an examination of the stability and control problems that may result in the landing and take-off speed range of such a vehicle. The results indicated that the landing and take-off distances could be more than halved by the use of highly effective flaps in combination with large amounts of engine power to augment lift (STOL). At the lowest speeds considered (about 50 knots), adequate longitudinal stability was obtained but the lateral and directional stability were unsatisfactory. At these low speeds, the conventional aerodynamic control surfaces may not be able to cope with the forces and moments produced by symmetric, as well as asymmetric, engine operation. This problem was alleviated by BLC applied to the control surfaces.

Weiberg, James A↗
NASA NTRS1963

Aeroelastic Tests of an Eight Percent Scale Saturn C-1 Block II

Buffet and flutter characteristics of Saturn Apollo mission were studied using a dynamically scaled model. The model was built around a central aluminum tube for scaled stiffness distribution and strength to resist loads imposed during testing. Styrofoam sections attached to the core provided the correct external contours. Lead weights were added for correct mass distribution. An electromagnetic shaker was used to excite the model in its flexible modes of vibration during portions of the test. The model was supported on a sting, mounted by leaf springs, cables and torsion bars. The support system provided for simulating the full scale rigid body pitch frequency with minimum restraint imposed on elastic deflections. Bending moments recorded by sensors on the aluminum tube. Several modified nose configurations were tested: The basic configuration was tested with and without a flow separator disk on the escape rocket motor, tests also were made with the escape tower and rocket motor removed completely. For the final test, the Apollo capsule was replaced with a Jupiter nose cone. The test program consisted of determining model response throughout the transonic speed range at angles of attack up to 6 degrees and measuring the aerodynamic damping over the same range for the basic model and the modified configurations. Signals from the model pickup were recorded on tape for later analysis. The data obtained were used to estimate bending moments that would be produced on the full-scale vehicle by aerodynamic forces due to buffeting.

EXPERIMENTS↗
NASA NTRS1959

An Investigation of a 0.05-Scale Model of the XSM-64A Navaho Missile and Booster: Force Study at Mach Numbers from 1.77 to 3.51 - Part 1

An investigation has been conducted in the Langley Unitary Plan wind tunnel to determine the aerodynamic loads and the static longitudinal and lateral stability of a 0.05-scale model of the XSM-64A Navaho missile and booster and its various components. Tests were conducted through a Mach number range of 1.77 to 3.51 with a corresponding Reynolds number range of 2.4 x 10(exp 6) to 2.9 x 10(exp 6). Results are presented for an angle-of-attack range of -8 deg to 4 deg for the missile-booster combination and -10 deg to 10 deg for the missile-alone configuration. Tests for both configurations were conducted through an angle-of-sideslip range of -8 deg to 8 deg. Also presented are some effects on the model characteristics of the deflection of various components including canard, tip aileron, vertical stabilizer, speed brakes, and booster pitch and yaw thrust chambers. The various components on which loads were measured include the wing, tip aileron, rudder, booster, booster separating surface, booster fin, and booster yaw and pitch thrust chambers. These data are presented without analysis.

Church, James D.↗
NASA NTRS1976

The effect of lateral controls in producing motion of an airplane as computed from wind-tunnel data

An analytical study of the lateral controllability of an airplane has been made in which both the static rolling and yawing moments supplied by the controls and the reactions due to the inherent stability of the airplane have been taken into account. A hypothetical average airplane, embodying the essential characteristics of both the wind tunnel models and the full size test airplanes, was assumed for the study. Computations made of forced rolling and yawing motions of an F-22 airplane caused by a sudden deflection of the ailerons were found to agree well with actual measurements of these motions. The conditions following instantaneous full deflections of the lateral control have been studied, and some attention has been devoted to the controlling of complete turn maneuvers.

Weick, F. E.↗
NASA NTRS1975

Buoyant and capillary natural convection in infinite horizontal liquid layers heated laterally

Solutions are presented for the equations describing natural convection in a planar, horizontal layer of liquid with a constant, linear temperature gradient along the unbounded top and bottom surfaces. Both buoyancy and capillary forces are considered to drive thermal convection. The results are compared to earlier analyses for bounded liquid layers and then applied to containerless metal melts undergoing solidification in the microgravity environment of near-earth orbit.

Bourgeois, S. V.↗