SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A study using structural and stereo analysis of early and late stage geologic events within the Tellus region is performed. Evidence is presented that suggests that some tessera material may consist of layered volcanics.
Sealing interface materials and coatings are sacrificial, giving up their integrity for the benefit of the component. Seals that are compliant while still controlling leakage, dynamics, and coolant flows are sought to enhance turbomachine performance. Herein we investigate the leaf-seal configuration. While the leaf seal is classified as contacting, a ready modification using the leaf-housing arrangement in conjunction with an interface film rider (a bore seal, for example) provides for a film-riding noncontact seal. The leaf housing and leaf elements can be made from a variety of materials from plastic to ceramic. Four simplistic models are used to identify the physics essential to controlling leakage. Corroborated by CFD, these results provide design parameters for applications to within reasonable engineering certainty. Some potential improvements are proposed.
During 1976 several penetrators (full and 0.58 scale) were dropped into a test site McCook, Nebraska. The McCook site was selected because it simulated penetration into wind-deposited sediments (silts and sands) on Martian plains. The physical and chemical modifications found in the sediment after the penetrators' impact are described. Laboratory analyses have shown mineralogical and elemental changes are produced in the sediment next to the penetrator. Optical microscopy studies of material next to the skin of the penetrator revealed a layer of glassy material about 75 microns thick. Elemental analysis of a 0-1-mm layer of sediment next to the penetrator revealed increased concentrations for Cr, Fe, Ni, Mo, and reduced concentrations for Mg, Al Si, P, K, and Ca. The Cr, Fe, Ni, and Mo were in fragments abraded from the penetrator. Mineralogical changes occurring in the sediment next to the penetrator included the introduction of micron-size grains of alpha iron and several hydrated iron oxide minerals. The newly formed silicate minerals include metastable phases of silica (cristobalite, lechatelierite, and opal). The glassy material was mostly opal which formed when the host minerals (mica, calcite, and clay) decomposed. In summary, contaminants introduced by the penetrator occur up to 2 mm away from the penetrator's skin. Although volatile elements do migrate and new minerals are formed during the destruction of host minerals in the sediment, no changes were observed beyond the 2-mm distance. The analyses indicate 0.58-scale penetrators do effectively simulate full-scale testing for soil modification effects.
Graphite-copper composites are candidate materials for space based radiators. The thermal emittance of this material, however, is a factor of two lower than the desired emittance for these systems of greater than or equal to 0.85. Arc texturing was investigated as a surface modification technique for enhancing the emittance of the composite. Since the outer surface of the composite is copper, and samples of the composite could not be readily obtained for testing, copper was used for optimization testing. Samples were exposed to various frequencies and currents of arcs during texturing. Emittances near the desired goal were achieved at frequencies less than 500 Hz. Arc current did not appear to play a major role under 15 amps. Particulate carbon was observed on the surface, and was easily removed by vibration and handling. In order to determine morphology adherence, ultrasonic cleaning was used to remove the loosely adherent material. This reduced the emittance significantly. Emittance was found to increase with increasing frequency for the cleaned samples up to 500 Hz. The highest emittance achieved on these samples over the temperature range of interest was 0.5 to 0.6, which is approximately a factor of 25 increase over the untextured copper emittance.
Graphite-copper composites are candidate materials for space based radiators. The thermal emittance of this material, however, is a factor of two lower than the desired emittance for these systems of greater than or equal to 0.85. Arc texturing was investigated as a surface modification technique for enhancing the emittance of the composite. Since the outer surface of the composite is copper, and samples of the composite could not be readily obtained for testing, copper was used for optimization testing. Samples were exposed to various frequencies and currents of arcs during texturing. Emittances near the desired goal were achieved at frequencies less than 500 Hz. Arc current did not appear to play a major role under 15 amps. Particulate carbon was observed on the surface, and was easily removed by vibration and handling. In order to determine morphology adherence, ultrasonic cleaning was used to remove the loosely adherent material. This reduced the emittance significantly. Emittance was found to increase with increasing frequency for the cleaned samples up to 500 Hz. The highest emittance achieved on these samples over the temperature range of interest was 0.5 to 0.6, which is approximately a factor of 25 increase over the untextured copper emittance.
Through the Artemis program, NASA intends to develop a sustainable human foothold on the Moon, ultimately paving the way for crewed exploration of Mars. The Moon's hostile environment poses numerous obstacles, including exposure to radiation, temperature extremes, micrometeoroid threats, and particularly the persistent problem of lunar dust. Lunar dust impacts nearly every aspect of surface operations through adhesion and abrasion mechanisms, with contamination from anthropogenic activities (landing, rovers) far outweighing natural phenomena. Multiple adhesion pathways contribute to surface contamination in the lunar environment, including van der Waals forces, electrostatic forces, chemical reaction, and magnetic forces from elemental iron deposits. Sharp asperities from micrometeoroid bombardment and atmospheric absence increase interaction potential and enable mechanical interlocking. Low cohesion between dust particles exacerbates these challenges, as minimal interaction potential between dust and nearby surfaces overcomes particle cohesion, causing contamination. Lunar dust adhesion mitigation technologies can be categorized as either active, requiring external energy, or passive, relying on intrinsic material properties. Ultrasonic and electrodynamic technologies have been developed to the highest technology readiness level for active approaches. Passive strategies primarily focus on surface chemistry and topography modifications. At NASA Langley Research Center, approaches include surface migration agents to reduce surface energy, topographical modification using laser ablation patterning, and tailored surface conductivity to reduce intrinsic adhesion force. Performance has been evaluated using custom-built ultrasonic and centrifuge instruments. Plume-surface interactions from lunar landers can propel micrometer-sized particles at velocities up to 1000 m s-1.8 These particles pose risks to landers, habitats and infrastructure, leading to erosion, degradation, and reduced component lifespan. A panel recovered from Surveyor III was determined to have been severely abraded because of lunar dust displaced from the Apollo 12 lunar module that landed 160 m away. The performance of metallic surfaces has been evaluated via high velocity single particle impact using the laser-induced project impact test (LIPIT) facility at the University of Utah. Peridynamics modeling, a form of continuum mechanics that uses a nonlocal approach enabling greater simulation capabilities of crack initiation and fracture, has also been utilized to gain greater insight into material response during impact events. Lunar dust contamination challenges extend to power generation systems and moving equipment. Cables, rotation stages, and other mechanisms may experience limited range of motion and reduced lifetime due to dust infiltration. NASA Langley Research Center has evaluated traditional aerospace alloys, softgoods, wear resistant ceramics, and several polymer and polymer composite materials. Test methods have included traditional techniques like Taber abrasion testing, as well as designed test configurations developed in the DUSTE (dust, ultraviolet radiation, and space thermal environmental) chamber that reproduce mechanism functions in operational environment. Beyond laboratory experiments, several flight experiments have been conducted. Materials were exposed to the low Earth orbit environment on the Materials International Space Station Experiment (MISSE) and to the lunar surface environment through the Aegis Aerospace Regolith Adherence Characterization (RAC) payload and the Honeybee Robotics PlanetVac payload. Determining lunar dust's impact on surface exploration and habitation requires comprehensive experimental and computational capabilities combined with lessons learned from initial lunar activities. Identifying the greatest environmental challenges and developing mitigation technologies provides the clearest path toward successfully, expeditiously, and efficaciously completing NASA's mission. This presentation will discuss ongoing efforts at NASA Langley Research Center and collaborator contributions to these critical objectives.
Ionospheric modification by high power radio waves and by chemical releases are combined in a theoretical study of ionospheric focused heating. The release of materials which promote electron-ion recombination creates a hole in the bottomside ionosphere. The ionospheric hole focuses high power radio waves from a ground-based transmitter to give a 20 dB or greater enhancement in power density. The intense radio beam excites atomic oxygen by collisions with accelerated electrons. Airglow from the excited oxygen provides a visible trace of the focused beam. The large increase in the intensity of the radio beam stimulates new wave-plasma interactions. Numerical simulations show that the threshold for the two-plasmon decay instability is exceeded. The interaction of the pump electromagnetic wave with the backward plasmon produces a scattered electromagnetic wave at 3/2 the pump frequency. The scattered wave provides a unique signature of the two-plasmon decay process for ground-based detection.
A modified ultrasonic C-scan technique was implemented for improving the detection of a certain type of damage in composite specimens. The type of damage being studied is transverse (through the thickness) cracking of unidirectional off-axis graphite-epoxy specimens. These cracks are difficult to detect using standard through-transmission C-scan techniques. The modification is based on mode conversion to produce transmitted shear waves from incident longitudinal waves. While mode conversion is used extensively with isotropic materials, its use with composites is more limited. This is largely because the computation of wave propagation parameters is significantly more complicated with highly anisotropic materials than with isotropic materials. The appropriate incident angles to produce the desired mode conversion were computed based on the mechanical properties of the composite. Once the angles were computed the technique was simple to implement and resulted in marked improvement in detection of the transverse cracks being studied.
Finite element analysis of the Space Shuttle 2.5-inch frangible nut was conducted to improve understanding of the current design and proposed design changes to this explosively-actuated nut. The 2.5-inch frangible nut is used in two places to attach the aft end of the Space Shuttle Orbiter to the External Tank. Both 2.5-inch frangible nuts must function to complete safe separation. The 2.5-inch frangible nut contains two explosive boosters containing RDX explosive each capable of splitting the nut in half, on command from the Orbiter computers. To ensure separation, the boosters are designed to be redundant. The detonation of one booster is sufficient to split the nut in half. However, beginning in 1987 some production lots of 2.5-inch frangible nuts have demonstrated an inability to separate using only a single booster. The cause of the failure has been attributed to differences in the material properties and response of the Inconel 718 from which the 2.5-inch frangible nut is manufactured. Subsequent tests have resulted in design modifications of the boosters and frangible nut. Model development and initial analysis was conducted by Sandia National Laboratories (SNL) under funding from NASA Lyndon B. Johnson Space Center (NASA-JSC) starting in 1992. Modeling codes previously developed by SNL were transferred to NASA-JSC for further analysis on this and other devices. An explosive bolt with NASA Standard Detonator (NSD) charge, a 3/4-inch frangible nut, and the Super*Zip linear separation system are being modeled by NASA-JSC.
The composition of material condensed in the outer solar system is very dependent on the state of carbon and oxygen in the solar or circumplanetary nebula, since oxygen is the dominant solid-forming element in a solar composition gas (in the form of silicates and water ice), and carbon is about half as abundant. Past discussions of solid material formed in these regions have focused on differences expected between material formed near giant planets where carbon is generally expected to be in the reduced, CH4, form and material formed in the outer protoplanetary solar nebula where CO is believed to be the dominant form [1]. The composition and expected density of these materials are quite sensitive to the C and O solar abundances in all these models. We discuss here the effects of recently suggested modifications to solar abundances on the interpretation of the mean densities for satellites in the Saturn system.
Heat transfer in high-temperature, high-porosity, flexible refractory ceramic fibrous insulation felts is investigated. Heat transfer in these insulation materials consists of combined gas conduction, solid conduction, and radiation modes, with the precise theoretical modeling of the latter two modes being formidable. A semi-empirical model that requires inverse methods and steady-state thermal test data to infer some of the required model parameters is further developed in this study, and applied to five insulation materials for temperatures between 300 K and 1900 K. The steady-state thermal test setup at NASA Langley Research Center with recent modifications to increase its testing capability to 1900 K is discussed. Design considerations to ensure one-dimensional heat transfer in the test setup are described. Test data and corresponding thermal models for alumina and zirconia-based fibrous insulation felts are presented. Furthermore, test data and thermal models on two fibrous insulation samples containing additives to further suppress either radiation or gas conduction modes of heat transfer are presented. Previously published alumina-based insulation data are also re-processed using the updated modeling methodology. The significance of various heat transfer modes in typical insulation samples is discussed and used to provide general guidance on optimum insulation layups.
The paper discusses the phase equilibria for the ternary systems NiAlCr, NiAlMo, and NiAlW, with emphasis on reactions from the liquid state, although some of the solid state reactions are mentioned. It is shown that eutectics in the Ni-Al-refractory element (Cr, Mo, W) systems offer the potential for high-temperature turbine blade and vane applications. In particular, it is shown that the phase diagrams of these ternary systems can be manipulated to alter the eutectic phases and morphologies by simple quaternary alloying modifications. The resultant combination of chemistry and structure can be controlled to ensure a behavior that is well-matched to hot section component materials requirements.
Lunar sample measurements were made both under ambient nitrogen pressure and under vacuum conditions. Average emittance values were analyzed for a number of samples which were determined to include silicate minerals, pyroxenes, and fine particle feldspar. Information is also provided on modifications made to emittance apparatus in order to work with smaller sample sizes and to prevent accidental loss or contamination of the lunar sample material.
Although graphite fibers behave in an essentially elastic manner, the polymeric matrix of graphite/epoxy composites is a viscoelastic material which exhibits creep and delayed failures. The creep process is quite slow at room temperature, but may be accelerated by higher temperatures, moisture absorption, and other factors. Techniques are being studied to predict long-term behavior of general laminates based on short-term observations of the unidirectional material at elevated temperatures. A preliminary numerical procedure based on lamination theory is developed for predicting creep and delayed failures in laminated composites. A modification of the Findley nonlinear power law is used to model the constitutive behavior of a lamina. An adaptation of the Tsai-Hill failure criterion is used to predict the time-dependent strength of a lamina. Predicted creep and delayed failure results are compared with typical experimental data.
The development of the AGT 100 turbine components in structural ceramic materials is described. Development is defined as the complete and iterative cycle from design, analysis, test, and design refinement culminating in successful demonstration of the design requirements. The components are analyzed by a linear elastic probabilistic approach, which involves finite element (three- and/or two-dimensional) simulation of the component combined with a Weibull characterization of the brittle ceramic material strength distribution to calculate a probability of survival for the component in the operating environment. Component test failure investigation has resulted in design modifications, and an improvement in component reliability has been demonstrated. Engine testing (over 570 h to date) continues to assess design/development of structural ceramic components.
The goal of this program was the development of a SiC CVD growth of films thick enough to be useful as pseudo-substrates. The cold-walled CVD system was designed, assembled, and tested. Extrapolating from preliminary evaluation of SiC films grown in the system at relatively low temperatures indicates that the growth rate at the final temperatures will be high enough to make our approach practical. Modifications of the system to allow high temperature growth and cleaner growth conditions are in progress. This program was jointly funded by Wright Laboratory, Materials Directorate and NASA LeRC and monitored by NASA.
Polystyrene latex (PSL) microspheres have been utilized as seed material for flow visualization in wind tunnels. However, PSL microspheres have been observed to strongly adhere to wind tunnel and model surfaces. Surface contamination on the cleaning screens that remove vorticity and provide laminar flow in the test section, is particularly problematic. Agglomeration of particles on these screens cause constriction of the airflow through the screen resulting in inconsistent airflow properties in the test section. The adhesion mechanism of PSL microspheres to wind tunnel screens and 316 stainless steel flat plates, were evaluated in a contamination apparatus where small sections of screen material were exposed to PSL-seeded airflow. Using a design of experiments (DOE) methodology airflow seeding parameters were changed to evaluate how these modifications affected the degree of surface contamination. The solution composition, comprised of ethanol and water, was determined to be the most significant factor in particle adhesion. Utilizing image analysis software, data were collected from the contaminated surfaces and incorporated to generate predictive particle contamination models. A relationship was identified between the solvent evaporation rate, and the morphology and magnitude of PSL contaminants on the test surfaces. This analysis can be extended to other solvent mixtures to provide insight into simultaneously improving wind tunnel testing capabilities while diminishing facility contamination.
Space crop production research approaches and technologies can be validated for microgravity using parabolic or suborbital flight opportunities, and this will save considerable risk, time, and money for implementing new strategies in spaceflight. While the durations of microgravity in these tests are insufficient to grow crops, there are numerous examples of the value of microgravity testing for subsystems such as plant water and nutrient delivery, where multiphase fluid flow can be elucidated in short durations, and horticultural operations, such as harvesting and produce sanitation where containment and contamination can be assessed. Containment in any operational test is essential, as crop operations involve fluids and biological samples, which are potential hazards. This project consists of designing, developing, and constructing a parabolic/suborbital glovebox for experiment containment. The design involves modifications and upgrades to an existing glovebox developed at the University of Louisville. The University of Louisville glovebox was used by KSC researchers for space crop parabolic flight tests in 2021, and lessons learned from that testing have driven design modifications and improvements in the KSC-generated glovebox. Requirements were identified, parts were ordered, an operational science glovebox was fabricated, and a detailed materials specification list was generated. Analyses that are required for flight, remain to be performed to meet airworthiness requirements, and that work will have to be conducted in the future before use in flight.