SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Jet and core noise can be reduced and flame lengths may be significantly decreased when exhaust gases are caused to rotate or swirl about longitudinal axis of exhaust. Combustion in rotating flows is steady and quiet, and is not accompanied by pulsations or violent fluctuations.
Miniaturized transducers are fabricated from commercially available four-arm semiconductor gages; transducers are connected as bridge circuit and mounted on internal face of small diaphragm. Jacket made of conductive plastic may be needed to avoid buildup or static charges.
The effect of aircraft operational techniques in the terminal area on community noise impact of future short-haul aircraft was investigated. These operational techniques affected altitude, flap retraction rate, thrust cutback altitude, amount of thrust cutback, and amount of turning. During landing the parameters varied were glide slope angle, change in slope angle (two segment approach), and flap extension rate. One mechanical-flap (MF) aircraft and one externally-blown-flap (EBF) aircraft were used to study by noise impact at four U.S. airports, Hanscom Field (Boston); Washington National; Midway (Chicago); and Orange County (California). With the exception of Washington National (DCA), the study showed that a reduction of approximately 40 percent in the number of people highly annoyed (as defined in the study) can be obtained by using these operational techniques. At DCA the number of people highly annoyed using the standard procedure was quite low, but it is significant that the minimumimpact case for Runway 36 reduced the number of people highly annoyed to zero using a power cutback and a turning departure path. The evaluation procedures and methodology developed in this study represents an advance in acoustical state-of-the-art and should provide an effective and useful tool for determining aircraft noise impact upon the airport community.
The existing theory of subset regression is examined, taking into account optimality criteria, small experiments, nonlinear models, colinearities, and special techniques. Approaches based on chain pooling coupled with principal components regression are discussed, giving attention to a comparison of half-normal plotting with chain pooling, a procedure based on prior ordering, deletion under the F-test, the largest of a set of chi-square variates, and principal components regression and model deletion. The choice of a true (population) model for simulations is considered along with the evaluation of the decision procedure and suitable computer programs.
Explore the source record for details and available documents.
An existing fan stage, redesigned to reduce stator lift fluctuations, was acoustically tested for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator chord, adjusting incidence angles, and by adjusting the rotor velocity diagrams. The experiments showed significantly reduced broadband noise levels in the middle to high frequencies. Blade passage tone power was not reduced, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.
Explore the source record for details and available documents.
An existing fan stage, redesigned to reduce stator lift fluctuations, was acoustically tested for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator chord, adjusting incidence angles, and by adjusting the rotor velocity diagrams. The experiments showed significantly reduced broadband noise levels in the middle to high frequencies. Blade passage tone power was not reduced, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.
Exploratory concepts are described which were investigated to achieve a reduction in the vortex induced rolling upsets produced by heavy aircraft trailing vortexes. The initial tests included the use of mass injection, oscillating devices, wingtip shape design, interacting multiple vortexes, and end plates. Although later refinements of some of these concepts were successful, initial test results did not indicate a capability of these concepts to significantly alter the vortex induced rolling upset on a following aircraft.
A survey was made of research on the alleviation of the trailing vortex hazard by altering span loading with flaps on the generator airplane. Flap configurations of the generator that shed multiple vortices were found to have wakes that dispersed by vortex merging and sinusoidal instability. Reductions of approximately 50 percent in both the wake rolling moment imposed on a following aircraft and the aircraft separation requirement were achieved in the ground based and flight test experiments by deflecting the trailing edge flaps more inboard than outboard. Significantly, this configuration did not increase the drag or vibration on the generating aircraft compared to the conventional landing configuration. Ground based results of rolling moment measurement and flow visualization are shown, using a water tow facility, an air tow facility, and a wind tunnel. Flight test results are also shown, using a full scale B-747 airplane. General agreement was found among the results of the various ground based facilities and the flight tests.
A computer program for studying linear ocean wave refraction is described. The program features random-access modular bathymetry data storage. Three bottom topography approximation techniques are available in the program which provide varying degrees of bathymetry data smoothing. Refraction diagrams are generated automatically and can be displayed graphically in three forms: Ray patterns with specified uniform deepwater ray density, ray patterns with controlled nearshore ray density, or crest patterns constructed by using a cubic polynomial to approximate crest segments between adjacent rays.
The optimum acquisition sweep strategy was determined for a PN code despreader when the a priori probability density function was not uniform. A psuedo noise spread spectrum system was considered which could be utilized in the DSN to combat radio frequency interference. In a sample case, when the a priori probability density function was Gaussian, the acquisition time was reduced by about 41% compared to a uniform sweep approach.
New, and considerably altered, optimum dimensions for solar-cell metallization patterns are found using the recently developed procedure whose optimization criterion is the minimum cost-per-watt effect on the entire photovoltaic system. It is also found that the optimum shadow fraction by the fine grid is independent of metal cost and resistivity as well as cell size. The optimum thickness of the fine grid metal depends on all these factors, and in familiar cases it should be appreciably greater than that found by less complete analyses. The optimum bus bar thickness is much greater than those generally used. The cost-per-watt penalty due to the need for increased amounts of metal per unit area on larger cells is determined quantitatively and thereby provides a criterion for the minimum benefits that must be obtained in other process steps to make larger cells cost effective.
The paper describes an optimization method and some applications in which the design criterion for every part of a photovoltaic system is the minimum power cost for the complete system. The various parts of a photovoltaic system are grouped so that all costs fall into four classes: fabrication steps of the active solar cells; steps associated with the collector array and its complete structure; power-handling elements such as switchgear, storage, etc.; and fixed costs that do not vary directly with any of the system parts, such as factory-level overhead. It is assumed that the total collector area is independent of any of the optimization processes. A general equation is found to be capable of optimizing all parts of a system, although the cell and array steps are basically different from the power-handling elements. It is shown that the optimization of any step in the system requires inclusion of the properties of the other parts of the system.
Existing techniques were used to assess the noise impact on a community due to aircraft operation and to optimize the flight paths of an approaching aircraft with respect to the annoyance produced. Major achievements are: (1) the development of a population model suitable for determining the noise impact, (2) generation of a numerical computer code which uses this population model along with the steepest descent algorithm to optimize approach/landing trajectories, (3) implementation of this optimization code in several fictitious cases as well as for the community surrounding Patrick Henry International Airport, Virginia.
An expression for the phase error in the aperture plane of a spherical reflector was developed. The nature of this phase error over the aperture plane is discussed, and, to illustrate the usage of the expression, examples are given.
The author has identified the following significant results. The minimum entropy model may provide several useful advantages over traditional techniques for processing LANDSAT data. Total computer time to conduct a complete pattern recognition process is reduced. Subjective (transformed image), as well as statistically derived information is made available to the analyst/user much earlier in the analysis process. A rapid feedback loop in which numerous training set combinations can be tested for difference and representativeness is available. Additional tests of LANDSAT data processing using the minimum entropy model are clearly justified.
Explore the source record for details and available documents.