Search NASA⌕ Search

SEARCH · Search NASA

Results for “optimization techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Soft Actor Critic Based Volt-VAR Co-optimization in Active Distribution Grids

Modern distribution networks are undergoing several technical challenges, such as voltage fluctuations, because of high penetration of distributed energy resources (DERs). This paper proposes a deep reinforcement learning (DRL)-based Volt VAR co-optimization technique for reducing voltage fluctuations as well as power loss under high penetration of DERs. In addition, the proposed approach minimizes the operational cost of the grid. A stochastic policy optimization based soft actor critic (SAC) agent is proposed to configure the optimal set-points of the reactive power outputs of the inverters. The performance of the proposed model is verified on the modified IEEE 34- and 123-bus systems and compared with a base case scenario with no reactive supply by inverters, and a local droop control approach. The results demonstrate that the proposed framework outperforms the conventional droop control method in improving the voltage profile, minimizing the network power loss, and reducing grid operational cost.

—Distribution grids, deep reinforcement learning, ↗
DOE OSTI2025

Phase-Imaging Ion-Cyclotron-Resonance mass spectrometry with the Canadian Penning Trap at CARIBU

The Canadian Penning Trap mass spectrometer (CPT) has conducted precision mass measurements of neutron-rich nuclides from the CAlifornium Rare Isotope Breeder Upgrade (CARIBU) of the Argonne Tandem Linac Accelerator System (ATLAS) facility at Argonne National Laboratory using the Phase-Imaging Ion-Cyclotron-Resonance (PI-ICR) technique for over half a decade. Here, in this study, we discuss the CPT system, and methods to improve accuracy and precision in mass measurement using PI-ICR including some optimization techniques and recently studied systematic effects.

Penning trap mass spectrometry↗
DOE OSTI2023

Training material models using gradient descent algorithms

High temperature design requires accurate constitutive models to describe material inelastic deformation and failure behavior. Oftentimes, calibrating accurate models devolves into the problem of fitting the model parameters against experimental test data. Here, we present the pyopmat package, an open source framework for calibrating constitutive models against experiment data subjected to various loading conditions using machine learning techniques. The package calculates the exact gradient of the model response with respect to the parameters using a combination of automatic differentiation and the adjoint method. Given this exact gradient, we compare the performance of several gradient-based optimization techniques in fitting realistic constitutive models against data. Here, we demonstrate the efficiency and accuracy of our package through example problems using both synthetic data, generated using known parameter sets, under monotonic and cyclic loading conditions and also with an example applying the techniques developed here to actual high temperature creep-fatigue test data.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

On The Incorporation of Both Function-Driven Requirements and Topology Optimization in The Development of Lunar Launch & Landing Pads

In the design of additively manufactured structures, there can be a constant battle between focusing on function-driven design and topology optimization in an attempt to improve a products ability to meet all requirements. Function-driven optimization is defined as the process of identifying the best design parameters that satisfy project functionality requirements. Function-driven optimization is typically implemented by a designer(s) who, instead of computational limitations, has human bias for the input or inputs determined. On the other hand, topology optimization is defined as a mathematical method that optimizes material layout within a given design space, for a given set of loads, boundary conditions, and constraints with the goal of maximizing the performance of the system. In topology optimization, the work is defined by the limited mathematical inputs and computationally available goals/restraints. If not evaluated simultaneously, these two approaches can result in fundamentally different design concepts meant to address the same requirements. NASA’s Artemis program includes the development of a base camp near the lunar South Pole. After site selection is made, one of the first infrastructure elements needed will be a launch and landing pad (LLP). The construction of such a pad will prevent damage to nearby structures from plume-surface interaction (PSI) while also providing a stable platform for the lander. These benefits reduce the required distance between the established landing zones and other settlement infrastructure. In this paper, the authors evaluate the requirements associated with lunar LLP development, application of both functional and topological optimization techniques, methodologies to combine the two techniques, and potential impacts on final design of such a pad.

In-situ↗
NASA NTRS1978

Synthesis of aircraft structures using integrated design and analysis methods

A systematic research is reported to develop and validate methods for structural sizing of an airframe designed with the use of composite materials and active controls. This research program includes procedures for computing aeroelastic loads, static and dynamic aeroelasticity, analysis and synthesis of active controls, and optimization techniques. Development of the methods is concerned with the most effective ways of integrating and sequencing the procedures in order to generate structural sizing and the associated active control system, which is optimal with respect to a given merit function constrained by strength and aeroelasticity requirements.

Sobieszczanski-Sobieski, J.↗
NASA NTRS1987

Simultaneous structure/control optimization of large flexible spacecraft

This paper presents an approach to the simultaneous optimal design of a structure and control system for large flexible spacecrafts based on realistic objective function and constraints. The weight or total cost of structure and control system is minimized subject to constraints on the magnitude of response to a given disturbance involving both rigid-body and elastic modes. A nested optimization technique is developed to solve the combined problem. As an example, simple beam-like spacecraft under a steady-state white-noise disturbance force is investigated and some results of optimization are presented. In the numerical examples, the stiffness distribution, the location of controller and the control gains are optimized. Direct feedback control and linear quadratic optimal control laws are used with both inertial and non-inertial disturbing force. It is shown that the total cost is sensitive to the overall structural stiffness so that a simultaneous optimization of the structure and control system is indeed useful.

Onoda, Junjiro↗
NASA NTRS1987

An approach to structure/control simultaneous optimization for large flexible spacecraft

This paper presents an approach to the simultaneous optimal design of a structure and control system for large flexible spacecrafts based on realistic objective function and constraints. The weight or total cost of structure and control system is minimized subject to constraints on the magnitude of response to a given disturbance involving both rigid-body and elastic modes. A nested optimization technique is developed to solve the combined problem. As an example, simple beam-like spacecraft under a steady-state white-noise disturbance force is investigated and some results of optimization are presented. In the numerical examples, the stiffness distribution, location of controller, and control gains are optimized. Direct feedback control and linear quadratic optimal controls laws are used with both inertial and noninertial disturbing force. It is shown that the total cost is sensitive to the overall structural stiffness, so that simultaneous optimization of the structure and control system is indeed useful.

Onoda, Junjiro↗
NASA NTRS2002

Annual Research Briefs, 2002: Center for Turbulence Research

Turbulent combustion remains the largest component of the CTR's core program. This program and several related activities at CTR are supported by NASA's Ultra Efficient Engine Technology Program. It is also intimately connected with the Department of Energy's ASCI program at Stanford which develops the technology for numerical simulation of realistic aircraft engines using state of the art massively parallel computers. In combustion modeling the attention has been directed to the modeling of higher levels of complexity such as spray dynamics, radiation and soot formation. Major aircraft engine manufacturers have shown considerable interest in this program; in particular, a significant active collaboration exists between CTR and the Pratt & Whitney Corporation. CTR's combustion program is essentially based on the large-eddy simulation technique, LES, which is actively being pursued at CTR for this and many other applications. Important accomplishments in LES included simulations with three-dimensional filters which result in grid independent calculations (that is why we call it "true" LES), and the development of the methodology for integration of LES and Reynolds Averaged computations. Optimization techniques are being studied and used for the important problem of wall boundary conditions for LES as well as for optimal shape design for aeroacoustic and aerodynamic performance gains.

ULTRA EFFICIENT ENGINE TECHNOLOGY↗
DOE OSTI2023

Leveraging Application Data Constraints to Optimize Database-Backed Web Applications

Exploiting the relationships among data is a classical query optimization technique. As persistent data is increasingly being created and maintained programmatically, prior work that infers data relationships from data statistics misses an important opportunity. We present Coco, the first tool that identifies data relationships by analyzing database-backed applications. Once identified, Coco leverages the constraints to optimize the application's physical design and query execution. Instead of developing a fixed set of predefined rewriting rules, Coco employs an enumerate-test-verify technique to automatically exploit the discovered data constraints to improve query execution. Each resulting rewrite is provably equivalent to the original query. Using 14 real-world web applications, our experiments show that Coco can discover numerous data constraints from code analysis and improve real-world application performance significantly.

Computer Science↗
NASA NTRS2008

Investigation of an Anomaly Observed in Impedance Eduction Techniques

An intensive investigation into the cause of anomalous behavior commonly observed in impedance eduction techniques is performed. The investigation consists of grid refinement studies, detailed evaluation of results at and near anti-resonance frequencies, comparisons of different model results with synthesized and measured data, assessment or optimization techniques, and evaluation or boundary condition effects. Results show that the root cause of the anomalous behavior is the sensitivity of the educed impedance to small errors in the measured termination resistance at frequencies near anti-resonance or cut-on of a higher-order mode. Evidence is presented to show that the common usage of an anechoic, plane wave termination boundary condition in ducts where the "true" termination is reflective may act as a trigger for these anomalies. Replacing the exit impedance boundary condition by an exit pressure condition is shown to reduce the anomalous results.

Watson, W. R.↗
NASA NTRS2019

Thermal Property Estimation of Fibrous Insulation: Heat Transfer Modeling and the Continuous Genetic Algorithm

Thermal properties of high-temperature fibrous insulation materials were estimated from transient thermal tests using an inverse heat transfer technique. Transient temperature data from an experimental set up was collected and a simple, one-dimensional numerical model was constructed to replicate the temperatures within the test assembly. The Continuous Genetic Algorithm optimization technique in conjunction with a numerical thermal model and transient test data was used to estimate coefficients of a functional representation of the thermal property. The thermal properties, i.e., thermal conductivity and specific heat, of an alumina insulation felt were estimated over the temperature range of 300 K to 1700 K at various constant static pressures in nitrogen gas and compared with published data. The resulting thermal property estimates were within 10% of published values over the entire temperature range at various pressures. The methodology, application, and results are presented.

Frye, Elora↗
NASA NTRSDate not supplied

Robust Design Under Uncertainty of Hypersonic Inlets

The objective of this work is to optimize scramjet inlet designs under uncertainty at multiple fidelity levels. Optimizations are performed for both deterministic and stochastic conditions. For stochastic conditions, robust design is used to minimize the variance in system performance in addition to optimizing mean system performance. Uncertainty quantification is performed using non-intrusive polynomial chaos. Comparisons are made between low-fidelity analysis and high-fidelity analysis, as well as deterministic optimization and robust optimization. Results indicate that the general design trend of previous inlet optimization techniques is recovered for the external compression portion of an inlet. For the internal compression portion of an inlet, when viscous effects become more significant and boundary layer separation becomes more likely, the optimal trend departs from previous results. Multifidelity uncertainty quantification methods are found to substantially reduce the computation time of robust design while obtaining results that nearly match those of high-fidelity analysis. Robust optimization is found to decrease the standard deviation of throat Mach number by up to 40% compared to deterministic optimization. Changes in the design variables and total turning that lead to robust scramjet inlets are identified and linked back to fundamental physical principles through the theta-beta-Mach function.

Hypersonic↗
DOE OSTI2021

Optimized Dispatch of Distributed Energy Resources for Resiliency and Power Quality Improvements at the Grid-Edge

Distributed Energy Resources (DERs) installed on low-voltage distribution systems, both utility-owned and nonutility owned may be employed to make improvements to system resiliency and power quality, in addition to simply serving load demand. By selectively dispatching active and reactive power from these existing DERs, improvements in voltage profiles and service availability during adverse events may be achieved. Further benefits can be gained by optimally choosing which DERs to dispatch power from, and the distribution of power from those DERs. For a given operating condition, using Linear Programming methods, optimal power dispatch values for individual DERs can be determined, while considering variables such as voltage gains, losses in the lines and the DERs, and DER reserve capacities. One such optimization technique is developed in this paper, and results from a real-time simulation study on a modified IEEE 13-bus distribution system with three DERs, are being presented. The operation of the optimized DER selection and dispatch algorithm is shown during normal operation of the transmission system when the DERs operate in grid-connected mode. Similar analyses can drive decision making during transmission system failure when the DERs operate in grid-forming or islanded mode.

Chowdhury, Prithwiraj Roy↗
NASA NTRS1989

On processing development for fabrication of fiber reinforced composite, part 2

Fiber-reinforced composite laminates are used in many aerospace and automobile applications. The magnitudes and durations of the cure temperature and the cure pressure applied during the curing process have significant consequences for the performance of the finished product. The objective of this study is to exploit the potential of applying the optimization technique to the cure cycle design. Using the compression molding of a filled polyester sheet molding compound (SMC) as an example, a unified Computer Aided Design (CAD) methodology, consisting of three uncoupled modules, (i.e., optimization, analysis and sensitivity calculations), is developed to systematically generate optimal cure cycle designs. Various optimization formulations for the cure cycle design are investigated. The uniformities in the distributions of the temperature and the degree with those resulting from conventional isothermal processing conditions with pre-warmed platens. Recommendations with regards to further research in the computerization of the cure cycle design are also addressed.

Hou, Tan-Hung↗
DOE OSTI2020

Automated Fitting of a Semi-empirical Multiphase Equation of State for Carbon

The equation of state (EOS) of carbon is important in high explosive, geophysical, and inertial confinement fusion applications. Within the semi-empirical Sesame framework, the EOS of each phase is represented by a sum of cold, vibrational, and thermal electronic Helmholtz free energy contributions. Each phase has ~5-10 independent parameters that are adjusted to reproduce single-phase data (e.g., thermal expansion, isothermal compression) as well as experimentally- and computationally- derived phase boundaries. Manual calibration of the full multiphase EOS is arduous. We present our progress in development of automated EOS parameterization based on minimization of an objective function. Here, this function encodes deviation of model EOS results from experimental/computational benchmarks. Optimization is implemented as a combination of global (particle swarm) and local optimization techniques.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Combined Dimensional and Topology Optimization of Interior Permanent Magnet Synchronous Machine Rotors Using a Permanent Magnet Function Interpolation Method

This paper presents a magneto-structural combined dimensional and topology optimization technique for interior permanent magnet synchronous machine (IPMSM) rotors. Dimensional changes to the permanent magnet (PM) location or size are accomplished by interpolating or projecting a smoothed Heaviside rectangular function representing the presence of PM material onto the IPMSM rotor design domain mesh. A density based Solid Isotropic with Material Penalization (SIMP) topology optimization approach is then used to vary the presence of electrical steel in mesh elements to form flux barriers around the PM. The proposed method enforces a defined shape for the PM without requiring the mesh in the design domain to be deformed. Three examples are presented to demonstrate the technique: two flat bar IPMSM and one V-shaped IPMSM.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Natural evolutionary strategies for variational quantum computation

Abstract Natural evolutionary strategies (NES) are a family of gradient-free black-box optimization algorithms. This study illustrates their use for the optimization of randomly initialized parameterized quantum circuits (PQCs) in the region of vanishing gradients. We show that using the NES gradient estimator the exponential decrease in variance can be alleviated. We implement two specific approaches, the exponential and separable NES, for parameter optimization of PQCs and compare them against standard gradient descent. We apply them to two different problems of ground state energy estimation using variational quantum eigensolver and state preparation with circuits of varying depth and length. We also introduce batch optimization for circuits with larger depth to extend the use of ES to a larger number of parameters. We achieve accuracy comparable to state-of-the-art optimization techniques in all the above cases with a lower number of circuit evaluations. Our empirical results indicate that one can use NES as a hybrid tool in tandem with other gradient-based methods for optimization of deep quantum circuits in regions with vanishing gradients.

Anand, Abhinav (ORCID:0000000280812310)↗
NASA NTRS2001

Discrete-State Simulated Annealing For Traveling-Wave Tube Slow-Wave Circuit Optimization

Algorithms based on the global optimization technique of simulated annealing (SA) have proven useful in designing traveling-wave tube (TWT) slow-wave circuits for high RF power efficiency. The characteristic of SA that enables it to determine a globally optimized solution is its ability to accept non-improving moves in a controlled manner. In the initial stages of the optimization, the algorithm moves freely through configuration space, accepting most of the proposed designs. This freedom of movement allows non-intuitive designs to be explored rather than restricting the optimization to local improvement upon the initial configuration. As the optimization proceeds, the rate of acceptance of non-improving moves is gradually reduced until the algorithm converges to the optimized solution. The rate at which the freedom of movement is decreased is known as the annealing or cooling schedule of the SA algorithm. The main disadvantage of SA is that there is not a rigorous theoretical foundation for determining the parameters of the cooling schedule. The choice of these parameters is highly problem dependent and the designer needs to experiment in order to determine values that will provide a good optimization in a reasonable amount of computational time. This experimentation can absorb a large amount of time especially when the algorithm is being applied to a new type of design. In order to eliminate this disadvantage, a variation of SA known as discrete-state simulated annealing (DSSA), was recently developed. DSSA provides the theoretical foundation for a generic cooling schedule which is problem independent, Results of similar quality to SA can be obtained, but without the extra computational time required to tune the cooling parameters. Two algorithm variations based on DSSA were developed and programmed into a Microsoft Excel spreadsheet graphical user interface (GUI) to the two-dimensional nonlinear multisignal helix traveling-wave amplifier analysis program TWA3. The algorithms were used to optimize the computed RF efficiency of a TWT by determining the phase velocity profile of the slow-wave circuit. The mathematical theory and computational details of the DSSA algorithms will be presented and results will be compared to those obtained with a SA algorithm.

Wilson, Jeffrey D.↗