SEARCH · Search NASA

Results for “oxygen doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Deposition and dielectric characterization of highly oriented V 2 O 5 thin films

The possibility of ferroelectricity in orthorhombic V 2 O 5 thin flms was investigated. Films were deposited via either a chemical solution deposition (CSD) route or by RF magnetron sputtering. Highly (001) oriented V 2 O 5 flms were achieved with both deposition routes at temperatures as low as 300°C. No evidence for ferroelectricity was observed, even in flms which had been doped to provide local nuclei for polarization reversal. Loss originated from mid-gap trap states stemming from oxygen vacancies that were observed with photoluminescence, supplemented by piezoresponse force microscopy measurements. Furthermore, these trap states may have helped mimic ferroelectricity in previous reports on V 2 O 5 .

36 MATERIALS SCIENCE↗

NASA NTRS1986

Zirconium, hafnium, and rare earth element partition coefficients for ilmenite and other minerals in high-Ti lunar mare basalts - An experimental study

Partition coefficients were determined for Gd, Lu, Hf and Zr among ilmenite, armalcolite, and synthetic high-Ti mare basaltic melts at temperatures from 1122 deg to 1150 deg, and at oxygen fugacities of IW x 10 exp 0.5, by in situ analysis with an electron microprobe, using samples doped to present concentration levels. Coefficients for Zr were also measured for samples containing 600-1600 ppm Zr using this microprobe. In addition, coefficients were determined for Hf and Zr between chromian ulvospinel and melt, for Hf between pigeonite and melt, and for Lu between olivine and melt by microprobe analysis of samples doped to present levels. Values measured using the microprobe were in agreement with the values measured by analyzing mineral separates from the same run products by isotope dilution. Coefficient values for ilmenite are less than 0.01 for the LREE, are around 0.1 for the HREE, and are several times greater than this for Zr and Hf.

Mckay, G.↗

DOE OSTI2021

Free energy difference to create the M-OH* intermediate of the oxygen evolution reaction by time-resolved optical spectroscopy

Theoretical descriptors differentiate the catalytic activity of materials for the oxygen evolution reaction by the strength of oxygen binding in the reactive intermediate created upon electron transfer. Recently, time-resolved spectroscopy of a photo-electrochemically driven oxygen evolution reaction followed the vibrational and optical spectra of this intermediate, denoted M-OH*. However, these inherently kinetic experiments have not been connected to the relevant thermodynamic quantities. Here we discover that picosecond optical spectra of the Ti-OH* population on lightly doped SrTiO 3 are ordered by the surface hydroxylation. A Langmuir isotherm as a function of pH extracts an effective equilibrium constant relatable to the free energy difference of the first oxygen evolution reaction step. Thus, time-resolved spectroscopy of the catalytic surface reveals both kinetic and energetic information of elementary reaction steps, which provides a critical new connection between theory and experiment by which to tailor the pathway of water oxidation and other surface reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2010

Fiber-Based Laser Transmitter for Oxygen A-Band Spectroscopy and Remote Sensing

A fiber-based laser transmitter has been designed for active remote-sensing spectroscopy. The transmitter uses a master-oscillator-power-amplifier (MOPA) configuration with a distributed feedback diode-laser master oscillator and an erbium-doped fiber amplifier. The output from the MOPA is frequency-doubled with a periodically poled nonlinear crystal. The utility of this single-frequency, wavelength-tunable, power-scalable laser has been demonstrated in a spectroscopic measurement of the diatomic oxygen A-band.

Stephen, Mark A.↗

DOE OSTI2021

W-induced morphological modification of NiFe layered double hydroxides as efficient electrocatalysts for overall water splitting

Layered double hydroxides (LDHs) are one of the most efficient electrocatalysts for water splitting due to their nanosheet features and compositional flexibilities. This work explored the impact of W precursor concentration (0 ~ 10 mM) on LDH morphologies and performance in hydrogen production. Using an electrodeposition W-doping process, W-induced NiFe LDHs (NiFeW-LDHs) were in-situ grown on carbon fiber papers for water splitting. A performance peak was found at a W doping of 5 mM with well-aligned nanosheets, which not only boosted the charge transfer ability and gas evolution but also offered more than a four-fold electrochemical surface area increase compared to film-like NiFe hydroxides. The NiFeW-LDHs exhibited remarkable performance compared to NiFe hydroxides, showing decreased overpotentials of 31 mV and 114 mV for the oxygen evolution reactions (OERs) and hydrogen evolution reactions (HERs) at 10 mA/cm 2 and -10 mA/cm 2 , respectively, in alkaline media. The performance enhancement at 5 mM W-doping was linked to the well-aligned NiFeW-LDH nanosheets; smaller, less-textured nanosheets were observed with lower or higher W precursor concentrations (2.5 mM or >7.5 mM), leading to inferior OER and HER performances. Hence, an appropriate W doping is crucial to generating the morphologies that contribute to the higher performance of NiFeW-LDHs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Coupling Anionic Oxygen Redox with Selenium for Stable High‐Voltage Sodium Layered Oxide Cathodes

Utilizing anion redox reaction is crucial for developing the next generation of high-energy density, low-cost sodium-ion batteries. However, the irreversible oxygen redox reaction in Na-ion layered cathodes, which leads to voltage fading and reduced overall lifespan, has hindered their practical application. In this study, selenium is incorporated as a synergistic redox active center of oxygen to improve the stability of Na-ion cathodes. The redesigned cathode maintains stable voltage by demonstrating reversible oxygen redox while significantly suppressing the redox activity of manganese. The anionic redox contribution capacity of the selenium-doped Na 0.6 Li 0.2 Mn 0.8 O 2 cathode remains as high as 84% after 50 cycles, while the pristine Na 0.6 Li 0.2 Mn 0.8 O 2 cathode experiences a reduction to 39% of its initial capacity. The X-ray photoelectron spectroscopy data and computational analysis further revealed that selenium doping participates in redox as Se +4/5 which stabilizes the charged state and increases the energy step for O─O dimerization, thus improving the stability and lifespan of Na 0.6 Li 0.2 Mn 0.8 O 2 cathodes. In conclusion, the findings highlight the potential of redox coupling design to address the issue of voltage fade caused by irreversible anionic redox.

25 ENERGY STORAGE↗

DOE OSTI2020

Bulk direct gap MoS2 by plasma induced layer decoupling

Bulk direct transition metal dichalcogenide (TMDC) may have an increased interlayer separation of at least 0.5, 1, or 3 angstroms more than its bulk value. The TMDC may be a bulk direct band gap molybdenum disulfide (MoS2) or a bulk direct band gap tungsten diselenide (WSe2). Oxygen may be between the interlayers. A device may include the TMDC, such as an optoelectronic device, such as an LED, solid state laser, a photodetector, a solar cell, a FET, a thermoelectric generator, or a thermoelectric cooler. A method of making bulk direct transition metal dichalcogenide (TMDC) with increased interlayer separation may include exposing bulk direct TMDC to a remote (aka downstream) oxygen plasma. The plasma exposure may cause an increase in the photoluminescence efficiency of the TMDC, more charge neutral doping, or longer photo-excited carrier lifetimes, as compared to the TMDC without the plasma exposure.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Stabilization of Catalytically Active Surface Defects on Ga-doped La–Sr–Mn Perovskites for Improved Solar Thermochemical Generation of Hydrogen

Solar thermochemical hydrogen (STCH) production from water splitting typically requires performing redox cycles at temperatures above 1200 °C to reduce and re-oxidize the bulk of a reversible material. Bulk processes such as oxygen vacancy formation and oxygen diffusion energies dictate the viability of a material for STCH. The surface plays an important role in the formation and destruction of vacancies and interacts with gas phase water and surface adsorbed species. These surface processes can lead to surface reconfigurations and even the formation of surface phases with stoichiometry and oxygen content very different from the bulk composition. Understanding in-situ the surface chemical state and its evolution under water splitting is important to design nonstoichiometric oxides capable of longer-lasting STCH generation at lower temperatures. In this work, we describe the water splitting active defect sites in LSM ((La 0.65 Sr 0.35 ) 0.95 MnO 3–δ ) and Ga-doped LSM ((La 0.6 Sr 0.4 ) 0.95 (Mn 0.8 Ga 0.2 )O 3–δ ) perovskites during Operando thermochemical water splitting conditions using ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) experiments at 800 °C under steam. We show that sub-stoichiometric La +3 in the oxygen-vacancy rich surface at operating conditions can be used to correlate surface water splitting activity and the creation of surface hydroxide intermediates. The addition of Ga in LSM is shown to drastically stabilize the surface chemical composition by preventing Sr segregation and stabilizing catalytically active surface defects that promote the binding of adsorbed hydroxides. Here, we use Operando AP-XPS quantification of metastable surface hydroxide intermediates (La(OH) 3 ) to determine the amount of catalytically active surface sites in LSM (2.9%) and in LSMG (7.8–8.1%, depending on the bulk oxidation state).

08 HYDROGEN↗

NASA NTRS2003

Material for surface-enhanced Raman spectroscopy, and SER sensors and method for preparing same

Metal-doped sol-gel materials, suitable for use as sensors for surface-enhanced Raman spectroscopic analysis for trace chemical detection, are produced by effecting gelation and solvent removal of a doped sol-gel under mild temperature conditions. At least in certain instances reaction and drying will desirably be effected in an oxygen-starved environment. The metal of the sol-gel material functions, when irradiated, to produce a plasmon field for interaction with molecules of an analyte in contact therewith, increasing by orders of magnitude Raman photons that are generate by excitation radiation, and the method allows matching of the metal and metal particle size to a wavelength of light (or incident radiation, e.g., laser radiation) to generate surface plasmons. The porosity of the sol-gel material dramatically increases the surface area, and thereby the amount of metal exposed for analyte interaction. The sensors provided may be in the form of glass vials, fiber optics, multi-well micro-sample plates, etc., having surface coatings of the doped sol-gel material, to provide sampling systems for use in a Raman instrument.

Farquharson, Stuart↗

DOE OSTI2025

Arsenic activation and compensation in single crystal CdTe bilayers

In state-of-the art polycrystalline CdTe photovoltaics, group-V dopant activation is about 2%. Low activation can create electronic defects and lead to recombination and band tail losses. To develop methods to overcome this limitation, dopant activation was systematically investigated using molecular beam epitaxy (MBE) grown single crystal bilayers of As-doped CdTe on undoped CdTe. Results suggest multiple paths for improved As-activation in polycrystalline CdTe-based devices. It was found that the carrier concentration in this MBE material saturated at ∼3 × 1016 cm−3, with high levels (>50%) of As-activation possible. High activation could be achieved with a post-growth activation temperature of ∼450 °C, when the initial doping level was below the saturation level. However, at typical polycrystalline As incorporation levels (>5 × 1016 cm−3), the excess As is inactive or compensating, requiring elevated temperatures (500–600 °C) to achieve high activation. Oxygen in the annealing ambient was detrimental, while the effect of CdCl2 in the ambient is more case-dependent. A 575 °C activation anneal was combined with a 450 °C CdCl2 treatment to better understand the implications for polycrystalline CdTe. Interestingly, on highly doped samples, processes ending with a high temperature step displayed high activation, while those ending at 450 °C significantly reduced the carrier concentration (with or without CdCl2 in the ambient). Low activation can be restored with another high temperature anneal, allowing reproducible toggling between high and low activation based on the final temperature. Photoluminescence revealed the presence of donor–acceptor pairs in the low activation state that appear to be associated with a compensating defect.

14 SOLAR ENERGY↗

NASA NTRS2020

Structural evolution, electrochemical kinetic properties, and stability of A-site doped perovskite Sr(1-x)Yb(x)CoO(3-δ)

Mixed ionic and electronic conducting (MIEC) perovskite SrCoO(3-δ) is a widely studied (electro)catalyst for the oxygen reduction reaction (ORR) and possesses different crystal structures at different temperatures. These temperature dependent phase transitions significantly impact the ordering of oxygen vacancies and electrochemical kinetic properties as well as the reliability of the related devices. Some of the crystal structures formed, e.g. hexagonal phases, turn out to be almost impermeable to oxygen gas. Therefore, it is important to stabilize the crystal structure of SrCoO(3-δ) that favors the ORR over a wide temperature range. Herein, the partial substitution of the A-site Sr with Yb is systematically studied, including synthesis, characterization and analysis of structural evolution, electrochemical kinetic properties, thermal stability, and stability in a CO2-containing atmosphere. The results indicate that Sr(0.90)Yb(0.10)CoO(3-δ) is able to stabilize the tetragonal crystal structure with less ordered oxygen vacancies, leading to polarization resistances of 0.051, 0.115 and 0.272 U sq.cm at 750, 700 and 650 °C, respectively, on symmetrical cells. Sr(0.90)Yb(0.10)CoO(3-δ) demonstrates a very stable surface oxygen vacancy distribution and electronic structure near oxygen vacancies but dissociation of adsorbed oxygen molecules into atomic oxygen is affected by surface Sr segregation, and polarization resistance degradation is mainly induced by surface Sr segregation. Furthermore, Sr(0.90)Yb(0.10)CoO(3-δ) exhibits excellent thermal stability as well as excellent recovery stability and improved polarization performance after a few pure air/CO2-containing air treatment cycles at 700 °C. However, a hysteresis behavior of polarization performance is observed at 650 °C during gas cycling treatment, which may cause long-term degradation of the Sr(0.90)Yb(0.10)CoO(3-δ) electrode. The different polarization behaviors during gas cycling treatment are induced by different sensitivities of the formed surface strontium carbonate and chemisorbed surface oxo-carbonaceous species to different operating temperatures.

electrochemical kinetic↗

DOE OSTI2023

Chromium Poisoning Mitigation Strategy in Strontium-Doped Lanthanum Manganite-Based Air Electrodes in Solid Oxide Fuel Cells

Abstract Chromium poisoning of the air electrode remains an obstacle to the long-term performance of solid oxide fuel cells (SOFCs). In Sr-doped LaMnO3 (LSM) air electrodes, the poisoning process results in two types of deposits, chromium oxide (Cr2O3), and Mn, Cr spinel (MnCr2O4). The former forms electrochemically and the latter forms via a chemical reaction. By applying a small anodic reverse bias, Cr2O3 deposits can be removed because their formation is electrochemical in nature. However, MnCr2O4 deposits remain because their formation is chemical, rather than electrochemical, in nature. In situ chemical decomposition of the Mn, Cr spinel was investigated as an alternate removal method as thermodynamics supports its decomposition into constituent oxides below ∼540 °C in pure oxygen. The spinel decomposition process was characterized using thermogravimetric and X-ray diffraction analyses. The experimentally determined rate of spinel decomposition was undetectable (very slow) with isolated MnCr2O4 powders. The addition of 10 mol% gadolinia doped ceria (GDC) and silver powders significantly increased the rate of decomposition. However, the rate is limited by the diffusion of oxygen through the decomposed oxide layer. Although one strategy may be the addition of GDC and silver to the LSM air electrode to enhance spinel decomposition, the more effective mitigation strategy would be to prevent the formation of MnCr2O4 spinel in the first place through the removal of the reactants: Cr2O3 via electrochemical cleaning and mobile Mn ions in the zirconia electrolyte by incorporating a diffusion barrier layer such as GDC between the air electrode and electrolyte.

Electrochemistry↗

DOE OSTI2024

Subnanometer Scale Mapping of Hydrogen Doping in Vanadium Dioxide

Hydrogen donor doping of correlated electron systems such as vanadium dioxide (VO 2 ) profoundly modifies the ground state properties. The electrical behavior of H x VO 2 is strongly dependent on the hydrogen concentration; hence, atomic scale control of the doping process is necessary. It is however a nontrivial problem to quantitatively probe the hydrogen distribution in a solid matrix. As hydrogen transfers its sole electron to the material, the ionization mechanism is suppressed. Here in this study, a methodology mapping the doping distribution at subnanometer length scale is demonstrated across a H x VO 2 thin film focusing on the oxygen-hydrogen bonds using electron energy loss spectroscopy (EELS) coupled with first-principles EELS calculations. The hydrogen distribution was revealed to be nonuniform along the growth direction and between different VO 2 grains, calling for intricate hydrogenation mechanisms. Our study points to a powerful approach to quantitatively map dopant distribution in quantum materials relevant to energy and information science

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1971

Behavior of lithium in irradiated solar cells.

The current state of the art in radiation resistant lithium-doped silicon solar cells is reviewed. Fabrication techniques are reviewed. Characteristics of lithium-doped cells are discussed. Behavior of lithium-doped cells during 1 MeV electron irradiation are studied for various types of cells. Effects of variations in lithium and oxygen concentration are shown and discussed. Capacitance measurements at various voltages, frequencies and temperatures are used to detect charges in lithium donor concentration and the formation of defects during irradiation. Physical models to explain the observed effects are presented.

Carter, J. R., Jr.↗

NASA NTRS1987

Effect of water on hydrogen permeability

Doping of hydrogen with CO and CO2 was developed to reduce hydrogen permeation in Stirling engines by forming a low permeability oxide coating on the inner surface of the heater head tubes. Although doping worked well, under certain circumstances the protective oxide could be chemically reduced by the hydrogen in the engine. Some oxygen is required in the hydrogen to prevent reduction. Eventually, all the oxygen in the hydrogen gas - whatever its source - shows up as water. This is the result of hydrogen reducing the CO, CO2, or the protective inner surface oxides. This water can condense in the engine system under the right conditions. If the concentration of water vapor is reduced to a low enough level, the hydrogen can chemically reduce the oxide coating, resulting in an increase in permeability. This work was done to define the minimum water content required to avoid this reduction in the oxide coating. The results of this testing show that a minimum of approximately 750 ppm water is required to prevent an increase in permeability of CG-27, a high temperature metal alloy selected for Stirling engine heater tubes.

Hulligan, David↗

DOE OSTI2020

Universal Approach to Fabricating Graphene-Supported Single-Atom Catalysts from Doped ZnO Solid Solutions

Single-atom catalysts (SACs) have attracted widespread interest for many catalytic applications because of their distinguishing properties. However, general and scalable synthesis of efficient SACs remains significantly challenging, which limits their applications. Here we report an efficient and universal approach to fabricating a series of high-content metal atoms anchored into hollow nitrogen-doped graphene frameworks (M-N-Grs; M represents Fe, Co, Ni, Cu, etc.) at gram-scale. The highly compatible doped ZnO templates, acting as the dispersants of targeted metal heteroatoms, can react with the incoming gaseous organic ligands to form doped metal-organic framework thin shells, whose composition determines the heteroatom species and contents in M-N-Grs. We achieved over 1.2 atom % (5.85 wt %) metal loading content, superior oxygen reduction activity over commercial Pt/C catalyst, and a very high diffusion-limiting current (6.82 mA cm -2 ). Both experimental analyses and theoretical calculations reveal the oxygen reduction activity sequence of M-N-Grs. Additionally, the superior performance in Fe-N-Gr is mainly attributed to its unique electron structure, rich exposed active sites, and robust hollow framework: This synthesis strategy will stimulate the rapid development of SACs for diverse energy-related fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Active Tuning of Optical Constants in the Visible–UV: Praseodymium-Doped Ceria—a Model Mixed Ionic–Electronic Conductor

Mixed ionic-electronic conductors offer chemical and electrical means for active tuning of their optical constants, e.g. with variations in oxygen non-stoichiometry in Pr 0.1 Ce 0.9 O 2-δ , enabling implementation of adaptive thin film optical devices. Here, we demonstrate in-situ chemo-tuning of the extinction coefficient in Pr 0.1 Ce 0.9 O 2-δ at elevated temperatures and provide a tuning model that treats the interdependence of mobile oxygen vacancies and small polarons coupled to variations in optically active praseodymium ions. Further, a new means for electro-tuning of the optical constants of mixed ionic-electronic conductors was demonstrated experimentally and modeled for Pr 0.1 Ce 0.9 O 2-δ thin films deposited on grid-like electrode structures. Modeling of non-steady state optical transmittance modulations in the latter allows for estimation of oxygen vacancy mobility that determines the switching speed of the device. Quenched-in values of nr and k to room temperature become nonvolatile, providing a modulation range in the extinction coefficient of Δk ~0.1 (change of ~800%) and in the refractive index of Δn r ~0.1 (relative to initial n r of ~2.35). Key figures of merit including, transmission optical modulation of ~0.04 per 1 mV nm -1 , switching energy per area of 670 pJ μm -2 and switching times of seconds, were demonstrated, with further improvements possible.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Enhanced Electrocatalytic and Cathode‐Electrolyte Interfacial Properties With a Pr‐Based Simple Perovskite/Ruddlesden‐Popper Nanocomposite Cathode in Protonic Ceramic Fuel Cells

The sluggish kinetics and poor stability of the oxygen reduction reaction (ORR) remain the primary bottleneck for achieving high performance in protonic ceramic fuel cells (PCFCs) at intermediate temperatures (400–650°C). In this work, a Pr-based nanocomposite cathode comprised of simple perovskite phase (PrNi 0.7 Co 0.3 O 3-δ ) and Ruddlesden-Popper phase (Co-doped Pr 4 Ni 3 O 10+δ ) is developed. Although PrNi 0.7 Co 0.3 O 3-δ solely stands as a good cathode with facile proton transfer, combining the superior catalytic activity against oxygen on the Ruddlesden-Popper phase boosts the ORR performance further. The designed nanocomposite cathode outperforms the simple perovskite cathode, attributed to enhanced oxygen absorption and surface diffusion with the Ruddlesden-Popper phase. A precursor-based cathode deposition technique is also developed to achieve cathode grain sizes of ∼100 nm. A single cell with the nanocomposite cathode delivers a peak power density of 1.38 W cm −2 at 650°C, among the highest in reported PCFCs with Pr-based cathodes, with a small degradation rate of 0.145 mV h −1 during 250 h stability test. Further investigation of cathode-electrolyte interface revealed interfacial PrO 2 phase formation, promoted by abundant Pr 6 O 11 in the nanocomposite precursor powder, thereby improving both ohmic resistance and stability. These findings highlight the effectiveness of the nanocomposite cathode and underscore its advantages on interfacial properties.

08 - HYDROGEN↗