Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

A data fusion algorithm for multi-sensor microburst hazard assessment

A recursive model-based data fusion algorithm for multi-sensor microburst hazard assessment is described. An analytical microburst model is used to approximate the actual windfield, and a set of 'best' model parameters are estimated from measured winds. The winds corresponding to the best parameter set can then be used to compute alerting factors such as microburst position, extent, and intensity. The estimation algorithm is based on an iterated extended Kalman filter which uses the microburst model parameters as state variables. Microburst state dynamic and process noise parameters are chosen based on measured microburst statistics. The estimation method is applied to data from a time-varying computational simulation of a historical microburst event to demonstrate its capabilities and limitations. Selection of filter parameters and initial conditions is discussed. Computational requirements and datalink bandwidth considerations are also addressed.

Wanke, Craig R.↗

Reliable Real-Time Solution of Parametrized Partial Differential Equations: Reduced-Basis Output Bound Methods

We present a technique for the rapid and reliable prediction of linear-functional outputs of elliptic (and parabolic) partial differential equations with affine parameter dependence. The essential components are (i) (provably) rapidly convergent global reduced basis approximations, Galerkin projection onto a space W(sub N) spanned by solutions of the governing partial differential equation at N selected points in parameter space; (ii) a posteriori error estimation, relaxations of the error-residual equation that provide inexpensive yet sharp and rigorous bounds for the error in the outputs of interest; and (iii) off-line/on-line computational procedures, methods which decouple the generation and projection stages of the approximation process. The operation count for the on-line stage, in which, given a new parameter value, we calculate the output of interest and associated error bound, depends only on N (typically very small) and the parametric complexity of the problem; the method is thus ideally suited for the repeated and rapid evaluations required in the context of parameter estimation, design, optimization, and real-time control.

Prudhomme, C.↗

TPSAS-NF1676L-13122-DND

An approach for assessing the delamination propagation and growth capabilities in commercial finite element codes was developed and demonstrated for the Virtual Crack Closure Technique (VCCT) implementations in ABAQUS?. The Double Cantilever Beam (DCB) specimen was chosen as an example. First, benchmark results to assess delamination propagation capabilities under static loading were created using models simulating specimens with different delamination lengths. Second, starting from an initially straight front, the delamination was allowed to propagate based on the algorithms implemented in the commercial finite element software. The load-displacement relationship obtained from the propagation analysis results and the benchmark results were compared. Good agreements could be achieved by selecting the appropriate input parameters, which were determined in an iterative procedure. A benchmark case to assess the fatigue growth prediction capabilities was also created. Input control parameters were varied to study the effect on the computed delamination growth. The benchmarks enabled the selection of the appropriate input parameters that yielded good agreements between the results obtained from the automated analysis and the benchmark results. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

Ronald Krueger↗

Loop Gain and Circuit Parameters for Residual Carrier Tracking in the Advanced DSN Block V Receiver

A circuit level analysis for residual carrier tracking of a deep space network signal by a proposed Block V receiver as conceived by the Receiver Advanced Development Team is presented. The objective is to aid the circuit designer in selection of loop parameters to achieve the required performance objectives. The topics specifically addressed are: (1) loop stability and gain requirements, (2) loop component parametric equations, and (3) phase detector technology.

Young, P. H.↗

MPS Solidification Model. Volume 2: Operating guide and software documentation for the unsteady model

The operation of solidification Model 2 is described and documentation of the software associated with the model is provided. Model 2 calculates the macrosegregation in a rectangular ingot of a binary alloy as a result of unsteady horizontal axisymmetric bidirectional solidification. The solidification program allows interactive modification of calculation parameters as well as selection of graphical and tabular output. In batch mode, parameter values are input in card image form and output consists of printed tables of solidification functions. The operational aspects of Model 2 that differ substantially from Model 1 are described. The global flow diagrams and data structures of Model 2 are included. The primary program documentation is the code itself.

Maples, A. L.↗

Effect of Electron Beam Freeform Fabrication (EBF3) Processing Parameters on Composition of Ti-6-4

The Electron Beam Freeform Fabrication (EBF3) process developed at NASA Langley Research Center was evaluated using a design of experiments approach to determine the effect of processing parameters on the composition and geometry of Ti-6-4 deposits. The effects of three processing parameters: beam power, translation speed, and wire feed rate, were investigated by varying one while keeping the remaining parameters constant. A three-factorial, three-level, fully balanced mutually orthogonal array (L27) design of experiments approach was used to examine the effects of low, medium, and high settings for the processing parameters on the chemistry, geometry, and quality of the resulting deposits. Single bead high deposits were fabricated and evaluated for 27 experimental conditions. Loss of aluminum in Ti-6-4 was observed in EBF3 processing due to selective vaporization of the aluminum from the sustained molten pool in the vacuum environment; therefore, the chemistries of the deposits were measured and compared with the composition of the initial wire and base plate to determine if the loss of aluminum could be minimized through careful selection of processing parameters. The influence of processing parameters and coupling between these parameters on bulk composition, measured by Direct Current Plasma (DCP), local microchemistries determined by Wavelength Dispersive Spectrometry (WDS), and deposit geometry will also be discussed.

Lach, Cynthia L.↗

An Implanted, Stimulated Muscle Powered Piezoelectric Generator

A totally implantable piezoelectric generator system able to harness power from electrically activated muscle could be used to augment the power systems of implanted medical devices, such as neural prostheses, by reducing the number of battery replacement surgeries or by allowing periods of untethered functionality. The features of our generator design are no moving parts and the use of a portion of the generated power for system operation and regulation. A software model of the system has been developed and simulations have been performed to predict the output power as the system parameters were varied within their constraints. Mechanical forces that mimic muscle forces have been experimentally applied to a piezoelectric generator to verify the accuracy of the simulations and to explore losses due to mechanical coupling. Depending on the selection of system parameters, software simulations predict that this generator concept can generate up to approximately 700 W of power, which is greater than the power necessary to drive the generator, conservatively estimated to be 50 W. These results suggest that this concept has the potential to be an implantable, self-replenishing power source and further investigation is underway.

Lewandowski, Beth↗

On the concept of varying influence radii for a successive corrections objective analysis

This paper discusses objective analysis techniques known as 'methods of successive corrections' which were introduced by Cressman (1959) and developed for the analysis of mesoscale weather systems by Barnes (1964 and 1973). Theoretical filter response characteristics of the Barnes method are compared for filter parameters set to retrieve the short wavelengths and then build in the long wavelengths. The accuracy of the method is judged by the ability of the filters to restore desired wavelengths and remove undesired wavelengths. It was found that no single selection of filter parameters for the two-pass Barnes method gives the best analysis for all wavelengths. A three-pass hybrid method is shown to reduce this problem.

Achtemeier, Gary L.↗

The parameters of a VCM test for the selection of space materials

Materials for space applications must have low outgassing rates at normal operating temperatures and the outgassing products should include a minimum of condensables at the temperatures of nearby surfaces. A screening method, developed years ago, consists of holding a material sample at 398 K (125 C) for 24 hours and measuring its percentage total mass loss (TML) and the percentage volatile condensable mass (VCM) accreted on a 298 K (25 C) collector. In general, the material is acceptable if the TML is less than 1 percent and the VCM is less than 0.1 percent. This paper presents an analysis of the test and its results. It shows that the results of TML and VCM can be used to provide data on outgassing rates and to derive an 'equivalent activation energy' for the material. The energy variables are needed for the calculation of pressure in compartments, the molecular contamination of critical surfaces, and other problems in molecular flow and surface physics. The analysis points out the criticality of the test and its limits with regards to the detection of condensables from certain materials.

Scialdone, J. J.↗

Global Sensitivity Analysis of Simulated Remote Sensing Polarimetric Observations Over Snow

This study presents a detailed theoretical assessment of the information content of passive polarimetric observations over snow scenes, using a global sensitivity analysis (GSA) method. Conventional sensitivity studies focus on varying a single parameter while keeping all other parameters fixed. In contrast, the GSA correctly addresses the covariance of state parameters across their entire parameter space, hence favoring a more correct interpretation of inversion algorithms and the optimal design of their state vectors. The forward simulations exploit a vector radiative transfer model to obtain the Stokes vector emerging at the top of the atmosphere for different solar zenith angles, when the bottom boundary consists of a vertically resolved snowpack of non-spherical grains. The presence of light-absorbing particulates (LAPs), either embedded in the snow or aloft in the atmosphere above in the form of aerosols, is also considered. The results are presented for a set of wavelengths spanning the visible (VIS), near-infrared (NIR), and shortwave infrared (SWIR) region of the spectrum. The GSA correctly captures the expected, high sensitivity of the reflectance to LAPs in the VIS–NIR and to grain size at different depths in the snowpack in the NIR–SWIR. With adequate viewing geometries, mono-angle measurements of total reflectance in the VIS–SWIR (akin to those of the Moderate Resolution Imaging Spectroradiometer, MODIS) resolve grain size in the top layer of the snowpack sufficiently well. The addition of multi-angle polarimetric observations in the VIS–NIR provides information on grain shape and microscale roughness. The simultaneous sensitivity in the VIS–NIR to both aerosols and snow-embedded impurities can be disentangled by extending the spectral range to the SWIR, which contains information on aerosol optical depth while remaining essentially unaffected when the same particulates are mixed with the snow. Multi-angle polarimetric observations can therefore (i) effectively partition LAPs between the atmosphere and the surface, which represents a notorious challenge for snow remote sensing based on measurements of total reflectance only and (ii) lead to better estimates of grain shape and roughness and, in turn, the asymmetry parameter, which is critical for the determination of albedo. The retrieval uncertainties are minimized when the degree of linear polarization is used in place of the polarized reflectance. The Sobol indices, which are the main metric for the GSA, were used to select the state parameters in retrievals performed on data simulated for multiple instrument configurations. Improvements in retrieval quality with the addition of measurements of polarization, multi-angle views, and different spectral channels reflect the information content, identified by the Sobol indices, relative to each configuration. The results encourage the development of new remote sensing algorithms that fully leverage multi-angle and polarimetric capabilities of modern remote sensors. They can also aid flight planning activities, since the optimal exploitation of the information content of multi-angle measurements depends on the viewing geometry. The better characterization of surface and atmospheric parameters in snow-covered regions advances research opportunities for scientists of the cryosphere and ultimately benefits albedo estimates in climate models.

remote sensing↗

Bayesian Inference in Satellite Gravity Inversion

To solve a geophysical inverse problem means applying measurements to determine the parameters of the selected model. The inverse problem is formulated as the Bayesian inference. The Gaussian probability density functions are applied in the Bayes's equation. The CHAMP satellite gravity data are determined at the altitude of 400 kilometer altitude over the South part of the Pannonian basin. The model of interpretation is the right vertical cylinder. The parameters of the model are obtained from the minimum problem solved by the Simplex method.

Kis, K. I.↗

Simplex GPS and InSAR Inversion Software

Changes in the shape of the Earth's surface can be routinely measured with precisions better than centimeters. Processes below the surface often drive these changes and as a result, investigators require models with inversion methods to characterize the sources. Simplex inverts any combination of GPS (global positioning system), UAVSAR (uninhabited aerial vehicle synthetic aperture radar), and InSAR (interferometric synthetic aperture radar) data simultaneously for elastic response from fault and fluid motions. It can be used to solve for multiple faults and parameters, all of which can be specified or allowed to vary. The software can be used to study long-term tectonic motions and the faults responsible for those motions, or can be used to invert for co-seismic slip from earthquakes. Solutions involving estimation of fault motion and changes in fluid reservoirs such as magma or water are possible. Any arbitrary number of faults or parameters can be considered. Simplex specifically solves for any of location, geometry, fault slip, and expansion/contraction of a single or multiple faults. It inverts GPS and InSAR data for elastic dislocations in a half-space. Slip parameters include strike slip, dip slip, and tensile dislocations. It includes a map interface for both setting up the models and viewing the results. Results, including faults, and observed, computed, and residual displacements, are output in text format, a map interface, and can be exported to KML. The software interfaces with the QuakeTables database allowing a user to select existing fault parameters or data. Simplex can be accessed through the QuakeSim portal graphical user interface or run from a UNIX command line.

Donnellan, Andrea↗

Distinguishing between CAT and non-CAT areas by use of discriminant function analysis

The investigation considered is concerned with a method in which a statistical approach is employed to determine algebraic functions involving selected synoptic-scale parameters which would indicate areas and altitudes of CAT in the stratosphere over the western U.S. The statistical approach selected is based on discriminant function analysis. The functions are determined from combinations of synoptic-scale parameters and stratospheric turbulence data. It was found in the investigation that there is a relationship between selected combinations of synoptic-scale parameters of the upper troposphere and lower stratosphere and stratospheric clear-air turbulence.

Clark, T. L.↗

Indirect synthesis of multidegree-of-freedom transient systems

The indirect synthesis method is developed and shown to be capable of leading a near-optimal design of multidegree-of-freedom and multidesign-element transient nonlinear dynamical systems. The basis of the approach is to select the open design parameters such that the response of the portion of the system being designed approximates the limiting performances solution. The limiting performance problem can be formulated as one of linear programming by replacing all portions of the system subject to transient disturbances by control forces and supposing that the remaining portions are linear as are the overall kinematic constraints. One then selects the design parameters that respond most closely to the limiting performance solution, which can be achieved by unconstrained curve-fitting techniques.

Chen, Y. H.↗

Physical and dynamical conditions in interstellar clouds

Techniques for measuring the local and global parameters that describe molecular clouds are presented and illustrated by selected results. The local parameters which characterize a given location in a cloud are gas kinetic temperature, dust temperature, total density, magnetic field strength, abundance of species i, volume cooling and heating rates for gas and dust, and the thermal and turbulent velocities. Global properties which characterize the cloud as a whole include the size expressed as a length or area, the orientation and shape, the mass, and the integrated heating and cooling rates. If the cloud as a whole is collapsing or rotating, then the collapse velocity and the rotational velocity or angular momentum are global properties. An intermediate class of parameters which shares features of local and global properties includes the column density of species i, the total column density, and the average density.

Evans, N. J., II↗

Bayesian inference in geomagnetism

The inverse problem in empirical geomagnetic modeling is investigated, with critical examination of recently published studies. Particular attention is given to the use of Bayesian inference (BI) to select the damping parameter lambda in the uniqueness portion of the inverse problem. The mathematical bases of BI and stochastic inversion are explored, with consideration of bound-softening problems and resolution in linear Gaussian BI. The problem of estimating the radial magnetic field B(r) at the earth core-mantle boundary from surface and satellite measurements is then analyzed in detail, with specific attention to the selection of lambda in the studies of Gubbins (1983) and Gubbins and Bloxham (1985). It is argued that the selection method is inappropriate and leads to lambda values much larger than those that would result if a reasonable bound on the heat flow at the CMB were assumed.

Backus, George E.↗

Analysis of the passive stabilization of the long duration exposure facility

The nominal Long Duration Exposure Facility (LDEF) configurations and the anticipated orbit parameters are presented. A linear steady state analysis was performed using these parameters. The effects of orbit eccentricity, solar pressure, aerodynamic pressure, magnetic dipole, and the magnetically anchored rate damper were evaluated to determine the configuration sensitivity to variations in these parameters. The worst case conditions for steady state errors were identified, and the performance capability calculated. Garber instability bounds were evaluated for the range of configuration and damping coefficients under consideration. The transient damping capabilities of the damper were examined, and the time constant as a function of damping coefficient and spacecraft moment of inertia determined. The capture capabilities of the damper were calculated, and the results combined with steady state, transient, and Garber instability analyses to select damper design parameters.

Siegel, S. H.↗