Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure sensor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Investigation of space shuttle vehicle 140C configuration orbiter (model 16-0) wheel well pressure loads in the Rockwell International 7.75 x 11 foot wind tunnel (OA143)

Experimental aerodynamic investigations were conducted on a sting mounted .0405-scale representation of the 140C outer mold line space shuttle orbiter configuration in the Rockwell International 7.75 x 11.00 foot low speed wind tunnel. The primary test objectives were to define the orbiter wheel well pressure loading and its effects on landing gear thermal insulation and to investigate the pressure environment experienced by both the horizontal flight nose probe and air vent door probes. Steady state and dynamic pressure values were recorded in the orbiter nose gear well, left main landing gear well, horizontal flight nose probe, and both left and right air vent door probe. All steady state pressure levels were measured by Statham differential pressure transducers while dynamic pressure levels were recorded by Kulite high frequency response pressure sensors.

Mennell, R. C.↗
NASA NTRS1976

A simple total energy sensor

This research concerns a simple technique for total energy compensation having the primary requirement of good compensation with a low cost, easy to make sensor. A comprehensive library search and a small wind tunnel were used to explore fundamentals and to develop a number of probes which were flight tested with satisfactory results. Simple probe configurations were tested using the characteristics of laminar flow separation around a small cylinder to produce a sensor pressure having the desired relationship between static and dynamic pressures. Wind tunnel and flight tests confirmed the concepts for a wide range of speeds, altitudes, and flow directions encountered in soaring. Data and findings are presented, along with a discussion of factors important to total energy compensation.

Nicks, O. W.↗
NASA NTRS1976

Compressor blade setting angle accuracy study, volume 1

The aerodynamic test of a small, single stage, highly loaded, axial flow transonic compressor is covered. The stage was modified by fabricating a 24 blade rotor with mis-set blades in a repeating pattern - two degrees closed from nominal, two degrees open from nominal and nominal. The unit was instrumented to determine overall performance and average blade element data. High-response, dynamic pressure probes were installed to record pressure patterns at selected points in the flowpath. Testing was conducted at speeds from 70 to 94% of design equivalent speed with a conventional casing and also with circumferential grooves over the rotor tip. Testing indicated severe performance penalties were incurred as a result of the mis-set blading. Lower flow, pressure ratio, and efficiency were observed for the stage with or without casing treatment. Periodic pressure variations were detected at every location where high response pressure sensors were located and were directly related to blading geometry.

Holman, F. F.↗
NASA NTRS1976

Biomedical technology transfer: Applications of NASA science and technology

The major efforts of the Stanford Biomedical Applications Team Program at the Stanford University School of Medicine for the period from October 1, 1975 to September 31, 1976 are covered. A completed EMG biotelemetry system which monitors the physiological signals of man and animals in space related research is discussed. The results of a pilot study involving lower body negative pressure testing in cardiac patients has been completed as well as the design and construction of a new leg negative pressure unit for evaluating heart patients. This technology utilizes vacuum chambers to stress the cardiovascular system during space flight. Laboratory tests of an intracranial pressure transducer, have been conducted. Extremely stable long term data using capacative pressure sensors has lead to the order of commercially manufactured monitoring systems base. Projects involving commercialization are: flexible medical electrodes, an echocardioscope, a miniature biotelemetry system, and an on-line ventricular contour detector.

Source record↗
NASA NTRS1977

Buffet characteristics of the F-8 supercritical wing airplane

The buffet characteristics of the F-8 supercritical wing airplane were investigated. Wing structural response was used to determine the buffet characteristics of the wing and these characteristics are compared with wind tunnel model data and the wing flow characteristics at transonic speeds. The wingtip accelerometer was used to determine the buffet onset boundary and to measure the buffet intensity characteristics of the airplane. The effects of moderate trailing edge flap deflections on the buffet onset boundary are presented. The supercritical wing flow characteristics were determined from wind tunnel and flight static pressure measurements and from a dynamic pressure sensor mounted on the flight test airplane in the vicinity of the shock wave that formed on the upper surface of the wing at transonic speeds. The comparison of the airplane's structural response data to the supercritical flow characteristics includes the effects of a leading edge vortex generator.

Deangelis, V. M.↗
NASA NTRS1977

Comparison of Estimated with Measured Maximum Instantaneous Distortion Using Flight Data from an Axisymmetric Mixed Compression Inlet

YF-12C flight-measured inlet dynamic distortion data are compared with predictions made on the basis of the method reported by Melick et al. (1976). The YF-12C aircraft is a twin engine aircraft capable of speeds above 3. The inlets have a translating spike to control the inlet throat area. A bypass system is used to control the terminal shock of the inlet for operation in the mixed compression mode. The dynamic data were obtained with the aid of 24 high frequency response total pressure sensors. The model of Melick et al. is discussed along with the computer program used to implement the model. It is found that the predictions of maximum instantaneous distortion are within 20 percent of the measured values, which had been obtained at Mach numbers of 1.8, 2.1, 2.5, and 3.0.

Brilliant, H. M.↗
NASA NTRS1977

Application of microelectronic technology to general aviation flight control

This paper presents several different methods that can be used to determine the aircraft orientation (attitude) without direct measurement. The methods combine state estimation techniques with measurements from solid state pressure sensors, accelerometers, and magnetometers to determine the aircraft state. The paper demonstrates how the estimation algorithms were validated and compared using flight test data, and it presents results of performance sensitivity analyses of sensor error, modeling inaccuracies, and wind disturbance effects on the attitude estimation errors. If implemented, the methods presented could make it possible to eliminate directional and vertical gyros and to change from many isolated sensors to an integrated, small, reliable sensing package for determining the aircraft state.

Sorensen, J. A.↗
NASA NTRS1979

Wideband EMG telemetry system

Miniature, individual crystal-controlled RF transmitters located in EMG pressure sensors simplifies multichannel EMG telemetry for electronic gait monitoring. Transmitters which are assigned operating frequencies within 174 - 216 MHz band have linear frequency response from 20 - 2000 Hz and operate over range of 15 m.

Rosatino, S. A.↗
NASA NTRS1978

Adaptation of ion beam technology to microfabrication of solid state devices and transducers

A number of areas were investigated to determine the potential uses of ion beam techniques in the construction of solid state devices and transducers and the packaging of implantable electronics for biomedical applications. The five areas investigated during the past year were: (1) diode-like devices fabricated on textured silicon; (2) a photolithographic technique for patterning ion beam sputtered PVC (polyvinyl chloride); (3) use of sputtered Teflon as a protective coating for implantable pressure sensors; (4) the sputtering of Macor to seal implantable hybrid circuits; and (5) the use of sputtered Teflon to immobilize enzymes.

Topich, J. A.↗
NASA NTRS1980

Viking Mars mission support investigations in the Langley transonic dynamics tunnel

Six experimental investigations conducted in the transonic dynamics tunnel, which supported elements of the entry and the landed phases of the Viking mission, are described. The objective of each investigation and selected experimental results are presented. How these particular wind tunnel results contributed to spacecraft development and ultimately to the success of the Viking mission is indicated. Experimental studies applicable to the entry phase of the mission included parachute environment and performance definition, aerodynamic characteristics exhibited by two separating bodies, and pressure measurements in the transonic range to optimize the location and orientation of a stagnation-pressure sensor on the Lander. The experimental investigations which supported the landed phase of the mission included a convective heat transfer test to establish the requirements for wind covers for the radioisotope thermoelectric generators and two tests which supported the development and calibration of the meteorological science experiment.

Foughner, J. T., Jr.↗
NASA NTRS1980

Downbursts and microbursts - An aviation hazard

Downburst and microburst phenomena occurring since 1975 are studied, based on meteorological analyses of aircraft accidents, aerial surveys of wind effects left behind downbursts, and studies of sub-mesoscale wind systems. It is concluded that microbursts beneath small, air mass thunderstorms are unpredictable in terms of weather forecast. Most aircraft incidents, however, were found to have occurred in the summer months, June through August. An intense microburst could produce 150 mph horizontal winds as well as 60 fps downflows at the tree-top level. The largest contributing factor to aircraft difficulties seemed to be a combination of the headwind decrease and the downflow. Anemometers and/or pressure sensors placed near runways were found effective for detecting gust fronts, but not for detecting downbursts. It is recommended that new detection systems placed on the ground or airborne, be developed, and that pilots be trained for simulated landing and go-around through microbursts.

Fujita, T. T.↗
NASA NTRS1980

An investigation of wave sheltering by islands

The results of SAR, HF radar, wave rider buoy, and pressure sensor studies of wave behavior around San Clemente Island off the coast of California are reported. The SAR operated at a frequency of 1.2 GHz corresponding to a wavelength of 25 cm at 25 m resolution. Imagery was corrected for the slant range distortion and two-dimensional fast Fourier transforms were used to obtain two-dimensional wave number spectra. A 1 MW source was employed for the HF radar, with a receiving antenna synthesized by mounting the receiver on a van which drove along straight stretches of an oceanside highway. The measurement of 77 m waves displayed a shadow effect after the island, with an unexpected recovery which implies local wave generation. Reflected energy was determined to be too weak to account for the waves, and a nonlinear transfer of wave energy from waves moving parallel to the island was concluded to be the source of the observed inner wave energy.

Hsiao, S. V.↗
NASA NTRS1982

Recent results about fan noise: Its generation, radiation and suppression

Fan noise including its generation, radiation characteristics, and suppression by acoustic treatment is studied. In fan noise generation, results from engine and fan experiments, using inflow control measures to suppress noise sources related to inflow distortion and turbulence, are described. The suppression of sources related to inflow allows the experiments to focus on the fan or engine internal sources. Some of the experiments incorporated pressure sensors on the fan blades to sample the flow disturbances encountered by the blades. From these data some inferences can be drawn about the origins of the disturbances. Also, hot wire measurements of a fan rotor wake field are presented and related to the fan's noise signature. The radiation and the suppression of fan noise are dependent on the acoustic modes generated by the fan. Fan noise suppression and radiation is described by relating these phenomena to the mode cutoff ratio parameter. In addition to its utility in acoustic treatment design and performance prediction, cutoff ratio was useful in developing a simple description of the radiation pattern for broadband fan noise. Some of the findings using the cutoff ratio parameter are presented.

Feiler, C. E.↗
NASA NTRS1981

Instrumentation applications to Space Shuttle models and thermal protection system tiles tested in NASA-AMES wind tunnels

The highlights of the many wind-tunnel tests conducted in the course of the Space Shuttle development program are presented with emphasis on instrumentation applications. The examples of tests discussed include airframe aerodynamics, aerodynamic heating, aerodynamic noise, tile dynamic response, and tile loads. Many of the tests were conducted with standard wind-tunnel instrumentation. Most of the more unusual instrumentation requirements were related to the thermal protection system, where some pressure-sensor concepts were adapted to measure airloads on tiles. These measurements provided the only quantitative data that could be used to confirm the airload analysis procedure. Limited applications of computers to experimental control, in conjunction with data taken during Shuttle tests, have resulted in substantial benefits in overall test efficiency.

Coe, C. F.↗
NASA NTRS1983

Integrated control system concept for high-speed aircraft

The synthesis and evaluation of flight control system architectures for future aircraft are discussed in terms of design features and the requirements for fighter aircraft. Advanced fighter configurations may feature canards, flaperons, two-dimensional vectoring nozzles, a mixing compression inlet, and an advanced turbojet engine. Survey and evaluation technology will also progress to include distributed microprocessors, VLSI and VHSIC microcircuitry, optical circuits, analytic redundancy, etc. Bottom-p and top-down architectures have been investigated to fulfill the reliability, maintainability, cost, and performance goals. A centralized architecture has been devised with line-removable units to facilitate maintainability and reduce weight. Descriptions are provided of the performance parameters and applications of optical elements, photoelastic pressure sensors, rare earth sensors, computing elements, and information transfer system.

Carlin, C. M.↗
NASA NTRS1984

Research pressure instrumentation for NASA Space Shuttle main engine, modification no. 5

The advantages of silicon piezoresistive strain sensing technology are being used to achieve the objectives of state of the art pressure sensors for SSME applications. The integration of multiple functions on a single chip is the key attribute being exploited. Progress is reported in transducer packaging and materials; silicon resistor characterization at cryogenic temperatures; chip mounting; and frequency response optimization.

Anderson, P. J.↗
NASA NTRS1984

Research pressure instrumentation for NASA Space Shuttle main engine, modification no. 5

The objective of the research project described is to define and demonstrate methods to advance the state of the art of pressure sensors for the space shuttle main engine (SSME). Silicon piezoresistive technology was utilized in completing tasks: generation and testing of three transducer design concepts for solid state applications; silicon resistor characterization at cryogenic temperatures; experimental chip mounting characterization; frequency response optimization and prototype design and fabrication. Excellent silicon sensor performance was demonstrated at liquid nitrogen temperature. A silicon resistor ion implant dose was customized for SSME temperature requirements. A basic acoustic modeling software program was developed as a design tool to evaluate frequency response characteristics.

Anderson, P. J.↗
NASA NTRS1984

Research pressure instrumentation for NASA Space Shuttle main engine

The development of prototype pressure transducers which are targeted to meet the Space Shuttle Main Engine SSME performance design goals is discussed. The fabrication, testing and delivery of 10 prototype units is examined. Silicon piezoresistive strain sensing technology is used to achieve the objectives of advanced state-of-the-art pressure sensors in terms of reliability, accuracy and ease of manufacture. Integration of multiple functions on a single chip is the key attribute of this technology.

Anderson, P. J.↗