Search NASA⌕ Search

SEARCH · Search NASA

Results for “proton beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of delta ray electrons on measurement uncertainties of harp system

A harp system, which is a multi-wire beam profile monitoring (MWPM) system, is planned upstream of the spallation target to make in situ calibration of beam current density configuration on the target along with beam imaging from luminescent coating on the beam entrance window at the Second Target Station (STS) of the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). This beam interception-based beam diagnostics system on the target will be used to ensure that the maximum beam loads on the target are within the design range during neutron production. Current design of the harp consists of three layers of measurement wires each of which is sandwiched between voltage biasing wire planes. The signal obtained from each measurement wire layer is disturbed by secondary electrons (SE) and delta rays produced by beam-matter interactions in neighboring wires and ionization of residual gases in accelerator vacuum. While the backgrounds from SE can be suppressed by voltage biasing, the delta-ray electrons with kinetic energies above keV ranges overcome the electric potential bias. In this paper, we study the effects of delta-rays on the measurement uncertainties of MWPM using the particle transport simulation code FLUKA. Furthermore, the cases where the harp system is installed in the proximity of a large delta ray sources such as proton beam window or in the core vessel filled with sub-atmospheric gas have been studied.

Lee, Yong Joong↗
NASA NTRS1992

Measurements of the radiation dose to LDEF by means of passive dosimetry

A very simple experiment was fielded on LDEF to measure the energetic radiation dose by means of passive dosimetry. It consisted of two identical packets of 16 LiF thermoluminescent dosimeters (TLD) arranged in planar arrays. One array was placed on the leading edge of the spacecraft, the other on the trailing edge. These arrays were installed in opaque packets of 1 mil Al foil and Kapton tape mounted behind an Al plate of 30 mils thickness. The nominal energy thresholds were 14 MeV for protons and 650 keV for electrons. In addition to the flight arrays, two control arrays were prepared which were kept with the flight arrays as long as possible during experimental integration and then stored in the lab. The flight and control arrays were read out alternating in groups of four; it was found that the control dose was negligible. The flight and control detectors were exposed to a 55 MeV proton beam in order to provide a recalibration of the detectors. It was found that the post-flight and pre-flight calibrations were in good agreement. A comparison of results with the prediction shows that the measured dose was a factor of 4 to 5 low. It is possible that there was in-flight annealing of the TLDs as a result of the long mission and perhaps temperature excursions of the sensors. The East-West effect was larger than expected. The ratio of 1.65 is approximately what was expected for the protons alone. Electrons should reduce the dose ratio since electrons add equally to the leading and trailing edge dose. A possible explanation is that the electron dose was negligible compared to the proton dose.

Blake, J. B.↗
NASA NTRS2003

A Comparison of Model Calculation and Measurement of Absorbed Dose for Proton Irradiation

With the increase in the amount of time spent EVA that is necessary to complete the construction and subsequent maintenance of ISS, it will become increasingly important for ground support personnel to accurately characterize the radiation exposures incurred by EVA crewmembers. Since exposure measurements cannot be taken within the organs of interest, it is necessary to estimate these exposures by calculation. To validate the methods and tools used to develop these estimates, it is necessary to model experiments performed in a controlled environment. This work is such an effort. A human phantom was outfitted with detector equipment and then placed in American EMU and Orlan-M EVA space suits. The suited phantom was irradiated at the LLUPTF with proton beams of known energies. Absorbed dose measurements were made by the spaceflight operational dosimetrist from JSC at multiple sites in the skin, eye, brain, stomach, and small intestine locations in the phantom. These exposures are then modeled using the BRYNTRN radiation transport code developed at the NASA Langley Research Center, and the CAM (computerized anatomical male) human geometry model of Billings and Yucker. Comparisons of absorbed dose calculations with measurements show excellent agreement. This suggests that there is reason to be confident in the ability of both the transport code and the human body model to estimate proton exposure in ground-based laboratory experiments.

Zapp, N.↗
DOE OSTI2020

Application of laser-driven capacitor-coil to target normal sheath acceleration

A laser-driven accelerator generates protons with tens of MeV in energy by a compact, strong, and transient accelerating electric field produced as a result of laser–plasma interactions at relativistic intensities. In previous studies, two- and three-dimensional particle-in-cell simulations revealed that the application of a kT-level axial magnetic field results in an enhancement of proton acceleration via the target normal sheath acceleration mechanism due to reduced lateral electron divergence and improved electron heating efficiency. An experimental investigation of this scheme on the GEKKO-XII and the LFEX facilities found that the number and maximum energy of the accelerated protons decreased with increasing the temporal delay between the pulse driving the external magnetic-field and the pulse accelerating the protons, contrary to the theoretical and numerical expectations. Finally, we identify sources responsible for the degradation of the proton beam performance and we propose an alternative experimental setup to mitigate the degradation in future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2002

Response of thyroid follicular cells to gamma irradiation compared to proton irradiation: II. The role of connexin 32

The objective of this study was to determine whether connexin 32-type gap junctions contribute to the "contact effect" in follicular thyrocytes and whether the response is influenced by radiation quality. Our previous studies demonstrated that early-passage follicular cultures of Fischer rat thyroid cells express functional connexin 32 gap junctions, with later-passage cultures expressing a truncated nonfunctional form of the protein. This model allowed us to assess the role of connexin 32 in radiation responsiveness without relying solely on chemical manipulation of gap junctions. The survival curves generated after gamma irradiation revealed that early-passage follicular cultures had significantly lower values of alpha (0.04 Gy(-1)) than later-passage cultures (0.11 Gy(-1)) (P < 0.0001, n = 12). As an additional way to determine whether connexin 32 was contributing to the difference in survival, cultures were treated with heptanol, resulting in higher alpha values, with early-passage cultures (0.10 Gy(-1)) nearly equivalent to untreated late-passage cultures (0.11 Gy(-1)) (P > 0.1, n = 9). This strongly suggests that the presence of functional connexin 32-type gap junctions was contributing to radiation resistance in gamma-irradiated thyroid follicles. Survival curves from proton-irradiated cultures had alpha values that were not significantly different whether cells expressed functional connexin 32 (0.10 Gy(-1)), did not express connexin 32 (0.09 Gy(-1)), or were down-regulated (early-passage plus heptanol, 0.09 Gy(-1); late-passage plus heptanol, 0.12 Gy(-1)) (P > 0.1, n = 19). Thus, for proton irradiation, the presence of connexin 32-type gap junctional channels did not influence their radiosensitivity. Collectively, the data support the following conclusions. (1) The lower alpha values from the gamma-ray survival curves of the early-passage cultures suggest greater repair efficiency and/or enhanced resistance to radiation-induced damage, coincident with the expression of connexin 32-type gap junctions. (2) The increased sensitivity of FRTL-5 cells to proton irradiation was independent of their ability to communicate through connexin 32 gap junctions. (3) The fact that the beta components of the survival curves from both gamma rays and proton beams were similar (average 0.022 +/- 0.008 Gy(-2), P > 0.1, n = 39) suggests that at higher doses the loss of viability occurs at a relatively constant rate and is independent of radiation quality and the presence of functional gap junctions.

Non-NASA Center↗
DOE OSTI2025

Neutron production and dosimetry with D(D,n) 3 He, 12 C(D,n) 13 N and 7 Li(p,n) 7 Be reactions at the Sandia Ion Beam Laboratory

Neutrons are produced at the Sandia Ion Beam Laboratory (IBL) using a beam of 280 keV D 2 + ions onto an erbium deuteride target. At test locations in the forward direction these neutrons have energies of about 2.9 MeV and a maximum flux on the flange of the test chamber of about 10 10 n/cm 2 /hour. Dosimetry is done by counting associated charged particles and by nickel foil activation dosimetry. Neutrons with higher energies, up to 6 MeV are produced using higher energy deuterium, up to 3 MeV, from the Pelletron ion accelerator at the IBL on a deuteride target. This report provides detailed information on the methods used for the production and dosimetry of neutrons by the D(D,n) 3 He nuclear reaction at the IBL. Neutron production by the 7 Li(p,n) 7 Be reaction with a proton beam from the Pelletron on a lithium target, such as LiF is also discussed. This produces neutrons with lower energy, in the range from about 0.1 to 1.3 MeV. Neutron production by the 12 C(D,n) 13 N reaction is also discussed. The purpose of this report is to provide information needed to test the effects of neutron irradiation on semiconductor materials and devices at the Sandia IBL.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A data-driven method to estimate the antiproton background in the Mu2e experiment

The Mu2e experiment at Fermilab will search for the Charged Lepton Flavour Violating (CLFV) process of coherent, neutrinoless µ− → e − conversion in the field of an aluminum nucleus. The expected signal is a monochromatic electron with the energy of 104.97 MeV, slightly below the muon rest mass. Observation of a CLFV process would provide unambiguous evidence for Beyond the Standard Model (BSM) physics. Mu2e is sensitive to a wide range of BSM models and has the capability to distinguish between them, guiding us towards the most accurate models. The key features of the Mu2e experiment are: (1) a high intensity pulsed negative muon beam with about 1010 stopped µ −/s, and (2) a sophisticated superconducting solenoid system with a gradient magnetic field to form and guide the intense muon beam to the target. The Mu2e physics data taking is expected to begin in 2027. For Run I, the expected 5σ discovery sensitivity is Rµe = 1.2 × 10−15, with a total expected background of 0.11 ± 0.03 events. In the absence of a signal, the expected upper limit is Rµe < 6.2 × 10−16 at 90% CL. The success of this experiment hinges on the accurate estimation of the background from various SM processes that could provide signal-like electrons. One of the background processes is antiprotons annihilating in the stopping target to produce signal like electrons through π0 → γγ decays followed by γ conversions, and π− → µ−ν¯ decays followed by µ− decay. It is a relatively small background with large uncertainty (100%) due to the lack of antiproton production cross section information for the Mu2e proton beam energy of 8 GeV. We have developed a novel methodology to estimate the antiproton background in-situ. This forms the main theme of the thesis. We observed that at Mu2e energies, antiproton annihilation in the stopping target is the only source of events with multiple, simultaneous particle trajectories. From Geant4 simulations, only about 0.2% of the simulated antiproton annihilation events have a signal-like electron. Meanwhile, ∼ 5% of events have multiple reconstructible particle tracks per event. Therefore, we have devised a methodology to reconstruct the multi-track events and estimate the antiproton background by exploiting the large ratio of the production rates of the two final states.

Chithirasreemadam, Namitha [Pisa U.] (ORCID:000000↗
DOE OSTI2024

Exotic particles at the DUNE near detector from charged pion scattering

Fixed-target proton-beam experiments produce a multitude of charged pions that rescatter in the beam dump. These charged pion scattering events can be an additional irreducible source of exotic particles which couple to photons or hadrons. We analyze the sensitivity of the DUNE near detector complex to millicharged particles (MCPs) and heavy axionlike particles (ALPs) with low-energy couplings to gluons. Using the framework of chiral perturbation theory, we demonstrate regimes of parameter space where the charged pion production channel dominates over previously considered production mechanisms for both MCPs and ALPs, thereby improving the sensitivity of DUNE to these new particles compared to previous studies. Published by the American Physical Society 2024

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Global polarization of hyperons and spin alignment of vector mesons in quark matters

Relativistic heavy ion collider (RHIC) as a dedicated nuclear facility has made a few major discoveries in physics. This year marks the 30th year STAR Collaboration formation and the 23th year of STAR detector operation and data collection at RHIC. In the last two decades, STAR has collected many datasets, exhibiting scientific versatility and flexibility of the RHIC facility. The total dataset in the first year is less than 1 million good events, and currently there are about 1 billion events per dataset. The Global Hyperon Polarization was proposed in 2004. This immediately prompted the STAR Collaboration to search for this phenomenon from the early datasets. The null results were presented at Quark Matter Conference in Shanghai in 2006 and subsequently published. Although there were peripheral and continuous efforts in the following decade, no positive result has been observed experimentally. This situation changed in the following decade with the upgrade of high data rate and time-of-flight (TOF) detector and the progress of the Beam Energy Scan Phase I (BES-I). The experimental discoveries of the global polarization of hyperons in 2017 and the spin alignment of vector mesons in 2023 at RHIC-STAR confirm the theory which was established nearly twenty years ago. The theory and these measurements open the way to studying the properties of the hot and dense nuclear matter created in high-energy heavy ion collisions from a new degree of freedom, spin. We briefly review these discoveries from the proposals of theory to the experimental measurements, and summarize the related measurements at the existing facilities and the theoretical explanations to the original proposal. The basic understanding and the original proposal are still valid and fundamental, that is, the angular momentum of system can transform into a spin effect observable in experiment. However, it appears that in each case a new model is needed to explain the new experimental observation. We need a more basic theory to help us unify all these spin related phenomena. Over the past five years, STAR has successfully installed 3 new detectors and we have begun to see the physical analysis results from datasets with those new functions. What makes the STAR detector viable after 20 years of operation is its continuous evolution through successful upgrades, with new scientific programs added year by year. The next big thing is to forward upgrade a tracking system (3 layers of silicon strips and 4 layers of sTGC chambers) and a calorimetry system (electromagnetic and hadronic calorimeters). In addition to studying the spin structure of protons by using the polarized proton beams at RHIC, the upgrades also provide a unique ability to investigate the origin of Λ Global Polarization as a function of rapidity and rapidity (de-)correlations in Au+Au collisions.

Physics↗
NASA NTRS2003

Quantification of rat retinal growth and vascular population changes after single and split doses of proton irradiation: translational study using stereology methods

This study quantified architectural and population changes in the rat retinal vasculature after proton irradiation using stereology. A 100 MeV conformal proton beam delivered 8, 14, 20 and 28 Gy as single and split doses to the whole eye. The vascular networks were prepared from retinal digests. Stereological methods were used to obtain the area of the retina and unbiased estimates of microvessel/artery/vein endothelial, pericyte and smooth muscle population, and vessel length. The retinal area increased progressively in the unirradiated, age-matched controls and in the retinas irradiated with 8 and 14 Gy, indicating uniform progressive retinal growth. No growth occurred after 20 and 28 Gy. Regression analysis of total endothelial cell number in all vessels (arteries, veins and capillaries) after irradiation documented a progressive time- and dose-dependent cell loss occurring over 15 to 24 months. The difference from controls was significant (P<0.01) after 28 Gy given in single and split doses and after 20 Gy given as a split dose (P<0.05). Total vessel length in microvessel was significantly shortened at 20 and 28 Gy compared to that of controls (P<0.05). No evident dose recovery was observed in the endothelial populations after split doses. At 10 Gy, the rate of endothelial cell loss, a dose parameter used to characterize the time- and dose-dependent loss of the endothelial population, was doubled.

NASA Discipline Radiation Health↗
DOE OSTI2025

Improving Longitudinal Impedance of Inductive Inserts

In this article, we discuss methods for improving the longitudinal impedance of inductive inserts used for space charge compensation in the proton storage ring (PSR) at Los Alamos Neutron Science Center (LANSCE) Facility. The PSR relies on inductive inserts to counteract the capacitive impedance produced by the space charge of the proton beam, which can otherwise lead to beam debunching. Existing inductive inserts, which utilize Toshiba M4C21A ferrite, have been effective but require heating to reduce resistive components that can cause instabilities at higher frequencies. This article explores the potential of alternative ferrite materials, specifically National Magnetics C2050, to enhance the performance of these inserts by reducing the need for heating and minimizing resistive impedance. Through both analytical modeling and CST Particle Studio simulations, it is demonstrated that optimized ferrite materials and geometries can significantly improve space charge compensation while mitigating instability risks, ultimately enhancing the performance of the PSR.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Trigger Detection for the sPHENIX Experiment via Bipartite Graph Networks with Set Transformer

Trigger (interesting events) detection is crucial to high-energy and nuclear physics experiments because it improves data acquisition efficiency. It also plays a vital role in facilitating the downstream offline data analysis process. The sPHENIX detector, located at the Relativistic Heavy Ion Collider in Brookhaven National Laboratory, is one of the largest nuclear physics experiments on a world scale and is optimized to detect physics processes involving charm and beauty quarks. Furthermore, these particles are produced in collisions involving two proton beams, two gold nuclei beams, or a combination of the two and give critical insights into the formation of the early universe. This paper presents a model architecture for trigger detection with geometric information from two fast silicon detectors. Transverse momentum is introduced as an intermediate feature from physics heuristics. We also prove its importance through our training experiments. Each event consists of tracks and can be viewed as a graph. A bipartite graph neural network is integrated with the attention mechanism to design a binary classification model. Compared with the state-of-the-art algorithm for trigger detection, our model is parsimonious and increases the accuracy and the AUC score by more than 15%.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Axion-like particle searches at DarkQuest

Axion-like particles (ALPs) interacting with the Standard Model can be abundantly produced in proton beam fixed-target experiments. Looking for their displaced decays is therefore an effective search strategy for ALPs with a mass in the MeV to GeV range. Focusing on the benchmark models where the ALP interacts dominantly with photons or gluons, we show that the proposed DarkQuest experiment at Fermilab will be able to test parameter space which has been previously inaccessible. We pay particular attention to the self-consistency of gluon-coupled ALP production and decay calculations, which has been recently shown to be a problem in many existing predictions. We also apply these results to explore existing constraints in the ALP parameter space.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Probing transverse momentum dependent structures with azimuthal dependence of energy correlators

We study the azimuthal angle dependence of the energy-energy correlators $\langle \mathcal{E}\left({\widehat{n}}_{1}\right)\mathcal{E}\left({\widehat{n}}_{2}\right)\rangle $ in the back-to-back region for e + e - annihilation and deep inelastic scattering (DIS) processes with general polarization of the proton beam. We demonstrate that the polarization information of the beam and the underlying partons from the hard scattering is propagated into the azimuthal angle dependence of the energy-energy correlators. In the process, we define the Collins-type EEC jet functions and introduce a new EEC observable using the lab-frame angles in the DIS process. Furthermore, we extend our formalism to explore the two-point energy correlation between hadrons with different quantum numbers ${\mathbb{S}}_{i}$ in the back-to-back limit $\langle {\mathcal{E}}_{{\mathbb{S}}_{1}}\left({\widehat{n}}_{1}\right){\mathcal{E}}_{{\mathbb{S}}_{2}}\left({\widehat{n}}_{2}\right)\rangle $. We find that in the Operator Product Expansion (OPE) region the nonperturbative information is entirely encapsulated by a single number. Using our formalism, we present several phenomenological studies that showcase how energy correlators can be used to probe transverse momentum dependent structures.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

A light scalar explanation of (g - 2) μ and the KOTO anomaly

The KOTO experiment has recently performed a search for neutral Kaons decaying into neutral pions and a pair of neutrinos. Three events were observed in the KOTO signal region, with an expected background of about 0.05. Since no clear signal of systematic errors have been found, the excess of events in the decay K-L → π 0 v$\overline{v}$ is quite intriguing. One possibility to explain this anomaly would be the presence of a scalar $\phi$ with mass of the order of the pion mass and inducing decays K-L → π 0 $\phi$ which mimic the observed signal. A scalar with mass of the order of the pion mass and a coupling to muons of the order of the Standard Model Higgs coupling could also explain the muon anomalous magnetic moment anomaly (g - 2) μ . We built on these facts to show that a light singlet scalar with couplings to the leptons and quarks as the ones induced by mixing with Higgs states in two Higgs doublet models may lead to an explanation of both anomalies. More specifically, we show that this is the case in the so-called type-X models in which leptons and quarks couple to two different Higgs doublets, and for scalar masses that are in the range between 40 and 70 MeV. Due to the relatively large coupling to leptons required to fit (g - 2) μ , the scalar lifetime accidentally falls into the sub-nanosecond range which is essential to evade the severe proton beam dump experiments and astrophysical constraints, though it becomes sensitive to constraints from electron beam dump experiments. The additional phenomenological properties of this model are discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

48 Ca(p,pn) 47 Ca linac production for the preparation of a 47 Ca/ 47 Sc generator

Here, the production of 47 Sc via the nuclear reaction 48 Ca(p,pn) 47 Ca→(β-, T 1/2 = 4.54 d) 47 Sc and the assembly of a 47 Ca/ 47 Sc generator system has been investigated at Brookhaven National Laboratory. To produce 47 Ca, a pressed nat CaCl 2 target was irradiated with a proton beam at energy on target of 27.5 MeV at Brookhaven Linac Isotope Producer. Irradiated targets were dissolved in water and then acidified with concentrated HCl before separation using extraction chromatography through a diglycolamide (DGA) resin column. After ingrowth, 47 Sc was collected at >90 % with low contamination from both nonradioactive metals and coproduced radionuclides. A total of four 47 Ca/ 47 Sc separations were performed with 6–7 days between the irradiation and the separation to allow the equilibration of the ingrowing 47 Sc.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Experimental capabilities of the LMJ-PETAL facility

In this study, recent progress in the experimental capabilities of the LMJ-PETAL laser facility is reviewed. Updates on the indirect-drive D 2 implosion experiments and equation-of-state experiments using the LMJ laser are presented, including the commissioning of new plasma diagnostics. Several recent campaigns using the PETAL laser alone are also presented, namely the development of a platform using high-resolution and high-energy X-ray sources for radiography experiments, laser wakefield acceleration studies in the self-modulated regime, and neutron generation using a Target Normal Sheath Accelerated proton beam in a pitcher-catcher configuration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗