Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Effects of TiCl4 Purity on the Sinterability of Armstrong-Processed Ti Powder

A series of high purity and low purity powders were synthesized from TiCl4 by the Armstrong process. While both powders displayed swelling when consolidated and sintered, the lower purity powder exhibited this phenomenon in significantly lower degree. The improvement is attributed to the increase in the onset of sintering temperature, which mitigates the entrapment of volatile impurities that would otherwise lead to pore formation and growth. The net effect is that the use of a lower purity TiCl4 may beneficial in two ways: (1) it is a potentially lower cost precursor to Ti powder production and (2) the trace impurities allow higher density components to be fabricated via a typical low-cost press and sinter approach.

36 MATERIALS SCIENCE↗

Mechanically strengthened heterogeneous Sm-Co sintered magnets

Samarium-cobalt sintered magnets offer excellent magnetic properties, thermal stability, and corrosion resistance. They are used in a variety of defense and civilian applications, especially when elevated operation temperatures (e.g., 200 ºC to 550 ºC) are required. However, the utilization of these materials is restricted by their brittleness. Improving their mechanical resilience would make them more cost-effective, efficient, and robust in decarbonization and other function-related applications while reducing the pressure on critical material supply chains. In this paper, we engineer a series of novel heterogeneous microstructures, such as laminated coarse grain (CG)/fine grain (FG) and core/shell CG/FG microstructures, to produce unprecedented combinations of superior mechanical and magnetic properties without altering the chemical compositions of the magnets or common heat treatment procedures. Further, a 60% flexural strength enhancement is obtained using heterogeneous Sm 2 (CoFeCuZr) 17 sintered magnets with little impact on their magnetic properties. The mechanically robust heterogeneous Sm-Co sintered magnets have a minor (e.g., less than 4.6%) reduction in the energy product (BH) max due to a slightly reduced squareness of the demagnetization curve, with no decrease in either the remanence (B r ) or the intrinsic coercivity (H ci ). The flexural strengths of these heterogeneous Sm-Co magnets depend on the volume ratios and mean grain sizes of the FG/CG regions, as well as their microstructural architectures. The fine-grained regions act as mechanical strengthening sites, which can be strategically used when designing the magnet for different applications. This technology is highly compatible with existing magnet manufacturing processes and thus can be adopted readily by the magnet industry.

36 MATERIALS SCIENCE↗

Mechanically robust high magnetic-performance Sm-Co sintered magnets through microstructure engineering

Samarium-cobalt (Sm-Co) sintered magnets have high magnetic energy densities, great resistance to demagnetization and corrosion, and excellent thermal stability in a wide temperature range (–50–550 °C). However, the utilization of these magnets is restricted by their brittleness. Based on micromechanical and the Zener pinning model, Sm-Co sintered magnets with improved mechanical properties have been designed and fabricated via microstructure engineering. A small amount of fine Sm 2 O 3 particulates (0–3 wt%) has been incorporated into Sm 2 (CoFeCuZr) 17 sintered magnets to refine the grain size by up to approximately 50% (from 45 to 22 µm) and narrow the grain size distribution. Doping with 3 wt% Sm 2 O 3 increased the flexural strength by 62% while maintaining magnetic performance. Both grain-refined unimodal microstructure and heterogeneous laminated coarse/fine grain microstructure were formed by strategically designed assemblies of Sm 2 O 3 -added Sm-Co powder feedstock mixtures. The technology is compatible with existing magnet manufacturing processes. Numerical micromechanics simulation indicates that the fracture is dominated by intragranular mode. The mechanical strength is mainly enhanced by the additive-induced grain refinement, while the small amount of Sm 2 O 3 addition has a small direct positive contribution. Finally, these magnets will be more cost-effective, efficient, and robust for various functional applications.

36 MATERIALS SCIENCE↗

Densification of non-radioactive porous siliceous particles loaded with cesium potassium copper hexacyanoferrate by spark plasma sintering

In the development of a conditioning process for cesium-bearing sorbents from the decontamination of aqueous waste streams, the treatment of a granular material composed of (Cs,K) 2 CuFe(CN) 6 loaded onto mesoporous silica particles has been investigated in an additive-free two-step conditioning process involving (i) calcination at 1000 °C to remove volatile species and (ii) densification by spark plasma sintering. A 92.0 % dense pellet was obtained after 10 min sintering at 850 °C under 100 MPa. Density and microstructural measurements indicate that densification is first driven by the viscous flow of a vitreous phase containing Cs, formed during calcination. Additionally, the density of the sample then increases further during sintering by grain boundary diffusion. However, a limited but non negligible part of cesium is lost during densification.

36 MATERIALS SCIENCE↗

Synthesis, sintering, and grain growth kinetics of Hf 6 Ta 2 O 17

Here Aasystematic study of the solid-state synthesis, pressureless sintering, and grain growth kinetics of Hf 6 Ta 2 O 17 is presented. The ideal conditions for solids-state synthesis of Hf 6 Ta 2 O 17 powder with minimal particle necking was 1250 °C for 2 h in air. The resultant powder has an average particle size of 210 ± 70 nm. The combined synthesis and ball-milling procedure produces highly sinterable Hf 6 Ta 2 O 17 powder, achieving > 97 % of theoretical density after pressureless sintering at 1600 °C for 2 h in air. The grain growth mechanism was sensitive to processing conditions, appearing to be primarily driven by surface diffusion below 1600 °C and grain boundary diffusion above 1650 °C. The respective activation energies for grain growth were found to be Q S = 659 ± 79 kJ mol -1 and Q GB = 478 ± 63 kJ mol -1 .

36 MATERIALS SCIENCE↗

Internal defect detection and characterization of samarium-cobalt sintered magnets by ultrasonic testing technique

Excessive quantities of samarium-cobalt (Sm-Co) magnet material are being scrapped needlessly due to a lack of understanding of inhomogeneity distribution and unacceptable internal defects. If there is a way to identify, locate, characterize and when needed separate the defective portions of magnet material, utilization can be increased and product quality improved. Further, the magnets’ magnetic and mechanical performance can be improved by reducing the occurrence of internal defects. This paper reports on a cost-effective and efficient nondestructive evaluation method based on an ultrasonic testing (UT) technique applied for detecting and characterizing internal defects in Sm-Co sintered magnets. Applying the UT technique will allow users to comprehensively analyze internal defects, such as inclusions, porosity, microcracks, and other structural irregularities, check for homogeneity and anomalous regions and give the locations of these internal anomalies and defects within the Sm-Co sintered magnets. The UT technique can also be applied to other rare-earth permanent magnets, such as sintered or die-upset neodymium-iron-boron (Nd-Fe-B) magnets. The UT technique can effectively guide quality control and acceptable product selection, in addition to optimizing the magnet alloy design and production processes. Therefore, it can facilitate the improvement of magnet manufacturing efficiency and machinability, reduce scrap, prolong service life, increase the use of what would be post-production waste, and enhance product reuse and recycling at end-of-life disposition.

36 MATERIALS SCIENCE↗

Al{sub 2}O{sub 3} - TiO{sub 2}-A simple sol-gel strategy to the synthesis of low temperature sintered alumina-aluminium titanate composites through a core-shell approach

A simple sol-gel based core-shell approach for the synthesis of alumina-aluminium titanate composite is reported. Alumina is the core and titania is the shell. The coating of titania has been performed in aqueous medium on alumina particle by means of heterocoagulation of titanyl chloride. Further heat treatment results in low temperature formation of aluminium titanate as well as low temperature sintering of alumina-aluminium titanate composites. The lowering of the reaction temperature can be attributed to the maximisation of the contact surface between the reactants due to the core-shell approach involving nanoparticles. The mechanism of formation of aluminium titanate and the observations on densification features in the present process are compared with that of mixture of oxides under identical conditions. The sintered alumina-aluminium titanate composite has an average grain size of 2 {mu}m. - Graphical abstract: The article presents a simple sol-gel process through core-shell approach to the synthesis of low temperature sintered alumina-aluminium titanate. The lowering of the reaction temperature can be attributed to the maximisation of the contact surface between the reactant due to the core-shell approach. This material showed the better microstructure control compared to the standard solid-state mixing route.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Uncontrollable expansion of PbZn{sub 1/3}Nb{sub 2/3}O{sub 3}-PbTiO{sub 3} perovskite{yields}pyrochlore transition during spark plasma sintering: Mechanism proposal using infinite periodic minimal surfaces

The PbZn{sub 1/3}Nb{sub 2/3}O{sub 3}-PbTiO{sub 3} phase (PZN-PT) prepared by mechanosynthesis exhibits interesting relaxor properties when transformed into nanostructured ceramic by spark plasma sintering. When trying to obtain denser ceramic to enhance physical properties, the PZN-PT phase transformation from perovskite to pyrochlore structure induces the graphite die explosion. An explanation of this phenomenon is based on the reorganization of the lone pairs corresponding to Pb{sup 2+} cations into the large cavities of pyrochlore network, inducing an important cell volume increase, together with the speed of transformation depicted in the light of infinite periodic minimal surfaces describing the perovskite (P-surface) and the pyrochlore (F-surface) networks, respectively. - Graphical abstract: The explosive phenomenon observed during the sintering of PZN-PT phase using spark plasma sintering is directly linked to the perovskite{yields}pyrochlore phase transition and the volume increase related to the role of the Pb lone pairs. Infinite periodic minimal surfaces have been used to describe the structures and the phase transition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of phosphorus additions on the sintering and transport properties of proton conducting BaZr{sub 0.85}Y{sub 0.15}O{sub 3-{delta}}

The influence of phosphorous additions on the sintering and electrical transport properties of the proton-conducting perovskite BaZr{sub 0.85}Y{sub 0.15}O{sub 3-{delta}} (BZY) has been studied with a view to the use of phosphates as typical dispersants for the formation of stabilised solid suspensions or as possible sintering aids. P{sub 2}O{sub 5} additions, (1-x)BZY{center_dot}xP{sub 2}O{sub 5}, monotonously promote densification in the intermediate compositional range 0.04{<=}x{<=}0.08. Nonetheless, BZY reacts with phosphorous forming the phase Ba{sub 3}(PO{sub 4}){sub 2} at temperatures as low as 600 Degree-Sign C. The associated loss of Ba from the perovskite, leads to a decrease in the perovskite lattice parameter, the formation of yttria-based impurity phases and impaired grain growth. Such reaction has an extremely detrimental effect on bulk and grain boundary conductivities. It is, therefore, vital that the current results are taken into account by the protonics community when attempting to prepare the stabilised solid suspensions of BZY nanopowders required for thin ceramic applications. Alternative dispersants to phosphate esters must be found. - Graphical Abstract: Sintering experiments performed at 1500 Degree-Sign C for 5 h and at 1400 Degree-Sign C for 24 h of (1-x)BaZr{sub 0.85}Y{sub 0.15}O{sub 3-{delta}}{center_dot}xP{sub 2}O{sub 5} in the range x=0-0.10. Highlights: Black-Right-Pointing-Pointer P{sub 2}O{sub 5} additions, (1-x)BZY{center_dot}xP{sub 2}O{sub 5}, promote densification in the intermediate compositional range 0.04{<=}x{<=}0.08. Black-Right-Pointing-Pointer BZY reacts with phosphorous forming the phase Ba{sub 3}(PO{sub 4}){sub 2} at temperatures as low as 600 Degree-Sign C. Black-Right-Pointing-Pointer Detrimental effects on bulk and grain boundary conductivities are shown. Black-Right-Pointing-Pointer Alternative dispersants to phosphate esters must be found.

36 MATERIALS SCIENCE↗

Gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline type-I Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) clathrates prepared by combining arc melting and spark plasma sintering methods

The gallium composition dependence of crystallographic and thermoelectric properties in polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} (nominal x=14-18) compounds with the type-I clathrate structure is presented. Samples were prepared by combining arc melting and spark plasma sintering methods. Powder x-ray diffraction, Rietveld analysis, scanning electron microscopy, and energy-dispersive x-ray spectroscopy show that the solubility limit of gallium in the type-I clathrate phase is close to x=15, which is slightly higher than that for a single crystal. The carrier concentration at room temperature decreases from 2 Multiplication-Sign 10{sup 21} cm{sup -3} to 4 Multiplication-Sign 10{sup 20} cm{sup -3} as the Ga content x increases. The Seebeck coefficient, the electrical conductivity, and the thermal conductivity vary systematically with the carrier concentration when the Ga content x varies. The effective mass (2.0m{sub 0}), the carrier mobility (10 cm{sup 2} V{sup -1} s{sup -1}), and the lattice thermal conductivity (1.1 W m{sup -1} K{sup -1}) are determined for the Ga content x=14.51. The dimensionless thermoelectric figure of merit ZT is about 0.55 at 900 K for the Ga content x=14.51. The calculation of ZT using the experimentally determined material parameters predicts ZT=0.8 (900 K) at the optimum carrier concentration of about 2 Multiplication-Sign 10{sup 20} cm{sup -3}. - Graphical abstract: The gallium composition dependence of crystallographic and thermoelectric properties is presented on polycrystalline n-type Ba{sub 8}Ga{sub x}Si{sub 46-x} with the type-I clathrate structure prepared by combining arc melting and spark plasma sintering methods. The thermoelectric figure of merit ZT reaches 0.55 at 900 K due to the increase in the Ga content (close to x=15), and a calculation predicts further improvement of ZT at the optimized carrier concentration. Highlights: Black-Right-Pointing-Pointer Crystallographic properties of Ba{sub 8}Ga{sub x}Si{sub 46-x} clathrates are characterized. Black-Right-Pointing-Pointer Arc melting and spark plasma sintering process enables increase of Ga content. Black-Right-Pointing-Pointer We elucidate the Ga composition dependence of thermoelectric properties. Black-Right-Pointing-Pointer Thermoelectric figure of merit ZT is improved due to the increased Ga content. Black-Right-Pointing-Pointer Calculation predicts a potential ZT=0.8 at 900 K at optimized carrier concentration.

36 MATERIALS SCIENCE↗

Characterization, sintering and dielectric properties of nanocrystalline barium titanate synthesized through a modified combustion process

Nanocrystalline barium titanate has been synthesized through a modified combustion process in a single step for the first time. The as-prepared barium titanate powder is cubic perovskite with lattice constant a = 4.018 A. The phase purity of the nanopowder was examined using thermo gravimetric analysis, differential thermal analysis and Fourier transform infrared spectroscopy. Transmission electron microscopic investigations have shown that the particle size of the as-prepared powder is in the range 20-40 nm. The agglomerate size distribution of the as-prepared powder was studied using atomic force microscopy. The nanoparticles of barium titanate were sintered to 97% of the theoretical density at a temperature of 1350 deg. C for 3 h. The microstructure of the sintered surface was examined using scanning electron microscopy. The dielectric constant and loss factor of the sintered pellets at 1 MHz measured at room temperature were 1223 and 3.5 x 10{sup -3} respectively.

36 MATERIALS SCIENCE↗

Evaluation of suitable porosity for sintered porous {beta}-tricalcium phosphate as a bone substitute

Structural and mechanical characterization is performed for sintered porous beta tricalcium phosphate ({beta}-TCP) to determine the appropriate porosity for use as a bone substitute. Four different types of porous {beta}-TCP specimen with different porosities are fabricated through a sintering process. For structural characterization, scanning electron microscopy and a Microfocus X-ray computed tomography system are used to investigate the pore openings on the specimen's surface, pore size, pore distribution, and pore interconnections. Compression tests of the specimens are performed, and mechanical properties such as the elastic modulus and compressive strength are obtained. Also, the geometric shape and volume of the {beta}-TCP around the contact region of two pores, which need to be initially resolved after implantation in order to increase the size of the pore openings, are evaluated through simple calculations. The results show that porous {beta}-TCP with 42.1% porosity may be a suitable bone substitute candidate in terms of sustaining external loads, and inducing and cultivating bone cells. - Highlights: Black-Right-Pointing-Pointer Structural and mechanical characterization was performed for sintered porous {beta}-TCP specimens. Black-Right-Pointing-Pointer For structural characterization, SEM and Microfocus X-ray CT system were used. Black-Right-Pointing-Pointer For mechanical characterization, compression tests were performed. Black-Right-Pointing-Pointer Porous {beta}-TCP with 42.1% porosity may be a suitable bone substitute.

36 MATERIALS SCIENCE↗

The effect of Si on the microstructure and mechanical properties of spark plasma sintered boron carbide

Highlights: • Si addition leads to a dense final product at a low sintering temperature. • The added Si preferentially formed SiC and borosilicate glass instead of replacing the chain atoms in boron carbide. • The hardness of our Si-containing boron carbide is 30–35% greater than currently in-use commercial boron carbide plates. - Abstract: Fully dense boron carbide discs were achieved by spark plasma sintering boron carbide powders with 10 wt% silicon. The silicon did not diffuse into boron carbide grains to produce a solid solution of Si-doped boron carbide; instead the silicon reacted with impurities in the starting powder to form β-SiC and borosilicate glass. The resultant new phases facilitated densification of the multiphase ceramic through liquid phase-assisted sintering. The resultant material exhibits improved hardness (34.3 GPa Vikers hardness under 1 kg load) with toughness comparable to both Si-free and commercially available boron carbide.

36 MATERIALS SCIENCE↗

Phase evolution during spark plasma sintering of novel Si3N4-doped TiB2–SiC composite

Highlights: • The effect of Si{sub 3}N{sub 4} addition on microstructure of TiB{sub 2}–SiC composite was studied. • Fully dense TiB{sub 2}-based composite was obtained by addition of SiC and Si{sub 3}N{sub 4}. • TiC, B{sub 4}C and SiO{sub 2} were formed in Si{sub 3}N{sub 4}-free and Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC ceramics. • TiN and BN were in-situ formed only in Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC sample. - Abstract: Spark plasma sintering process was employed to fabricate TiB{sub 2}–SiC and novel Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC ceramic composites at 1900 °C for 7 min under 40 MPa. The microstructural development of TiB{sub 2}-based composites was significantly influenced by the addition of SiC as a reinforcement phase and Si{sub 3}N{sub 4} as a sintering aid. Thermodynamic assessment, X-ray diffractometry, scanning electron microscopy and energy dispersive spectroscopy disclosed the in-situ formation of TiC, B{sub 4}C and SiO{sub 2} in both samples as well as TiN and BN in the Si{sub 3}N{sub 4}-doped TiB{sub 2}–SiC sample through the chemical reactions of SiC and Si{sub 3}N{sub 4} additives with the surface oxide impurities of TiB{sub 2} particles (TiO{sub 2} and B{sub 2}O{sub 3}). The elimination of harmful oxide layers and the in-situ formation various secondary phases had remarkable influences on the sinterability and final microstructure of TiB{sub 2}.

36 MATERIALS SCIENCE↗

From tin oxalate to (Fe, Co, Nb)-doped SnO{sub 2}: Sintering behavior, microstructural and electrical features

Highly reactive SnO{sub 2}-doped nanocrystalline powders with average particle size of 20 nm and specific surface areas above 30 m{sup 2}/g were obtained through the polymeric precursor method with tin oxalate (SnC{sub 2}O{sub 4}) as a chloride-free precursor for SnO{sub 2}. Powders and sintered discs were characterized by means of X-ray powder diffraction (XRD), SEM and TEM. The influence of Co and Fe on the microstructure development and on the electrical properties of dense SnO{sub 2}-based ceramics was studied. Co and Fe species were found to decrease in more than 70 deg. C the sintering temperature of SnO{sub 2} with respect to mixed oxide procedures. Secondary phases enriched in Co and Fe were detected and identified in sintered samples with XRD. Current-voltage curves were registered for electrical characterization. Doping with iron increased the electrical breakdown field and a nonlinearity coefficient of 20 was achieved.

36 MATERIALS SCIENCE↗

Sintering, microstructure and microwave dielectric properties of rare earth orthophosphates, RePO{sub 4} (Re = La, Ce, Nd, Sm, Tb, Dy, Y, Yb)

Various rare earth orthophosphates, such as monazite and xenotime RePO{sub 4} (Re = La, Ce, Nd, Sm, Tb, Dy, Y, Yb) were prepared by a conventional solid-state reaction method. The crystal structure and microstructure of the sintered ceramics were investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM), respectively. The dielectric properties were measured in the microwave region using a network analyzer. It was found that the monazite RePO{sub 4} could be sintered near 1400 deg. C, although the xenotime RePO{sub 4}, which had a smaller Re{sup 3+} ionic radius, could be sintered above 1600 deg. C. The permittivity ({epsilon}{sub r}) of the monazite structures was higher than that of the xenotime structures. This difference was explained by the differences in ionic polarizability and bond strength. Both monazite and xenotime rare earth orthophosphates, however, exhibited a high quality factor (Q x f), where Q = 1/tan {delta} and f is the measuring frequency, of greater than 60,000 GHz. The temperature coefficient of resonant frequency ({tau}{sub f}) was a negative value, ranging between -17 and -56 ppm/deg. C.

36 MATERIALS SCIENCE↗

Si-substituted hydroxyapatite nanopowders: Synthesis, thermal stability and sinterability

Synthetic hydroxyapatites incorporating small amounts of Si have shown improved biological performances in terms of enhanced bone apposition, bone in-growth and cell-mediated degradation. This paper reports a systematic investigation on Si-substituted hydroxyapatite (Si 1.40 wt%) nanopowders produced following two different conventional wet methodologies: (a) precipitation of Ca(NO{sub 3}){sub 2}.4H{sub 2}O and (b) titration of Ca(OH){sub 2}. The influence of the synthesis process on composition, thermal behaviour and sinterability of the resulting nanopowders is studied. Samples were characterised by electron microscopy, induced coupled plasma atomic emission spectroscopy, thermal analysis, infrared spectroscopy, N{sub 2} adsorption measurements, X-ray diffraction and dilatometry. Semicrystalline Si-substituted hydroxyapatite powders made up of needle-like nanoparticles were obtained, the specific surface area ranged between 84 and 110 m{sup 2}/g. Pure and Si-substituted hydroxyapatite nanopowders derived from Ca(NO{sub 3}){sub 2}.4H{sub 2}O decomposed around 1000 deg. C. Si-substituted hydroxyapatite nanopowders obtained from Ca(OH){sub 2} were thermally stable up to 1200 deg. C and showed a distinct decreased thermal stability with respect to the homologous pure sample. Si-substituted hydroxyapatites exhibited higher sintering temperature and increased total shrinkage with respect to pure powders. Nanostructured dense ceramics were obtained by sintering at 1100 deg. C Si-substituted hydroxyapatites derived from Ca(OH){sub 2}.

36 MATERIALS SCIENCE↗

Sintering kinetic studies in nonstoichiometric strontium titanate ceramics

The effect of nonstoichiometry on the densification of SrTiO{sub 3} ceramics with Sr/Ti ratios from 0.997 to 1.02 was systematically addressed. The kinetics of densification was studied by dilatometric analysis. X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used for crystallographic and microstructure characterization. Ti excess enhanced matter transport during sintering whereas Sr excess decreased it. The shrinkage rate and average grain size increased with the decrease of Sr/Ti ratio. Close values of the activation energy for the initial densification and the near constant onset temperature for densification suggest that identical transport mechanisms control the densification of all the compositions. Small excesses of TiO{sub 2} and SrO were mostly incorporated into the perovskite lattice inducing alterations in the defect chemistry of the material and the mass transport during sintering is controlled by Sr vacancies. Very small stoichiometric variations have a strong influence on the sintering kinetics and resulting microstructure of ST ceramics.

36 MATERIALS SCIENCE↗