Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface emissivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

High-efficiency solar thermophotovoltaic system using a nanostructure-based selective emitter

Herein, we present the design, fabrication, optimization, and experimental results of a high-efficiency planar solar thermophotovoltaic (STPV) system utilizing a micro-textured absorber and a nanostructure multilayer metal-dielectric coated selective emitter fabricated on a tungsten (W) substrate. Light absorptance of more than 90% was achieved at visible and near-infrared wavelengths using the microtextured absorbing surface. The nanostructure selective emitter consists of two thin-film optical coatings of silicon nitride (Si3N4) and a layer of W in between to increase the surface emissivity in spectral regimes matching the quantum efficiency of the thermophotovoltaic (TPV) cells. Gallium antimonide (GaSb)-based TPV cells are used in our STPV design. The experiment was conducted at different operating temperatures using a high-power continuous wave laser diode stack as a simulated source of concentrated incident radiation. Our experimental setup measured a maximum electrical output power density of 1.71 W/cm 2 at 1676 K STPV temperature, and the overall power conversion efficiency of 8.4% after normalizing the output power density to the emitter area. This is the highest STPV system efficiency reported so far for any experimental STPV device. The incident optical laser power on the absorber side was 131 W. This is equivalent to a solar concentration factor of ~2100, which is within the practical limit and readily achievable with Fresnel lens setup.

14 SOLAR ENERGY↗

Aerosol Vertical Turbulent Mass Flux Retrievals Through Novel Remote Sensing Algorithm

Abstract Integrated measurements of aerosol, radiation, cloud, and turbulent transport in the planetary boundary layer (PBL) are essential for understanding and modeling climate and air quality. Here, we developed a new technique for the identification of convective turbulent regions and deriving the vertical distribution of aerosol turbulent mass fluxes within PBL. The algorithm uses retrievals from coherent Doppler lidars and a high spectral resolution lidar. The technique was applied to study particle mass fluxes over 2 months (November–December 2020) during the campaign conducted at the DOE Atmospheric Radiation Measurement Southern Great Plains (SGP) site in Lamont, Oklahoma. The algorithm developed here is capable of continuously deriving vertically resolved (curtains) aerosol mass fluxes. Our data analysis shows that at the site, the 30‐min averaged fluxes at 135 m above the surface were mainly positive (upward) at ∼1 μg m −2 s −1 , suggesting that the surface is the primary source of the particle mass supplied to the boundary layer at the SGP site. Analyses of the individual case studies have revealed that not all the derived fluxes can be linked to surface emissions. Both positive and negative values in a range of ±5 μg m −2 s −1 can be caused by convective thermals interacting between the residual layer and the mixed layer and by rotation of the horizontal wind with the height. Large erroneous negative fluxes can also be caused by drizzling/precipitating clouds. We anticipate that the application of the current technique will lead to a more realistic representation of aerosol mass budgets and bidirectional mixing rates.

54 ENVIRONMENTAL SCIENCES↗

Spring Dust in Colorado Plateau: Transport Pathways and Interannual Variability Derived From Two Decades of MERRA‐2 Reanalysis

Spring dust storms in the U.S. Southwest significantly impact environmental and human systems, yet their climatological patterns and driving mechanisms remain poorly understood. Using two decades of MERRA-2 reanalysis data and self-organizing map clustering, we identified four distinct dust transport pathways from surrounding and remote deserts for the top 10% of spring dust events impacting the Colorado Plateau: (a) intense southwesterly near-surface transport where eastward upward transport is blocked by topography, (b) substantial remote transport plus weaker surface emissions, (c) moderate southwesterly transport with stronger upper-level transport, and (d) rare northwesterly pattern linked to the Great Basin sources, which accounts for 38%, 14%, 37%, and 11% of total events, respectively. The frequency and intensity of these events strongly correlate with large-scale climate variability, with increased dust events during La Niña. Our results provide a robust framework for improving seasonal dust forecasts and understanding future dust dynamics under climate change.

aerosol transport↗

Chemical imaging of individual stratospheric particles sampled over North America

The increasing size, severity, and frequency of wildfires have led to dramatic increases in particulate matter concentrations in the troposphere. Severe wildfires can generate intense convective systems capable of transporting large quantities of biomass burning organic aerosols (BBOA) to the upper troposphere and lower stratosphere (UTLS). Chemically complex organic matter and light-absorbing carbonaceous material is introduced into stratospheric regions that were historically isolated from direct surface emissions. In this study, stratospheric particles were sampled over North America during the Dynamics and Chemistry of the Summer Stratosphere (DCOTSS) campaign, an aircraft-based research project designed to characterize convective perturbation in the UTLS. Particle samples collected from six research flights during summer 2022 were analyzed using Computer-Controlled Scanning Electron Microscopy and Scanning Transmission X-ray Microscopy to investigate particle size distributions, morphology, chemical composition, and mixing state of stratospheric particles along transects across the continental United States and adjacent Pacific Ocean airspace. Analysis revealed that all sampled particles contained detectable levels of carbon, with most exhibiting organic volume fractions of 0.37 ± 0.20. Notably, about 5% of the particles also contained soot inclusions, which indicates the presence of refractory black carbon transported to stratospheric altitudes and provides direct evidence of wildfire-derived black carbon reaching the UTLS. Typical particle morphology exhibits organic shells over soot and inorganic cores and suggests secondary processing and aging of BBOA during transport to and within the UTLS. These findings provide compelling evidence that wildfire emissions play a critical role in affecting the long-term composition and radiative properties of stratospheric particles.

Sharpe, Steven [Purdue Univ., West Lafayette, IN (↗

Gamma-jet tomography of high-energy nuclear collisions in NLO pQCD

Within the NLO pQCD partem model study, suppression of away-side hadron spectra associated with a high p{sub T} photon due to parton energy loss is shown to provide more complete tomographic picture of the dense matter formed in high-energy heavy-ion collisions. Hadron spectra at large Z{sub T} P{sub T}{sup h}/p{sub T}{sup {lambda}} > or approx. 1 are more susceptible to parton energy loss and therefore are dominated by surface emission of {lambda}-correlated jets, whereas small Z{sub T} hadrons mainly come from fragmentation of jets with reduced energy which is controlled by the volume emission. These lead to different centrality dependence of the hadron suppression in different region of Z{sub T}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Calibration of a thin metal foil for infrared imaging video bolometer to estimate the spatial variation of thermal diffusivity using a photo-thermal technique

A thin metal foil is used as a broad band radiation absorber for the InfraRed imaging Video Bolometer (IRVB), which is a vital diagnostic for studying three-dimensional radiation structures from high temperature plasmas in the Large Helical Device. The two-dimensional (2D) heat diffusion equation of the foil needs to be solved numerically to estimate the radiation falling on the foil through a pinhole geometry. The thermal, physical, and optical properties of the metal foil are among the inputs to the code besides the spatiotemporal variation of temperature, for reliable estimation of the exhaust power from the plasma illuminating the foil. The foil being very thin and of considerable size, non-uniformities in these properties need to be determined by suitable calibration procedures. The graphite spray used for increasing the surface emissivity also contributes to a change in the thermal properties. This paper discusses the application of the thermographic technique for determining the spatial variation of the effective in-plane thermal diffusivity of the thin metal foil and graphite composite. The paper also discusses the advantages of this technique in the light of limitations and drawbacks presented by other calibration techniques being practiced currently. The technique is initially applied to a material of known thickness and thermal properties for validation and finally to thin foils of gold and platinum both with two different thicknesses. It is observed that the effect of the graphite layer on the estimation of the thermal diffusivity becomes more pronounced for thinner foils and the measured values are approximately 2.5–3 times lower than the literature values. It is also observed that the percentage reduction in thermal diffusivity due to the coating is lower for high thermal diffusivity materials such as gold. This fact may also explain, albeit partially, the higher sensitivity of the platinum foil as compared to gold.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optically pumped lasing in single crystals of organometal halide perovskites prepared by cast-capping method

A simple “cast-capping” method is adopted to prepare single-crystal perovskites of methyl ammonium lead bromide (CH{sub 3}NH{sub 3}PbBr{sub 3}). By capping a CH{sub 3}NH{sub 3}PbBr{sub 3} solution casted on one substrate with another substrate such as glass, mica, and distributed Bragg reflector (DBR), the slow evaporation of solvent enables large-size cubic crystals to grow between the two substrates. Under optical pumping, edge-emitting lasing is observed based on Fabry–Pérot resonation between parallel side facets of a strip-shaped crystal typically with a lateral cavity length of a few tens of μm. On the other hand, vertical-cavity surface-emitting lasing (VCSEL) is obtained from a planar crystal grown between two DBRs with a cavity thickness of a few μm. Simultaneous detection of those edge- and surface-emissions reveals that the threshold excitation fluence of VCSEL is higher than that of the edge-emitting lasing due to thickness gradient in the planar crystal.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Preliminary measurements of the edge magnetic field pitch from 2-D Doppler backscattering in MAST and NSTX-U (invited)

The Synthetic Aperture Microwave Imaging (SAMI) system is a novel diagnostic consisting of an array of 8 independently phased antennas. At any one time, SAMI operates at one of the 16 frequencies in the range 10-34.5 GHz. The imaging beam is steered in software post-shot to create a picture of the entire emission surface. In SAMI’s active probing mode of operation, the plasma edge is illuminated with a monochromatic source and SAMI reconstructs an image of the Doppler back-scattered (DBS) signal. By assuming that density fluctuations are extended along magnetic field lines, and knowing that the strongest back-scattered signals are directed perpendicular to the density fluctuations, SAMI’s 2-D DBS imaging capability can be used to measure the pitch of the edge magnetic field. In this paper, we present preliminary pitch angle measurements obtained by SAMI on the Mega Amp Spherical Tokamak (MAST) at Culham Centre for Fusion Energy and on the National Spherical Torus Experiment Upgrade at Princeton Plasma Physics Laboratory. Lastly, the results demonstrate encouraging agreement between SAMI and other independent measurements.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Superlinearity, saturation, and the PMT—Tailoring and calibration methodology for prompt radiation detectors

This work illustrates predominant measureable nonlinearities in photomultiplier tubes (PMTs) and introduces a controllable one called “Superlinearity,” signifying both a positive nonlinear response and the ability to extend linear operation by counteracting gain saturation mechanisms — charge depletion, space-charge field limitation, and secondary emission surface effects. Recognizing superlinearity and its effect on the temporal step response leads to a true definition of linearity, free of a small-signal linear assumption. Furthermore, given the prevalent use of glass microchannel-plate (MCP) PMTs in favor of a faster impulse response in spite of a small charge limit, we are motivated to examine their nonlinear amplitude response and deploy tailored gain bias string methods to fully harness the maximum linear gain as is usually done for transmissive metal mesh and reflective metal dynode PMTs. Our characterization methodology applies standard NIST-traceable calibrated laboratory equipment with absolute input-referenced techniques, examining step responses over many orders of magnitude in controlled illumination. By doing so, we quantitatively reveal the superlinearity strength independent of charge depletion, yielding true linear responsivity and effectively doubling the small-signal linear limit; this is very relevant to PMT modeling and charge deconvolution efforts. In conclusion, with further development, the tailoring strategies we introduce could be applied to MCP detectors, extracting all useful capillary charge with a significant improvement in large linear signal quality.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modulation of recombination zone position for white perovskite/organic emitter hybrid light-emitting devices

We report metal halide perovskites present specific challenges as emitters in large area, surface emission lighting devices. Among these challenges is the vast difference in carrier mobilities between the perovskite and many organic buffer layers typically used in such device fabrication as transport and blocking layers. This can make it difficult to engineer recombination to achieve white emitting devices generally. However, in this work, we introduce unique modulation of excitonic confinement within the perovskite layer of the device stack to control overall placement of the recombination zone. This results in a white light emitter that is bright and highly tunable, providing a path to realize white perovskite related light-emitting devices.

42 ENGINEERING↗

Scattered-light uniformity imager for diagnosing laser absorption asymmetries on OMEGA

Light scattered from a target is the most-direct measurement for diagnosing laser absorption in a direct-drive implosion. Observations from OMEGA implosions show much larger scattered-light asymmetries than predictions. A new instrument has been developed to absolutely measure the scattered-light intensity and nonuniformity for the purpose of diagnosing the asymmetry. The scattered-light uniformity imager (SLUI) diagnostic records the variation in scattered-light intensity over a transmission diffuser using a charge-coupled device (CCD)/lens assembly. At the standard operating position, an 11.3° (f/2.5) cone of light is collected. A stray light baffle, debris shield, and antireflection absorbing filter are also incorporated into the diagnostic payload inserted into the target chamber. The imaging parts of the diagnostic (light baffle, vacuum window, filters, lens, and CCD camera) are located outside the target chamber. Five SLUIs have been built and deployed in OMEGA’s ten-inch manipulator diagnostic ports, covering almost 5% of the emission surface, enabling an absolute scattered-light measurement should be within a few percent of the global average. Each SLUI system is calibrated offline, providing absolute scattered-light intensity measurements. Based on the measured point spread function, each diffuser plate image contains over 20 000 independent scattered-light absolute-intensity measurements of the variation over the collection cone. SLUI provides a platform to study scattered light and absorption asymmetries, and their possible sources.

47 OTHER INSTRUMENTATION↗

Quantum efficiency enhancement in simulated nanostructured negative electron affinity GaAs photocathodes

We report nanostructured negative electron affinity GaAs photocathodes for a polarized electron source are studied using finite difference time domain optical simulation. The structures studied are nanosquare columns, truncated nanocones, and truncated nanopyramids. Mie-type resonances in the 700–800 nm waveband, suitable for generation of polarized electrons, are identified. At resonance wavelengths, the nanostructures can absorb up to 99% of the incident light. For nanosquare columns and truncated nanocones, the maximum quantum efficiency (QE) at 780 nm obtained from simulation is 27%, whereas for simulated nanopyramids, the QE is ~21%. The high photocathode quantum efficiency is due to the shift of Mie resonance toward the longer wavelength, leading to increased light absorption. The field profile distribution shows the excitation of dipole and quadrupole modes within the nanostructures at resonant frequencies. This leads to enhanced photoabsorption and photoelectron generation closer to emission surfaces than for a flat photocathode. The enhanced photoabsorption and reduced electron transport distance for the nanostructured photocathode enhance its QE compared to that for the flat surface wafer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

TIME-DEPENDENT, COMPOSITIONALLY DRIVEN CONVECTION IN THE OCEANS OF ACCRETING NEUTRON STARS

We discuss the effect of convection driven by chemical separation at the ocean-crust boundary of accreting neutron stars. We extend the steady-state results of Medin and Cumming to transient accretors, by considering the time-dependent cases of heating during accretion outbursts and cooling during quiescence. During accretion outbursts, inward heat transport has only a small effect on the temperature profile in the outer layers until the ocean is strongly enriched in light elements, a process that takes hundreds of years to complete. During quiescence, however, inward heat transport rapidly cools the outer layers of the ocean while keeping the inner layers hot. We find that this leads to a sharp drop in surface emission at around a week followed by a gradual recovery as cooling becomes dominated by the crust. Such a dip should be observable in the light curves of these neutron star transients, if enough data is taken at a few days to a month after the end of accretion. If such a dip is definitively observed, it will provide strong constraints on the chemical composition of the ocean and outer crust.

79 ASTRONOMY AND ASTROPHYSICS↗

REJECTING PROPOSED DENSE MATTER EQUATIONS OF STATE WITH QUIESCENT LOW-MASS X-RAY BINARIES

Neutrons stars are unique laboratories for discriminating between the various proposed equations of state of matter at and above nuclear density. One sub-class of neutron stars—those inside quiescent low-mass X-ray binaries (qLMXBs)—produce a thermal surface emission from which the neutron star radius (R {sub NS}) can be measured, using the widely accepted observational scenario for qLMXBs, assuming unmagnetized H atmospheres. In a combined spectral analysis, this work first reproduces a previously published measurement of the R {sub NS}, assumed to be the same for all neutron stars, using a slightly expanded data set. The radius measured is R{sub NS}=9.4±1.2 km. On the basis of spectral analysis alone, this measured value is not affected by imposing an assumption of causality in the core. However, the assumptions underlying this R {sub NS} measurement would be falsified by the observation of any neutron star with a mass >2.6 M {sub ☉}, since radii <11 km would be rejected if causality is assumed, which would exclude most of the R {sub NS} parameter space obtained in this analysis. Finally, this work directly tests a selection of dense matter equations of state: WFF1, AP4, MPA1, PAL1, MS0, and three versions of equations of state produced through chiral effective theory. Two of those, MS0 and PAL1, are rejected at the 99% confidence level, accounting for all quantifiable uncertainties, while the other cannot be excluded at >99% certainty.

79 ASTRONOMY AND ASTROPHYSICS↗

Tomography of High-Energy Nuclear Collisions with Photon-Hadron Correlations

Within the next-to-leading order (NLO) perturbative QCD (PQCD) parton model, suppression of away-side hadron spectra associated with a high p{sub T} photon due to parton energy loss is studied in high-energy heavy-ion collisions. Because of the sharp falloff of the gamma-jet spectrum in momentum imbalance p{sub T}{sup jet}-p{sub T}{sup g}amma>0 in NLO PQCD, hadron spectra at large z{sub T}=p{sub T}{sup h}/p{sub T}{sup g}amma > or approx. 1 are more susceptible to parton energy loss and therefore are dominated by surface emission of gamma-associated jets with almost no energy loss, whereas small z{sub T} hadrons mainly come from the volume emission of jets with reduced energy. These lead to different centrality dependence of the gamma-hadron suppression for different values of z{sub T}. Therefore, a complete measurement of the suppression of gamma-triggered hadron spectra allows a true tomographic study of the quark-gluon plasma in high-energy heavy-ion collisions.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

First Results from a Broadband Search for Dark Photon Dark Matter in the 44 to 52 μ eV Range with a Coaxial Dish Antenna

We present first results from a dark photon dark matter search in the mass range from 44 to 52 μ eV (10.7–12.5 GHz) using a room-temperature dish antenna setup called GigaBREAD. Dark photon dark matter converts to ordinary photons on a cylindrical metallic emission surface with area 0.5 m 2 and is focused by a novel parabolic reflector onto a horn antenna. Signals are read out with a low-noise receiver system. A first data taking run with 24 days of data does not show evidence for dark photon dark matter in this mass range, excluding dark photon photon mixing parameters χ ≳ 10 − 12 in this range at 90% confidence level. This surpasses existing constraints by about 2 orders of magnitude and is the most stringent bound on dark photons in this range below 49 μ eV . Published by the American Physical Society 2024

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Impacts of Methane on Carbon Dioxide Storage in Brine Formations

In the context of geological carbon sequestration (GCS), carbon dioxide (CO 2 ) is often injected into deep formations saturated with a brine that may contain dissolved light hydrocarbons, such as methane (CH 4 ). In this multicomponent multiphase displacement process, CO 2 competes with CH 4 in terms of dissolution, and CH 4 tends to exsolve from the aqueous into a gaseous phase. Because CH 4 has a lower viscosity than injected CO 2 , CH 4 is swept up into a ‘bank’ of CH 4 –rich gas ahead of the CO 2 displacement front. On the one hand, this may provide a useful tracer signal of an approaching CO 2 front. On the other hand, the emergence of gaseous CH 4 is undesirable because it poses a leakage risk of a far more potent greenhouse gas than CO 2 if the cap rock is compromised. Open fractures or faults and wells could result in CH 4 contamination of overlying groundwater aquifers as well as surface emissions. We investigate this process through detailed numerical simulations for a large–scale GCS pilot project (near Cranfield, Mississippi) for which a rich set of field data is available. An accurate cubic–plus–association equation–of–state is used to describe the non–linear phase behavior of multiphase brine–CH 4 –CO 2 mixtures, and breakthrough curves in two observation wells are used to constrain transport processes. Furthermore, both field data and simulations indeed show the development of an extensive plume of CH 4 –rich (up to 90 mol%) gas as a consequence of CO 2 injection, with important implications for the risk assessment of future GCS projects.

58 GEOSCIENCES↗

Predicting Nugget Size of Resistance Spot Welds Using Infrared Thermal Videos With Image Segmentation and Convolutional Neural Network

Resistance spot welding (RSW) is a widely adopted joining technique in automotive industry. Recent advancement in sensing technology makes it possible to collect thermal videos of the weld nugget during RSW using an infrared (IR) camera. The effective and timely analysis of such thermal videos has the potential of enabling in situ nondestructive evaluation (NDE) of the weld nugget by predicting nugget thickness and diameter. Deep learning (DL) has demonstrated to be effective in analyzing imaging data in many applications. However, the thermal videos in RSW present unique data-level challenges that compromise the effectiveness of most pre-trained DL models. We propose a novel image segmentation method for handling the RSW thermal videos to improve the prediction performance of DL models in RSW. The proposed method transforms raw thermal videos into spatial-temporal instances in four steps: video-wise normalization, removal of uninformative images, watershed segmentation, and spatial-temporal instance construction. The extracted spatial-temporal instances serve as the input data for training a DL-based NDE model. The proposed method is able to extract high-quality data with spatial-temporal correlations in the thermal videos, while being robust to the impact of unknown surface emissivity. Overall, our case studies demonstrate that the proposed method achieves better prediction of nugget thickness and diameter than predicting without the transformation.

42 ENGINEERING↗