Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

A Comparison of Emerging and Industry Benchmark Photovoltaic Backsheets Between Different Outdoor Locations

Recent interest within the photovoltaic (PV) module industry is largely directed toward enhanced lifetimes in the field, balanced with improved recyclability. Traditionally, fluoropolymer-based backsheets have been used, however, are difficult to recycle. Emerging polyolefin (PO)-based backsheets are more recyclable and can be formulated to be robust. Properties of different fluoropolymer- and non-fluoropolymer-based backsheet coupons and in encapsulated silicon mini modules that have been fielded in Albuquerque, NM and Cocoa, FL are reported here. Seven backsheets were examined: two novel PO's, TPT, APO, PPE, AAA, and KPf. Methods of examination include module electrical performance (I - V flash test), surface morphology (optical microscope and gloss), polymer chemical structure (FTIR), EL imaging, mechanical tensile testing, DC breakdown voltage, DSC (phase transitions), and optical performance (reflectance spectra).

industries↗

Nano structuring of GaAs(100) surface using low energy ion irradiation

Nanostructuring of semi insulating GaAs (100) has been observed after irradiation of 50 keV Ar{sup +} ion beam in a wide angular range of 0 deg. to 60 deg. with respect to surface normal. Atomic Force Microscopy (AFM) analysis shows the formation of nano dots at smaller angle of irradiation. At higher angle of irradiation, self organized ripples were developed on the surface. The rms roughness estimated from the AFM analysis shows exponential growth with angle of irradiation. In the high frequency regime, PSD analysis suggests that surface morphology of the irradiated samples is governed by the surface diffusion and mass transport dominated processes.

36 MATERIALS SCIENCE↗

Epitaxial growth and characterization of magnesium gallate (MgGa 2 O 4 ) thin films by pulsed laser deposition

To advance high power device application of MgGa 2 O 4 , it is imperative to achieve crystalline epitaxial thin films and to observe its materials’ characteristics within a wide range of growth conditions. However, there is no published work on the growth of this promising ultrawide bandgap material till this day. In this study, we report the crystalline growth of MgGa 2 O 4 thin films on c-plane (006) sapphire substrates using the pulsed laser deposition (PLD) technique in a broad range of temperature and oxygen pressure. The temperature range for this crystalline growth was within the temperature range of 300°C to 700°C and a pressure range of 1x10 -1 to 1x10 -3 Torr. Within this parameter range, the structural, chemical, optical, and surface property of MgGa 2 O 4 thin films have been investigated. Specifically, the acquired XRD patterns confirmed the film growth along the [111] preferential crystal orientation in the lattice. Here, the rocking curve measurement of the prominent (222) plane showed an increasing trend of the crystallinity with growth temperature and pressure. Furthermore, the XRD phi (φ) scan demonstrated the six-fold rotational symmetry of the MgGa 2 O 4 films and the epitaxial relationship of 30° between the film and the sapphire substrate. The XPS spectra confirmed the presence of +2 and +3 oxidation state for Mg and Ga respectively, in the films. The direct bandgap of MgGa 2 O 4 films was obtained ~5.27±0.03 eV by analyzing the UV-Vis absorbance spectra using the Tauc equation. The SEM images exhibited a granular surface morphology of the MgGa 2 O 4 films with an increasing trend in the grain size from low to high temperature and pressure. The refractive index and thickness of these films were in the range of ~1.90±0.02 and ~70±2.0 nm, respectively determined by fitting the spectroscopic ellipsometry data.

36 MATERIALS SCIENCE↗

Self-doping effects in epitaxially grown graphene

Self-doping in graphene has been studied by examining single-layer epitaxially grown graphene samples with differing characteristic lateral terrace widths. Low energy electron microscopy was used to gain real-space information about the graphene surface morphology, which was compared with data obtained by angle-resolved photoemission spectroscopy to study the effect of the monolayer graphene terrace width on the low energy dispersions. By altering the graphene terrace width, we report significant changes in the electronic structure and quasiparticle relaxation time of the material, in addition to a terrace width-dependent doping effect.

36 MATERIALS SCIENCE↗

Electronic properties of ultrananocrystalline diamond surfaces.

We have characterized ultrananocrystalline diamond films with different surface terminations by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS). The surface terminations were performed by plasma functionalization in atmospheres of hydrogen, fluorine, and oxygen. XPS proves the dense monolayer coverage of the surface functionalization. AFM and STM show low impact of the plasma treatment on the surface morphology. STS has been used to investigate the surface electronic properties, for H-terminated surfaces the electronic structure is dominated by the sp{sup 3} carbon phase of the grain surfaces; for O- and F-terminated surfaces, however, sp{sup 2} carbon from the grain boundaries seems to determine the surface band gap.

08 HYDROGEN↗

Damage morphology study of high cycle fatigued as-cast Mg–3.0Nd–0.2Zn–Zr (wt.%) alloy

Laser scanning confocal microscopy (LSCM) and Electron back-scattered diffraction (EBSD) were applied to the study of surface morphology variation of as-cast Mg–3.0Nd–0.2Zn–Zr (NZ30K) (wt.%) alloy under tension-compression fatigue test at room temperature. Two kinds of typical damage morphologies were observed in fatigued NZ30K alloy: One was parallel lines on basal planes led by the cumulation of basal slips, called persistent slip markings (PSMs), and the other was lens shaped, thicker and in less density, led by the formation of twinning. The surface fatigue damage morphology evolution was analyzed in a statistical way. The influences of stress amplitude and grain orientation on fatigue deformation mechanisms were discussed and the non-uniform deformation among grains and the PSMs, within twinning were described quantitatively. - Highlights: • Fatigue morphology evolution was studied by Laser Scanning Confocal Microscopy. • 3D morphology of persistent slip markings and twins was characterized. • Non-uniform deformation among grains, the PSMs and twins were quantified. • Initiations of fatigue crack were clearly investigated.

36 MATERIALS SCIENCE↗

Antiferromagnetic Ordering at Room Temperature in Co-Doped Sb{sub 2}Te{sub 3} Topological Insulators

Structural and magnetic properties of Co-doped Sb{sub 2}Te{sub 3} topological insulators have been investigated. Surface morphology was studied using scanning electron microscope (SEM) and atomic force microscope (AFM). X-ray photo electron spectroscopy (XPS) study reveals the mixed states of Co in Co{sup 2+} and Co{sup 3+}. Magnetic study indicates that the substitution of Co in Sb{sub 2}Te{sub 3} not only tune the materials from diamagnetic to antiferromagnetic (even at room temperature) but also propose a promising materials for antiferromagnetic TI which may be useful even for room temperature applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermal Behavior During the Selective Laser Melting Process of Ti-6Al-4V Powder in the Point Exposure Scan Pattern

Currently, there are two main scan patterns, including the continuous exposure scan pattern and the point exposure scan pattern, during the selective laser melting (SLM) process. The point exposure scan pattern allows a three-dimensional (3-D) printer to build finer detail features as a static molten pool that is more stable than a dynamic one. However, there has been limited theoretical research on the thermal behavior characteristics during the process in the point exposure scan pattern. Therefore, in this study, the simulation of thermal behavior during SLM of Ti-6Al-4V powder in the point exposure scan pattern was performed. The temperature evolution behavior of different positions and the effects of exposure time on the temperature evolution behavior of different positions, temperature distributions, and dimensions of the molten pool were investigated. The results showed that the direct exposure position and unexposed position had significantly different temperature evolution behaviors under a given condition, and the changed exposure time had the greatest influence on the direct exposure position compared with unexposed position. Moreover, the thermal accumulation effect of a former exposure point on a later one decreased with increasing exposure time. In addition, with the increase of exposure time, the maximum temperature of the molten pool was enhanced and the surface morphology of the molten pool changed from an approximate ellipse to an approximate circle. Besides, the molten pool dimensions were found to increase with exposure time, which indicated that the exposure time played an important role in the stability of the molten pool and the metallurgical bonding in the process. Furthermore, the dimensions of the molten pool and metallurgical bonding in the cross-sectional view were obtained through experiments. Good agreement was obtained when comparing the simulated results with the experimental ones.

36 MATERIALS SCIENCE↗

Fluorographite-co-polydimethylsiloxane coated polyvinylidene-fluoride membrane for desalination of highly saline water with humic acid in direct contact membrane distillation

Highlights: • Surface modifications by FGi particles with PDMS binder of PVDF microporous membranes shown improvement in DCMD. • LEP with DI water & performance of M2-M4 modified membranes in DCMD was enhanced with 1M NaCl & 10 ppm HA feed solution. • Amphiphobicity was evidenced by CA with low surface tension liquids upto 38 dyne/cm as well as with canola oil. • EDX analysis proved enhancement in FC ratio and membrane surface analysis lead to understand enhanced performance in DCMD. Membranes with amphiphobic properties are crucial for desalination of concentrated saline water with organic foulant by membrane distillation. In this research, we coated Fluorographite (FGi) particles on polyvinylidene-fluoride (PVDF) flat sheet membranes with 0.8% v/v polydimethylsiloxane (PDMS) as binder by filtration coating method. We evaluated its amphiphobicity via contact angles which were observed by DI water, canola oil and organic solutions as mimicking for oleophobicity. Surface modifications by FGi particles on the surface of membranes was introduced with PDMS binder which brought bifunctionality of amphiphobicity to enhance hydrophobicity and oleophobicity. We also investigated performance of coated membranes in direct contact membrane distillation (DCMD) with 1 molar concentrated NaCl solution along with humic acid being organic foulant and compared with virgin membrane (M1 membrane) and Liquid entry pressure (LEP) was also evaluated. LEP was measured by dynamic method which shown considerable improvement in coated membranes. M3 membrane showed overall better performance in terms of salt rejection higher than 99.87% and flux as compared to M1 membrane. Furthermore, the evaluation of surface characterizations was done by FESEM with EDX, AFM and FTIR. Surface morphology confirmed the coating of FGi on membrane surface while EDX evidenced increase in atomic percent of fluorine in turn F:C ratio.

54 ENVIRONMENTAL SCIENCES↗

Multicycle study on chemical-looping combustion of simulated coal gas with a CaSO{sub 4} oxygen carrier in a fluidized bed reactor

The cyclic test of a CaSO{sub 4}-based oxygen carrier (natural anhydrite) in alternating reducing simulated coal gas and oxidizing conditions was performed at 950{degree}C in a fluidized bed reactor at atmospheric pressure. A high concentration of CO{sub 2} was obtained in the reduction. The H{sub 2} and CO conversions and CO{sub 2} yield increased initially and final decreased significantly. The release of SO{sub 2} and H{sub 2}S during the cyclic test was found to be responsible for the decrease of reactivity of a CaSO{sub 4} oxygen carrier. The oxygen carrier conversion after the reduction reaction decreased gradually in the cyclic test. Through the comparison of mass-based reaction rates as a function of mass conversion at typical cycles, it was also evident that the reactivity of a CaSO{sub 4} oxygen carrier increased for the initial cycles but finally decreased after around 15 cycles. X-ray diffraction analysis revealed that the presence and intensity of the reduction sulfur species was in accordance with the results of gas conversion. The content of CaO was higher than expected, suggesting the formation of SO{sub 2} and H{sub 2}S during the cycles. Surface morphology analysis demonstrates that the natural anhydrite particle surface varied from impervious to porous after the cyclic test. It was also observed that the small grains on the surface of the oxygen carrier sintered in the cyclic tests. Energy-dispersive spectrum analysis also demonstrated the decrease of oxygen intensity after reduction, and CaO became the main component after the 20th oxidation. Pore structure analysis suggested that the particles agglomerated or sintered in the cyclic tests. The possible method for sulfur mitigation is proposed. Finally, some basic consideration on the design criteria of a CLC system for solid fuels using a CaSO{sub 4} oxygen carrier is discussed by the references and provides direction for future work. 49 refs., 10 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Manganese-doped indium oxide and its application in organic light-emitting diodes

Thin films of manganese-doped indium oxide (IMO) deposited by electron beam evaporation have been investigated as anodes in organic light-emitting diodes (OLEDs). The IMO films have a high work function of 5.35 eV, a desirable surface morphology with an average roughness of 1.1 nm, a high average optical transmittance of 87.2% in the visible region, and a maximum optical transmittance of 92% at 460 nm. It is demonstrated that an IMO anode can effectively improve hole injection at the anode/organic interface, resulting in OLEDs with an increased electroluminescent efficiency.

36 MATERIALS SCIENCE↗

Analysis of defects in GaAsN grown by chemical beam epitaxy on high index GaAs substrates

The lattice defects in GaAsN grown by chemical beam epitaxy on GaAs 311B and GaAs 10A toward [110] were characterized and discussed by using deep level transient spectroscopy (DLTS) and on the basis of temperature dependence of the junction capacitances (C{sub J}). In one hand, GaAsN films grown on GaAs 311B and GaAs 10A showed n-type and p-type conductivities, respectively although the similar and simultaneous growth conditions. This result is indeed in contrast to the common known effect of N concentration on the type of conductivity, since the surface 311B showed a significant improvement in the incorporation of N. Furthermore, the temperature dependence of C{sub J} has shown that GaAs 311B limits the formation of N-H defects. In the other hand, the energy states in the forbidden gap of GaAsN were obtained. Six electron traps, E1 to E6, were observed in the DLTS spectrum of GaAsN grown on GaAs 311B, with apparent activation energies of 0.02, 0.14, 0.16, 0.33, 0.48, and 0.74 eV below the bottom edge of the conduction band, respectively. In addition, four hole traps, H1 to H4, were observed in the DLTS spectrum of GaAsN grown on GaAs 10A, with energy depths of 0.13, 0.20, 0.39, and 0.52 eV above the valence band maximum of the alloy, respectively. Hence, the surface morphology of the GaAs substrate was found to play a key factor role in clarifying the electrical properties of GaAsN grown by CBE.

36 MATERIALS SCIENCE↗

Effect of Ag addition to L1{sub 0} FePt and L1{sub 0} FePd films grown by molecular beam epitaxy

L1{sub 0} ordered FePt-Ag (5 nm) and FePd-Ag (5 nm) films were grown on MgO (001) substrate at temperatures of 250–400 °C by using molecular beam epitaxy method, and their crystal and surface structures, perpendicular magnetic anisotropies and Curie temperatures were investigated. In the case of FePt-Ag, Ag addition with the amount of 10–20 at. % was effective to promote L1{sub 0} ordering and granular growth, resulting in the increase of the perpendicular magnetic anisotropy and coercivity of the FePt-Ag films. On the other hand, in the case of FePd-Ag, Ag addition changed the surface morphology from island to continuous film associated with the reductions of its coercivity and perpendicular anisotropy. The variations of lattice constants and Curie temperature with Ag addition were significantly different between FePt-Ag and FePd-Ag. For FePd-Ag, the c and a axes lattice spacings and Curie temperature gradually changed with increasing Ag content, while they unchanged for FePt-Ag. These results suggest the possibility of the formation of FePdAg alloy in FePd-Ag, while Ag segregation in FePt-Ag.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Metalorganic chemical vapor deposition growth of high-mobility AlGaN/AlN/GaN heterostructures on GaN templates and native GaN substrates

Severe surface decomposition of semi-insulating (SI) GaN templates occurred in high-temperature H{sub 2} atmosphere prior to epitaxial growth in a metalorganic chemical vapor deposition system. A two-step heating process with a surface stabilization technique was developed to preserve the GaN template surface. Utilizing the optimized heating process, a high two-dimensional electron gas mobility ∼2000 cm{sup 2}/V·s was obtained in a thin AlGaN/AlN/GaN heterostructure with an only 100-nm-thick GaN spacer layer homoepitaxially grown on the GaN template. This technique was also demonstrated viable for native GaN substrates to stabilize the surface facilitating two-dimensional growth of GaN layers. Very high residual silicon and oxygen concentrations were found up to ∼1 × 10{sup 20 }cm{sup −3} at the interface between the GaN epilayer and the native GaN substrate. Capacitance-voltage measurements confirmed that the residual carbon doping controlled by growth conditions of the GaN epilayer can be used to successfully compensate the donor-like impurities. State-of-the-art structural properties of a high-mobility AlGaN/AlN/GaN heterostructure was then realized on a 1 × 1 cm{sup 2} SI native GaN substrate; the full width at half maximum of the X-ray rocking curves of the GaN (002) and (102) peaks are only 21 and 14 arc sec, respectively. The surface morphology of the heterostructure shows uniform parallel bilayer steps, and no morphological defects were noticeable over the entire epi-wafer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrodeposition of Zn based nanostructure thin films for photovoltaic applications

We present here a systematic study on the synthesis thin films of various ZnO, CdO, Zn{sub x}Cd{sub 1-x} (O) and ZnTe nanostructures by electrodeposition technique with ZnCl{sub 2,} CdCl{sub 2} and ZnSO{sub 4} solution as starting reactant. Several reaction parameters were examined to develop an optimal procedure for controlling the size, shape, and surface morphology of the nanostructure. The results showed that the morphology of the products can be carefully controlled through adjusting the concentration of the electrolyte. The products present well shaped Nanorods arrays at specific concentration and temperature. UV-VIS spectroscopy and X-ray diffraction results show that the product presents good crystallinity. A possible formation process has been proposed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation on single walled carbon nanotube thin films deposited by Langmuir Blodgett method

Langmuir Blodgett is a technique to deposit a homogeneous film with a fine control over thickness and molecular organization. Thin films of functionalized SWCNTs have been prepared by Langmuir Blodgett method. The good surface spreading properties of SWCNTs at air/water interface are indicated by surface pressure-area isotherm and the monolayer formed on water surface is transferred onto the quartz substrate by vertical dipping. A multilayer film is thus obtained in a layer by layer manner. The film is characterized by Atomic Force Microscope (AFM), UV-Vis-NIR spectroscopy and FTIR.AFM shows the surface morphology of the deposited film. UV-Vis-NIR spectroscopy shows the characteristic peaks of semiconducting SWCNTs. The uniformity of LB film can be used further in understanding the optical and electrical behavior of these materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effects of defect density on ultrathin graphene-based metal diffusion barriers

The authors investigated the effects of defect density on the performance of monolayer graphene as a barrier to metal diffusion. The defects were introduced to the graphene by controlled ultraviolet-ozone irradiation. The barrier performance of pristine graphene was found to be superior to that of defective graphene at temperatures up to 700 °C. Changes in surface morphology were more prevalent in the defective graphene-based films than in the pristine graphene-based film; the thermal stability of graphene films depends on their defect density. Defect density was found to be a determining factor in the barrier performance of graphene.

42 ENGINEERING↗

Formation of Ordered Silicon Structures on a Graphite Surface

The possibility of formation of ordered silicon structures, including silicene, on the graphite substrate surface has been studied. The effect of various conditions of depositing silicon atoms on a finite structure has also been studied. The data on the surface morphology has been obtained by atomic force microscopy, and the electronic structure has been studied by Auger electron spectroscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗