Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Operating Stresses and Their Effects on Degradation of LSM-Based SOFC Cathodes

The performance of solid oxides fuel cells (SOFCs) with four different Mn excess of lanthanum strontium manganite (LSM) -based cathodes were examined under different temperatures (1,000 °C, 900 °C), current densities (0, 380, and 760 mA cm -2 ), and cathode atmospheres (p O 2 )=0.1,0.15,0.21) for durations ranging from 58 to 1,008 h. Each yttria-stabilized zirconia (YSZ) electrolyte-supported “button” cell had a porous Ni/YSZ composite anode and a porous LSM/YSZ composite cathode. The cells’ output voltage versus time were recorded and electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) measurements were performed every 24 hours. The total area specific resistance (ASR) was calculated from these measurements. The values of ASR from both EIS and LSV were comparable between each other but lower than that from durability test. Distribution of relaxation times (DRT) analysis was performed to investigate the electrochemical processes and their corresponding relaxation frequencies as well as their attributions to the total ASR. The series resistance and parallel resistance that obtained from the equivalent circuit fit of the Nyquist plot were higher at low temperature and low p O 2 regardless of LSM compositions. The area of the peaks derived from DRT analysis increased with time during individual tests. The microstructures of the tested cells were examined using scanning electron microscopy and energy-dispersive x-ray spectroscopy (SEM/EDS). Manganese oxide particles were observed near the cathode-electrolyte interface after prolonged (1,008 h) testing in air of a cell with LSM of 11% manganese excess, and after a short test (58 h) under low oxygen (p O 2 = 0.10) in a cell with LSM of 5% manganese excess. However, the role of MnOx in cell degradation is still unknown.

08 HYDROGEN↗
DOE OSTI2024

Operando investigations of the solid electrolyte interphase in the lithium mediated nitrogen reduction reaction

The lithium-mediated nitrogen reduction reaction (Li-NRR) represents a promising approach for electrochemical nitrogen activation, in which the solid electrolyte interphase (SEI) layer formed on the electrochemically plated lithium plays a key role. Herein, we used time-resolved, operando, grazing incidence wide-angle X-ray scattering (GI WAXS) to identify SEI species and reaction intermediates in the Li-NRR, comparing LiBF 4 and LiClO 4 as electrolyte salts. In this study, we demonstrated how the SEI composition influences the Li-NRR performance by regulating proton transport to the plated Li. When LiBF 4 is used as the electrolyte salt, the formation of LiF and lithium ethoxide (LiEtO) is observed. Reaction intermediates such as LiH and LiN x H y species were found and provide insight into reaction pathways towards undesired and desired products, respectively. Observed restructuring of the Cu (111) single crystal substrate also indicates interaction with plated Li that could possibly influence the Li-NRR performance. Together, these experiments give molecular insight into how to design Li-NRR systems and their SEI layers for optimal performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Chemical Interplay of Silicon and Graphite in a Composite Electrode in SEI Formation

In this study, we investigated the effect of the Si/graphite weight ratio in half-cells on the solid electrolyte interphase (SEI) layer's chemistry. The nominal concentrations of active materials were (wt % Si/wt % Gr) 15/73, 30/58, 60/28, and 80/0. The electrolyte in the cells consisted of either 1.2 M LiPF 6 in ethylene carbonate/ethyl methyl carbonate (3:7 by wt) or 1.2 M LiPF 6 in ethylene carbonate:ethyl methyl carbonate (3:7 by wt) + 10 wt % fluoroethylene carbonate. These coin cells were cycled five times at the C/10 rate. As expected, the addition of silicon to the electrode significantly increased the measured capacity. Examination of the aged composite material showed that the electrolyte influenced the concentration of chemical environments on the surface. Depth profiling revealed that these concentrations of surface environments changed with sputtering time. A statistics-of-mixtures model was used to deconvolute how silicon and graphite interacted during the formation of these species and how the interaction changed with depth.

25 ENERGY STORAGE↗
DOE OSTI2023

Pitch Carbon-coated Ultrasmall Si Nanoparticle Lithium-ion Battery Anodes Exhibiting Reduced Reactivity with Carbonate-based Electrolyte

Silicon anodes for lithium-ion batteries (LIBs) have the potential for higher energy density compared to conventionally used graphite-based LIB anodes. However, silicon anodes exhibit poor cycle and calendar lifetimes due to mechanical instabilities and high chemical and electrochemical reactivity with the carbonate-based electrolytes that are typically used in LIBs. In this work, we synthesize a pitch carbon-coated silicon nanoparticle composite active material for LIB anodes that exhibits reduced chemical reactivity with carbonate-based electrolytes compared to an uncoated silicon anode. Silicon primary particle sizes less than 10 nm diameter minimize micro-scale mechanical degradation of the anode composite, while conformal coatings of pitch carbon minimize the parasitic reactions between the silicon and the electrolyte. When matched with a high voltage NMC622 (LiNi 0.6 Mn 0.2 Co 0.2 O 2 ) cathode, the pitch carbon-coated silicon anode retains approximately 75% of its initial capacity at the end of 1000 cycles. Increasing the areal loading of the pitch carbon-coated silicon anodes to realize energy density improvements over graphite anodes results in severe mechanical degradation on the electrode level, highlighting a remaining challenge to be addressed in future work.

25 ENERGY STORAGE↗
DOE OSTI2022

Co-intercalation-free ether electrolytes for graphitic anodes in lithium-ion batteries

Carbonate-based electrolytes are widely used in Li-ion batteries but are limited by a small operating temperature window and poor cycling with silicon-containing graphitic anodes. The lack of non-carbonate electrolyte alternatives such as ether-based electrolytes is due to undesired solvent co-intercalation that occurs with graphitic anodes. Here, we show that fluoroethers are the first class of ether solvents to intrinsically support reversible lithium-ion intercalation into graphite without solvent co-intercalation at conventional salt concentrations. In full cells using a graphite anode, they enable 10-fold higher energy densities compared to conventional ethers, and better thermal stability over carbonate electrolytes (operation up to 60 °C) by producing a robust solvent-derived solid electrolyte interphase (SEI). As single-solvent–single-salt electrolytes, they remarkably outperform carbonate electrolytes with fluoroethylene carbonate (FEC) and vinylene carbonate (VC) additives when cycled with graphite–silicon composite anodes. In conclusion, our molecular design strategy opens a new class of electrolytes that can enable next generation Li-ion batteries with higher energy density and a wider working temperature window.

25 ENERGY STORAGE↗
DOE OSTI2026

Understanding Discharge‐Driven Growth of Cathode Impedance in Ni‐Rich NMC Cathodes

Degradation of LiNi x Mn y Co 1-x-y O 2 (NMC)-based lithium-ion batteries depends strongly on cut-off voltage ranges. In addition to the high upper cut-off voltage, a high depth of discharge (i.e., lower cut-off voltage) significantly worsens cathode impedance growth and capacity fade during long-term cycling. However, there is currently no consensus on the mechanism behind the negative role of a deep discharge. Here, this phenomenon was investigated in graphite||NMC cells with single-crystal cathodes (LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC622) or LiNi 0.76 Co 0.14 Mn 0.10 O 2 (NMC76)) using targeted aging protocols (constant high-voltage holds vs. charge–discharge cycling), while monitoring transition-metal (TM) dissolution, cathode-electrolyte interface (CEI) impedance, and NMC surface composition. We demonstrate a correlation between discharge-driven CEI impedance growth and increased TM dissolution. Furthermore, this degradation pathway is more pronounced in lower-Ni NMC622 than in higher-Ni (NMC76) under comparable delithiation states at charge, with both compositions undergoing the H2→H3 phase transition. X-ray photoelectron spectroscopy (XPS) reveals NMC composition-dependent evolution of surface lattice oxygen and restructured surface layer composition between charged and discharged states. These findings add mechanistic depth to the role of discharge as an active driver of interfacial degradation and provide new insights into its composition dependence.

25 ENERGY STORAGE↗
DOE OSTI2020

Regulating electrodeposition morphology of lithium: towards commercially relevant secondary Li metal batteries

Lithium, the lightest and most electronegative metallic element, has long been considered the ultimate choice as a battery anode for mobile, as well as in some stationary applications. The high electronegativity of Li is, however, a double-edged sword—it facilitates a large operating voltage when paired with essentially any cathode, promising a high cell-level energy density. It is also synonymous with a high chemical reactivity and low reduction potential. The interfaces a Li metal anode forms with any other material (liquid or solid) in an electrochemical cell are therefore always mediated by one or more products of its chemical or electrochemical reactions with that material. The physical, crystallographic, mechanical, electrochemical, and transport properties of the resultant new material phases (interphases) regulate all interfacial processes at a Li metal anode, including electrodeposition during battery recharge. This Review takes recent efforts aimed at manipulating the structure, composition, and physical properties of the solid electrolyte interphase (SEI) formed on an Li anode as a point of departure to discuss the structural, electrokinetic, and electrochemical requirements for achieving high anode reversibility. An important conclusion is that while recent reports showing significant advances in the achievement of highly reversible Li anodes, e.g. as measured by the coulombic efficiency (CE), raise prospects for as significant progress towards commercially relevant Li metal batteries, the plateauing of achievable CE values to around 99 ± 0.5% apparent from a comprehensive analysis of the literature is problematic because CE values of at least 99.7%, and preferably >99.9% are required for Li metal cells to live up to the potential for higher energy density batteries offered by the Li metal anode. On this basis, we discuss promising approaches for creating purpose-built interphases on Li, as well as for fabricating advanced Li electrode architectures for regulating Li electrodeposition morphology and crystallinity. Considering the large number of physical and chemical factors involved in achieving fine control of Li electrodeposition, we believe that achievement of the remaining ~0.5% in anode reversibility will require fresh approaches, perhaps borrowed from other fields. We offer perspectives on both current and new strategies for achieving such Li anodes with the specific aim of engaging established contributors and newcomers to the field in the search for scalable solutions.

25 ENERGY STORAGE↗
NASA NTRS1975

Investigation of electroforming techniques, literature analysis report

A literature analysis is presented of reports, specifications, and documented experiences with the use of electroforming to produce copper and nickel structures for aerospace and other engineering applications. The literature period covered is from 1948 to 1974. Specific effort was made to correlate mechanical property data for the electrodeposited material with known electroforming solution compositions and operating conditions. From this survey, electrolytes are suggested for selection to electroform copper and nickel outer shells on regeneratively cooled thrust chamber liners, and other devices subject to thermal and pressure exposure, based on mechanical properties obtainable, performance under various thermal environments, and ease of process control for product reproducibility. Processes of potential value in obtaining sound bonds between electrodeposited copper and nickel and copper alloy substrates are also discussed.

Malone, G. A.↗
NASA NTRS1977

Analysis of metabolic energy utilization in the Skylab astronauts

Skylab biomedical data regarding man's metabolic processes for extended periods of weightlessness is presented. The data was used in an integrated metabolic balance analysis which included analysis of Skylab water balance, electrolyte balance, evaporative water loss, and body composition. A theoretical analysis of energy utilization in man is presented. The results of the analysis are presented in tabular and graphic format.

Leonard, J. I.↗
NASA NTRS2008

Fuel-Cell Electrolytes Based on Organosilica Hybrid Proton Conductors

A new membrane composite material that combines an organosilica proton conductor with perfluorinated Nafion material to achieve good proton conductivity and high-temperature performance for membranes used for fuel cells in stationary, transportation, and portable applications has been developed. To achieve high proton conductivities of the order of 10(exp -1)S/cm over a wide range of temperatures, a composite membrane based on a new class of mesoporous, proton-conducting, hydrogen-bonded organosilica, used with Nafion, will allow for water retention and high proton conductivity over a wider range of temperatures than currently offered by Nafion alone. At the time of this reporting, this innovation is at the concept level. Some of the materials and processes investigated have shown good proton conductivity, but membranes have not yet been prepared and demonstrated.

Narayan, Sri R.↗
DOE OSTI2022

Nanoscale Three-Dimensional Imaging of Degradation in Composite Si-Containing Anodes

The use of silicon (Si) in next-generation lithium-ion battery (LIB) anodes has the potential to dramatically improve electrochemical performance over current LIB graphite (Gr) anodes, due to silicon’s higher specific capacity.1 However, widespread implementation of Si-containing anodes is inhibited by issues such as significant Si volume expansion during lithiation and an unstable solid-electrolyte interphase (SEI), resulting in unreliable performance and poor cycle life. Currently, composite anodes with both Si and graphite active materials are used to increase capacity and mitigate some of the limitations associated with Si. In composite electrodes with a heterogeneous distribution of components with varying electrical properties (including Si, Gr, conductive carbon additive, and binder), it is important to understand the local distribution of each component to correlate with electrochemical processes, particularly localized degradation and heterogeneous aging, and to optimize performance. To investigate Si-containing composite anodes in the nanoscale, we use scanning spreading resistance microscopy (SSRM), a form of scanning probe microscopy (SPM) that probes local electronic resistivity. By examining the intrinsic electronic resistivity contrast between the anode components, separate phases can be distinguished and understood within the composite structure.2 This work studies the effect of electrochemical cycling in two different electrolytes on component distribution and aging by comparing the electrical and structural evolution of composite Si-graphite electrodes and SEI before and after charge-discharge cycling. 1. W. J. Zhang. A review of the electrochemical performance of alloy anodes for lithium-ion batteries J. Power Sources 196 13–24 (2011). 2. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. Finegan, S.-D. Han and S. DeCaluwe: Three-Dimensional Mapping of Resistivity and Microstructure of Composite Electrodes for Lithium-Ion Batteries. ACS Nano Letters Accepted (2020).

ADVANCED PROPULSION SYSTEMS↗
NASA NTRSDate not supplied

Design Considerations for Practical Li-S Battery Components for Electric Aviaiton

The development of high-energy, high-safety, and high-power batteries beyond electric automobile requirements is vital for future electric aviation applications. The transition to non-volatile solid-state electrolytes (SSE) promises many advantages over traditional flammable liquid electrolytes, and may also be an enabling technology for next generation chemistries. However, significant manufacturing challenges must be overcome before the adoption of such technology. Electrolytes developed in this study were produced as sulfide-polymer composites with densified thicknesses between 20-30 microns using a tape-casting technique and elastomer binder [1]. The composites were determined to retain reasonable ionic conductivity with improved flexibility and scalability critical for practical manufacturing of such cells. Films were produced 10-15 times thinner than comparable bulk powder electrolytes and within the range of commercial polyolefin separators (25 micron) used in commercial liquid containing lithium-ion cells. Composite conductivities were maintained above 0.2mS/cm, which holds promise for future electric aviation applications. Processing techniques are investigated to further improve electrochemical performance.

battery↗
DOE OSTI2021

Interfacial Effects on Transport Coefficient Measurements in Li-ion Battery Electrolytes

Development of Li + -containing electrolytes with improved transport properties requires reliable, reproducible, and ideally low volume techniques to rigorously understand ion-transport with varying composition. Precisely measuring the complete set of transport coefficients in liquid electrolytes under battery-relevant operating conditions is difficult and the reliability of these methods are sparsely described in electrolyte transport literature. In this work, we apply a potentiostatic polarization-based transport characterization approach typically used for polymer electrolytes to liquid electrolyte systems in an attempt to fully measure all transport coefficients (conductivity, total salt diffusion coefficient, thermodynamic factor and transference number) for the model system of LiPF 6 in an ethylene carbonate—ethyl methyl carbonate (EC:EMC) mixture. Using systematic timescale and statistical analyses, we find that transport coefficients measured using potentiostatic polarization of Li-Li symmetric cells exhibit strong correlation to Li electrode interfacial resistance, indicating that such methods are probing both bulk and interfacial phenomena. This reveals a major roadblock in characterizing electrolyte systems where the interfacial resistance is significantly larger than ohmic electrolyte resistance. As a result, we find that methods that rely on potentiostatic Li metal stripping/plating do not readily result in reliable liquid electrolyte transport coefficients, unlike similar methods for solid polymer electrolytes, where interfacial resistances are typically smaller than electrolyte resistances at the elevated temperatures typically of interest for such electrolytes.

25 ENERGY STORAGE↗
NASA NTRS2010

Optimized Li-Ion Electrolytes Containing Fluorinated Ester Co-Solvents

A number of experimental lithium-ion cells, consisting of MCMB (meso-carbon microbeads) carbon anodes and LiNi(0.8)Co(0.2)O2 cathodes, have been fabricated with increased safety and expanded capability. These cells serve to verify and demonstrate the reversibility, low-temperature performance, and electrochemical aspects of each electrode as determined from a number of electrochemical characterization techniques. A number of Li-ion electrolytes possessing fluorinated ester co-solvents, namely trifluoroethyl butyrate (TFEB) and trifluoroethyl propionate (TFEP), were demonstrated to deliver good performance over a wide temperature range in experimental lithium-ion cells. The general approach taken in the development of these electrolyte formulations is to optimize the type and composition of the co-solvents in ternary and quaternary solutions, focusing upon adequate stability [i.e., EC (ethylene carbonate) content needed for anode passivation, and EMC (ethyl methyl carbonate) content needed for lowering the viscosity and widening the temperature range, while still providing good stability], enhancing the inherent safety characteristics (incorporation of fluorinated esters), and widening the temperature range of operation (the use of both fluorinated and non-fluorinated esters). Further - more, the use of electrolyte additives, such as VC (vinylene carbonate) [solid electrolyte interface (SEI) promoter] and DMAc (thermal stabilizing additive), provide enhanced high-temperature life characteristics. Multi-component electrolyte formulations enhance performance over a temperature range of -60 to +60 C. With the need for more safety with the use of these batteries, flammability was a consideration. One of the solvents investigated, TFEB, had the best performance with improved low-temperature capability and high-temperature resilience. This work optimized the use of TFEB as a co-solvent by developing the multi-component electrolytes, which also contain non-halogenated esters, film forming additives, thermal stabilizing additives, and flame retardant additives. Further optimization of these electrolyte formulations is anticipated to yield improved performance. It is also anticipated that much improved performance will be demonstrated once these electrolyte solutions are incorporated into hermetically sealed, large capacity prototype cells, especially if effort is devoted to ensure that all electrolyte components are highly pure.

Prakash, G. K. Surya↗
DOE OSTI2025

Composite Behavior of Nanopore Array Large Memristors

Synthetic nanopores were recently demonstrated with memristive and nonlinear voltage-current behaviors, akin to ion channels in a cell membrane. Such ionic devices are considered a promising candidate for the development of brain-inspired neuromorphic computing techniques. In this work, we show the composite behavior of nanopore-array large memristors, formed with different membrane materials, pore sizes, electrolytes, and device arrangements. Anodic aluminum oxide (AAO) membranes with 5 nm and 20 nm diameter pores and track-etched polycarbonate (PCTE) membranes with 10 nm diameter pores are tested and shown to demonstrate memristive and nonlinear behaviors with approximately 107–1010 pores in parallel when electrolyte concentration across the membranes is asymmetric. Ion diffusion through the large number of channels induces time-dependent electrolyte asymmetry that drives the system through different memristive states. The behaviors of series composite memristors with different configurations are also presented. In addition to helping understand fluidic devices and circuits for neuromorphic computing, the results also shed light on the development of field-assisted ion-selection-membrane filtration techniques as well as the investigations of large neurons and giant synapses. Further work is needed to de-embed parasitic components of the measurement setup to obtain intrinsic large memristor properties.

Chemistry↗
NASA NTRSDate not supplied

Computationally Guided Development of Components for High Energy Density Solid-State Lithium-Sulfur Batteries

All electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The most challenging of these technical barriers to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria1. The performance metrics for eVTOL craft, such as specific energy, specific power, and safety, exceed those of electric automobiles by a factor of two to four. Current state-of-the-art (SOA) lithium-ion batteries are incapable of meeting the key performance criteria of energy and safety for eVTOL. Therefore, next generation advanced chemistries and designs must be developed to meet required performance metrics for electric aviation2. Beyond lithium-ion chemistries, such as lithium-sulfur, show promise in their high energy, while limitations exist in their power and cyclability due to low electrical conductivity and high intermediate solubility in organic liquid electrolytes. Several strategies to overcome the low electrical conductivity involve the use of selenium as a dopant in the active sulfur material, along with the incorporation of 2-dimensional electron-conducting holey-graphene to improve the composite cathodes electronic conductivity. Furthermore, combining this chemistry with a solid-electrolyte avoids the components’ dissolution issues3. However, the development of composite solid-state cathodes is non-trivial as several components must be intimately mixed so that the active component has sufficient access to both electrons and lithium ions to undergo full electrochemical conversion. Mathematical modeling of battery components can assist experimental design through a robust and rigorous combination of computational modeling techniques covering multiple length scales. The objective is to leverage modern computational materials methods combined with battery multiphysics tools to develop radically advanced compatible cathode and electrolyte materials, build and test solid state lithium-sulfur cells and packs. A NASA-based cross-organizational team of high-powered experts combined integrated computational predictive modeling, fundamental chemistry analysis, advanced material science, and battery cell development to tackle this very challenging, multidisciplinary problem. This presentation will show a multiscale computational modeling approach that has produced a novel particle dynamics method called Solid Electrolyte Sphere Approximation Model (SESAM). SESAM modeling targets the 1-10 µm scale structures and provides electromechanical and grain interactions for predictive design guidelines for the manufacturing of solid-state components. Parameters such as particle size and volume fraction of the constituent materials were modeled and experimentally fabricated to optimize electrochemical performance through improved microstructure design. Experimental feedback was provided through ionic and electronic conductivity assessment and structural analysis of developed materials and cell components.

battery↗
DOE OSTI2019

All-Solid-State Batteries Using Rationally Designed Garnet Electrolyte Frameworks

Functioning bulk-type all-solid-state batteries in a practical form factor with composite positive electrodes, using Al-substituted Li 7 La 3 Zr 2 O 12 (LLZO) as the solid electrolyte, have been demonstrated for the first time. The devices incorporate bilayers composed of dense LLZO membranes and porous LLZO scaffolds infiltrated with LiNi 0.6 Mn 0.2 Co 0.2 O 2 and other components as positive electrodes, combined with lithium anodes. The porous scaffolds are prepared using an easily scaled freeze-tape-casting method. The unidirectional pores of the scaffold facilitate infiltration of cathode components and shorten lithium ion diffusion path lengths, while the addition of a soft ionically conductive solid to the scaffold ensures good contact among the components.

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of Water Concentration in LiPF 6 -Based Electrolytes on the Formation, Evolution, and Properties of the Solid Electrolyte Interphase on Si Anodes

A trace amount of water in an electrolyte is one of the factors detrimental to the electrochemical performance of silicon (Si)-based lithium-ion batteries that adversely affect the formation and evolution of the solid electrolyte interphase (SEI) on Si-based anodes and change its properties. Thus far, a lack of fundamental and mechanistic understanding of SEI formation, evolution, and properties in the presence of water has inhibited efforts to stabilize the SEI for improved electrochemical performance. As such, we investigated the SEI formed in a Gen2 electrolyte (1.2 M LiPF6 in ethylene carbonate/ethyl methyl carbonate, 3:7 wt %, water content: <10 ppm) with and without additional water (50 ppm) at varying potentials (1.0, 0.5, 0.2, and 0.01 V vs Li/Li + ). The impact of additional water on the morphological, (electro)chemical, and structural properties of SEI was studied using microscopic (atomic force microscopy and scanning spreading resistance microscopy) and spectroscopic (X-ray photoelectron spectroscopy, attenuated total reflection Fourier-transform infrared spectroscopy, and time-of-flight secondary ion mass spectrometry) techniques. The SEI exhibits both potential- and water concentration-dependent trends in its morphology and chemical composition. The presence of additional water in the electrolyte causes parasitic reactions, which onset at ~1.0 V, resulting in a reduction of electrolyte components and result in the formation of an insulating, fluorophosphate-rich SEI. In addition, hydrolysis of LiPF 6 creates hydrofluoric acid, which reacts with the surface oxide layer on the Si electrode, leading to a pitted and inhomogeneous SEI structure.

36 MATERIALS SCIENCE↗