Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Fatigue retardation due to creep in a fibrous composite

Experiments performed to determine the effects of temperature and creep strain on the fatigue life of a graphite/epoxy composite laminate show that (1) sustained periods of static loading have significant retardation effects on the fatigue degradation rate of the laminated composite, and (2) cyclic loading with a lower frequency preceding higher frequency loading also prolongs the fatigue life. A creep crack hypothesis is proposed that can provide reasonable interpretations for these experimental results.

Sun, C. T.↗

Using in situ UO 2 bicrystal sintering to understand grain boundary dislocation nucleation kinetics and creep

Capillary evolution at bicrystal UO 2 grain boundaries is characterized using in situ transmission electron microscopy. The discontinuous nature of the densification process, both particle rotation and axial strain, along with the large activation stress for densification support a hypothesis that grain boundary strain in UO 2 follows nucleation rate limited kinetics at low to intermediate stresses, that is, less than ≈ 10 8 PA. Further, the temperature dependence of the average activation stress for sintering agrees well with analysis of bulk sintering data and creep data reported within the literature when analyzed in the context of a grain boundary dislocation nucleation rate limited kinetic model.

36 MATERIALS SCIENCE↗

Creep of Uncoated and Cu-Cr Coated NARloy-Z

Stress rupture creep tests were performed on uncoated and Cu-30vol%Cr coated NARloy-Z copper alloy specimens exposed to air at 482 C to 704 C. The results showed that creep failure in air of unprotected NARloy-Z was precipitated by brittle intergranular surface cracking produced by strain assisted grain boundary oxidation (SAGBO) which in turn caused early onset of tertiary creep. For the protected specimens, the Cu-Cr coating remained adherent throughout the tests and was effective in slowing down the rate of oxygen absorption, particularly at the higher temperatures, by formation of a continuous chromium oxide scale. As the result of reducing oxygen ingress, the coating prevented SAGBO initiated early creep failure, extended creep deformation and increased the creep rupture life of NARloy-Z over the entire 482 C to 704 C test temperature range.

Walter, R. J.↗

Reversible and Irreversible Time-Dependent Behavior of GRCop-84

A series of mechanical tests were conducted on a high-conductivity copper alloy, GRCop-84, in order to understand the time dependent response of this material. Tensile, creep, and stress relaxation tests were performed over a wide range of temperatures, strain rates, and stress levels to excite various amounts of time-dependent behavior. At low applied stresses the deformation behavior was found to be fully reversible. Above a certain stress, termed the viscoelastic threshold, irreversible deformation was observed. At these higher stresses the deformation was observed to be viscoplastic. Both reversible and irreversible regions contained time dependent deformation. These experimental data are documented to enable characterization of constitutive models to aid in design of high temperature components.

viscoelasticity↗

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗

Summary of Structural Alloy Compatibility in Supercritical CO2 at 450°-800°C

Supercritical CO2 (sCO2) is of interest as a working fluid for several concepts including the direct- fired Allam cycle as a low-emission fossil energy power cycle. Over the past 10 years, laboratory exposures at 300 bar sCO2 have found reasonably good compatibility for Ni-based alloys at <800°C, including an assessment of the sCO2 impact on room temperature mechanical properties after 750°C exposures. However, initial screening tests at 1 and 20 bar CO2 at 900°-1100°C showed poor compatibility for Ni-based alloys. In an open cycle, the introduction of 1%O2 and 0.1- 0.25%H2O impurities at 300 bar increased the reaction rates ≥2X at 750°C. At lower temperatures, steels are susceptible to C ingress and embrittlement. Creep-strength enhanced ferritic steels may be limited to <550°C and conventional stainless steels to <600°C. Two strategies to increase those temperatures are higher Ni and Cr alloying additions and Al- or Cr-rich coatings. Alloy 709 (Fe- 20Cr-25Ni) shows some promising results at 650°C in sCO2 but reaction rates were accelerated with the addition of O2 and H2O impurities. Pack aluminized and chromized Gr.91 (Fe-9Cr-1Mo) and type 316H stainless steel show some promise at 600°-650°C but further coating optimization is needed.

Pint, Bruce↗

Space Shuttle Orbiter engine main combustion chamber cooling and life

A reusable life requirement of 100 missions is met by controlling the combustion chamber hot-gas wall temperature and strain levels. Maximum life, maximum performance, and minimum engine weight are attained through a descriptive parametric assessment of the regenerative cooling circuit, combustor length, contraction area ratio, and coolant passage geometry. Life is categorized by low-cycle fatigue and creep-stress rupture. Relationships are developed to determine the impact of heat transfer rate, thermal strain level, and geometric influence parameters on life. It is empirically shown that a throat heat flux of 100 Btu/sq in./sec can be accommodated.

Cook, R. T.↗

Kinetic studies of the stress corrosion cracking of D6AC steel

The effect of load interactions on the crack growth velocity of D6AC steel under stress corrosion cracking conditions was determined. The environment was a 3.5 percent salt solution. The modified-wedge opening load specimens were fatigue precracked and subjected to a deadweight loading in creep machines. The effects of load shedding on incubation times and crack growth rates were measured using high-sensitivity compliance measurement techniques. Load shedding results in an incubation time, the length of which depends on the amount of load shed and the baseline stress intensity. The sequence of unloading the specimen also controls the subsequent incubation period. The incubation period is shorter when load shedding passes through zero load than when it does not if the specimen initially had the same baseline stress intensity. The crack growth rates following the incubation period are also different from the steady-state crack growth rate at the operating stress intensity. These data show that the susceptibility of this alloy system to stress corrosion cracking depends on the plane-strain fracture toughness and on the yield strength of the material.

Noronha, P. J.↗

An experimental study of biaxial yield in modified 9Cr-1Mo steel at room temperature

Described are two biaxial experiments which investigated yield, hardening, and flow behavior in modified 9Cr-1Mo steel at room temperature. The aim of these experiments was to determine whether the procedures recommended in NE Standard F9-5T for inelastic design analysis are applicable for this material in normalized and tempered condition. The first experiment investigated small offset yield behavior subsequent to radial preloads (sq rt of 3 sub sigma 12 = sub sigma 11) in tension-torsion stress space. The second experiment investigated yield behavior subsequent to nonradial preloads and also the time-dependent flow occurring during 0.5 hour periods at constant stress. The results of these experiments were qualitatively similar to those obtained earlier for types 304 and 316 stainless steel. Specifically, the von Mises yield criterion was found to provide a reasonable approximation of initial yield behavior. Although the subsequent yield surfaces suffered considerable distortion from their near-circular form after both radial and nonradial preloads, the hardening behavior was to the first order kinematic in nature. The strain-time data obtained during the 0.5 hr hold periods showed characteristics typical of creep curves. As in the case of earlier experiments, the high initial flow rates diminished more rapidly than would be estimated from elevated temperature data.

Ellis, J. R.↗

Viscoplastic Characterization of Ti-6-4: Experiments

As part of a continued effort to improve the understanding of material time-dependent response, a series of mechanical tests have been conducted on the titanium alloy, Ti-6Al-4V. Tensile, creep, and stress relaxation tests were performed over a wide range of temperatures and strain rates to engage various amounts of time-dependent behavior. Additional tests were conducted that involved loading steps, overloads, dwell periods, and block loading segments to characterize the interaction between plasticity and time-dependent behavior. These data will be used to characterize a recently developed, viscoelastoplastic constitutive model with a goal toward better estimates of aerospace component behavior, resulting in improved safety.

mechanical properties↗

Non-isothermal elastoviscoplastic snap-through and creep buckling of shallow arches

The problem of buckling of shallow arches under transient thermomechanical loads is investigated. The analysis is based on nonlinear geometric and constitutive relations, and is expressed in a rate form. The material constitutive equations are capable of reproducing all non-isothermal, elasto-viscoplastic characteristics. The solution scheme is capable of predicting response which includes pre and postbuckling with creep and plastic effects. The solution procedure is demonstrated through several examples which include both creep and snap-through behavior.

Simitses, G. J.↗

Computational thermomechanics for crystalline rock. Part II: Chemo-damage-plasticity and healing in strongly anisotropic polycrystals

We present a thermal–mechanical–chemical-phase field model that captures the multi-physical coupling effects of precipitation creeping, crystal plasticity, anisotropic fracture, and crack healing in polycrystalline rock at various temperature and strain-rate regimes. This model is solved via a fast Fourier transfer solver with an operator-split algorithm to update displacement, temperature and phase field, and chemical concentration incrementally. In nuclear waste disposal in salt formation, brine inside the crystal salt may migrate along the grain boundary and cracks due to the gradient of interfacial energy and pressure. This migration has a significant implication on the permeability evolution, creep deformation, and crack healing within rock salt but is difficult to incorporate implicitly via effective medium theories compared with computational homogenization. As such, we introduce a thermodynamic framework and a corresponding computational implementation that explicitly captures the brine diffusion along the grain boundary and crack at the grain scale. Meanwhile, the anisotropic fracture and healing are captured via a high-order phase field that represents the regularized crack region in which a newly derived non-monotonic driving force is used to capture the fracture and healing due to the solution–precipitation. Numerical examples are presented to demonstrate the capacity of the thermodynamic framework to capture the multiphysics material behaviors of rock salt.

42 ENGINEERING↗

A reinvestigation into Munson’s model for room closure in bedded rock salt

Accurate predictions of room closure are important for hazardous waste repositories in rock salt formations, such as the Waste Isolation Pilot Plant (WIPP). When Munson and co-workers simulated several room closure experiments conducted at the WIPP during the 1980’s and 1990’s, their simulated closure curves closely agreed with the closure measurements. A careful review of their work, however, raised concerns and prompted the reinvestigation in this paper. Here, to begin the reinvestigation, Munson’s legacy Room D closure simulation was reasonably recreated in a current-day finite element code. Next, special care was taken to obtain numerically converged results, re-introduce the anhydrite strata intermittently ignored by Munson, and calibrate the Munson–Dawson (M–D) constitutive model for salt as much as possible from laboratory test measurements. When this new model was used to simulate Room D’s closure, it under-predicted the horizontal and vertical closure rates by 2.34x and 3.10x, respectively, at 5.7 years after room excavation. As a result, the M–D model was extended to capture the newly established creep behavior at low equivalent stresses (<8 MPa) and replace the Tresca with the Hosford equivalent stress. Simulations using the new M–D model over-predicted the horizontal closure rate by 1.15x and under-predicted the vertical closure rate by 1.08x at 5.7 years, averaged over three room closure experiments. Although further improvements could be made, the new model has a stronger scientific foundation than Munson’s legacy model and appears ready for careful engineering use.

58 GEOSCIENCES↗

High temperature materials for space power systems

Future space power systems will largely be nuclear-driven or solar-driven Brayton cycle or thermionic converter systems. This paper presents some of the limited data available on the long-time properties of the superalloys and refractory metals that will have to be used in large parts of these systems. These data include vaporization rates of pure metals as a function of temperature, extrapolated stress for 1 percent creep in 10 years for selected superalloys, vacuum creep behavior of Mar M-509 at 900 C and 110 MN/sq m, extrapolated stress for 1 percent creep in 10 years for refractory alloys, and approximate useful temperature ranges for superalloys and refractory metals.

Gangler, J. J.↗

Constitutive modeling for isotropic materials

A state-of-the-art review of applicable constitutive models with selection of two for detailed comparison with a wide range of experimental tests was conducted. The experimental matrix contained uniaxial and biaxial tensile, creep, stress relaxation, and cyclic fatigue tests at temperatures to 1093 C and strain rates from .0000001 to .001/sec. Some nonisothermal cycles will also be run. The constitutive models will be incorporated into the MARC finite element structural analysis program with a demonstration computation made for advanced turbine blade configuration. In the code development work, particular emphasis is being placed on developing efficient integration algorithms for the highly nonlinear and stiff constitutive equations. Another area of emphasis is the appropriate and efficient methodology for determing constitutive constants from a minimum extent of experimental data.

Lindholm, U. S.↗

Modeling surface deformations at complex strike-slip plate boundaries

Two new versions of the physical base-traction model of Li and Rice (1987) have been developed to study the loading processes and surface deformation near plate boundaries with geometric complexities, including a shallow creeping fault segment and two subparallel faults. Predictions of surface velocity and surface slip rate for the region between the San Andreas fault and the Pacific coast at the latitude of the Parkfield-Cholame segment using model parameters based on geologic, geodetic, and seismic considerations were found to be in good agreement with contemporary geodetic field data (not used in constrainning model parameters). Also, predicted surface velocity for the Salton Sea-Coachella Valley area were fit to recently derived contemporary geodetic data and very large baseline interferometry data, althoug here the model parameters are not well constrained.

Li, Victor C.↗

The constitutive representation of high-temperature creep damage

The elastic-viscoplastic constitutive equations of Bodner-Partom were applied to modeling creep damage in a high temperature Ni-alloy, B1900 + Hf. Both tertiary creep in bulk materials and creep crack growth in flawed materials were considered. In the latter case, the energy rate line integral was used for characterizing the crack driving force, and the rate of crack extension was computed using a local damage formulation that assumed fracture was controlled by cavitation occurring within the crack-tip process zone. The results of this investigation were used to assess the evolution equation for isotropic damage utilized in the Bodner-Partom constitutive equations.

Chan, K. S.↗