Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diameter effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Effects of film injection on performance of a cooled turbine

Tests were conducted in a 20 inch diameter single stage air cooled turbine designed to evaluate the effects of film cooling air on turbine aerodynamic performance. A comparison was made of the experimental results and an analytical method of evaluating film injection effects on turbine performance. The results are used to determine the effects of film cooling on overall engine performance for selected cycle conditions. The engine performance studies are used to show the cycle benefits of increased gas temperature at various coolant flow rates.

Mcdonel, J. D.↗

Results of acoustic tests of a Prop-Fan model

Results of acoustic tests in a low speed open jet anechoic wind tunnel are presented for a counter rotation Prop-Fan model. The model tested had 5 front and 5 rear rotor blades with swept planform. Noise spectra are presented showing the influence of operating and configuration variables such as: (1) power absorption, (2) tip speed, (3) rotor-rotor spacing, (4) power split between the front and rear blade rows, (5) variation of the RPM ratio between front and rear blade rows, (6) tractor versus pusher (pylon effects), and (7) angle of attack. In addition to model scale results, calculated levels derived from test are presented showing the influence of the above variables on Effective Perceived Noise Level of a 13.1 ft diameter Prop-Fan at a flyover distance of 1500 ft. It was found that the strongest effects are caused by tip speed and power absorption. A significant finding was that there is an optimum operating tip speed for minimum noise for a given power absorption. Effects of other parametric variations are generally small but measurable. In order to minimize noise to meet airplane certification limits, operation at moderate tip speeds and power absorption is shown to be desirable. Accuracy of predicted Effective Perceived Noise Level is shown to be good with the best accuracy in the 590 to 670 ft/sec tip speed range.

Metzger, F.B.↗

An atmosphere on Ganymede from its occultation of SAO 186800 on 7 June 1972.

The observational data obtained during the occultation are of sufficient quality to determine the occultation radius and to support the inference that Ganymede does possess at least a modest atmosphere. Assuming a circular cross section, the diameter of Ganymede was found to be 5271 km. Effects of the atmosphere on the accuracy of the value obtained for the Ganymede diameter are discussed.

Carlson, R. W.↗

A wind tunnel investigation of circular and straked cylinders in transonic cross flow

Pressure distributions around circular and circular/strake cylinders were measured in a wind tunnel at Mach numbers from 0.6 to 1.2 with Reynolds number independently variable from 10,000 to 100,000. The local pressures are integrated over the cylinder surface to determine the variation of drag coefficient with both Mach number and Reynolds number. Effects of tunnel blockage are evaluated by comparing results from circular cylinders of various diameters at common Mach and Reynolds number conditions. Compressibility effects are concluded to be responsible for a flight reduction of the drag coefficient near Mach 0.7. Drag increases with strake height, presumably approaching a maximum drag corresponding to a flat plate configuration.

Macha, J.↗

COMPASS-FME Terrestrial Ecosystem Manipulation to Probe the Effects of Storm Treatments (TEMPEST) Experiment Tree Inventory

This is the tree inventory (diameter, species, and live/dead status) data from the Terrestrial Ecosystem Manipulation to Probe the Effects of Storm Treatments (TEMPEST) experimental site. This manipulative, ecosystem-scale TEMPEST experiment is part of the COMPASS-FME (Coastal Observations, Mechanisms, and Predictions Across Systems and Scales: Field Measurements and Experiments; see https://compass.pnnl.gov/FME/COMPASSFME) project. It addresses the potential for freshwater and estuarine-water disturbance events to alter tree function, species composition, and ecosystem processes in a deciduous coastal forest in eastern Maryland, USA. The experiment uses a large-unit (2000 m2), un-replicated experimental design, with three 50 m × 40 m plots serving as control, freshwater, and estuarine-water treatments.This dataset includes:- An overall dataset README file.- The tree inventory data in both "wide" and "long" forms. These contain the same information but are structured differently, with the former more useful for human viewers and the latter more amenable for programmatic analyses.- A key to the species/genus codes used, which follow the U.S. Department of Agriculture's PLANTS schema (https://plants.usda.gov/).- A copy of the R code used to generate the wide- and long-form data files.All files are comma-separated value (CSV) and no special software is required to read them.

54 ENVIRONMENTAL SCIENCES↗

Estimating the Concentration of Large Raindrops from Polarimetric Radar and Disdrometer Observations

Estimation of rainfall integral parameters, including radar observables, and empirical relations between them are sensitive to the truncation of the drop size distribution (DSD), particularly at the large drop end. The sensitivity of rainfall integral parameters to the maximum drop diameter (D(sub max)) is exacerbated at C‐band since resonance effects are pronounced for large drops in excess of 5 mm diameter (D). Due to sampling limitations, it is often difficult to reliably estimate D(sub max) with disdrometers. The resulting uncertainties in D(sub max0 potentially increase errors in radar retrieval methods, particularly at C‐band, that rely on disdrometer observations for DSD input to radar models. In fact, D(sub max) is typically an assumed DSD parameter in the development of radar retrieval methods. Because of these very uncertainties, it is difficult to independently confirm disdrometer estimates of D(sub max) with polarimetric radar observations. A couple of approaches can be taken to reduce uncertainty in large drop measurement. Longer integration times can be used for the collection of larger disdrometer samples. However, integration periods must be consistent with a radar resolution volume (RRV) and the temporal and spatial scales of the physical processes affecting the DSD therein. Multiple co‐located disdrometers can be combined into a network to increase the sample size within a RRV. However, over a reasonable integration period, a single disdrometer sample volume is many orders of magnitudes less than a RRV so it is not practical to devise a network of disdrometers that has an equivalent volume to a typical RRV. Since knowledge of DSD heterogeneity and large drop occurrence in time and space is lacking, the specific accuracy or even general representativeness of disdrometer based D(sub max) and large drop concentration estimates within a RRV are currently unknown. To address this complex issue, we begin with a simpler question. Is the frequency of occurrence of large rain drops (D > 5 mm) in disdrometer observations, either stand alone or networked, generally representative and consistent with polarimetric radar observations? We first show from simulations that the concentration of large (D > 5 mm) rain drops (N(sub T5)) can be estimated from polarimetric observations of specific differential phase (K(sub dp)) and differential reflectivity (Z(sub dr)), N(sub T5)=F(K(sub dp),Z(sub dr)), or horizontal reflectivity (Z(sub h)) and Z(sub dr), N(sub T5)=(Z(sub h),Z(sub dr)). We assess the error associated with polarimetric retrieval of N(sub T5), including sensitivity to D(sub max) parameterization assumptions and measurement error in the radar simulations. Polarimetric measurements at S‐band and C‐band will then be used to retrieve estimates of N(sub T5) and compared to disdrometer estimates of N(sub T5). After careful consideration of retrieval error, we will check consistency between disdrometer and polarimetric radar estimates of N(sub T5) and the frequency of occurrence of large rain drops in a variety of precipitating regimes using data from NASA's Global Precipitation Measurement (GPM) Ground Validation (GV) program, including field campaigns such as MC3E (Oklahoma) and IFloodS (Iowa) and extended measurements over Huntsville, Alabama and NASA Wallops Flight Facility in coastal Virginia.

Carey, Lawrence D.↗

Aerodynamic Characteristics of Towed Cones Used as Decelerators at Mach Numbers from 1.57 to 4.65

Towed and sting-supported cones were tested in the wake of various payloads at supersonic speeds to determine their drag and stability characteristics. The investigation extended over a Mach number range from 1.57 to 4.65 and included such variables as Reynolds number, cone angle, ratio of cone base diameter to payload base diameter, and trailing distance. The results of this investigation showed that the cones towed in the wake of a symmetrical payload at supersonic speeds, in general, have good drag and stability characteristics if towed in the supersonic flow region. A cone with an included angle between 80 deg and 90 deg will give maximum drag while still maintaining stability in the Mach number region of this investigation. In order to minimize wake effects, the ratio of cone base diameter to payload base diameter should be at least one and preferably around three. A trailing distance of three times the payload base diameter, in most cases, is of sufficient length to avoid low drag and instability of the decelerator.

Charczenko, Nickolai↗

Ancient fluvial processes in the equatorial highlands of Mars

Martian highland craters typically lack ejecta deposits, have no noticeable rim, and are flat floored. In addition, crater size frequency distribution curves show that highland craters have depleted populations less than 20 km in diameter. A variety of processes have been suggested to explain these observations including deposition of aeolian or volcanic materials up to the crater rim crests, thermal creep, terrain softening, and mass wasting. However, none of these processes adequately explains both the crater morphology and population distribution. In order to explain both the Martian highland crater morphology and population distribution, a fluvial process is proposed which is capable of removing the loose crater rim material. The resulting effect is to decrease the crater diameter, thereby causing the population curves to bendover. The eroded material is redistributed, burying or partially burying smaller diameter craters before complete erosion. This material may also be deposited into local topographic lows, creating the depositional basins observed. A fluvial process explains both sets of observations: crater morphology and crater population distribution curves.

Craddock, Robert A.↗

Patterned dielectric back contact design for GaAs thermophotovoltaic devices

-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.

14 SOLAR ENERGY↗

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗

Effects of interstage diffuser flow distortion on the performance of a 15.41-centimeter tip diameter axial power turbine

The performance of a variable-area stator, axial flow power turbine was determined in a cold-air component research rig for two inlet duct configurations. The two ducts were an interstage diffuser duct and an accelerated-flow inlet duct which produced stator inlet boundary layer flow blockages of 11 percent and 3 percent, respectively. Turbine blade total efficiency at design point was measured to be 5.3 percent greater with the accelerated-flow inlet duct installed due to the reduction in inlet blockage. Blade component measurements show that of this performance improvement, 35 percent occurred in the stator and 65 percent occurred in the rotor. Analysis of inlet duct internal flow using an Axisymmetric Diffuser Duct Code (ADD Code) were in substantial agreement with the test data.

Mclallin, K. L.↗

D-Egg: a dual PMT optical module for IceCube

The D-Egg, an acronym for "Dual optical sensors in an Ellipsoid Glass for Gen2," is one of the optical modules designed for future extensions of the IceCube experiment at the South Pole. The D-Egg has an elongated-sphere shape to maximize the photon-sensitive effective area while maintaining a narrow diameter to reduce the cost and the time needed for drilling of the deployment holes in the glacial ice for the optical modules at depths up to 2700 m. The D-Egg design is utilized for the IceCube Upgrade, the next stage of the IceCube project also known as IceCube-Gen2 Phase 1, where nearly half of the optical sensors to be deployed are D-Eggs. With two 8-inch high-quantum efficiency photomultiplier tubes (PMTs) per module, D-Eggs offer an increased effective area while retaining the successful design of the IceCube digital optical module (DOM). The convolution of the wavelength-dependent effective area and the Cherenkov emission spectrum provides an effective photodetection sensitivity that is 2.8 times larger than that of IceCube DOMs. The signal of each of the two PMTs is digitized using ultra-low-power 14-bit analog-to-digital converters with a sampling frequency of 240 MSPS, enabling a flexible event triggering, as well as seamless and lossless event recording of single-photon signals to multi-photons exceeding 200 photoelectrons within 10 ns. Mass production of D-Eggs has been completed, with 277 out of the 310 D-Eggs produced to be used in the IceCube Upgrade. In this paper, we report the design of the D-Eggs, as well as the sensitivity and the single to multi-photon detection performance of mass-produced D-Eggs measured in a laboratory using the built-in data acquisition system in each D-Egg optical sensor module.

47 OTHER INSTRUMENTATION↗

Herbicide, fertilization, and planting density effects on intensively managed loblolly pine early stand development

Production forestry in the southeast US has been partially transitioned to intensively managed short rotations (~10 years), in which multiple silvicultural interventions are performed during forest development. Understanding the responses to silvicultural practices and continued refinement of site-specific recommendations is critical to sustainably maximize forest production. We evaluated the effects of silvicultural practices (herbicide, fertilization, and planting density) on growth, stand homogeneity, and above- and belowground biomass accumulation and partitioning of loblolly pine (Pinus taeda) throughout early stand development (age 5 years) in the southeastern US. Five treatments with eight replications each were tested: no herbicide and no fertilization (C); herbicide only (H); herbicide and half-reduced fertilization rate (R); herbicide and full fertilization (F); and increased stand density (60+ %; 1346 vs. 2152 trees per hectare) with herbicide and full fertilization rate (D). Allometric equations generated from destructive harvests were applied to annual diameter measurements to estimate plot-level biomass and allocation. Herbicide was crucial to promote stand uniformity and increase yield (~600+ % stem biomass compared with C at age 5). Aboveground biomass was similar in R and F treatments, which was ~25% higher than in H at age 5. Increasing planting density along with multiple herbicide and fertilizer applications yielded higher biomass without compromising individual tree size (diameter and height). There was little effect of silviculture practices on allocation patterns. Our results parallel what was found for fertilization with herbicide from a number of loblolly stands under similar conditions and indicate a ~28% volume gain with fertilization during early stand development. Similarly, our results were consistent with other studies implementing similar differences in planting density and suggest a ~26% volume gain through early stand development with an initial 60% increase in planting density. Furthermore, our study helps to understand complex relationships between production and silvicultural practices during early stand development and demonstrates that silvicultural prescriptions can be optimized to increase sustainability of production forestry

59 BASIC BIOLOGICAL SCIENCES↗

Synthesis of Narrow SnTe Nanowires Using Alloy Nanoparticles

Topological crystalline insulator tin telluride (SnTe) provides a rich playground to examine interactions of correlated electronic states, such as ferroelectricity, topological surface states, and superconductivity. The study of SnTe nanowires may lead to even richer physics owing to the one-dimensional (1D) confinement effect and an increased contribution from the topological surface states. Thus, for transport measurements, SnTe nanowires must be synthesized with reduced diameters and high crystalline quality to ensure 1D confinement and phase coherence of the topological surface electrons. Here, we report a facile growth method to produce narrow SnTe nanowires with a high yield using alloy nanoparticles as growth catalysts. The average diameter of the SnTe nanowires grown using alloy nanoparticles is 85 nm, nearly a factor of three reduction compared to the average diameter of 240 nm when using gold nanoparticles as growth catalysts. Transport measurements reveal the effect of the nanowire diameter on the residual resistance ratio and magnetoresistance. Particularly, the ferroelectric transition temperature for SnTe evolves systematically with the nanowire diameter. In situ cryogenic cooling of narrow SnTe nanowires in a transmission electron microscope directly reveals the cubic to rhombohedral structural transition, which is associated with the ferroelectric transition. Thus, these narrow SnTe nanowires represent a model system to study electronic states arising from 1D confinement, such as 1D topological superconductivity and potential multiband superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advanced space propulsion thruster research

Experiments showed that stray magnetic fields can adversely affect the capacity of a hollow cathode neutralizer to couple to an ion beam. Magnetic field strength at the neutralizer cathode orifice is a crucial factor influencing the coupling voltage. The effects of electrostatic accelerator grid aperture diameters on the ion current extraction capabilities were examined experimentally to describe the divergence, deflection, and current extraction capabilities of grids with the screen and accelerator apertures displaced relative to one another. Experiments performed in orificed, mercury hollow cathodes support the model of field enhanced thermionic electron mission from cathode inserts. Tests supported the validity of a thermal model of the cathode insert. A theoretical justification of a Saha equation model relating cathode plasma properties is presented. Experiments suggest that ion loss rates to discharge chamber walls can be controlled. A series of new discharge chamber magnetic field configurations were generated in the flexible magnetic field thruster and their effect on performance was examined. A technique used in the thruster to measure ion currents to discharge chamber walls is described. Using these ion currents the fraction of ions produced that are extracted from the discharge chamber and the energy cost of plasma ions are computed.

Wilbur, P. J.↗

Thermal Infrared Hot Spot and Dependence on Canopy Geometry

We perform theoretical calculations of the canopy thermal infrared (TIR) hot spot using a first principles 3-D model described earlier. Various theoretical canopies of varying leaf size and for differing canopy height are used to illustrate the magnitude of the TIR effect. Our results are similar to predicted behavior in the reflective hot spot as a function of canopy geometry and comparable to TIR measurements from the literature and our own simple ground experiments. We apply the MODTRAN atmospheric code to estimate the at-sensor variation in brightness temperature with view direction in the solar principal plane. For simple homogeneous canopies, we predict canopy thermal infrared hot spot variations of 2 degrees C at the surface with respect to nadir viewing. Dependence on leaf size is weak as long as the ratio of leaf size to canopy height is maintained. However, the angular width of the hot spot increases as the ratio of leaf diameter to canopy height increases. Atmospheric effects minimize but do not eliminate the TIR hot spot at satellite altitudes.

Smith, James A.↗

Approach to Analyzing VTR Core Performance Sensitivities to Fuel Manufacturing Uncertainties and Application to Fuel Slug Diameter

This report documents the initial effort to characterize sensitivity of VTR core performance to fuel manufacturing uncertainties. The effects of variation in the as-fabricated fuel slug diameter on VTR neutronics performance are evaluated, using both high-fidelity Monte Carlo (OpenMC) and the main core design solver (DIF3D) for all cases. This work and follow-on work will inform the VTR Project’s fuel manufacturing processes and associated acceptable criteria, as well as detailed uncertainty analysis in later stages of VTR development and deployment. In addition, this work demonstrates the approach to performing such evaluations and provides a basis for reducing the scope of calculations in future sensitivity analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loadings: Hamilton Standard 6507A-2 Four- and Three-Blade Propellers - 6

An altitude-wind-tunnel investigation has been made to determine the performance of Hamilton Standard 6507A-2 four-blade and three-blade propellers on a YP-47M airplane at high blade loadings and high engine powers. Characteristics of the four-blase propeller were obtained for a range of power coefficients from 0.10 to 1.00 at free-stream Mach numbers of 0.20, 0.30, 0.40. Characteristics of the three-blade propeller were obtained for a range of power coefficients from 0.30 to 1.00 at a free-stream Mach number of 0.40. Results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio because no corrections for the effects of tunnel-wall constriction on the installation were applied. Slipstream surveys are presented to illustrate blade thrust load distribution for certain operating conditions. Within the range of advance-diameter ratios investigated at each free-stream Mach number, the efficiency of the four-blade propeller decreased as the power coefficient was increased from 0.10 to 1.00. For the three-blade propeller, nearly constant maximum efficiencies were obtained for power coefficients from 0.32 to 0.63 at advance-diameter ratios between 1.90 and 3.00. In general, for conditions below the stall and critical tip Mach number, the maximum thrust load shifted from the inboard sections toward the tip sections as the power coefficient was increased or as the advance-diameter ratio was decreased. For conditions beyond the stall or critical tip Mach number, losses in thrust occurred on the outboard blade sections owing to flow break-down; the thrust load increased slightly on the inboard sections.

Saari, Martin J.↗