Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distributed temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Program to develop a performance and heat load prediction system for multistage turbines

Flows in low-aspect ratio turbines, such as the SSME fuel turbine, are three dimensional and highly unsteady due to the relative motion of adjacent airfoil rows and the circumferential and spanwise gradients in total pressure and temperature, The systems used to design these machines, however, are based on the assumption that the flow is steady. The codes utilized in these design systems are calibrated against turbine rig and engine data through the use of empirical correlations and experience factors. For high aspect ratio turbines, these codes yield reasonably accurate estimates of flow and temperature distributions. However, future design trends will see lower aspect ratio (reduced number of parts) and higher inlet temperature which will result in increased three dimensionality and flow unsteadiness in turbines. Analysis of recently acquired data indicate that temperature streaks and secondary flows generated in combustors and up-stream airfoils can have a large impact on the time-averaged temperature and angle distributions in downstream airfoil rows.

Sharma, OM↗
NASA NTRS1993

Large-scale coronal temperature and density distributions, 1984-1992

We characterize the temperature and the density structure of the corona utilizing spectrophotometric observations at different heights but at the same latitude during the descending phase of cycle 21 through the ascending phase of cycle 22. The data include ground-based intensity observations of the green (Fe XIV 5303) and red (Fe X 6374) coronal forbidden lines, photospheric magnetographs from the National Solar Observatory, Kitt Peak, and synoptic maps of white-light K-coronal polarized brightness from the High Altitude Observatory. A determination of plasma temperature, T, can be estimated from the intensity ratio Fe X/Fe XIV (where T is inversely proportional to the ratio), since both emission lines come from ionized states of Fe, and the ratio is only weakly dependent on density. Distributions of the electron temperature from the line ratio and the polarized brightness which yields electron density of the corona during the descending and the ascending phases of solar cycles 21 and 22 are presented. These data refer to structures of the corona which are relatively large scale, having a temporal coherence of at least two or more synoptic rotation periods, such as the streamer belts, the individual helmet streamers, and the larger coronal holes.

Guhathakurta, M.↗
NASA NTRS1994

Experimental Investigation of Solid Rod Cathode Operation

A series of models have been developed to describe the temperature distribution of thermionic cathodes in high current discharges in an effort to evaluate cathode service life. A number of experimental measures have been made to validate these models and provide values of the input parameters. Examination of the surfaces of several cathodes after varying lengths of operation shows the evolution of surface microstructures and reveals the preferential deposition of thorium metal on the cathode tip.

thermionic↗
NASA NTRS1980

The distribution of maximum temperatures of coronal active region loops

The emission measure distribution across the range 4.5 log T 6.5 was derived for several coronal active regions by combining EUV line fluxes with broadband X-ray fluxes. The distributions of the maximum temperature was then derived using a numerical model. It is shown that the emission measure distribution can be represented over the full range 5.6 log Tm 6.5 by the superposition of simple loop models, if the models incorporate a substantial rise in their individual emission measure distributions near the maximum temperature. The unresolved loops may have substantial area ratios, since it is this ratio that fixes the extent of the rise in the emission measure distribution. Since the bulk of the emission measure is then contributed from the loop tops, the distribution of maximum temperatures has approximately the same shape as does the integrated emission measure distributions. The EUV and X-ray data used were obtained by from two separate experiments on ATM/Skylab.

Mayfield, E. B.↗
NASA NTRS1993

Refractive Index and Scattering Effects on Radiative Behavior of a Semitransparent Layer

Heat transfer characteristics are analyzed for a plane layer of semitransparent material with refractive index not less than 1. Energy transfer in the material is by conduction, emission, absorption, and isotropic scattering. Each side of the layer is heated by radiation and convection. For a refractive index larger than unity, there is internal reflection of some of the energy within the layer. This, coupled with scattering, has a substantial effect on distributing energy across the layer and altering the temperature distribution from when the refractive index is unity. The effect of scattering is examined by comparisons with results from an earlier paper for an absorbing layer. Results are given for a gray medium with a scattering albedo up to 0.999, and for a two-band spectral variation of the albedo with one band having low absorption. Radiant energy leaving the surface as a result of emission and scattering was examined to determine if it could be used to accurately indicate the surface temperature.

Spuckler, C. M.↗
NASA NTRS1975

NIMBUS-5 sounder data processing system. Part 2: Results

The Nimbus-5 spacecraft carries infrared and microwave radiometers for sensing the temperature distribution of the atmosphere. Methods developed for obtaining temperature profiles from the combined set of infrared and microwave radiation measurements are described. Algorithms used to determine (a) vertical temperature and water vapor profiles, (b) cloud height, fractional coverage, and liquid water content, (c) surface temperature, and (d) total outgoing longwave radiation flux are described. Various meteorological results obtained from the application of the Nimbus-5 sounding data processing system during 1973 and 1974 are presented.

Smith, W. L.↗
NASA NTRS1980

Scientific objectives of the Solar Mesosphere Explorer mission

The paper describes the NASA Solar Mesosphere Explorer mission which will study mesospheric ozone and the processes which form and destroy it, measure the ozone density and its altitude distribution from 30 to 80 km, monitor incoming solar UV radiation, and provide a rigorous test of the photochemical equilibrium theory of the mesospheric oxygen-hydrogen system. Five instruments will be carried on the polar-orbiting spacecraft: UV ozone, IR airglow, and visible NO2 programmable Ebert-Fastie spectrometers, a four-channel IR radiometer, and a solar UV spectrometer. Atmospheric measurements will be made of the mesospheric and stratospheric ozone density distribution, water vapor density distribution, temperature profile, ozone photolysis rate, and NO2 density distribution. In addition, the solar UV monitor will measure both the 0.2-0.31 micron spectral region and the Lyman-alpha (0.1216 micron) contribution to the solar irradiance.

Thomas, G. E.↗
NASA NTRS1980

Ion temperature troughs induced by a meridional neutral air wind in the night-time equatorial topside ionosphere

A mathematical model was constructed to calculate O(+) and H(+) concentrations, field-aligned velocities, and electron temperatures in the night-time equatorial topside ionosphere. The model is used to establish the ability of F-region neutral air winds to produce observed ion temperature distributions, and to study the properties of ion temperature troughs as functions of altitude, latitude, and ionospheric composition. The O(+) - H (+) transition height represents an altitude limit above which the ion cooling from adiabatic expansion of the plasma is very small; the northern and southern edges of the ion temperature troughs are restricted to the limiting dip altitudes determined by magnetic field line geometry and by the functional form of the F-region neutral wind velocity.

Bailey, G. J.↗
NASA NTRS1987

Status of holographic interferometry at University of Michigan

Reflection holograms were taken of a jet of air injected traverse to a subsonic stream. The technique of reflection holograms allowed maximum viewing angle and minimum distance to the jet. Holographic interferometry is being used to measure the temperature distribution in a growing crystal. Computations of the temperatures are being made. A phase shift interferometer was used to study flows with very weak changes in refractive index, of the order of 1 shift. Tomographic techniques are being developed for strong refractive cases.

Vest, Charles↗
NASA NTRS1987

Microgravity nucleation and particle coagulation experiments support

A hollow sphere model is developed to predict the range of supersaturation ratio values for refractory metal vapors in a proposed experimental nucleation apparatus. Since the experiments are to be carried out in a microgravity environment, the model neglects the effects of convection and assumes that the only transfer of vapors through an inert gas atmosphere is by conduction and molecular diffusion. A consistent set of physical properties data is assembled for the various candidate metals and inert ambient gases expected to be used in the nucleation experiments. Transient partial pressure profiles are computed for the diffusing refractory species for two possible temperature distributions. The supersaturation ratio values from both candidate temperature profiles are compared with previously obtained experimetnal data on a silver-hydrogen system. The model is used to simulate the diffusion of magnesium vapor through argon and other inert gas atmospheres over ranges of initial and boundary conditions. These results identify different combinations of design and operating parameters which are liekly to produce supersaturation ratio values high enough to induce homogeneous nucleation in the apparatus being designed for the microgravity nucleation experiments.

Lilleleht, L. U.↗
NASA NTRS1993

Vibration analysis of heated anisotropic plates with free edge conditions

Tabular and plotted results are presented (as a function of lamination angle and temperature) for the first two vibration frequencies and mode shapes of a heated, single-layer Boron/epoxy laminate. A Ritz formulation is used to determine the thermally induced in-plane forces and the out-of-plane vibration frequencies. This approach is formulated in terms of the out-of-plane displacement and the in-plane stress function; both the displacement and the stress function are expressed as simple algebraic polynomials modified to satisfy the essential boundary conditions. Heating is applied as a steady-state temperature distribution; material properties are considered to be temperature-dependent. To establish the correctness and effectiveness of the method, the in-plane forces are compared with Fourier series analytical results.

Locke, James E.↗
NASA NTRS1947

Cooling of Gas Turbines I - Effects of Addition of Fins to Blade Tips and Rotor, Admission of Cooling Air Through Part of Nozzles, and Change in Thermal Conductivity of Turbine Components

An analysis was developed for calculating the radial temperature distribution in a gas turbine with only the temperatures of the gas and the cooling air and the surface heat-transfer coefficient known. This analysis was applied to determine the temperatures of a complete wheel of a conventional single-stage impulse exhaust-gas turbine. The temperatures were first calculated for the case of the turbine operating at design conditions of speed, gas flow, etc. and with only the customary cooling arising from exposure of the outer blade flange and one face of the rotor to the air. Calculations were next made for the case of fins applied to the outer blade flange and the rotor. Finally the effects of using part of the nozzles (from 0 to 40 percent) for supplying cooling air and the effects of varying the metal thermal conductivity from 12 to 260 Btu per hour per foot per degree Farenheit on the wheel temperatures were determined. The gas temperatures at the nozzle box used in the calculations ranged from 1600F to 2000F. The results showed that if more than a few hundred degrees of cooling of turbine blades are required other means than indirect cooling with fins on the rotor and outer blade flange would be necessary. The amount of cooling indicated for the type of finning used could produce some improvement in efficiency and a large increase in durability of the wheel. The results also showed that if a large difference is to exist between the effective temperature of the exhaust gas and that of the blade material, as must be the case with present turbine materials and the high exhaust-gas temperatures desired (2000F and above), two alternatives are suggested: (a) If metal with a thermal conductivity comparable with copper is used, then the blade temperature can be reduced by strong cooling at both the blade tip and root. The center of the blade will be less than 2000F hotter than the ends; (b) With low conductivity materials some method of direct cooling other than partial admission of cooling air is essential. From this study, it can be deduced that indirect cooling of turbine blades will not make possible large increases in gas temperature.

Brown, Byron↗
NASA NTRS2011

VLA Ammonia Observations of IRAS 16253-2429: A Very Young and Low Mass Protostellar System

IRAS l6253-2429. the source of the Wasp-Waist Nebula seen in Spitzer IRAC images, is an isolated very low luminosity ("VeLLO") Class 0 protostar in the nearby rho Ophiuchi cloud. We present VLA ammonia mapping observations of the dense gas envelope feeding the central core accreting system. We find a flattened envelope perpendicular to the outflow axis, and gas cavities that appear to cradle the outflow lobes as though carved out by the flow and associated (apparently precessing) jet. Based on the NH3 (1,1) and (2,2) emission distribution, we derive the mass, velocity fields and temperature distribution for the envelope. We discuss the combined evidence for this source as possibly one of the youngest and lowest mass sources in formation yet known.

Wiseman, Jennifer J.↗
NASA NTRS2011

Extremely Low Mass: The Circumstellar Envelope of a Potential Proto-Brown Dwarf

What is the environment for planet formation around extremely low mass stars? Is the environment around brown dwarfs and extremely low mass stars conducive and sufficiently massive for planet production? The determining conditions may be set very early in the process of the host object's formation. IRAS 16253-2429, the source of the Wasp-Waist Nebula seen in Spitzer IRAC images, is an isolated, very low luminosity ("VeLLO") Class 0 protostar in the nearby rho Ophiuchi cloud. We present VLA ammonia mapping observations of the dense gas envelope feeding the central core accreting system. We find a flattened envelope perpendicular to the outflow axis, and gas cavities that appear to cradle the outflow lobes as though carved out by the flow and associated (apparently precessing) jet, indicating environmental disruption. Based on the NH3 (1,1) and (2,2) emission distribution, we derive the mass, velocity fields and temperature distribution for the envelope. We discuss the combined evidence for this source to be one of the youngest and lowest mass sources in formation yet known, and discuss the ramifications for planet formation potential in this extremely low mass system.

Wiseman, Jennifer↗
NASA NTRS2016

Modeling Droplet Heat and Mass Transfer during Spray Bar Pressure Control of the Multipurpose Hydrogen Test Bed (MHTB) Tank in Normal Gravity

A CFD model for simulating pressure control in cryogenic storage tanks through the injection of a subcooled liquid into the ullage is presented and applied to the 1g MHTB spray bar cooling experiments. An Eulerian-Lagrangian approach is utilized to track the spray droplets and capture the interaction between the discrete droplets and the continuous ullage phase. The spray model is coupled with the VOF model by performing particle tracking in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. A new model for calculating the droplet-ullage heat and mass transfer is developed. In this model, a droplet is allowed to warm up to the saturation temperature corresponding to the ullage vapor pressure, after which it evaporates while remaining at the saturation temperature. The droplet model is validated against the results of the MHTB spray-bar cooling experiments with 50% and 90% tank fill ratios. The predictions of the present T-sat based model are compared with those of a previously developed kinetic-based droplet mass transfer model. The predictions of the two models regarding the evolving tank pressure and temperature distributions, as well as the droplets' trajectories and temperatures, are examined and compared in detail. Finally, the ullage pressure and local vapor and liquid temperature evolutions are validated against the corresponding data provided by the MHTB spray bar mixing experiment.

mass transfer↗
NASA NTRSDate not supplied

Comparison of Convective Heat Transfer Correlations and Their Application to NTP Reactors

This study analyzes various Nusselt number and friction factor correlations and applies them to a Small Nuclear Rocket Engine model with a Sinusoidal power distribution profile to understand their effects on the temperatures and pressures inside the reactor. A nodal thermal hydraulic solver was used to determine the fluid and channel surface temperatures while also incorporating variable fluid properties and channel roughness. The results showed that the considered friction factors could essentially be used interchangeably given that their difference affected the pressure by less than 1%. However, large variations in the tube surface temperature were obtained for the different Nusselt numbers while the fluid temperature distribution was forced to remain the same. Supersonic flow conditions presented by Maynard Taylor are investigated to serve as a baseline for how experimental errors can lead to uncertainties in the reported empirical correlations. Detailed experimental investigation is necessary to determine the Nusselt number correlation that will provide the best prediction of the thermal hydraulic performance inside the reactor fluid flow channels.

Nuclear Thermal Propulsion↗
NASA NTRS1986

Temperature fluctuations and infrared emission from dust particles in a hot gas

In this paper, the effect of temperature fluctuations in very small dust particles caused by electronic collisions with an ambient hot gas, is calculated. The dust-temperature distribution differs strongly from that derived on the basis of equilibrium heating models, peaking at lower temperatures in the stochastically heated case. The resulting infrared spectrum is broadened at short wavelengths, giving much more emission than expected from equilibrium calculations, and at long wavelengths exhibits a lower color temperature. Dust-temperature fluctuations are thus expected to play an important role in determining the infrared spectrum of dusty, X-ray-emitting plasmas. A power-law distribution of grain radii extended to very small grain sizes will have a distinct infrared spectrum characterized by an infrared excess at the Wien side of the spectrum. This excess emission represents a high-temperature component in the spectrum, resulting from the stochastic heating of very small dust particles. Its magnitude depends on the grain-size distribution and the temperature and density of the ambient hot gas. This excess emission may be observed by IRAS in supernova remnants and rich clusters of galaxies.

Dwek, E.↗