Results for “Elastic modulus” — Page 24

NASA NTRS1981

Some observations in high pressure rheology of lubricants

Experimental data are presented on viscosity, elastic shear modulus, and limiting shear stress of 12 liquid lubricants. It is shown that transition histories do affect the limiting shear stress of the materials in the form of isothermal compression resulting in a lower density and lower limiting stress than isobaric cooling. The measured limiting shear stress agrees with EHD traction data at slide-to-roll ratios of 0.1 or more. In pressure viscosity measurements of the polymer solutions, it is found that for some temperatures, the pressure viscosity coefficient of the blend is slightly less than that of the base, which results in the crossing of the viscosity-pressure isotherms at high pressures.

Bair, S.↗

NASA NTRS1983

Traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed.

Loewenthal, S. H.↗

NASA NTRS1983

Spherical micro-glass particle impingement studies of thermoplastic materials at normal incidence

Light optical and scanning electron microscope studies were conducted to characterize the erosion resistance of polymethyl methacrylate (PMMA), polycarbonate (PC), polytetrafluoroethylene (PTFE) and ultra-high-molecular-weight-polyethylene (UHMWPE). Erosion was caused by a jet of spherical micro-glass beads at normal impact. During the initial stages of damage, the surfaces of these materials were studied using a profilometer. Material buildup above the original surface was observed on PC and PMMA. As erosion progressed, this buildup disappeared as the pit became deeper. Little or no buildup was observed on PTFE and on UHMWPE. UHMWPE and PTFE are the most resistant materials and PMMA the least. Favorable properties for high erosion resistance seem to be high values of ultimate elongation, and strain energy and a low value of the modulus of elasticity. Erosion-rate-versus-time curves of PC and PTFE exhibit incubation, acceleration and steady state periods. A continuously increasing erosion rate period was observed however for PMMA instead of a steady state period. At early stages of damage and at low impact pressure material removal mechanisms appear to be similar to those for metallic materials.

Rao, P. V.↗

NASA NTRS1982

Empirical testing of structural deflection modeling of large photovoltaic modules

The objective of the structural deflection test was to verify the analytical models used to predict solar cell stress, load-bearing layer stress, and module deflection that result from a uniform pressure load on the module surface. The verification process consisted of measuring module deflection, stress in the solar cell, and stress in the load-bearing member as a functon of normal pressure load, pottant modulus of elasticity, pottant thickness, and cell location. Four glass superstrate modules, two plain wood substrate modules, two ribbed wood substrate modules, and a steel substrate module were tested. Consistent with analysis predictions, all unribbed specimens exhibited nonlinear load vs. deflection characteristics. With the exception of the steel module, test results and analysis predictions for panel deflectons agreed to within 10 percent. A wider variation of agreement was found for stress in the load-bearing members and cells.

Duncan, L. B.↗

NASA NTRS1984

Elastic model of the traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

Loewenthal, S. H.↗

NASA NTRS1984

Modification of epoxy-reinforced glass-cloth composites with a perfluorinated alkyl ether elastomer

A perfluorinated alkyl ether diacyl fluoride prepolymer (molecular weight about 1500) was coreacted with Epon 828 epoxy resin and diamino diphenyl sulfone to obtain an elastomer-toughened, glass-cloth composite. Improvements in flexural toughness, impact resistance, and water resistance, without loss of strength, modulus of elasticity or a lowering of the glass-transition temperature, were realized over those of the unmodified composite. Factors concerning optimization of the process are discussed. Results suggest that a simultaneously interpenetrating polymer network may be formed which gives rise to a measured improvement in composite mechanical properties.

Rosser, R. W.↗

NASA NTRS1984

Spherical microglass particle impingement studies of thermoplastic materials at normal incidence

Light optical and scanning electron microscope studies were conducted to characterize the erosion resistance of polymethyl methacrylate (PMMA), polycarbonate (PC), polytetrafluoroethylene (PTFE) and ultra-high-molecular-weight-polyethylene (UHMWPE). Erosion was caused by a jet of spherical micro-glass beads at normal impact. During the initial stages of damage, the surfaces of these materials were studied using a profilometer. Material buildup above the original surface was observed on PC and PMMA. As erosion progressed, this buildup disappeared as the pit became deeper. Little or no buildup was observed on PTFE and on UHMWPE. UHMWPE and PTFE are the most resistant materials and PMMA the least. Favorable properties for high erosion resistance seem to be high values of ultimate elongation, and strain energy and a low value of the modulus of elasticity. Erosion-rate-versus-time curves of PC and PTFE exhibit incubation, acceleration and steady state periods. A continuously increasing erosion rate period was observed however for PMMA instead of a steady state period. At early stages of damage and at low impact pressure material removal mechanisms appear to be similar to those for metallic materials.

Veerabhadra Rao, P.↗

NASA NTRS1985

Development of a continuous spinning process for producing silicon carbide - silicon nitride precursor fibers

An apparatus was designed for the continuous production of silicon carbide - silicon nitride precursor fibers. The precursor polymer can be fiberized, crosslined and pyrolyzed. The product is a metallic black fiber with the composition of the type C sub x Si sub y n sub z. Little, other than the tensile strength and modulus of elasticity, is known of the physical properties.

Source record↗

NASA NTRS1985

Angular particle impingement studies of thermoplastic materials at normal incidence

Scanning electron microscope studies were conducted to characterize the erosion resistance of polymethyl methacrylate (PMMA), polycarbonate (PC), polytetrafluorethylene (PTFE), and ultra-high-molecular-weight polyethylene (UHMWPE). Erosion was caused by a jet of angular microparticles of crushed glass at normal incidence. Material built up above the original surface on all of the materials. As erosion progressed, this buildup disappeared. UHMWPE was the most resistant material and PMMA the least. The most favorable properties for high erosion resistance were high values of ultimate elongation, maximum service temperature, and strain energy and a low value of the modulus of elasticity. Erosion-rate-versus-time curves of PC and PTFE exhibited incubation, acceleration, and steady-state periods. PMMA also exhibited a deceleration period, and an incubation period with deposition was observed for UHMWPE.

Rao, P. V.↗

NASA NTRS1987

Design study of advanced model support systems for the National Transonic Facility (NTF)

It has long been recognized that the sting (or support system) is a very critical part of the model system. The designer is frequently faced with the tradeoff of minimizing sting size, thereby compromising facility and model safety, against a larger sting and the subsequent problems of sting interference effects. In the NASA Langley Research Center National Transonic Facility (NTF), this problem is accentuated by the severe environment of high pressure/low temperature, designed into the facility to provide the desired high Reynolds number. Compromises in the configuration geometry and/or limiting the test envelope are therefore contrary to the purposes and goals of the NTF and are unacceptable. The results of an investigation aimed at improvements of 25% in both strength and Young's modulus of elasticity as compared to high strength cryogenically acceptable steels currently being used are presented. Various materials or combinations of materials were studied along with different design approaches. Design concepts were developed which included conventional material stings, advanced composites, and hybrid configurations. Candidate configurations are recommended.

Source record↗

NASA NTRS1988

Factors affecting the sticking of insects on modified aircraft wings

Previous work showed that the total number of insects sticking to an aluminum surface was reduced by coating the aluminum surface with elastomers. Due to a large number of possible experimental errors, no correlation between the modulus of elasticity, the elastomer, and the total number of insects sticking to a given elastomer was obtained. One of the errors assumed to be introduced during the road test is a variable insect flux so the number of insects striking one surface might be different from that striking another sample. To eliminate this source of error, the road test used to collect insects was simulated in a laboratory by development of an insect impacting technique using a pipe and high pressure compressed air. The insects are accelerated by a compressed air gun to high velocities and are then impacted with a stationary target on which the sample is mounted. The velocity of an object exiting from the pipe was determined and further improvement of the technique was achieved to obtain a uniform air velocity distribution.

Yi, O.↗

NASA NTRS1989

Screening of metal matrix composites using ultrasonic C-scans

Ultrasonic C-scans can be used to find some types of defects in continuous fiber-reinforced metal matrix composites such as boron/aluminum composites. These defects are related to the fatigue behavior and fracture location of each inspected specimen. The C-scan technique determined the relative amount of defects in boron/aluminum composites. The defects were primarily identified as gaps in the fiber spacing. Those specimens with higher defect densities had shorter fatigue lives, lower fatigue endurance limits, and greater reductions in the elastic unloading modulus (that is, stiffness) because of fatigue cycling. This type of data could be used to set accept/reject levels for a composite panel based on C-scan indications.

Johnson, W. S.↗

NASA NTRS1989

Experimental verification of damping mechanisms in a composite beam

A method of estimating the distributed damping parameters based on the measured modal parameters (frequency and damping ratios) was derived. Three different mathematical models were used to model the damping mechanism of a quasi-isotropic pultruded cantilevered beam. These three models were (1) viscous (air) damping, (2) strain rate damping, and (3) both viscous and strain rate damping. The eigenvalues of the partial differential equation model were found to be uninfluenced by any of the three assumed damping models. Values were obtained for each of the damping models as well as the modulus of elasticity of the beam. It was found that the two-parameter damping model provided the best fit to measured modal data. However, the two-parameter damping model could only reproduce the measured damping ratios to within 85 percent.

Cudney, Harley H.↗

NASA NTRS1989

Determining damping mechanisms in a composite beam by experimental modal analysis

A method of estimating the distributed damping parameters of a beam based on measured modal parameters (frequency and damping ratios) is derived. Three different mathematical models were used to model the damping mechanism of a quasi-isotropic pultruded cantilevered beam. These three models were (1) viscous (air) damping, (2) strain-rate damping, and (3) both viscous and strain-rate damping. Values were obtained for each of the damping models as well as the modulus of elasticity of the beam. It is found that the two-parameter damping model provides the best fit to measure modal data. However, the two-parameter damping model can only reproduce the measured damping ratios to within 85 percent.

Cudney, H. H.↗

NASA NTRS1991

Superfiber For Strong, Light Fabrics

New ultrahigh-molecular-weight fiber offers major advantages as fabric for space suits, diving suits, sporting goods, sails, and ultralight aircraft. Polyolefin fiber has extremely high modulus of elasticity, low elongation, high specific strength, low specific gravity, resistance to chemicals, low moisture absorption, and high resistance to damage by flexure and abrasion. Consists of elongated, highly aligned, highly crystalline polyethylene molecules. Structure not only results in high strength-to-weight ratio but also gives high resistance to tearing and ripping. Fibers woven in many patterns. Offers combination of desirable properties not found in nylon, polyester, or aramid fabrics.

Dawn, Frederic S.↗

NASA NTRS1990

Construction of the 16 meter Large Lunar Telescope (LLT)

The different materials that could be used to design the pedestal for a Moon based 16 meter telescope are discussed. The material that should be used has a low coefficient of thermal expansion, high modulus of elasticity, and high compressive and tensile strengths. For the model developed in this study, an aluminum-manganese alloy was used because of its low coefficient of thermal expansion. Due to variations in lunar soil conditions, both vertically and horizontally, three foundation systems are presented. The spudcan footing can be used in the case where dense soil is more than three meters. The spread footing is recommended where the dense soil is between one and three meters. Finally, in the third system, the Lunar Excursion Vehicle (LEV) is used as a base support for the telescope's pedestal. The LEV support requires a prepared site. The soil should be compacted and stabilized, if necessary, to reduce settlement.

Omar, Husam Anwar↗

NASA NTRS1992

Piezoelectric Measurement Of Bulk Modulus

In method of measuring bulk modulus of elasticity of elastomeric material, piezoelectric crystals of various sizes and energized by alternating voltage embedded in material. Concept demonstrated in test cell in which piezoelectric crystal mounted either unconstrained or between two rubber pads and connected as actuator in loud-speaker. The 1-in. diameter crystal excited with 24 Vac at 60 Hz. When crystal was unconstrained, it drew current of 0.8 mA. When crystal was constrained between rubber pads, current fell to 0.65 mA. Low current, minimal heating, and absence of arcing makes technique suitable for measurement of bulk moduli of elasticity of flammable or explosive rubbery materials.

Butler, Barry L.↗

NASA NTRS1992

Computer integrated laboratory testing

The objective is the integration of computers into the Engineering Materials Science Laboratory course, where existing test equipment is not computerized. The first lab procedure is to demonstrate and produce a material phase change curve. The second procedure is a demonstration of the modulus of elasticity and related stress-strain curve, plastic performance, maximum and failure strength. The process of recording data by sensors that are connected to a data logger which adds a time base, and the data logger in turn connected to a computer, places the materials labs into a computer integrated mode with minimum expense and maximum flexibility. The sensor signals are input into a spread sheet for tabular records, curve generation, and graph printing.

Dahl, Charles C.↗