Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUIDIZATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Exploratory design study on reactor configurations for carbon dioxide capture from conventional power plants employing regenerable solid sorbents

Preliminary commercial designs were carried out for a fluidized bed as a CO{sub 2} adsorber and a moving bed as a CO{sub 2} regenerator. Reverse engineering methodology was employed on the basis of a commercial 500 MW supercritical PC power plant whereby the boundaries required for a particular reactor design and configuration could be set. Employing the proposed moving bed for regenerator is, however, not promising because of poor heat transfer, evolution of CO{sub 2} during regeneration, and high pressure drop when small particles are used. If regeneration kinetics is as slow as reported in tens of minutes, the bed height can be quite high and the reactor can be quite costly. In its place, a so-called assisted self-fluidization bed with embedded heat transfer surface was proposed. Theoretically, there is no reason why the fluidized bed cannot be successfully designed and operated both as an adsorber and a regenerator under proper adsorption and regeneration kinetics. Recent publications, where fluidized beds, circulating fluidized beds, or a combination of them were employed both as an adsorber and a regenerator, were cited. Staging may not be necessary employing the fluidized bed technology because of the capability to control reaction temperature at the optimum operating temperature through embedded heat transfer surface in the fluidized beds. Even if the staging is necessary, the implementation of staging in fluidized beds at ambient pressure and moderate temperature is relatively easy and with minimum cost penalty. Example designs are presented.

01 COAL, LIGNITE, AND PEAT↗

Experiments on chemical looping combustion of coal with a NiO based oxygen carrier

A chemical looping combustion process for coal using interconnected fluidized beds with inherent separation of CO{sub 2} is proposed in this paper. The configuration comprises a high velocity fluidized bed as an air reactor, a cyclone, and a spout-fluid bed as a fuel reactor. The high velocity fluidized bed is directly connected to the spout-fluid bed through the cyclone. Gas composition of both fuel reactor and air reactor, carbon content of fly ash in the fuel reactor, carbon conversion efficiency and CO{sub 2} capture efficiency were investigated experimentally. The results showed that coal gasification was the main factor which controlled the contents of CO and CH{sub 4} concentrations in the flue gas of the fuel reactor, carbon conversion efficiency in the process of chemical looping combustion of coal with NiO-based oxygen carrier in the interconnected fluidized beds. Carbon conversion efficiency reached only 92.8% even when the fuel reactor temperature was high up to 970 C. There was an inherent carbon loss in the process of chemical looping combustion of coal in the interconnected fluidized beds. The inherent carbon loss was due to an easy elutriation of fine char particles from the freeboard of the spout-fluid bed, which was inevitable in this kind of fluidized bed reactor. Further improvement of carbon conversion efficiency could be achieved by means of a circulation of fine particles elutriation into the spout-fluid bed or the high velocity fluidized bed. CO{sub 2} capture efficiency reached to its equilibrium of 80% at the fuel reactor temperature of 960 C. The inherent loss of CO{sub 2} capture efficiency was due to bypassing of gases from the fuel reactor to the air reactor, and the product of residual char burnt with air in the air reactor. Further experiments should be performed for a relatively long-time period to investigate the effects of ash and sulfur in coal on the reactivity of nickel-based oxygen carrier in the continuous CLC reactor. (author)

01 COAL, LIGNITE, AND PEAT↗

Steam Reforming Process for Treating Radioactive Waste - 18172

In 2005 the THOR steam reforming fluidized-bed reactor (FBR) technology was selected by the DOE for treatment of sodium-bearing waste (SBW) at the INL. During commissioning a number of equipment reliability and process control challenges were encountered preventing the start of radiological operations. To address these challenges the team adopted a phased systematic mechanistic approach, underpinned by scientific principles and supported by some of the world's leading experts in FBR technology. The Phase 1 effort broadly addressed the entire plant and associated modifications. Phase 2 focused on the most critical issues associated with the denitration and mineralization reformer (DMR) vessel: specifically, mitigation of wall scale (mineral deposits) that formed on the inside of the DMR; mitigation of friable agglomerates (sand-castles) that caused operational instabilities; repair of damaged lower fluidizing gas distributor (ring header), and resolution of auger-grinder (A/G) reliability issues. Basic chemistry and fluidization, as well as operational issues were evaluated using engineering analysis, modeling, bench-scale, pilot scale, and full-scale runs to validate the resolutions. The bench scale testing revealed the need to ensure at least a 5 vol% concentration of CO{sub 2} in the fluidizing gas to minimize undesirable reaction intermediates that could form in less fluidized regions of the bed. Engineering analysis and modeling results pointed to the need to redesign the fluidizing gas distributor to overcome fluidization problems. Chemistry evaluations guided efforts to minimize the deposition of wall-scale. The process modifications were confirmed on the pilot level and are being validated in the full-scale unit (Phase 3). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Liquid-impregnated clay solid sorbents for CO{sub 2} removal from postcombustion gas streams

A novel liquid-impregnated clay sorbent (R. V. Siriwardane, U.S. Patent No. 6,908,497 B1 (2003)) was developed for carbon dioxide (CO{sub 2}) removal in the temperature range of ambient to 60{sup o}C for both fixed-bed and fluidized-bed reactor applications. The sorbent is regenerable at 80-100 {sup o}C. A 20-cycle test conducted in an atmospheric reactor with simulated flue gas with moisture demonstrated that the sorbent retains its CO{sub 2} sorption capacity with CO{sub 2} removal efficiency of about 99% during the cyclic tests. The sorbents suitable for fluidized-bed reactor operations showed required {delta} CO{sub 2} capacity requirements for sorption of CO{sub 2} at 40 {sup o}C and regeneration at 100{sup o}C. The parameters such as rate of sorption, heat of sorption, minimum fluidization velocities, and attrition resistance data that are necessary for the design of a reactor suitable for capture and regeneration were also determined for the sorbent. A 20-cycle test conducted in the presence of flue-gas pollutant sulfur dioxide - SO{sub 2} (20 parts per million) - indicated that the sorbent performance was not affected by the presence of SO{sub 2}.

01 COAL, LIGNITE, AND PEAT↗

Development of Enabling Technologies for Chemical Looping Combustion and Chemical Looping with Oxygen Uncoupling (Final Report)

This report summarizes results from the project, “Development of Enabling Technologies for Chemical Looping Combustion and Chemical Looping with Oxygen Uncoupling,” which evaluated several aspects of dual fluidized bed chemical looping combustion and chemical looping with oxygen uncoupling (CLOU). The objective was to provide tools and enabling technologies to help advance fluidized bed chemical looping technology to pilot, demonstration and commercial scale. One focus area is oxygen carriers, which are key to chemical looping combustion. The copper oxygen carrier-coal ash system was systematically evaluated through a combination of thermodynamic modeling and lab-scale experiments, taking into consideration different oxygen carrier support materials and coal types. A method of mapping “safe” and “risk” zones for different combinations was established, and recommendations for target conditions are provided. In addition, a simple solution for limiting negative influence of some coal ashes, namely adding small amounts of calcium to the system, is proposed. In addition, a novel process for recovering and recycling copper from spent oxygen carriers is proposed. A new approach for design and operation of loop seals in a CLOU system was developed, and involves distinct gas injection points and a short horizontal section to help control the fate of the fluidizing gases. For the air-to-fuel reactor loop seal, the upstream side is fluidized with air, ideally input into the side rather than into the bottom, which prevents uncoupling (reduction) of the oxygen carrier before entering the fuel reactor. Also, alternative for separating oxygen carrier particles and gas in circulating fluidized bed-based chemical looping system is proposed. A new reduced reaction scheme for conversion of coal in copper-based CLOU was developed and implemented into CPFD Software’s Barracuda VR package. The resulting model provides higher fidelity than the baseline, especially when it comes to minor reactions that are part of the overall combustion environment. For in-reactor heat extraction, it was determined in this project that the best way to do that in a dual circulating fluidized-bed system is through heat exchange low in the air reactor. The air reactor is the hotter of the two and for a fast-fluidized circulating bed, the lower, more dense section has a higher heat transfer coefficient and offers more consistent particle-wall contact since it doesn’t have the splashing behavior the top of the bed does. It was determined that just the wall surface area in the lower quarter to third of the air reactor is sufficient to control temperatures in both reactors. Finally, consideration was given to a new concept for CLC, which involves a staged fuel reactor with a different type of oxygen carrier in each stage.

01 COAL, LIGNITE, AND PEAT↗

Hydrodynamics and energy consumption studies in a three-phase liquid circulating three-phase fluid bed contactor

The hydrodynamics and energy consumption have been studied in a cold flow, bubbling and turbulent, pressurized gas-liquid-solid three-phase fluidized bed (0.15 m ID x 1 m height) with concurrent gas-liquid up flow is proposed with the intention of increasing the gas hold up. The hydrodynamic behaviour is described and characterised by some specific gas and liquid velocities. Particles are easily fluidized and can be uniformly distributed over the whole height of the column. The effect of parameters like liquid flow rate, gas flow rate, particle loading, particle size, and solid density on gas hold up and effect of gas flow rate, solid density and particle size on solid hold up, energy consumption and minimum fluidization velocity has been studied. At the elevated pressures a superior method for better prediction of minimum fluidization velocity and terminal settling velocities has been adopted. The results have been interpreted with Bernoulli's theorem and Richardson-Zaki equation. Based on the assumption of the gas and liquid as a pretend fluid, a simplification has been made to predict the particle terminal settling velocities. The Richardson-Zaki parameter n' was compared with Renzo's results. A correlation has been proposed with the experimental results for the three-phase fluidization. (author)

42 ENGINEERING↗

Managing Risks via Small/Pilot Scale Testing for INL's Integrated Waste Treatment Unit (IWTU) - 19268

In 2005, the THOR steam reforming fluidized-bed reactor (FBR) technology was selected by the U.S. Department of Energy (DOE) as the technology of choice for treatment of sodium- bearing waste (SBW) at the INL. The basis of the process was to use fluidized bed technology to convert an acidic radioactive nitrate-rich liquid waste into a solid carbonate product suitable for long-term disposal and storage. During initial commissioning, as well as subsequent start-ups, the plant faced many operational challenges, such as stagnant/de-fluidized bed, and wall-scale formation. Such operational issues prompted the original contractor to seek expertise in pilot-scale testing, thereby reaching out to Hazen Research Inc. (HRI, Golden, Co). Several tests were conducted, but the results did not seem to address the underlying issues observed in the full-scale plant, as evidenced by continued operational issues. A systematic approach was then taken by the Fluor-Idaho team (new contractor as of June 2016) with respect to solving these technical issues. First, two different bench-scale, 2-inch fluidized bed reactors (stainless-steal and quartz), were utilized to test several theories to better understand the underlying chemical reactions that may be taking place under expected normal operating conditions. Then, the team designed and built an 18-inch FBR unit, mimicking the full-scale main vessel at IWTU - Denitration Mineralization Reformer (DMR). This was used to test various aspects of operational challenges observed at IWTU, namely particle size control, wall-scale growth-rate control, long-term operational stability, process optimization, and process off- gas filtration challenges. An example of information obtained from bench-scale testing, which was then tested during pilot-scale testing, was the phenomena that an addition of 5 vol % of CO{sub 2} gas into the fluidizing gas system nearly eliminated the formation of agglomerates that had typically led to bed de-fluidization. This change proved to be correct in both the pilot and full-scale testing and will be implemented as part of a long-term operational strategy of IWTU. Several other findings that have provided answers with respect to IWTU operational issues will be discussed in this report. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A scalable Euler–Lagrange approach for multiphase flow simulation on spectral elements

Multiphase flow can be difficult to simulate with high accuracy due to the wide range of scales associated with various multiphase phenomena. These scales may range from the size of individual particles to the entire domain of interest. Traditionally, large scale systems can only be simulated using averaging approaches that filter out the locations of individual particles. In this work, the Euler–Lagrange method is used to simulate large-scale dense particle systems in which each individual particle is tracked. In order to accomplish this, the highly scalable spectral element code nek5000 has been extended to handle the multiple levels of multiphase coupling in these systems. These levels include what has been called one-, two-, and four-way coupling. Here, each level has been separated to detail the computational impact of each stage. A binned ghost particle algorithm has also been developed to efficiently handle the challenges of two- and four-way coupling in a parallel processing context. The algorithms and their implementations are then shown to scale to 65,536 Message Passing Interface (MPI) ranks in both the strong and weak limits. After this, validation is performed through simulation of a small-scale fluidized bed. Lastly, a large-scale fluidized bed is simulated with 65,536 MPI ranks and is able to capture the unique physics of the onset of fluidization.

Computer Science↗

Optimizing the Costs of Solid Sorbent-Based CO 2 Capture Process Through Heat Integration

The focus of this project was the ADAsorb™ CO 2 Capture Process, a temperature-swing adsorption process that incorporates a three-stage fluidized bed as the adsorber and a single-stage fluidized bed as the regenerator. ADAsorb™ system was designed, fabricated, and tested under DOE award DEFE0004343. Two amine-based sorbents were evaluated in conjunction with the ADAsorb™ process: “BN”, an ion-exchange resin; and “OJ”, a metal organic framework (MOF) sorbent. Two cross heat exchanger designs were evaluated for use between the adsorber and regenerator: moving bed and fluidized bed. The fluidized bed approach was rejected fairly early in the project because the additional electrical load to power blowers or fans to overcome the pressure drop required for fluidization was estimated to be nominally three times the electrical power that could be generated from the steam saved through the use of the cross heat exchanger. The Energy Research Center at Lehigh University built and utilized a process model of the ADAsorb™ capture process and integrated this model into an existing model of a supercritical PC power plant. The Lehigh models verified that, for the ADAsorb™ system, the largest contributor to parasitic power was lost electrical generation, which was primarily electric power which the host plant could not generate due to the extraction of low pressure (LP) steam for sorbent heating, followed by power for the CO 2 compressor and the blower or fan power required to fluidize the adsorber and regenerator. Sorbent characteristics such as the impacts of moisture uptake, optimized adsorption and regeneration temperature, and sensitivity to changes in pressure were also included in the modeling study. Results indicate that sorbents which adsorb more than 1-2% moisture by weight are unlikely to be cost competitive unless they have an extremely high CO 2 working capacity that well exceeds 15% by weight. Modeling also revealed that reductions in adsorber pressure drop could negatively affect the CO 2 adsorption characteristics for sorbents with certain isobar adsorption characteristics like sorbent BN. Thus, reductions in pressure drop do not provide the efficiency benefits expected. A techno-economic assessment conducted during the project revealed that without heat integration, the a metal organic framework (MOF) sorbent used in conjunction with the ADAsorb™ process provided the opportunity for improved performance over the benchmark MEA process. While the addition of a cross heat exchanger and heat integration was found to significantly improve net unit heat rate, the additional equipment costs required to realize these improvements almost always outweighed the improvement in performance. The exception to this was for a supported amine sorbent and the addition of a moving bed cross heat exchanger alone or in conjunction with waste heat from the compressor used for supplemental regenerator heating. Perhaps one of the most important points to be drawn from the work conducted during this project is the significant influence of sorbent characteristics alone on the projected COE and LCOE associated with the ADAsorb™ process, and the implications associated with future improvements to solid sorbent CO 2 capture. The results from this project suggest that solid sorbent CO 2 capture will continue to see performance gains and lower system costs as further sorbent improvements are realized.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Experimental and Simulation Analysis of Binary Mixtures of Biomass and Inert Material

A literature review was conducted to identify experiments on various scales of biomass combustion specific to circulating fluidized bed (CFB) combustors. Typical feedstock and inert bed material characteristics for biomass combustion in a CFB were gathered. This information was used to design laboratory-scale, non-reacting experiments on biomass-inert bed material mixtures in a 1-in. cylindrical test rig in the Multiphase Flow Analysis Laboratory (MFAL) in Morgantown, WV. The biomass chosen was a hardwood. Pellets from the hardwood were milled and sieved to obtain three size ranges—small, medium, and large. Three mass loadings of each of the biomass samples were fluidized with glass beads as the inert bed material to study the mixing characteristics under varying fluidizing gas velocities. Hydrodynamic data including pressure drop measurements at select vertical locations and video recordings of the mixture behavior were generated in this effort.

09 BIOMASS FUELS↗

Process for generating hydrogen from heavy oil or hydrocarbons

The present invention provides a steam reforming process for heavy oil or hydrocarbons using a circulating fluidized bed reactor, the process having a reforming step and a regeneration step, wherein the reforming step and the regeneration step comprise a bubbling fluidized reactor containing a fluidizable nickel-containing reforming catalyst and produce hydrogen as a product of the reforming bed. The API gravity of the feedstock may be between −11 and 54, preferably between −11 and 20. The present invention also provides a fluidized bed hydrocarbon steam reforming process using a regenerable catalyst to produce hydrogen, wherein a circulating bed reactor is operated in an alternating manner, switching between two steps: reforming and regeneration; using a mixture of a fluidizable solid and a fluidizable nickel-containing reforming catalyst; producing hydrogen as a product of the reforming step with a minimum hydrogen content of 25 volume percent, preferably at least 60 volume % and more preferably at least 70 volume percent on a dry weight basis.

Srinivas, Girish↗

Assessment of different coarse graining strategies to simulate polydisperse gas-solids flow

Continuum methods require the additional development of solids stress closures for polydisperse powders based on complex kinetic theories that are non-trivial to develop, code, and numerically converge for the wide range of fluidization regimes from very dilute to dense/frictional flow limit. On the other hand, it is straightforward to model the flow of polydisperse granular materials by treating particles as discrete rigid bodies that are tracked following simple physical laws of motion. The coarsening of these discrete methods by lumping several particles in a parcel alleviates the significant computational cost associated with these discrete methods while introducing some inaccuracies in the numerical results. In this research, we explore two different coarse graining methods that can be applied to polydisperse powders, namely the same statistic weight method (SSW) and the same size parcel method (SSP), and assess their accuracy by comparison with the finest simulation results obtained with a discrete element method (DEM). For Geldart group B powders fluidized at a relative low superficial velocity, the numerical results indicate that the SSW is more accurate than the SSP method. For type A powders fluidized at relatively high velocity, these two methods predict similar results. Interestingly, up to four times increase in the speed of simulation of the SSP method was obtained because the original polydisperse powder is scaled to a mono-disperse system in terms of particle-particle collision. Lastly, these results suggest that the SSP method is more favorable for the simulation of fluidized beds due to its accuracy and efficiency while the SSW method may be used for granular flow and dense fluidized bed systems where capturing the size segregation of particles due to collision is important.

42 ENGINEERING↗

Limitations for heavy metal release during thermo-chemical treatment of sewage sludge ash

Phosphate recycling from sewage sludge can be achieved by heavy metal removal from sewage sludge ash (SSA) producing a fertilizer product: mixing SSA with chloride and treating this mixture (eventually after granulation) in a rotary kiln at 1000 {+-} 100 deg. C leads to the formation of volatile heavy metal compounds that evaporate and to P-phases with high bio-availability. Due to economical and ecological reasons, it is necessary to reduce the energy consumption of this technology. Generally, fluidized bed reactors are characterized by high heat and mass transfer and thus promise the saving of energy. Therefore, a rotary reactor and a fluidized bed reactor (both laboratory-scale and operated in batch mode) are used for the treatment of granulates containing SSA and CaCl{sub 2}. Treatment temperature, residence time and - in case of the fluidized bed reactor - superficial velocity are varied between 800 and 900 deg. C, 10 and 30 min and 3.4 and 4.6 m s{sup -1}. Cd and Pb can be removed well (>95 %) in all experiments. Cu removal ranges from 25% to 84%, for Zn 75-90% are realized. The amount of heavy metals removed increases with increasing temperature and residence time which is most pronounced for Cu. In the pellet, three major reactions occur: formation of HCl and Cl{sub 2} from CaCl{sub 2}; diffusion and reaction of these gases with heavy metal compounds; side reactions from heavy metal compounds with matrix material. Although, heat and mass transfer are higher in the fluidized bed reactor, Pb and Zn removal is slightly better in the rotary reactor. This is due the accelerated migration of formed HCl and Cl{sub 2} out of the pellets into the reactor atmosphere. Cu is apparently limited by the diffusion of its chloride thus the removal is higher in the fluidized bed unit.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporization is included. • CFD predicted results agree well with experimental data reported in literature. • This approach may be helpful for fluidized bed reactor modelling purposes. - Abstract: Municipal Solid Waste Incineration (MSWI) in fluidized bed is a very interesting technology mainly due to high combustion efficiency, great flexibility for treating several types of waste fuels and reduction in pollutants emitted with the flue gas. However, there is a great concern with respect to the fate of heavy metals (HM) contained in MSW and their environmental impact. In this study, a coupled two-scale CFD model was developed for MSWI in a bubbling fluidized bed. It presents an original scheme that combines a single particle model and a global fluidized bed model in order to represent the HM vaporization during MSW combustion. Two of the most representative HM (Cd and Pb) with bed temperatures ranging between 923 and 1073 K have been considered. This new approach uses ANSYS FLUENT 14.0 as the modelling platform for the simulations along with a complete set of self-developed user-defined functions (UDFs). The simulation results are compared to the experimental data obtained previously by the research group in a lab-scale fluid bed incinerator. The comparison indicates that the proposed CFD model predicts well the evolution of the HM release for the bed temperatures analyzed. It shows that both bed temperature and bed dynamics have influence on the HM vaporization rate. It can be concluded that CFD is a rigorous tool that provides valuable information about HM vaporization and that the original two-scale simulation scheme adopted allows to better represent the actual particle behavior in a fluid bed incinerator.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Final Report: DOE/ID/14215

The proposed straw separation system developed in the research project harvests the large internode sections of the straw which has the greater potential as a feedstock for lignocellulosic ethanol production while leaving the chaff and nodes in the field. This strategy ensures sustainable agriculture by preventing the depletion of soil minerals, and it restores organic matter to the soil in amounts and particle sizes that accommodate farmers’ needs to keep tillage and fertilizer costs low. A ton of these nutrient-rich plant tissues contains as much as $10.55 worth of fertilizer (economic and energy benefits), in terms of nitrogen, phosphorus, potassium, and other nutrients provided to the soil when incorporated by tillage instead of being burned. Biomass conversion to fermentable sugars for the purpose of producing fuels, chemicals, and other industrial products is well understood. Most bioenergy strategies rely on low-cost fermentable sugars for sustainability and economic viability in the marketplace. Exploitation of the “whole crop”—specifically, wheat straw or other plant material currently regarded as residue or waste—is a practical approach for obtaining a reliable and low-cost source of sugars. However, industrial-scale production of sugars from wheat straw, while technically feasible, is plagued by obstacles related to capital costs, energy consumption, waste streams, production logistics, and the quality of the biomass feedstock. Currently available separation options with combine harvesters are not able to achieve sufficient separation of the straw/stover and chaff streams to realize the full potential of selective harvest. Since ethanol yield is a function of feedstock structural carbohydrate content, biomass anatomical fractions of higher product yield can have a significant beneficial impact on minimum ethanol selling price. To address this advanced biomass separation computation engineering models were developed to more effectively and efficiently engineer high-fidelity and high throughput separation systems for biomass components. INL and Iowa State University developed a computational modeling strategy for simulating multi-phase flow with an integrated solver using various computational fluid dynamics (CFD) codes. ISU set up a classic multi-phase test problem to be solved by the various CFD codes. The benchmark case was based on experimental data for bubble gas holdup and bed expansion for a gas/solid fluidized bed. Preliminary fluidization experiments identified some unexpected fluidization behavior, where rather than the bed uniformly fluidizing, a “blow out” would occur where a hole would open up in the bed through which the air would preferentially flow, resulting in erratic fluidization. To improve understanding of this phenomena and aid in building a design tool, improved computational tools were developed. The virtual engineering techniques developed were tested and utilized to design a separation baffle in a CNH combine. A computational engineering approach involving modeling, analysis, and simulation was used in the form of virtual engineering to design a baffle separator capable of accomplishing the high-fidelity residue separation established by the performance targets. Through the use of the virtual engineering model, baffle designs were simulated to (1) determine the effect of the baffle on the airflow of the combine cleaning system, and (2) predict the effectiveness of the baffle in separating the residue streams. A baffle design was selected based on the virtual engineering modeling, built into the INL selective harvest test combine. The result of the baffle changes improved the crop separation capability of the combine, enabling downstream improvement in composition and theoretical ethanol yield. In addition, the positive results from the application of the virtual engineering tools to the CNH combine design resulted in further application of these tools to other INL areas of research. INL and the University of Idaho identified, characterized, and modified a key plant biosynthetic lignin gene, cinnamoyl CoA reductase (CCR), to assess its influence on the efficiency with which the resulting biomaterials interact with and are processed by engineering systems. The characterization of CCR genes and resulting antisense gene constructs enabled the modification and assessment of the impact of cell wall biosynthetic gene in wheat. This allows the model systems needed to study the structural and functional post-harvest properties of straw to be created and assessed. Progress was made toward identifying and using key CCR lignin biosynthesis gene sequences for controlling lignin biosynthesis with the goal of altering lignin content and composition in wheat. This was important because of the potential impact that reduced lignin could have on feedstock harvesting, transportation, storage, pretreatment, and processing.

09 BIOMASS FUELS↗