SEARCH · Search NASA

Results for “High Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Determination of the SSME high pressure oxidizer turbopump bearing temperature

The SSME high pressure liquid oxygen turbopump (HPOTP) bearings sometimes wear and experience heating and oxidation of the ball and raceway surfaces. So far it has been impossible to measure the temperature of the bearings directly during operation of the turbopumps. However, a method was developed for determining the surface temperature of the bearings from the composition of the oxides using oxidation samples for calibration and Auger Electron Spectroscopy (AES) for chemical analysis.

Naerheim, Y.↗

NASA NTRS2003

Iron catalyst chemistry in modeling a high-pressure carbon monoxide nanotube reactor

The high-pressure carbon monoxide (HiPco) technique for producing single-wall carbon nanotubes (SWNTs) is analyzed with the use of a chemical reaction model coupled with flow properties calculated along streamlines, calculated by the FLUENT code for pure carbon monoxide. Cold iron pentacarbonyl, diluted in CO at about 30 atmospheres, is injected into a conical mixing zone, where hot CO is also introduced via three jets at 30 degrees with respect to the axis. Hot CO decomposes the Fe(CO)5 to release atomic Fe. Then iron nucleates and forms clusters that catalyze the formation of SWNTs by a disproportionation reaction (Boudouard) of CO on Fe-containing clusters. Alternative nucleation rates are estimated from the theory of hard sphere collision dynamics with an activation energy barrier. The rate coefficient for carbon nanotube growth is estimated from activation energies in the literature. The calculated growth was found be about an order of magnitude greater than measured, regardless of the nucleation rate. A study of cluster formation in an incubation zone prior to injection into the reactor shows that direct dimer formation from Fe atoms is not as important as formation via an exchange reaction of Fe with CO in FeCO.

Evaluation Studies↗

NASA NTRS2019

Outstanding Natural Occurrence of TiO2-II at the Chicxulub Crater - Anatomy of A Shock-Produced High-Pressure Polymorph

Scientific drilling of the end-Cretaceous, approximately 180 kilometers-diameter Chicxulub crater (Yucatan Peninsula, Mexico) during IODP–ICDP (Integrated Ocean Drilling Program - International Continental Scientific Drilling Program) Expedition 364 has provided new insights into the formation, shock metamorphism, structural evolution, and thermal history of peak rings in large complex impact craters. An outstanding feature in uplifted granitoid rocks of the Chicxulub peak ring is the preservation of TiO2-II, an orthorhombic high-pressure polymorph of TiO2 with an alpha-PbO2 structure, produced during the impact from rutile and/or anatase at shock pressures of approximately 12.5-17.5 gigapascals. Unlike other mostly micro- and cryptocrystalline occurrences of TiO2-II at terrestrial impact sites, ejecta deposits, and in rare ultra-high pressure metamorphic rocks, TiO2-II at Chicxulub occurs as abundant euhedral crystals greater than or equal to 70 microns in size within aggregates of altered magmatic titanite. This mode of occurrence provides an excellent opportunity to investigate the crystallography and transformation kinetics of the shock-produced high-pressure polymorph using scanning electron microscopic, micro-Raman, electron backscatter diffraction (EBSD), focused ion beam (FIB), as well as transmission-EBSD and transmission electron microscopic (TEM) techniques. Here we present refined microstructural and new crystallographic results for TiO2-II at the Chicxulub crater.

Schmieder, Martin↗

NASA NTRS1987

Elastomers Compatible With High-Pressure Oxygen

Compatibility increased by fluorination. Report describes experiments aimed at improving compatibility of some fluorinated elastomers with high-pressure oxygen. Such elastomers needed for seals, gaskets, and positive-expulsion devices used with high-pressure oxygen. Oxygen - compatibility tests carried out on five elastomers chosen on the basis of literature survey.

Martin, Jon W.↗

NASA NTRS1985

Hollow cathodes in high pressure arc discharges

An orified hallow cathode was tested at high pressure to improve lifetime and efficiency in arcjet thrusters. It is indicated that the arc would not operate with emission from the insert above 200 torr in nitrogen regardless of insert material, orifice diameter, or gas flow direction. Emission occurred from the insert in argon and xenon although it could not be ascertained whether diffuse or spot emission existed within the cathode. Over the extended range of configurations and operating parameters explored the desired diffuse emission mode could not be obtained at high enough pressures for orified hollow cathodes to operate in the range which is considered for arcjet applications.

Hardy, T. L.↗

NASA NTRS1985

Hollow cathodes in high pressure arc discharges

Hardy, T. L.↗

DOE OSTI2024

Structural transition and uranium valence change in UTe 2 at high pressure revealed by x-ray diffraction and spectroscopy

High-pressure x-ray diffraction up to 30 GPa, in conjunction with resonant emission x-ray spectroscopy and partial fluorescence yield x-ray absorption spectroscopy up to 52 GPa, were used to study how the structural and electronic properties of UTe2 evolve with pressure at room temperature. An orthorhombic-to-tetragonal phase transition was observed to occur between 5 and 7 GPa, with a large volume collapse of nearly 10% and a nearest U-U distance increase by about 4%. This lower-to-higher symmetry transition suggests less 5⁢f electron participation in bonding when the weakly correlated superconducting phase in the tetragonal structure of UTe 2 appears. Beyond 7 GPa, no new structural transitions were found up to 30 GPa. The resonant x-ray emission spectra clearly demonstrate an intermediate valence of U, nearly +3.74 at 1.8 GPa and room temperature, and reveal that the U valence shifts towards 4+, passes through a peak at 2.8 GPa, then decreases towards 3+ and settles down to a nearly constant value above 15 GPa. These experiments reveal that some fundamental structural and valence changes occur in UTe 2 at relatively low pressures, which could be responsible for the interplay between unconventional superconductivity, magnetic ordering, and weakly correlated superconductivity that is manifested in the temperature-pressure phase diagram of UTe 2 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1972

Phase equilibria in fluid mixtures at high pressures: The He-CH4 system

An experimental study of phase equilibria in the He-CH4 system was carried out over the temperature range 95 to 290 K and at pressures to 10,000 atm. The experimental results consist of equilibrium phase composition for twenty-eight isotherms in the region of coexistence of two fluid phases, together with the pressure-temperature trace of the three-phase boundary at which a CH4-rich solid phase is in equilibrium with the two fluid phases. The system exhibits a fluid-fluid phase separation which persists to temperatures and pressures beyond the range of this experiment. These results, together with those recently obtained for other binary systems, provide information about the form of phase diagrams for binary gas mixtures in the region of pressure induced phase transitions at high pressures. These findings are relevant to problems of deep atmosphere and interior structures in the outer planets.

Streett, W. B.↗

NASA NTRS2004

Innovative, High-Pressure, Cryogenic Control Valve: Short Face-to-Face, Reduced Cost

A control valve that can throttle high pressure cryogenic fluid embodies several design features that distinguish it over conventional valves designed for similar applications. Field and design engineers worked together to create a valve that would simplify installation, trim changes, and maintenance, thus reducing overall cost. The seals and plug stem packing were designed to perform optimally in cryogenic temperature ranges. Unlike conventional high-pressure cryogenic valves, the trim size can be changed independent of the body. The design feature that provides flexibility for changing the trim is a split body. The body is divided into an upper and a lower section with the seat ring sandwiched in between. In order to maintain the plug stem packing at an acceptable sealing temperature during cryogenic service, heat-exchanging fins were added to the upper body section (see figure). The body is made of stainless steel.

Wilkes, Karlin↗

DOE OSTI2024

Randomly Layered Superstructure of In 2 O 3 Truncated Nano-Octahedra and Its High-Pressure Behavior

This study outlines the synthesis and characterization of a unique superlattice composed of vertex-truncated indium oxide (In 2 O 3 ) nano-octahedra, along with an exploration of its response to high-pressure conditions. Here, using a bright-field transmission electron microscope (BF-TEM), we determined an average circumradius of 15.2 nm for these octahedral building blocks. The resilience and response of the superlattice to pressure variations, peaking at 18.01 GPa, were examined by employing synchrotron-based Wide-Angle X-ray Scattering (WAXS) and Small-Angle X-ray Scattering (SAXS) techniques. The WAXS data revealed no phase transitions, reinforcing the stability of the 2D superlattice comprised of random layers in alignment with a 2D p31m symmetry. Notably, the SAXS data unveiled a pressure-induced, irreversible octahedron translation and ligand interaction occurring within the random layer. Through our examination of these pressure-sensitive behaviors, we identified a distinctive translation model inherent to octahedra and observed modulation in the superlattice cell parameter induced by pressure. This research signifies a noteworthy progression in deciphering the intricate behaviors of 2D superlattices under high-pressure conditions.

36 MATERIALS SCIENCE↗

NASA NTRS1962

HYDRATES AT HIGH PRESSURES- METHANE-WATER AND ARGON-WATER SYSTEMS

Hydrates at high pressure - methane- and argon- water systems

METHANE↗

NASA NTRS1986

Ultrasonic level sensors for liquids under high pressure

An ultrasonic level sensor of novel design continuously measures the level of a liquid subjected to a high pressure (up to about 40 MPa), as is sometimes required for the effective transfer of the liquid. The sensor operates as a composite resonator fabricated from a standard high-pressure plug. A flat-bottom hole is machined into the plug along its center line. An ultrasonic transducer is bonded rigidly to the interior surface of the bottom wall, while the exterior surface is in contact with the liquid. Although the bottom wall is designed to satisfy the pressure code, it is still sufficiently thin to permit ready excitation of the axisymmetric plate modes of vibration. The liquid level is measured by a conventional pulse-echo technique. A prototype sensor was tested successfully in a 2300-l water vessel at pressures up to about 37 MPa. A spectral analysis of the transmitted pulse reveals that the flexural, extensional, thickness-shear, and radial plate modes are excited into vibration, but none of these appears to be significantly affected by the pressurization of the liquid.

Zuckerwar, A. J.↗

NASA NTRS1984

The preparation of BP single crystals by high pressure flux method

Single crystals of BP, a III-V compound semiconductor, were obtained by the high pressure flux method. Cu3P and Ni12P5 powders were used as the flux, and mixed with BP powder. Two kinds of mixtures were prepared: (1) 1.8g (BP) + 35 G (Cu3P) and (2) 1.7 g (BP) + 25 g (Ni12P5). They were compressed into pellets, heated at 1300 C for 24 h in an induction furnace under a pressure of 1 MPa using Ar-P2 gas, and slowly cooled to room temperature. In case (1), BP single crystals grew along the (III) plane, and in case (2) they grew as an aggregate of crystallites. The cathodoluminescence spectra of the synthetic BP crystals showed peaks near 680 nm (1.82 eV) for case (1), and 500 nm (2.47 eV) for case (2). By using the high pressure flux method conventional sized crystals were obtained in a relatively short time.

Kumashiro, Y.↗

DOE OSTI2022

High Pressure and Two-Sided Mold Surface Solutions (CRADA Final Report)

This project provided surface solutions for highly loaded precision tooling relevant to the automotive industry. Previous development work in coatings for Big Area Additive Manufacturing (BAAM) has produced commercialized coatings for low temperature Acrylonitrile Butadiene Styrene (ABS) tools (TD Coat RT) as well as a soft coating for high temperature applications (TD Seal HT). The team developed these coatings and commercialized them during a prior Manufacturing Demonstration Facility (MDF) technical collaboration (NFE-15-05793). During the prior collaboration, commercialization testing was successfully performed by the Boeing and NAVAIR and resulted in an Awards for Composites Excellence (ACE), award at CAMX – The Composites and Advanced Materials Expo 2016. While this work was clearly successful, gaps in the technology were identified, that prevent widespread adoption of large-scale additive manufacturing in high pressure tooling applications prevalent in the automotive industry. In this project we focused on development of surface solutions for two-sided, compression molding tooling printed on a large-scale polymer AM system in an arbitrary build orientation. We have printed a single cavity extrusion compression molding mold using Polyphenylene sulfide/carbon fiber (PPS/CF) materials, 50% by weight CF samples. These processes are commonly used by Original Equipment Manufacturers (OEM) and Tier 1 suppliers for high volume automotive applications. Several OEMs have identified the need for such technology, indicating significant time and monetary savings could be possible if commercially available surface solutions for high pressure Additive Manufacturing (AM) tooling existed.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Full waveform analysis for high pressure ultrasonic measurement

In this paper we report a data analysis protocol for ultrasonic velocity measurements carried out in a synchrotron x-ray facility based multi-anvil high-pressure apparatus. Synthetic ultrasonic signals for the time period between echoes from the two ends of the sample assembly are created with a few simple parameters as the echo waveform is modeled by the first echo from the anvil-assembly boundary. Each echo is modeled as a delta function with an amplitude and arrival time and convolved with this waveform. The final waveform, fit to the data, enables analysis of signals with overlapped echoes as they are common in small cell assemblies and high pressure.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Exploring the hardness and high-pressure behavior of osmium and ruthenium-doped rhenium diboride solid solutions

Rhenium diboride (ReB 2 ) exhibits high differential strain due to its puckered boron sheets that impede shear deformation. Here, we demonstrate the use of solid solution formation to enhance the Vickers hardness and differential strain of ReB 2 . ReB 2 -structured solid solutions (Re 0.98 Os 0.02 B 2 and Re 0.98 Ru 0.02 B 2 , noted as “ReOsB 2 ” and “ReRuB 2 ”) were synthesized via arc-melting from the pure elements. In-situ high-pressure radial x-ray diffraction was performed in the diamond anvil cell to study the incompressibility and lattice strain of ReOsB 2 and ReRuB 2 up to ~56 GPa. Both solid solutions exhibit higher incompressibility and differential strain than pure ReB 2 . However, while all lattice planes are strengthened by doping osmium (Os) into the ReB 2 structure, only the weakest ReB 2 lattice plane is enhanced with ruthenium (Ru). These results are in agreement with the Vickers hardness measurements of the two systems, where higher hardness was observed in ReOsB 2 . The combination of high-pressure studies with experimentally observed hardness data provides lattice specific information about the strengthening mechanisms behind the intrinsic hardness enhancement of the ReB 2 system.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Oxygen Reduction Reaction Activity of Nanocolumnar Platinum Thin Films by High Pressure Sputtering

Nanocolumnar platinum thin films (Pt-TFs) were produced by high pressure sputtering (HIPS) and investigated as oxygen reduction reaction electrocatalysts for polymer electrolyte membrane fuel cells. Conventional high-density Pt-TF prepared by low pressure sputtering was also studied for comparison. Pt-TFs were deposited on a microporous layer (MPL)-like surface composed of carbon particles to mimic catalyst-coated gas diffusion electrodes. Electron microscopy imaging revealed that HIPS Pt-TFs developed a cauliflower-like columnar microstructure, which originated from a shadowing effect during HIPS. This shadowing effect is enhanced on the rough surface of the MPL-like carbon that leads to the nano-cauliflower formation. With this approach, we also aimed to relate the catalyst performance obtained by benchtop tests directly to membrane electrode assembly test results. The electrochemically active surface area of Pt-TFs increased from 10 to 19 m 2 /g with increasing sputter pressure. Specific activity of conventional high-density and nanocolumnar films were similar at ~600 μA/cm 2 , which is likely due to their similar crystal grain sizes, >5 nm. On the other hand, mass-specific (MA) activity values increased from ~0.06 A/mgPt for conventional Pt-TF to ~0.13 A/mgPt for HIPS Pt-TFs, which is consistent with the columnar microstructure of HIPS films providing a better catalyst utilization compared to conventional Pt-TF.

08 HYDROGEN↗

DOE OSTI2022

High-pressure structural systematics of dysprosium metal compressed in a neon pressure medium to 182 GPa

Here we present an experimental and theoretical study of dysprosium metal compressed in the soft pressure transmitting medium Ne up to 182 and 300 GPa, respectively. Angle-dispersive x-ray powder diffraction data from each of the high-pressure polymorphs shows anisotropic compression behavior indicating changes to the electron density distribution throughout its polymorphic landscape. We compare the monoclinic (mC4) and orthorhombic (oF16) structures for the collapsed structure for Dy above 82 GPa and verify that the oF16 structure offers a better fit to our data than the previously reported mC4 structure. Further, we have found that the oF16 structure undergoes similar anisotropic compression of its lattice parameters, with a turning point above 160 GPa; suggesting a potential phase transition at pressures much higher than achieved in this study. Density functional theory calculations show the likely candidate for this new high-pressure phase is the isosymmetric oF8 structure, which is predicted to be lower in energy than the oF16 structure above 275 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗