SEARCH · Search NASA

Results for “Lift to Drag Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1983

System technology analysis of aeroassisted orbital transfer vehicles - Moderate lift/drag

The utilization of procedures involving aerodynamic braking and/or aerodynamic maneuvering on return from higher altitude orbits to low-earth orbit makes it possible to realize significant performance benefits. The present study is concerned with a number of mission scenarios for Aeroassisted Orbital Transfer Vehicles (AOTV) and the impact of potential technology advances in the performance enhancement of the class of AOTV's having a hypersonic lift to drag ratio (L/D) of 0.75 to 1.5. It is found that the synergistic combination of a hypersonic L/D of 1.2, an advanced cryopropelled engine, and an LH2 drop tank (1-1/2 stage) leads to a single 65,000 pound shuttle, two-man geosynchronous mission with 2100 pounds of useful paylod. Additional payload enhancement is possible with AOTV dry weight reductions due to technology advances in the areas of vehicle structures and thermal protection systems and other subsystems.

Florence, D. E.↗

NASA NTRS1983

Recent studies at NASA-Langley of vortical flows interacting with neighboring surfaces

The importance of leading edge vortical flows, which occur near and interact with neighboring surfaces, is stressed. Research in this area conducted or sponsored by the NASA Langley Research Center since 1978 is surveyed. Particular attention is given to the cumulative results of a number of theoretical and experimental studies. It is noted that these studies have been carried out in order to understand and use this kind of flow. Much of the work has been devoted to improving the lift-to-drag ratio and pitch characteristics for wings in this flow, although work has also been done on examining the unsteady and lateral characteristics.

Lamar, J. E.↗

NASA NTRS1984

Design of a composite wing extension for a general aviation aircraft

A composite wing extension was designed for a typical general aviation aircraft to improve lift curve slope, dihedral effect, and lift to drag ratio. Advanced composite materials were used in the design to evaluate their use as primary structural components in general aviation aircraft. Extensive wind tunnel tests were used to evaluate six extension shapes. The extension shape chosen as the best choice was 28 inches long with a total area of 17 square feet. Subsequent flight tests showed the wing extension's predicted aerodynamic improvements to be correct. The structural design of the wing extension consisted of a hybrid laminate carbon core with outer layers of Kevlar - layed up over a foam interior which acted as an internal support. The laminate skin of the wing extension was designed from strength requirements, and the foam core was included to prevent buckling. A joint lap was recommended to attach the wing extension to the main wing structure.

Adney, P. S.↗

NASA NTRS1984

Performance aerodynamics of aeroassisted orbital transfer vehicles

A method for predicting the performance aerodynamics of aeroassisted orbital transfer vehicles was developed based on techniques that were used in the aerodynamic databook of the Space Shuttle orbiter and theories from the Hypersonic Arbitrary Body Program. The method spans the entire flight profile of the aeroassisted orbital transfer vehicles from the extreme high altitude non-continuum regime to the highly viscous continuum regime. Results from this method are compared with flight data from the Shuttle orbiter, Apollo Capsule, and the Viking Aeroshell. Finally, performance aerodynamics are estimated for three aeroassisted orbital transfer vehicles that range from low to high lift-to-drag ratio configurations.

Wilhite, A. W.↗

NASA NTRS1984

Numerical optimization of circulation control airfoil at high subsonic speed

A numerical procedure for optimizing the design of the circulation control airfoil for use at high subsonic speeds is presented. The procedure consists of an optimization scheme coupled with a viscous potential flow analysis for the blowing jet. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse and cambered ellipse with drooped and spiraled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the airfoil, optimized at free-stream Mach 0.54 and alpha = -2 degrees can be characterized as a cambered ellipse with a drooped trailing edge. Experimental tests support the performance improvement predicted by numerical optimization.

Tai, T. C.↗

NASA NTRS1984

Active Control Technology Experience with the Space Shuttle in the Landing Regime

The shuttle program took on the challenge of providing a manual landing capability for an operational vehicle returning from orbit. Some complex challenges were encountered in developing the longitudinal flying qualities required to land the orbiter manually in an operational environmental. Approach and landing test flights indicated a tendency for pilot-induced oscillation near landing. Changes in the operational procedures reduced the difficulty of the landing task, and an adaptive stick filter was incorporated to reduce the severity of any pilot-induced oscillatory motions. Fixed-base, moving-base, and in-flight simulations were used for the evaluations, and in general, flight simulation was the only reliable means of assessing the low-speed longitudinal flying qualities problems. Overall, the orbiter control system and operational procedures have produced a good capability for routinely performing precise landings in a large, unpowered vehicle with a low lift-to-drag ratio.

Powers, B. G.↗

NASA NTRS1985

Low-speed longitudinal orbiter qualities

The shuttle program took on the challenge of providing a manual landing capability for an operational vehicle returning from orbit. Some complex challenges were encountered in developing the longitudinal flying qualities required to land the orbiter manually in an operational environment. Approach and landing test flights indicated a tendency for pilot-induced oscillation near landing. Changes in the operational procedures reduced the difficulty of the landing task, and an adaptive stick filter was incorporated to reduce the severity of any pilot-induced oscillatory motions. Fixed-base, movingbase, and in-flight simulations were used for the evaluations, and in general, flight simulation was the only reliable means of assessing the low-speed longitudinal flying qualities problems. Overall, the orbiter control system and operational procedures have produced a good capability to routinely perform precise landings with a large, unpowered vehicle with a low lift-to-drag ratio.

Powers, B. G.↗

NASA NTRS1984

Performance assessment of aero-assisted orbital transfer vehicles

Aero-assisted orbital transfer vehicles are analyzed. The aerodynamic characteristics over the flight profile and three- and six-degree-of-freedom performance analyses were determined. The important results, to date, are: (1) the aerodynamic preliminary analysis system, an interactive computer program, used to predict the aerodynamics (performance, stability, and control) for these vehicles; (2) the performance capability, e.g., maximum inclination change, maximum heating rate, and maximum sensed acceleration, can be determined using continuum aerodynamics only; (3) guidance schemes can be developed that allow for errors in atmospheric density prediction, mispredicted trim angle of attack, and off-nominal atmospheric interface conditions, even for vehicles with a low lift-to-drag ratio; and (4) multiple pass trajectories can be used to reduce the maximum heating rate.

Powell, R. W.↗

NASA NTRS1985

Active control technology experience with the Space Shuttle in the landing regime

The shuttle program took on the challenge of providing a manual landing capability for an operational vehicle returning from orbit. Some complex challenges were encountered in developing the longitudinal flying qualities required to land the orbiter manually in an operational environment. Approach and landing test flights indicated a tendency for pilot-induced oscillation near landing. Changes in the operational procedures reduced the difficulty of the landing task, and an adaptive stick filter was incorporated to reduce the severity of any pilot-induced oscillatory motions. Fixed-base, moving-base, and in-flight simulations were used for the evaluations, and in general, flight simulation has been the only reliable means of assessing the low-speed longitudinal flying qualities problems. Overall, the orbiter control system and operational procedures have produced a good capability for routinely performing precise landings in a large, unpowered vehicle with a low lift-to-drag ratio.

Powers, B. G.↗

NASA NTRS1985

In-flight evaluation of pure time delays in pitch and roll

An in-flight investigation of the effect of pure time delays in pitch and roll was undertaken. The evaluation tasks consisted of low lift-to-drag-ratio landings of various levels of difficulty and formation flying. The results indicate that the effect of time delay is strongly dependent on the task. In the pitch axis, in calm air, spot landings from a lateral offset were most strongly influenced by time delay. In the roll axis, in calm air, formation flying was most strongly influenced by time delay. However, when landings were made in turbulence, flying qualities in pitch were only slightly degraded, whereas in roll they were severely degraded.

Berry, D. T.↗

NASA NTRS1985

Optimum configuration of high-lift aeromaneuvering orbital transfer vehicles in viscous flow

The results of an analysis to determine the geometrical configuration of an aeroassisted transfer vehicle with a high lift-to-drag ratio (L/D) are described and the constraints imposed on this type of entry vehicle are considered. The aerodynamic characteristics of three configurations, a flat-plate delta wing, a truncated straight cone, and a truncated bent biconic are compared. The effect of viscosity is included in the analysis which examines the rounding of the sharp leading edges. It is shown that, under the constraints of carrying a given volume in the dead air region, the values of L/D are similar for each configuration and that a small blunt leading edge only slightly affects each vehicle's aerodynamic performance, causing less than a 5 percent drop in L/D. The truncated bent biconic is found to be the only configuration that provides the necessary stabilizing moments.

Davies, C. B.↗

NASA NTRS1985

In-flight evaluation of pure time delays in pitch and roll

Berry, D. T.↗

NASA NTRS1986

Rarefied aerodynamics and upper atmosphere density from multiple orbiter flight measurements

Flight data from six flights of the experimental High Resolution Accelerometer Package (HIRAP), a micro-g accelerometer system, have been analyzed to produce rarefied flow aerodynamic coefficients of the Orbiter and freestream density in the altitude range from 60 km to 160 km. The direct measurements of the lift to drag ratio (L/D) are used to obtain individual normalized body-axis force coefficients in a least-squares regression scheme. An aerodynamics model based on an exponential function of Knudsen number is used for the individual coefficients. The calculated L/D from the flight determined coefficients agree with the multiple flight data measurements to within about 5 percent. Simultaneously, an upper altitude density variation is also obtained from the data. Density altitude profiles exhibit a wave feature on all flights. The wave has an amplitude of about + or - 25 percent relative to the 1962 Standard atmosphere model.

Buck, G. M.↗

NASA NTRS1985

Reentry guidance and control for an Aeroassist Flight

An Aeroassist Flight Experiment (AFE) is proposed to show how the use of an atmospheric braking device can reduce the perigee velocity of a vehicle upon its return from a mission to geosynchronous orbit. This braking device would be used to attain low earth orbit comparable with the STS Orbiter. The basic design of the AFE is presented and the guidance and control aspects of the design are discussed. The lifting-brake design selected for the AFE is a raked cone with a coefficient of drag of 1.5 and a lift to drag ratio of 0.3. The potential second flight of the AFE would have a ballute aerobraking device with a predictor/corrector guidance scheme. It is concluded that the approach described to implement the AFE is a feasible one and minimizes risk by having adequate margins wherever needed, by reducing error sources in sensitive areas, and by conducting an extensive simulation activity to verify the design.

Brandon, L. B.↗

NASA NTRS1986

Rarefied flow lift-to-drag measurements of the Shuttle Orbiter

This report presents a discussion of the analysis and the results of sensitive micro-g accelerometry measurements on the Shuttle Orbiter in the rarefied flow flight regime, that is, from altitudes of 60 km to 160 km. A brief description of the experimental apparatus called High Resolution Accelerometer Package (HiRAP) is given along with a description of the ground processing to obtain the lift-to-drag ratio (L/D) from the flight measurements. The flight results of L/D from six missions are presented and discussed. Comparisons are made with preflight wind tunnel data in the near continuum viscous interaction regime and preflight analytical estimates in the rarefied transition regime. Excellent agreement is obtained between flight and wind tunnel data in the viscous regime, but differences are noted between flight and preflight predictions in the transition regime. Free molecule flow F/D data are also obtained on each mission. Comparisons of flight data with classical theory show that complete diffuse reflection is not an appropriate model for rarefied aerodynamic coefficient calculations, and, for the Shuttle, some specular fraction is required. Surface reflection laws are explored to define the sensitivity of the L/D measurements to gas-surface molecule interactions.

Blanchard, R. C.↗

NASA NTRS1986

Space Shuttle longitudinal landing flying qualities

The Space Shuttle program took on the challenge of providing a manual landing capability for an operational vehicle returning from orbit. Some complex challenges were encountered in developing the longitudinal flying qualities required to land the Orbiter manually in an operational environment. Approach and landing test flights indicated a tendency of pilot-induced oscillation near landing. Changes in the operational procedures reduced the difficulty of the landing task, and an adaptive stick filter was incorporated to reduce the severity of any pilot-induced oscillatory motions. Fixed-base, moving-base, and in-flight simulations were used for the evaluations. Overall, the Orbiter control system and operational procedures produced a good capability to perform routinely precise landings with a large, unpowered vehicle that has a low lift-to-drag ratio.

Powers, B. G.↗

NASA NTRS1987

Rarefied aerodynamics and upper atmospheric flight results from the Orbiter High Resolution Accelerometer Package experiment

Data from the High Resolution Accelerometer Package (HiRAP) experiment on the Space Shuttle Orbiter have been analyzed for 10 flights to produce lift-drag (L/D) ratios in the free molecule, transition, and continuum flow flight regimes. Freestream density is also obtained in the altitude range from 60 km to 160 km using an aerodynamic model based upon earlier flight analysis of accelerometer data. The results of the L/D analysis of the latest four flights have been compared with the aerodynamic model developed from the first six HiRAP missions. The new data agree with the established flight-derived model, thereby validating earlier analysis. However, the arithmetic mean of the 10 flight-derived L/D values in the free molecular flow regime is 0.053 (+ or - 0.1) as compared to the initial value of 0.10 (+ or - 0.3), determined from STS-6. Updates to the Orbiter aerodynamic model values and calibration factors have been incorporated into the density calculations for all 10 flights to provide realistic absolute density. The derived density altitude profiles, which have been normalized to the U.S. Standard Atmosphere 1976, are characterized by a large amplitude wave pattern relative to the standard as seen in the initial flight analysis.

Blanchard, R. C.↗

NASA NTRS1988

Application of Hybrid Laminar Flow Control to Global Range Military Transport Aircraft

A study was conducted to evaluate the application of hybrid laminar flow control (HLFC) to global range military transport aircraft. The global mission included the capability to transport 132,500 pounds of payload 6500 nautical miles, land and deliver the payload and without refueling return 6500 nautical miles to a friendly airbase. The preliminary design studies show significant performance benefits obtained for the HLFC aircraft as compared to counterpart turbulent flow aircraft. The study results at M=0.77 show that the largest benefits of HLFC are obtained with a high wing with engines on the wing configuration. As compared with the turbulent flow baseline aircraft, the high wing HLFC aircraft shows 17 percent reduction in fuel burned, 19.2 percent increase in lift-to-drag ratio, an insignificant increase in operating weight, and a 7.4 percent reduction in gross weight.

Lange, Roy H.↗