Search NASA⌕ Search

SEARCH · Search NASA

Results for “Link length”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Air Traffic Control Improvement Using Prioritized CSMA

Version 7 simulations of the industry-standard network simulation software "OPNET" are presented of two applications of the Aeronautical Telecommunications Network (ATN), Controller Pilot Data Link Communications (CPDLC) and Automatic Dependent Surveillance-Broadcast mode (ADS-B), over VHF Data Link mode 2 (VDL-2). Communication is modeled for air traffic between just three cities. All aircraft are assumed to have the same equipage. The simulation involves Air Traffic Control (ATC) ground stations and 105 aircraft taking off, flying realistic free-flight trajectories, and landing in a 24-hr period. All communication is modeled as unreliable. Collision-less, prioritized carrier sense multiple access (CSMA) is successfully tested. The statistics presented include latency, queue length, and packet loss. This research may show that a communications system simpler than the currently accepted standard envisioned may not only suffice, but also surpass performance of the standard at a lower cost of deployment.

Robinson, Daryl C.↗
DOE OSTI2025

Structural Investigation of Six Quinary Sulfides Synthesized via the Flux-Assisted Boron-Chalcogen Mixture (BCM) Method: Eu 2+ Containing Members of the RE 3 MTQ 7 (M and T = Transition or Main Group Metals, Q = Chalcogens) Family

For this work, a series of six quinary rare-earth sulfides Ce 4+ 1.85 Eu 2+ 1.15 Na 0.30 SiS 7 , Ce 4+ 1.91 Eu 2+ 1.09 K 0.18 SiS 7 , Ce 4+ 1.96 Eu 2+ 1.04 Rb 0.08 SiS 7 , Ce 4+ 1.98 Eu 2+ 1.02 Cs 0.05 SiS 7 , Ce 4+ 1.97 Eu 2+ 1.03 Ag 0.06 SiS 7 , and Ce 4+ 1.50 Eu 2+ 1.50 CuSiS 7 were obtained in an alkali iodide flux using the boron-chalcogen mixture (BCM) method. Single crystal X-ray diffraction was used to determine the structures of the high quality single crystals that were grown; their elemental compositions were confirmed by energy-dispersive spectroscopy (EDS). The compounds crystallize in the hexagonal crystal system in the noncentrosymmetric space group P63. The crystal structure consists of a three-dimensional network composed of mixed cerium and europium bicapped trigonal prisms, isolated SiS4 tetrahedra, and monovalent metals (Na, K, Rb, Cs, Ag, and Cu) located in cavities created by linked Ce/EuS 8 polyhedra. The structures are charge-balanced when Ce and Eu are in their +4 and +2 oxidation states, respectively. The effective magnetic moment of Ce 1.50 4+ Eu 1.50 2+ CuSiS 7 determined from the temperature dependence of the magnetic susceptibility data is consistent with the presence of Ce 4+ and Eu 2+ . Clear correlations between the alkali ion site occupancy, the ionic radius of the alkali cations, and the average bond length of Ce 4+ /Eu 2+ –S, were established. UV–vis diffuse reflectance data were collected for Ce 1.50 4+ Eu 1.50 2+ CuSiS 7 and a band gap of 1.9(1) eV was established.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

High precision monitoring of outgassing species in model EUV photoresists with a cavity ring-down spectrometer

Extreme ultraviolet (EUV) photoresists play a pivotal role in advancing nanopatterning technologies by balancing image quality and sensitivity. The outgassing behavior of photoresist thin films under EUV and deep ultraviolet (DUV) exposure reveals chemical details relevant to their performance. This study focuses on utilizing an analytical technique not previously used in photolithography, the tabletop cavity ring-down spectrometer, to investigate outgassing dynamics in EUV photoresists, enabling precise chemical identification and deeper insights into resist processing. The spectrometer’s enhanced laser path length (~20 km) and broadband absorption capabilities in the CH overtone region allow for sensitive and temporally resolved detection of outgassed species. Using a model resist comprising a polymer matrix with a photoacid generator and quencher, we analyzed the influence of time delays between exposure and Post-Exposure Bake (PEB) as well as storage under varying environmental conditions. Suppression of isobutylene outgassing and thickness loss was observed with extended delays between exposure and PEB, potentially linked to water absorption and acid deactivation. The technique proved highly effective in distinguishing subtle chemical differences between processing stages. Delay times and their environmental conditions, particularly humidity, reduce outgassing and thickness loss of photoresists during PEB, suggesting decreased acid-driven deprotection. This can potentially impact sensitivity, defectivity, and roughness of resist patterns, necessitating precise monitoring and control.

Lüttgenau, Bernhard↗
DOE OSTI2022

Resolution Study of Thermonuclear Initiation in White Dwarf Tidal Disruption Events

Abstract We study the initiation of thermonuclear detonations in tidally disrupted white dwarf stars by intermediate-mass (10 3 M ⊙ ) black holes. The length scales required to resolve the initiation mechanism are not easily reached in 3D, so instead we have devised 2D proxy models, which, together with a logarithmic gridding strategy, can adequately capture detonation wave fronts as material undergoes simultaneous compression and stretching from tidal forces. We consider 0.15 and 0.6 M ⊙ white dwarf stars parameterized by tidal strengths in the range β = 4–23. High spatial resolution elucidates the manner and conditions leading to thermonuclear detonation, linking the initiation sequence to stellar composition and tidal strength. All of our models suffer sustained detonations triggered by a combination of adiabatic compression, mild thermonuclear preconditioning, and collisional heating, in degrees depending primarily on tidal strength. We find that many diagnostics, such as temperature, total released energy, and iron-group products, are fairly well converged (better than 10%) at resolutions below 10 km along the scale height of the orbital plane. The exceptions are intermediate-mass transients like calcium, which remain uncertain up to factors of 2, even at 1 km resolution.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Rapid organic carbon spiraling in a headwater stream linked with streamflow, biogeochemistry, and canopy phenology

Headwater streams are abundant worldwide and important to global biogeochemical cycles, serving as critical processors and transporters of C. C spiraling is a useful way to understand the retention and mineralization of organic C (OC) in streams. However, analyses of seasonal and interannual variability in OC spiraling are currently limited. In this study, we aimed to understand the temporal patterns and driving mechanisms of OC spiraling, which will inform our understanding of future OC changes under climate change. We used 7 y of daily data in a small headwater stream (Walker Branch, Tennessee, USA) to assess seasonal and interannual variability in OC spiraling length (S OC ) and mineralization velocity (v fOC ), as well as their potential related variables. On average, S OC in Walker Branch was ~10× shorter than in previously studied small streams, indicating strong connections between the water column and the benthic environment where OC mineralization mostly takes place. OC spiraling was faster during the more biologically active periods of spring and autumn compared with more elongated OC spiraling in summer and winter, when OC retention was lower and downstream transport was higher. Gross primary production (GPP) was most strongly related to S OC and v fOC . Photosynthetically active radiation (PAR) and NO 3 − were also positively and negatively related to v fOC , respectively. Trends toward earlier and longer canopy cover and reduced GPP and PAR may result in longer S OC and slower v fOC , reducing localized instream processing of OC and potentially shunting more OC downstream. However, long-term observations indicate reduced NO 3 − at Walker Branch, suggesting opposing effects to those of GPP and PAR, leading to faster v fOC and greater OC retention. Time-series analyses of OC spiraling in streams can enhance our understanding of current and future responses of OC processing and downstream transport to climate change, as well as implications for downstream OC dynamics.

biological activity↗
DOE OSTI2024

Comparison of detachment in Ohmic plasmas with positive and negative triangularity

Abstract In recent years, negative triangularity (NT) has emerged as a potential high-confinement L-mode reactor solution. In this work, detachment is investigated using core density ramps in lower single null Ohmic L-mode plasmas across a wide range of upper, lower, and average triangularity (the mean of upper and lower triangularity: δ ) in the TCV tokamak. It is universally found that detachment is more difficult to access for NT shaping. The outer divertor leg of discharges with δ ≈ − 0.3 could not be cooled to below 5 eV through core density ramps alone. The behavior of the upstream plasma and geometrical divertor effects (e.g. a reduced connection length with negative lower triangularity) do not fully explain the challenges in detaching NT plasmas. Langmuir probe measurements of the target heat flux widths ( λ q ) were constant to within 30% across an upper triangularity scan, while the spreading factor S was lower by up to 50% for NT, indicating a generally lower integral scrape-off layer width, λ int . The line-averaged core density was typically higher for NT discharges for a given fuelling rate, possibly linked to higher particle confinement in NT. Conversely, the divertor neutral pressure and integrated particle fluxes to the targets were typically lower for the same line-averaged density, indicating that NT configurations may be closer to the sheath-limited regime than their PT counterparts, which may explain why NT is more challenging to detach.

Physics↗
DOE OSTI2021

Supporting data for climatic clustering and longitudinal analysis with impacts on food, bioenergy, and pandemics

This data supports the conclusions found in climatic clustering and longitudinal analysis with impacts on food, bioenergy, and pandemics. Included here are (i) the binarized geolocation vectors used for exhaustive vector comparisons, (ii) the resulting climatic networks, (iii) the results of applying Markov clustering to the climatic networks, and (iv) the results of applying Correlation-of-Correlations (cor-cor) to the climatic networks. The set of binarized geolocation vectors that are used as inputs for the Combinatorial Metrics library (CoMet) are of the form comet-UUUUUxVVVVV-XXXX-YYYY.shuffled.tped where UUUUU is the number of vectors, VVVVV is the length of each vector, XXXX is the starting year, and YYYY is the ending year. Each line corresponds to a geolocation vector of binary elements A (i.e., 0) and T (i.e., 1). The set of climatic networks that are used for downstream network analysis are of the form network-U-way-XXXX-YYYY.parsed.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, and YYYY is the ending year. Each line corresponds to an edge linking two geolocations (defined by latitude and longitude) with its corresponding edge weight (i.e., DUO score). The set of cluster results are of the form clusters-U-way-XXXX-YYYY-thresh-VVVV-inflation-WWW.clustered.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, YYYY is the ending year, VVVV is the similarity threshold, and WWW is the Markov clustering inflation rate. Each line corresponds to a single cluster and is composed of a number of corresponding geolocations (defined by latitude and longitude). The set of cor-cor results are of the form corcor-U-way-XXXX-YYYY.cumulative.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, and YYYY is the ending year. Each line corresponds to a single geolocation with it's corresponding cor-cor value.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence K - Raw Data

Sequence K: Step AOA, Probes (P) This sequence was designed to quantify the 3-D blade static angle-of-attack response in the presence of rotational influences by varying the blade pitch angle. Sequence K used an upwind, rigid turbine with a 0° cone angle. The wind speeds ranged from 6 m/s to 20 m/s, and data were collected at yaw angles of 0° and 30°. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. The blade pitch angle ramped continuously at 0.18°/s over a wide range of increasing and decreasing pitch angles. A step sequence was also performed. The blade pitch was stepped 5°, the flow was allowed to stabilize, and the pitch angle was held for 8 seconds. Then the pitch angle step was repeated. Again, a wide range of pitch angles was obtained, both increasing and decreasing. The file lengths for this sequence varied from 96 seconds to 6 minutes, depending on the pitch angle range. Some short points were collected at 0° yaw and 3° pitch to verify the functionality of the instrumentation. The file name convention used the initial letter K, followed by two digits specifying wind speed, followed by two digits for yaw angle, followed by RU, RD, or ST, followed by the repetition digit. The angle-of-attack motion was differentiated by RU (ramp up), RD (ramp down), and ST (step down then step up). This sequence is related to sequences L and R.

17 WIND ENERGY↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence L - Raw Data

Sequence L: Step AOA, Parked (P) This sequence was designed to quantify the 3-D blade static angle-of-attack response in the absence of rotational influences by varying the blade pitch angle. This test sequence used an upwind, rigid turbine with a 0° cone angle. Wind speeds of 20 m/s and 30 m/s were used, and all data were collected at a yaw angle of 0°. The rotor was parked with the instrumented blade fixed at 0° azimuth, and the rotor lock was installed (see Appendix A). Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to -99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. The blade pitch angle ramped continuously at 0.18°/s over a wide range of increasing and decreasing pitch angles. A step sequence was also performed. The blade pitch was stepped 5°, the flow was allowed to stabilize, and the pitch angle was held for 8 seconds. Then the pitch angle step was repeated. Again, a wide range of pitch angles was obtained, both increasing and decreasing. The file lengths for this sequence varied from 5 to 10 minutes, depending on the pitch angle range. The file name convention used the initial letter L followed by two digits specifying wind speed, followed by 00 for yaw angle, followed by RU, RD, or ST, followed by the repetition digit. The angle-of-attack motion was differentiated by RU (ramp up), RD (ramp down), and ST (step down, then step up). This sequence is related to sequences K and R.

17 WIND ENERGY↗
NASA NTRS2008

Non-Destructive Evaluation of Materials via Ultraviolet Spectroscopy

A document discusses the use of ultraviolet spectroscopy and imaging for the non-destructive evaluation of the degree of cure, aging, and other properties of resin-based composite materials. This method can be used in air, and is portable for field use. This method operates in reflectance, absorbance, and luminescence modes. The ultraviolet source is used to illuminate a composite surface of interest. In reflectance mode, the reflected response is acquired via the imaging system or via the spectrometer. The spectra are analyzed for organic compounds (conjugated organics) and inorganic compounds (semiconducting band-edge states; luminescing defect states such as silicates, used as adhesives for composite aerospace applications; and metal oxides commonly used as thermal coating paints on a wide range of spacecraft). The spectra are compared with a database for variation in conjugation, substitution, or length of molecule (in the case of organics) or band edge position (in the case of inorganics). This approach is useful in the understanding of material quality. It lacks the precision in defining the exact chemical structure that is found in other materials analysis techniques, but it is advantageous over methods such as nuclear magnetic resonance, infrared spectroscopy, and chromatography in that it can be used in the field to assess significant changes in chemical structure that may be linked to concerns associated with weaknesses or variations in structural integrity, without disassembly of or destruction to the structure of interest.

Pugel, Betsy↗
DOE OSTI2025

High-precision monitoring of outgassing species in model extreme ultraviolet photoresists with a cavity ring-down spectrometer

Background Extreme ultraviolet (EUV) photoresists play a pivotal role in advancing nanopatterning technologies by balancing image quality and sensitivity. The outgassing behavior of photoresist thin films under EUV and deep ultraviolet (DUV) exposure reveals chemical details relevant to their performance. Aim Here, we focus on utilizing an analytical technique not previously used in photolithography, the tabletop cavity ring-down spectrometer, to investigate outgassing dynamics in EUV photoresists, enabling precise chemical identification and deeper insights into resist processing. Approach The spectrometer’s enhanced laser path length (∼ 20 km) and broadband absorption capabilities in the C–H overtone region allow for sensitive and temporally resolved detection of mixtures of outgassed species. Using a model resist comprising a polymer matrix with a photoacid generator and quencher, we analyzed the influence of time delays between exposure and post-exposure bake (PEB) as well as storage under varying environmental conditions. Results Suppression of isobutylene outgassing and thickness loss was observed with extended delays between exposure and PEB, potentially linked to water absorption and acid deactivation. The technique proved highly effective in distinguishing subtle chemical differences between processing stages. Conclusions Delay times and their environmental conditions, particularly humidity, reduce outgassing and thickness loss of photoresists during PEB, suggesting decreased acid-driven deprotection. This can potentially impact sensitivity, defectivity, and roughness of resist patterns, necessitating precise monitoring and control.

Extreme ultraviolet photoresists↗
DOE OSTI2023

Longitudinal Single‐Cell Imaging of Engineered Strains with Stimulated Raman Scattering to Characterize Heterogeneity in Fatty Acid Production

Abstract Understanding metabolic heterogeneity is critical for optimizing microbial production of valuable chemicals, but requires tools that can quantify metabolites at the single‐cell level over time. Here, longitudinal hyperspectral stimulated Raman scattering (SRS) chemical imaging is developed to directly visualize free fatty acids in engineered Escherichia coli over many cell cycles. Compositional analysis is also developed to estimate the chain length and unsaturation of the fatty acids in living cells. This method reveals substantial heterogeneity in fatty acid production among and within colonies that emerges over the course of many generations. Interestingly, the strains display distinct types of production heterogeneity in an enzyme‐dependent manner. By pairing time‐lapse and SRS imaging, the relationship between growth and production at the single‐cell level are examined. The results demonstrate that cell‐to‐cell production heterogeneity is pervasive and provides a means to link single‐cell and population‐level production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Study of the interplay between lower-order and higher-order energetic strain-gradient effects in polycrystal plasticity

in this report strain-gradient (SG) plasticity refers to a class of non-local theories in which gradients of plastic slip determine the storage of geometrically necessary dislocations, introducing a length-scale dependence in the mechanical behavior of crystalline materials, which is otherwise lacking in local theories. In this work, we incorporate lower-order (LO) and higher-order energetic (HOE) strain-gradient effects into a crystal plasticity fast Fourier transform (FFT)-based formulation to investigate the interplay of the length scale that each strain-gradient term introduces at the microscale, and the mechanical properties that result at the macroscale. For an applicable range of length scales, we consider two systems: a 1-D two-phase face centered cubic (FCC) laminate and a 3-D FCC polycrystal, and two uniaxial deformation modes: monotonic tension and cyclic tension–compression. We show that increases in the individual LO and HOE length scales increase the hardening rate and strength of the material, respectively. When combined, the strong LO hardening is less pronounced than the effect alone due to the lowering of the gradients due to the HOE microstress. We demonstrate that the LO and HOE hardening manifest as “isotropic” (yield surface expansion) and “kinematic” (yield surface shift) effects, respectively, consistent with their theoretical origins. We show that in cyclic loading, the Bauschinger effect emerges in both local and non-local calculations and link its origins and severity to the behavior in the strain field, slip-system rates, and the HOE microforce.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantifying the Impact of Charge Rate and Number of Cycles on Structural Degeneration of Li-Ion Battery Electrodes

A quantitative link between crack evolution in lithium-ion positive electrodes and the degrading performance on cells is not yet well established nor is any single technique capable of doing so widely available. Here, we demonstrate a widely accessible high-throughput approach to quantifying crack evolution within electrodes. The approach applies super-resolution scanning electron microscopy (SEM) imaging of cross-sectioned NMC532 electrodes, followed by segmentation and quantification of crack features. Crack properties such as crack intensity, crack width and length are quantified as a function of charge rate (1C, 6C, and 9C) and cycle number (25, 225, and 600 cycles). Hundreds of particles are characterized for statistical confidence in the quantitative crack measurements. The data on crack evolution is compared to electrochemical data from full cells and half cells with the NMC532 positive electrodes. We show that while crack evolution strongly correlates with capacity fade in the first 25 cycles, it does not correlate well for the following hundreds of cycles indicating that cracking may not be the dominant cause of capacity fade throughout the cycle-life of cells.

25 ENERGY STORAGE↗
DOE OSTI2021

Tidal Energy Resource Characterization, Bottom Lander Measurements, Cook Inlet, AK, 2021

These datasets are from tidal resource characterization measurements collected on the Terrasond High Energy Oceanographic Mooring (THEOM) from 1 July 2021 to 30 August 2021 (60 days) in Cook Inlet, Alaska. The lander was deployed at 60.7207031 N, 151.4294998 W in ~50 m of water. The dataset contains raw and processed data from the following two instruments: 1. A Nortek Signature 500 kHz acoustic Doppler current profiler (ADCP). Data were recorded in 4 Hz in the beam coordinate system from all 5 beams. Processed data has been averaged into 5 minutes bins and converted to the East-North-Up (ENU) coordinate system. 2. A Nortek Vector acoustic Doppler velocimeter (ADV). Data were recorded at 8 Hz in the beam coordinate system. Processed data has been averaged into 5 minutes bins and converted to the Streamwise - Cross-stream - Vertical (Principal) coordinate system. Turbulence statistics were calculated from 5-minute bins, with an FFT length equal to the bin length, and saved in the processed dataset. Data was read and analyzed using the DOLfYN (version 1.0.2) python package and saved in MATLAB (.mat) and netCDF (.nc) file formats. Files containing analyzed data (".b1") were standardized using the TSDAT (version 0.4.2) python package. NetCDF files can be opened using DOLfYN (e.g., `dat = dolfyn.load(''*.nc")`) or the xarray python package (e.g. `dat = xarray.open_dataset("*.nc"). All distances are in meters (e.g., depth, range, etc), and all velocities in m/s. See the DOLfYN documentation linked in the submission, and/or the Nortek documentation for additional details.

16 TIDAL AND WAVE POWER↗
NASA NTRS1992

All-YBa2Cu3O(7-x) edge-geometry weak links

High quality YBa2Cu3O(7-x)/normal-metal/YBa2Cu3O(7-x) edge-geometry weak links are fabricated using nonsuperconducting Y-Ba-Cu-O barrier layers deposited by laser ablation at reduced growth temperatures. Devices incorporating 25-100-A-thick barrier layers exhibit current-voltage characteristics consistent with the resistively-shunted-junction model, as well as ac Josephson steps. Magnetic field modulation of the critical currents shows Fraunhofer-like behavior with a periodicity which scales with device area. The critical currents vary exponentially with barrier thickness indicating an effective normal metal coherence length of 20 A. The average resistances scale linearly with Y-Ba-Cu-O interlayer thickness and device area. The scaling behavior of the device parameters combined with the well-behaved magnetic field modulation of the critical currents demonstrates good barrier-layer uniformity with low pinhole densities. Near the transition temperature, the critical currents exhibit a temperature dependence proportional to (1 - T/Tc) squared.

Hunt, B. D.↗
NASA NTRSDate not supplied

ISRU: Using Biology to Produce Food and Oxygen from Resources on Mars

Any crewed mission to Mars is a “biological” mission. As we move farther away from Earth, we will have to produce the required food, water and nutrient resources to sustain the crew in route or on the surface of other planetary bodies. Critical nutrients, like vitamins, have been shown to degrade in our current food system and represent a risk to long term crew health. One way to address this problem is by developing reliable Biological Life Support Systems (BLSS) that can provide fresh, nutrient-rich foods. Much work in this area will be done as we learn to live and work on the Moon. Systems developed for the Moon should also work on Mars, but will not be designed to take advantage of resources that Mars offers: CO2, more abundant water, and a day length similar to Earth’s. The photosynthetic portion of a BLSS can act as an ISRU element on Mars by providing human life support needs. There is an urgent need to understand how to build components of a fully functional BLSS. One Mars Exploration Program Analysis Group (MEPAG) goal relates to this area.

B. M. Link↗
DOE OSTI2022

Structural basis of colibactin activation by the ClbP peptidase

Abstract Colibactin, a DNA cross-linking agent produced by gut bacteria, is implicated in colorectal cancer. Its biosynthesis uses a prodrug resistance mechanism: a non-toxic precursor assembled in the cytoplasm is activated after export to the periplasm. This activation is mediated by ClbP, an inner-membrane peptidase with an N-terminal periplasmic catalytic domain and a C-terminal three-helix transmembrane domain. Although the transmembrane domain is required for colibactin activation, its role in catalysis is unclear. Our structure of full-length ClbP bound to a product analog reveals an interdomain interface important for substrate binding and enzyme stability and interactions that explain the selectivity of ClbP for the N -acyl- d -asparagine prodrug motif. Based on structural and biochemical evidence, we propose that ClbP dimerizes to form an extended substrate-binding site that can accommodate a pseudodimeric precolibactin with its two terminal prodrug motifs in the two ClbP active sites, thus enabling the coordinated activation of both electrophilic warheads.

Biochemistry & Molecular Biology↗