Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microscope and microscopy.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

Effect of Ca and Sm Combined Addition on the Microstructure and Elevated-Temperature Mechanical Properties of Mg-6Al Alloys

In the present study, the microstructure and elevated-temperature mechanical properties of Mg-6Al, Mg-6Al-4Ca, Mg-6Al-4Sm and Mg-6Al-2Ca-2Sm alloys were investigated. The experimental results showed that the microstructure and elevated-temperature mechanical property of Mg-6Al alloy changed obviously with the different elements addition. By analyzing the results of optical microscope, x-ray diffraction analysis, scanning electron microscope, and transmission electron microscope, it could be determined that there was only Mg{sub 17}Al{sub 12} phase in Mg-6Al alloy, there were Al{sub 2}Ca and (Mg, Al){sub 2}Ca phases in Mg-6Al-4Ca alloy, there were Al{sub 2}Sm and Mg{sub 17}Al{sub 12} phases in Mg-6Al-4Sm alloy, and there were (Mg, Al){sub 2}Ca, Al{sub 2}Ca and Al{sub 2}Sm phases in Mg-6Al-2Ca-2Sm alloy. In addition, the addition of alloying elements including Ca and Sm, especially the composite addition, could significantly improve the tensile properties of Mg-6Al alloy. Compared to Mg-6Al alloy, the tensile strengths of Mg-6Al-2Ca-2Sm alloy at 448, 473 and 498 K were enhanced by 50.32, 87.92, and 94.99%, respectively. Furthermore, when the stretching temperatures were 448 and 473 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the mixture of intergranular fracture and trans-crystalline fracture. However, when the stretching temperature was 498 K, the fracture pattern of Mg-6Al-2Ca-2Sm alloy was the intergranular fracture.

36 MATERIALS SCIENCE↗

Effects of Bi-Sb Addition and Solution Treatment on Microstructures and Mechanical Properties of Al-20 wt.% Mg{sub 2}Si Composites

In this study, the effects of compound modification with Bi and Sb and solution treatment on the microstructures evolution and the mechanical properties of Al-20 wt.% Mg{sub 2}Si composites were investigated. The specimens were observed by optical microscope, scanning electron microscope equipped with an energy-dispersive spectrometer and x-ray diffraction. The characterization results showed that 2.0 wt.% Sb and 0.2 wt.% Bi addition refined the primary Mg{sub 2}Si from 95 to 10 μm, accompanied by a change in morphology from coarse dendrites to dispersive fine polygons. After solution treatment at 540 °C for 15 h, the sharp polygonal primary Mg{sub 2}Si particles were blunted and the flake-like eutectic Mg{sub 2}Si phases were changed to small spherical particles, resulting in the increase in the Brinell hardness of the composites from HB 94.53 to 134.67. Mechanical tests revealed that both tensile strength and hardness of the composite were improved by compound modification with Bi and Sb, and the ultimate tensile strength (UTS) was increased from 216 MPa unmodified to 257 MPa with optimum modification of 2 wt.% Sb and 0.2 wt.% Bi. A propounded change in hardness from HB 94.53 to 130.67 was also investigated.

36 MATERIALS SCIENCE↗

A Study on the Microstructures and Properties of Selective Laser Melted Babbitt Metals

Babbitt metal cubes were prepared by means of selected laser melting (SLM) process using Sn—11% Sb—6% Cu alloy powders; their microstructures were studied using optical microscope (OM), SEM, EDS, XRD and DSC; and their mechanical properties were tested using Vickers hardness and tensile methods. The results show that fully dense Babbitt metal components can be prepared by using appropriate SLM process parameters and an interlayer staggered laser scanning strategy. Anisotropy characteristics appear in both the microstructure and mechanical properties of SLM-Babbitt cubic specimens. The average hardness was in the range of 32.5 HV0.05 to 35.3 HV0.05. Both tensile strength and elongation were somewhat higher in a direction parallel to the laser scanning speed (Y axis) than in a direction perpendicular to the laser scanning speed (X axis). The strengthening mechanism is suggested to include solid solution strengthening of oversaturated Sb in the Sn matrix, as well as dispersion strengthening of finely dispersed SnSb and Cu{sub 6}Sn{sub 5} particles. The overgrown acicular Cu{sub 6}Sn{sub 5} phases at low laser scanning speeds and void formation at higher laser scanning speeds seriously deteriorate the mechanical properties of the SLM-Babbitt specimens.

36 MATERIALS SCIENCE↗

Microstructural Development and Mechanical Properties of Friction Stir Welded Ferritic Stainless Steel AISI 409

This work investigates the effect of friction stir welding process parameters (rotation rate and traverse speed) on the microstructural evolution of friction stir welded (FSWed) ferritic stainless steel (FSS) AISI 409. Optical microscope, scanning electron microscope and electron backscattering diffraction are used to quantitatively assess the development in grain structure and texture. The microstructural development suggested that thermo-mechanical deformation occurs in the stir zone within the austenite/ferrite phase region, ultimately transforming upon cooling into bainitic/ferritic microstructure. The fraction and size of the bainitic/ferritic grains are found to vary through the thickness of the joints. High fractions of coarse ferritic grains are found near the top of the stir zone, and low fraction of fine ferritic grains is found near the bottom of the stir zone. This bainitic/ferritic grain structure resulted in an increase in the hardness of the stir zone by about 74% relative to the base material. The tensile strength of the FSWed FSS joints is almost at the same level of the base material with reduction in the ductility as a result of the increased hardness of the weld zone.

36 MATERIALS SCIENCE↗

Structural, Mechanical, and Electrical Behavior of Ceramic-Reinforced Copper Metal Matrix Hybrid Composites

This article presents the structural, mechanical, and electrical behavior of ceramic-reinforced copper metal matrix hybrid composites developed by stir-casting technique. Commercial copper was used as matrix, and different weight percentages of boron carbide (B{sub 4}C), with constant weight percentage of tungsten carbide, boron nitride, and chromium, were used as reinforcements. Copper hybrid composites were characterized by high-resolution x-ray diffraction, optical microscope, scanning electron microscope, energy-dispersive analysis of x-ray, high-resolution scanning electron microscope, and Fourier transform infrared spectroscopy. Density, hardness, tensile strength, compressive strength, and electrical conductivity were also analyzed. These hybrid composites show improved mechanical properties such as hardness, tensile strength, and compressive strength, while relatively lower density and electrical conductivity were observed.

36 MATERIALS SCIENCE↗

A reactive wetting strategy improves lithium metal reversibility

The cycling of lithium metal (Li 0 ) anode is often accompanied by irregular lithium plating/stripping, leading to poor Li 0 reversibility, and posing a grand challenge to constructing reliable Li 0 batteries. Hereby, we report a reactive wetting strategy to enable conformal and highly reversible Li 0 plating/stripping through a lithium-reactive substrate. In this study, the reactive wetting, smooth nucleation, and conformal growth behaviors of Li 0 are visualized through in-situ transmission electron microscopy, ex-situ scanning electron microscope, and in-situ optical microscope characterizations. Based on the reactive wetting substrate, high average Coulombic efficiencies (99.0% at 0.5 mA cm -2 for 400 cycles) are realized for Li 0 anodes. By pre-plating Li 0 into the reactive wetting substrate as anodes and leveraging LiFePO 4 as cathodes, high capacity retention (76.0% after 200 cycles in low N/P ratio conditions) is also achieved in the as-constructed Li 0 full cells. This work establishes a fundamental understanding of reactive wetting dynamics of Li 0 and provides a drop-in solution to improving Li 0 reversibility.

25 ENERGY STORAGE↗

Nonequilibrium spherulitic magnetite in the Ryugu samples

Here, we have investigated several particles collected during each of two touchdowns of the Hayabusa2 spacecraft at the surface of the C-type asteroid 162173 Ryugu using various electron microscope techniques. Our detailed transmission electron microscopy study shows the presence of magnetite with various morphologies coexisting in close proximity. This is characteristic of CI chondrite-like materials and consistent with the mineral assemblages and compositions in the Ryugu parent body. We describe the microstructural characteristics of magnetite with different morphologies, which could have resulted from the chemical conditions (growth vs. diffusion rate) during their formation. Furthermore, we describe the presence of magnetites with a spherulitic structure composed of individual radiating fibers that are characterized by pervasive, homogeneously distributed euhedral to subhedral pores that have not been described in previous chondrite studies. This particular spherulitic structure is consistent with crystallization under nonequilibrium conditions. Additionally, the presence of a high density of defects within the magnetite fibers, the high surface/volume ratio of this morphology, and the presence of amorphous materials in several pores and at the edges of the acicular fibers further support their formation under nonequilibrium conditions. We suggest that the growth processes that lead to this structure result from the solution reaching a supersaturated state, resulting in an adjustment to a lower free energy condition via nucleation and rapid growth.

58 GEOSCIENCES↗

Growth kinetics of Al–Fe intermetallic compounds during annealing treatment of friction stir lap welds

In this study, we explored the growth kinetics of the Al–Fe intermetallic (IM) layer at the joint interface of the St-12/Al-5083 friction stir lap welds during post-weld annealing treatment at 350, 400 and 450 °C for 30 to 180 min. Optical microscope (OM), field emission gun scanning electron microscope (FEG-SEM) and transmission electron microscope (TEM) were employed to investigate the structure of the weld zone. The thickness and composition of the IM layers were evaluated using image analysis system and electron back-scatter diffraction (EBSD), respectively. Moreover, kernel average misorientation (KAM) analysis was performed to evaluate the level of stored energy in the as-welded state. The results showed that the growth kinetics of the IM layer was not governed by a parabolic diffusion law. Presence of the IM compounds as well as high stored energy near the joint interface of the as-welded sample was recognized to be the origin of the observed deviation from the parabolic diffusion law. - Highlights: • This work provided a new insight into growth kinetics of Al–Fe IM thickness. • The growth kinetics of IM layer was not governed by a parabolic diffusion law. • IM near the joint interface was the origin of deviation from the parabolic law. • High stored energy at joint interface was origin of deviation from parabolic law.

36 MATERIALS SCIENCE↗

Microstructure, mechanical properties and microtexture of friction stir welded S690QL high yield steel

Two try-out campaigns of friction stir welding (FSW) were performed with different friction parameters to join S690QL high yield strength steel. The welds were investigated at macroscopic and microscopic scales using optical and electronic microscopy and microhardness mapping. Welds of the second campaign exhibit microstructures and mechanical properties in accordance with requirements for service use. Microtexture measurements were carried out in different zones of welds by electron backscattered diffraction (EBSD). It is shown that that texture of the bottom of the weld is similar to that of the base metal, suggesting a diffusion bonding mechanism. Finally, the mechanical properties (tensile strength, resilience, bending) were established on the most promising welds. It is shown that it is possible to weld this high yield strength steel using FSW process with satisfactory geometric, microstructural and mechanical properties. - Highlights: •1000 mm ∗ 400 mm ∗ 8 mm S690QL steel plates are joined by friction stir welding (FSW). •Maximum hardness is reduced by optimization of process parameters. •Various microstructures are formed but no martensite after process optimization. •Texture is modified in mechanically affected zones of the weld. •Texture in the bottom of the weld is preserved, suggesting diffusion bonding.

36 MATERIALS SCIENCE↗

Microstructure of a safe-end dissimilar metal weld joint (SA508-52-316L) prepared by narrow-gap GTAW

The microstructure, residual strain and interfacial chemical composition distribution of a safe-end dissimilar metal weld joint (DMWJ, SA508-52-316L) prepared by narrow-gap gas-tungsten arc welding (NG-GTAW) were studied by optical microscope (OM) and scanning electron microscope equipped with an energy dispersive X-ray microanalysis (SEM/EDX) and an electron back scattering diffraction (EBSD) system. Complex microstructure and chemical composition distribution are found, especially at the SA508-52 interface and the 52-316L interface. In brief, a complicated microstructure transition exists within the SA508 heat affected zone (HAZ); the residual strain, the fraction of high angle random grain boundaries and low angle boundaries decrease with increasing the distance from the fusion boundary in 316L HAZ; neither typical type II boundary nor obvious carbon-depleted zone is found near the SA508-52 interface; dramatic and complicated changes of the contents of the main elements, Fe, Cr and Ni, are observed at the distinct interfaces, especially at the SA508-52 interface. No carbon concentration is found at the SA508-52 interface. - Highlights: •Residual strain and GBCD change as a function of the distance from FB in 316L HAZ. •Neither type II boundary nor obvious carbon-depleted zone is found in SA508 HAZ. •No carbon concentration is found at the SA508-52 interface. •The middle part of the DMWJ has the highest residual strain.

36 MATERIALS SCIENCE↗

Microstructural characteristics of σ phase and P phase in Ru-containing single crystal superalloys

Microstructural instability caused by topologically close-packed (TCP) phase precipitation restricts the useful compositional range of advanced Ni-base single crystal superalloys in industrial applications. Limited systematic investigations of TCP formers (Cr and Mo) additions on microstructural evolution of both the σ phase and the P phase in Ru-containing single crystal superalloys have been reported. In this study, the microstructural characteristics of σ phase and P phase were investigated in three Ru-containing superalloys with different levels of Cr and Mo additions at 950 °C and 1100 °C by using phase extraction, X-ray diffraction, scanning electron microscope and high resolution transmission electron microscopy. The experimental results indicated that the high level additions of Cr and Mo promoted the formation of σ phase and P phase, respectively. The amount of σ phase was much higher than that of P phase after long term exposure at 950 °C and 1100 °C. The sheet-like σ phase existed in the alloy with higher Cr addition after thermal exposure at 950 °C and 1100 °C for 1000 h, while the needle-like P phase precipitated in high Mo content alloy after thermal exposure at 1100 °C for 1000 h and the intergrowth of σ phase and P phase was observed after thermal exposure at 950 °C for 500 h. Both the σ phase and P phase were enriched in Re, W, Cr and Mo, but the σ phase contained more Re and Cr while the P phase contained more Mo and Ni, and Ru was found in both phases. The nucleation of σ phase was much easier than P phase due to the more ledge steps in the interfacial structure between σ phase and matrix, as well as the higher partitioning ratios of Re, Cr and Mo. This study is helpful to understand the microstructural evolution of σ phase and P phase, and to optimize the alloy design in Ru-containing superalloys. - Highlights: •Microstructures of σ phase and P phase were characterized in detail. •Cr and Mo influenced the precipitation of σ phase and P phase, respectively. •Partitioning ratios and interfacial relationship decided precipitation behaviors.

36 MATERIALS SCIENCE↗

Austenite and precipitation in secondary-hardening ultra-high-strength stainless steel

Highlights: • Austenite and precipitation in Ferrium S53 steel were analyzed. • Austenite decreased to less than 5% after cryogenic treatment and tempering. • M{sub 2}C carbide could segregate inside martensite lath or in the larger parallel microstructure. - Abstract: Ferrium S53 is a new secondary-hardening ultra-high-strength stainless steel, with more Cr than other Co-Ni ultra-high-strength steels. Austenite has a great effect on the fracture toughness of this metal, and the carbides that are precipitated are the main strengthening phase of Ferrium S53 steel; in this study, its microstructural changes during heat treatment were observed and analyzed by X-ray diffraction (XRD), Optical microscope (OM), SEM, and transmission electron microscopy (TEM). About 40.85% retained austenite in the quenched sample is decreased to less than 5% after cryogenic treatment and tempering. In the final sample, block austenite is retained austenite, and film austenite around 5 nm in width is reverted austenite. Inside the martensite lath, parallel twin-like structures are actually segregated M{sub 2}C precipitates, and most of them are smaller than 20 nm. These precipitates can be aggregated into a several-micron-long parallel zonal microstructure.

36 MATERIALS SCIENCE↗

Synthesis of mesoporous silica materials (MCM-41) from iron ore tailings

Highly ordered mesoporous materials were successfully synthesized by using the iron ore tailings as the silica source and n-hexadecyltrimethyl ammonium bromide as the template. The samples were detail characterized by powder X-ray diffraction, scanning electron microscope, high-resolution transmission electron microscopy and N{sub 2} physisorption. The as-synthesized materials had high surface area of 527 m{sup 2} g{sup -1} and the mean pore diameter of 2.65 nm with a well-ordered two-dimensional hexagonal structure. It is feasible to prepare mesoporous MCM-41 materials using the iron ore tailings as precursor.

36 MATERIALS SCIENCE↗

Fabrication of hollow mesoporous NiO hexagonal microspheres via hydrothermal process in ionic liquid

Highlights: Black-Right-Pointing-Pointer Ni(OH){sub 2} precursors were synthesized in ionic liquid and water solution by hydrothermal method. Black-Right-Pointing-Pointer NiO hollow microspheres were prepared by thermal treatment of Ni(OH){sub 2} precursors. Black-Right-Pointing-Pointer NiO hollow microspheres were self-assembled by mesoporous cubic and hexagonal nanocrystals with high specific surface area. Black-Right-Pointing-Pointer The mesoporous structure is stable at 773 K. Black-Right-Pointing-Pointer The ionic liquid absorbed on the O-terminate surface of the crystals to form hydrogen bond and played key roles in determining the final shape of the NiO novel microstructure. -- Abstract: The novel NiO hexagonal hollow microspheres have been successfully prepared by annealing Ni(OH){sub 2}, which was synthesized via an ionic liquid-assisted hydrothermal method. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), N{sub 2} adsorption-desorption and Fourier transform infrared spectrometer (FTIR). The results show that the hollow NiO microstructures are self-organized by mesoporous cubic and hexagonal nanocrystals. The mesoporous structure possessed good thermal stability and high specific surface area (ca. 83 m{sup 2}/g). The ionic liquid 1-butyl-3methylimidazolium tetrafluoroborate ([Bmim][BF{sub 4}]) was found to play a key role in controlling the morphology of NiO microstructures during the hydrothermal process. The special hollow mesoporous architectures will have potential applications in many fields, such as catalysts, absorbents, sensors, drug-delivery carriers, acoustic insulators and supercapacitors.

36 MATERIALS SCIENCE↗

MoS{sub 2} nanosheet functionalized with Cu nanoparticles and its application for glucose detection

Graphical abstract: - Highlights: • First report on decorating MoS{sub 2} nanosheet with Cu nanoparticles by chemical reduction. • Cu nanoparticles were uniformly decorated on MoS{sub 2} nanosheet. • Glucose biosensor based on copper nanoparticles-MoS{sub 2} nanosheet hybrid is fabricated. • The biosensor exhibits high sensitivity. - Abstract: For the first time, Cu nanoparticles were evenly decorated on MoS{sub 2} nanosheet by chemical reduction. The as-prepared Cu-MoS{sub 2} hybrid was characterized by atomic force microscope (AFM), Raman spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and then used to fabricate a non-enzymatic glucose sensor. The performance of our sensor was investigated by cyclic voltammetry and amperometric measurement in alkaline media. Electrochemical tests showed that Cu-MoS{sub 2} hybrid exhibited synergistic electrocatalytic activity on the oxidation of glucose with a high sensitivity of 1055 μA mM{sup −1} cm{sup −2} and a linear range up to 4 mM.

36 MATERIALS SCIENCE↗

Thermal Conversion of Ultrathin Nickel Hydroxide for Wide Band Gap 2D Nickel Oxides

Wide band gap (WBG) semiconductors (E g > 2.0 eV) are integral to the advancement of next-generation electronics, optoelectronics, and power industries owing to their capability for high-temperature operation, high breakdown voltage, and efficient light emission. Enhanced power efficiency and functional performance can be attained through miniaturization, specifically via the integration of device fabrication into a two-dimensional (2D) structure enabled by WBG 2D semiconductors. However, as an essential subgroup of WBG semiconductors, 2D transition metal oxides (TMOs) remain largely underexplored in terms of physical properties and applications in 2D optoelectronic devices, primarily due to the scarcity of sufficiently large 2D crystals. Thus, our goal is to develop synthesis pathways for 2D TMOs possessing large crystal domains (e.g., >10 μm), expanding the 2D TMO family and providing insights for future engineering of 2D TMOs. Here, we demonstrate the synthesis of WBG 2D nickel oxide (NiO) (E g > 2.7 eV) thermally converted from 2D nickel hydroxide (Ni(OH) 2 ) with a lateral domain size larger than 10 μm. Moreover, the conversion process is investigated using various microscopic techniques, such as atomic force microscopy, Raman spectroscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy, providing significant insights into morphology and structural variations under different oxidative conditions. The electronic structure of the converted Ni x O y is further investigated using multiple soft X-ray spectroscopies, such as X-ray absorption and emission spectroscopies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ electron microscopy: atomic-scale dynamics of metal oxidation and corrosion

Corrosion degrades metals through complex microscopic processes that traditional methods often fail to capture. In-situ transmission electron microscopy (TEM) bridges this gap by providing real-time atomic-scale imaging of oxidation and corrosion dynamics. Gas-phase TEM uncovers critical oxidation mechanisms like oxide nucleation and alloying effects, while liquid-phase TEM tracks corrosion initiation. Coupled with emerging techniques like ultrafast direct electron detection cameras, these advancements promise unprecedented resolution in understanding material degradation.

36 MATERIALS SCIENCE↗

Thickness dependent structural, optical and electrical properties of CuIn{sub 0.8}Ga{sub 0.2}Se{sub 2} thin films deposited by pulsed laser deposition

CuIn{sub 0.8}Ga{sub 0.2}Se{sub 2} (CIGS) polycrystalline thin films have been deposited on soda lime glass substrate at different deposition time by pulsed laser deposition. The effect of thickness on structural, surface morphological, optical and electrical properties of thin films were investigated by X-ray diffractometer (XRD), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), UV-Vis-NIR spectrophotometer and electrical measurement unit. XRD study reveals that all deposited films are polycrystalline in nature and have tetragonal phase of CIGS. Crystallinity of CIGS films has been found to improve with increase in thickness of CIGS films as evidenced by sharp XRD peaks for (112) orientation. Grain size and rms surface roughness of CIGS films have been found to be increased with increase in thickness. All the deposited CIGS films exhibit direct band gap semiconducting behaviour with ∼10{sup 6} cm{sup −1} absorption co-efficient. Optical band gap and resistivity of CIGS films have been found to decrease with increase in thickness.

36 MATERIALS SCIENCE↗