Results for “Optimal matching” — Page 24

NASA NTRS2023

Finite Element Model Tuning using Analytical Sensitivity Values

This paper presents an efficient approach for tuning finite element models to match the measured ground vibrationtest and proof test data. Frequencies, mode shapes, total weight, location of the center of gravity, and staticdeformation computed from the finite element model are matched to the measured data. The model tuningprocedure used in this work is based on solving an optimization problem in which the errors for the consideredmetrics, between the finite element prediction and the measured data, are minimized. Analytical sensitivity values ofperformance indices are computed using the NASTRAN-generated sensitivity values together with the in-housecomputer programs, which allow for faster computational time and the use of gradient-based optimizers. The methodis applied to the Aerostructures Test Wing 4 model. The study shows that the military standard and the NASAstandard for comparing analytical and experimental modal data are all satisfied. The final finite element modelcorrelates well with the test data. The flutter speed decreases by 8.91% after model tuning compared with the original Aerostructures Test Wing 4 design.

Chan-gi Pak↗

NASA NTRSDate not supplied

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

multidisciplinary optimization↗

DOE OSTI2023

Optimal PMU design based on sampling model and sensitivity analysis

The precise measurements of the synchrophasor and frequency from phasor measurement units (PMUs) are widely used in power grid applications. With the improvement of the technique, applications always require stable dynamic performance and higher accuracy for the synchrophasor and frequency measurements, which is challenging for PMU development. To evaluate the contribution of PMU hardware to measurement accuracy, this paper proposes a general-purpose sampling model to analyze the measurement error. In the proposed sampling model, a strict mathematical derivation is derived, where its error is purely determined by the parameters of the PMU hardware. The sensitivity analysis is carried out by three methods, including mathematical analysis, computer simulation, and variance-based sensitivity analysis. Through the sensitivity analysis, this paper establishes the systematic formulation and the inclusion of synchrophasor, frequency, and ROCOF. Experimental results based on the real-world testbench involving distribution-level PMUs match the mathematical analysis conclusion, which verifies the correctness of the general-purpose sampling model. Furthermore, a strategy for the optimal PMU design is proposed, which could guide PMU design in the future.

42 ENGINEERING↗

DOE OSTI2021

Development of a Vibration Technique Based on Geometric Optimization for Fatigue Life Evaluation of Sandwich Composite Structures

A major obstacle to obtaining cost-effective experimental data on the fatigue life of sandwich panels is the prohibitive amount of time and cost required to carry out millions of cycles. On the other hand, vibration techniques applied to sandwich geometries fail to match the stress patterns that are obtained from standard flexural fatigue tests. To overcome such limitations, a vibration-based fatigue technique is proposed, which entails the use of sandwich specimens whose geometries are optimized to reproduce the stress distribution observed during three point bend loading while vibrating at the first resonant frequency. The proposed vibration technique was experimentally validated. The results, compared with the average number of cycles to failure at different stress ratios obtained via the Three-Point Bending test, showed high levels of accuracy. The proposed method is robust and time effective and indicates the possibility of attaining fatigue lifetime prediction of a wide class of composite elements, such as sandwich panels.

36 MATERIALS SCIENCE↗

NASA NTRS2021

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

low-boom supersonic transports↗

NASA NTRS2007

High Fidelity Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Results

Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer, and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronie response provides a bridge between electrically heated testing and fueled nuclear testing, providing a better assessment of system integration issues, characterization of integrated system response times and response characteristics, and assessment of potential design improvements' at a relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design can developed. Test results presented in this paper correspond to a "first cut" simulator design for a potential liquid metal (NaK) cooled reactor design that could be applied for Lunar surface power. Proposed refinements to this simulator design are also presented.

Bragg-Sitton, Shannon M.↗

NASA NTRS2007

High Fidelity, Fuel-Like Thermal Simulators for Non-Nuclear Testing: Analysis and Initial Test Results

Non-nuclear testing can be a valuable tool in the development of a space nuclear power system, providing system characterization data and allowing one to work through various fabrication, assembly and integration issues without the cost and time associated with a full ground nuclear test. In a non-nuclear test bed, electric heaters are used to simulate the heat from nuclear fuel. Testing with non-optimized heater elements allows one to assess thermal, heat transfer. and stress related attributes of a given system, but fails to demonstrate the dynamic response that would be present in an integrated, fueled reactor system. High fidelity thermal simulators that match both the static and the dynamic fuel pin performance that would be observed in an operating, fueled nuclear reactor can vastly increase the value of non-nuclear test results. With optimized simulators, the integration of thermal hydraulic hardware tests with simulated neutronic response provides a bridge between electrically heated testing and fueled nuclear testing. By implementing a neutronic response model to simulate the dynamic response that would be expected in a fueled reactor system, one can better understand system integration issues, characterize integrated system response times and response characteristics and assess potential design improvements at relatively small fiscal investment. Initial conceptual thermal simulator designs are determined by simple one-dimensional analysis at a single axial location and at steady state conditions; feasible concepts are then input into a detailed three-dimensional model for comparison to expected fuel pin performance. Static and dynamic fuel pin performance for a proposed reactor design is determined using SINDA/FLUINT thermal analysis software, and comparison is made between the expected nuclear performance and the performance of conceptual thermal simulator designs. Through a series of iterative analyses, a conceptual high fidelity design is developed: this is followed by engineering design, fabrication, and testing to validate the overall design process. Test results presented in this paper correspond to a "first cut" simulator design for a potential liquid metal (NaK) cooled reactor design that could be applied for Lunar surface power. Proposed refinements to this simulator design are also presented.

Bragg-Sitton, Shannon M.↗

NASA NTRS1995

Adaptive Optimization of Aircraft Engine Performance Using Neural Networks

Preliminary results are presented on the development of an adaptive neural network based control algorithm to enhance aircraft engine performance. This work builds upon a previous National Aeronautics and Space Administration (NASA) effort known as Performance Seeking Control (PSC). PSC is an adaptive control algorithm which contains a model of the aircraft's propulsion system which is updated on-line to match the operation of the aircraft's actual propulsion system. Information from the on-line model is used to adapt the control system during flight to allow optimal operation of the aircraft's propulsion system (inlet, engine, and nozzle) to improve aircraft engine performance without compromising reliability or operability. Performance Seeking Control has been shown to yield reductions in fuel flow, increases in thrust, and reductions in engine fan turbine inlet temperature. The neural network based adaptive control, like PSC, will contain a model of the propulsion system which will be used to calculate optimal control commands on-line. Hopes are that it will be able to provide some additional benefits above and beyond those of PSC. The PSC algorithm is computationally intensive, it is valid only at near steady-state flight conditions, and it has no way to adapt or learn on-line. These issues are being addressed in the development of the optimal neural controller. Specialized neural network processing hardware is being developed to run the software, the algorithm will be valid at steady-state and transient conditions, and will take advantage of the on-line learning capability of neural networks. Future plans include testing the neural network software and hardware prototype against an aircraft engine simulation. In this paper, the proposed neural network software and hardware is described and preliminary neural network training results are presented.

Simon, Donald L.↗

NASA NTRSDate not supplied

Integration of Low-Fidelity MDO and CFD-Based Redesign of Low-Boom Supersonic Transports

A mixed-fidelity low-boom multidisciplinary optimization (MDO) problem is formulated for integration of low-fidelity MDO and computational fluid dynamics (CFD) based low-boom inverse design optimization. The mixed-fidelity low-boom MDO problem aims to enforce the weight consistency for CFD-based low-boom inverse design optimization: the optimum low-boom configuration is designed for the weight at the start of cruise of the same configuration for the low-boom overland mission. Moreover, it also seeks the optimum trades among the maximum takeoff gross weight (MTOGW), cruise Mach, and range for the low-boom overland mission while meeting the requirement of flying a transatlantic overwater mission. A block coordinate optimization (BCO) method is developed to find an approximate solution of the mixed-fidelity low-boom MDO problem. The BCO method is successfully applied to generate two CFD-based low-boom configurations that closely match two reversed equivalent area targets with ground noise levels below 70 PLdB, respectively. Moreover, these CFD-based low-boom configurations can be obtained with minor wing modifications from the solutions of the low-fidelity MDO problem. The low-fidelity MDO solutions are Pareto points for constrained multiobjective optimization of MTOGW, low-boom cruise Mach, and low-boom range. The best low-boom concept has a predetermined fuselage shape tailored for passengers and main gear storage, carries 40 passengers at seat pitch of 48 in, flies a low-boom overland mission with cruise Mach of 1.8 and range of 2,950 nm, cruises overwater at Mach 1.8 with range of 3,600 nm, satisfies the specified constraints for landing/cruise/takeoff, has MTOGW of 145,164 lb, trims the low-boom cruise flight with fuel redistributions instead of control surface deflections, and has a reversed equivalent area distribution closely matching a target with ground noise level below 70 PLdB.

low-boom supersonic transports↗

DOE OSTI2021

Analysis and prediction of reaction kinetics using the degree of rate control

“Degree of rate control” (DRC) analysis provides a quantitative approach for analysing the kinetics of multi-step reaction mechanisms that has been widely applied to both heterogeneous and homogeneous catalysis research, as well as electrocatalysis. The DRC of any given transition state or intermediate is defined as a partial derivative such that it approximately equals the fractional increase in net rate to the product of interest per differential decrease in its standard-state free energy for that species (÷RT), holding constant the standard-state free energies of all other transition states and intermediates. Even very complex mechanisms usually have only a few species with non-zero DRCs and are thus the species whose interactions with the catalyst most strongly affect the net rate. These key DRC values thus offer a simple and intuitive route to optimize catalyst materials, especially with the assistance of computational methods like density functional theory (DFT). These high-DRC species are also the species whose energetics must be most accurately measured or calculated to achieve an accurate kinetic model for any reaction mechanism. In simple cases with a single “rate-determining step”, the DRC for its transition state (TS) is + 1. Catalyst-bound intermediates, on the other hand, often have negative DRCs equal to a small integer times their fractional occupancy of catalyst sites. The apparent activation energy equals a weighted average of the standard-state enthalpies (relative to reactants) of all the species (intermediates, transition states and products) in the reaction mechanism, each weighted by its DRC (+RT). It has been shown that the apparent transfer coefficient in electrocatalysis, an inverted form of the Tafel slope, is a weighted average of the number of electrons transferred to generate each intermediate or product species in the mechanism, weighted again by the DRC. Quantitative analysis of kinetic isotope effects (KIEs, or the ratio of net rates for different reactant isotopes) in complex mechanisms has shown that the logarithm of the KIE equals the weighted average over all species in the mechanism of the difference between the two isotopes in their standard-state free energies (÷RT), again weighted by the DRC. The reaction orders with respect to fluid-phase concentrations of reactants, products and intermediates have also been proven to be directly related to DRCs. Thus, there are numerous experimental observables which equate to short linear combinations of DRCs, so that combinations of experimental measurements might provide access to DRC values. Since its invention for transition states in 1994 and its generalization to include intermediates in 2009, the DRC has thus far mainly been calculated for microkinetic models based either entirely on DFT or on DFT with the key energies (i.e., those for high-DRC species) being fine-tuned to match experiments. The relationships summarized in this work provide new opportunities for using experiments earlier in the development and optimization of microkinetic models that require input from computational catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Coupling of electroelastic dynamics and direct contact ultrasonic drying formulation for annular piezoelectric bimorph transducers

A newly developed technique for drying clothes without thermal energy has been developed through the utilization of ultrasonic vibrations from piezoelectric transducers. The novel technique incorporates the actuation of a thin stainless steel disk in contact with wet fabric via annular piezoelectric rings, where water in the liquid form is atomized, transported through microchannels in the disk, and ejected as a mist. In such a system, resonance matching between the actuation portion of the transducer and the portion contacting fabric must be realized, with theoretical results from the developed electromechanical model showing a reduction in energy consumption by 50% when resonance matching is achieved. The electrically coupled distributed parameter model for an annular bimorph piezoelectric transducer is developed for optimization of ultrasonic drying technology. The thickness mode vibrations are shown to dominate the behavior of the system, where the analytically developed model can be optimized to increase the output acceleration of the transducer, thus increasing drying performance. Here, the electromechanical equation developed will be connected to the drying rates of fabrics in contact with said vibrations, where the novelty of the coupled equations and its description of the physics of ultrasonic drying will be discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Quantifying dispersity in size and shape of nanoparticles from small-angle scattering data using machine learning based CREASE

Here, we use machine learning (ML) enhanced computational reverse engineering analysis of scattering experiments (CREASE) to interpret small-angle X-ray scattering (SAXS) data obtained from a system of nanoparticles without a priori knowledge of their exact shapes (e.g. spheres or ellipsoids), sizes (0.5–50 nm) and distributions. The SAXS measurements yielded three categories of scattering profiles exhibiting 'strong', 'weak' and 'no' features. Diminishing features (e.g. broadening or disappearing peaks) in scattering profiles have always been attributed to the presence of significant dispersity in the system. Such featureless SAXS data are not suitable for traditional analysis using analytical models. If one were to fit a relevant analytical model (e.g. the lmfit analytical model for polydisperse spheres) to these 'weak' and 'no' SAXS profiles from our nanoparticle systems, one would obtain non-unique interpretations of the data. Relying on electron microscopy to identify the distributions of nanoparticle shapes and sizes is also unfeasible, especially in high-throughput synthesis and characterization loops. In such situations, to identify the distributions of particle sizes and shapes that could be present in the sample, one must rely on methods like ML-CREASE to interpret the data quickly and output all relevant interpretations about the structure present in the system. The ML-CREASE optimization loop takes the experimental scattering profile as input and outputs multiple candidate solutions whose computed scattering profiles match the SAXS profile input. The ML-CREASE method outputs distributions of relevant structural features, such as the volume fraction of the nanoparticles in the system and the mean and standard deviation of the particle size and aspect ratio, assuming a type of distribution (e.g. normal, log-normal) for size and aspect ratio. We find that, for the SAXS profiles analyzed here, accounting for the shape dispersity along with size dispersity of the nanoparticles using ML-CREASE improved the match between the computed scattering profiles and input experimental profiles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

The ETROC2 as the Final Version for CMS Endcap Timing Layer (ETL) Upgrade

The ETROC (Endcap Timing Readout Chip) is being developed for the LGAD-based CMS Endcap Timing Layer (ETL) at HL-LHC. The ETL on each side of the interaction region will be instrumented with a two-disk system of MIP-sensitive LGAD (Low Gain Avalanche Diodes) silicon devices, read out by ETROCs for precision timing measurement with down to ~30 ps timing resolution per track. The ETROC is designed to handle a 16 x 16 pixel cell matrix, with each pixel being 1.3 mm x 1.3 mm to match the LGAD sensor pixel size. The front-end design for preamplifier and discriminator has been specifically optimized for the reduced LGAD signals, with enough flexibilities to meet the ETL specific needs for time resolution, power budget and radiation profile. The ETROC chip is implemented in a commercial 65nm CMOS process. Each channel consists of a preamplifier, a discriminator, a TDC used for TOA (Time Of Arrival) and TOT (Time Over Threshold) measurements, and a memory for data storage and readout. An in-pixel auto threshold calibration is included, along with a self-testing pattern generator. The TOT is used for time-walk correction of the TOA measurement. The detailed hit information (TOA and TOT) from each cell will be read out from a local circular buffer after each Level-1 Accept (about 1 MHz). In addition, a charge injection circuit is implemented to allow for testing and calibration. For more detailed monitoring of the signal pulses, waveform sampling circuits are included for one pixel. The clock distribution is based on a 16x16 H-tree design with a shielding structure to alleviate potential interference. The global peripheral circuits include a PLL, a phase shifter, an I2C slave controller, a fast control block, a global readout, and a data driver along with an efuse and temperature sensor. The ETROC builds event data frames for each L1A selected event and is also capable of providing L1 trigger information for user-defined delayed hits. The main design challenge is how to extract precision timing information from the small LGAD signals in the presence of high irradiation fluence, while keeping the power consumption and digital activity low. The ETL design goal for the time resolution of 50 ps per hit is required to achieve a 35 ps arrival time measurement for a MIP particle, which has its track registered in two ETL disk layers. The LGAD contribution is known to be about 30 ps, this means that the jitter from the ETROC has to be kept below 40 ps. The ETROC2 is the first full size full functionality prototype design fully compatible with the final chip specifications for CMS ETL and now becomes the final version. The ETROC2 chips have been extensively tested. We will present here new testing results including the bump bonding yield improvement study, the time walk correction (TWC) generality study with one pixel TWC applying to all pixels, the final SEU testing using both heavy ion and proton beam, more beam test studies including different sensors, and readiness for the ETROC2 production for CMS ETL upgrade.

Liu, Tiehui [Fermilab] (ORCID:0009000765225605)↗

NASA NTRS1976

Holographic Recording Materials Development

Organic photorefractive materials were evaluated for application in a reversible holographic memory system. Representative indigo and thioindigo derivatives and several stilbene derivatives were studied as well as 15, 16-dialkyldihydropyrene derivatives the following goals were achieved: (1) the successful writing of phase holograms in a thioindigo/polymer gel system, (2) the successful writing and erasing of phase holograms in a variety of indigo/polymer gel and indigo/solid polymer systems, and (3) the identification of indigoid dyes and 15, 16-dialkyldihydropyrene derivatives as materials potentially suitable for utilization in an operational system. Photochemical studies of the stilbene, indigo, thioindigo, and dialkyldihydropyrene derivatives in solution and in a variety of polymer matrix materials were conducted with the goal of optimizing the photorefractive behavior of the chemical system as a whole. The spectroscopic properties required of optimal photorefractive materials were identified, and it was shown that both the indigoid dyes and the dialkyldihydropyrenes closely match the required properties.

Verber, C. M.↗

NASA NTRS1985

Periodic binary sequences with very good autocorrelation properties

Computer searches were performed using both an 8086 microprocessor and a Cyber 750 mainframe to find repeated binary phase coded waveforms with very good matched and mismatched autocorrelation properties. The best results for every period up to 64 are given. Sequences with optimal peak sidelobes were discovered for each of these periods. These sequences have extensive applications in radar and communications, particularly in situations when there are very unfavorable signal-to-noise ratios. The best sequence of period 64 when processed using a mismatched filter giving no sidelobes has a reduction in the main lobe of less than 0.23 dB.

Tyler, S.↗

NASA NTRS1989

Locally optimal-digital redesign of continuous-time systems

This paper presents a new optimal digital redesign technique for finding a dynamic digital control law from the given continuous-time counterpart by minimizing a local quadratic performance index. The quadratic performance index is chosen as the integral of the weighted squared difference between the states of the original closed-loop system and those of the digitally controlled closed-loop system at any instant between each sampling period. The developed optimal digital redesign control law enables the states of the digitally controlled closed-loop system 10 closely match those of the original closed-loop system at any instant between each sampling period, and it can easily be implemented using microcomputers with a relatively large sampling period.

Shieh, Leang-San↗

NASA NTRS2003

Estimation of Complex Permittivity of Composite Multilayer Material at Microwave Frequency Using Waveguide Measurements

A simple method is presented to estimate the complex dielectric constants of individual layers of a multilayer composite material. Using the MatLab Optimization Tools simple MatLab scripts are written to search for electric properties of individual layers so as to match the measured and calculated S-parameters. A single layer composite material formed by using materials such as Bakelite, Nomex Felt, Fiber Glass, Woven Composite B and G, Nano Material #0, Cork, Garlock, of different thicknesses are tested using the present approach. Assuming the thicknesses of samples unknown, the present approach is shown to work well in estimating the dielectric constants and the thicknesses. A number of two layer composite materials formed by various combinations of above individual materials are tested using the present approach. However, the present approach could not provide estimate values close to their true values when the thicknesses of individual layers were assumed to be unknown. This is attributed to the difficulty in modelling the presence of airgaps between the layers while doing the measurement of S-parameters. A few examples of three layer composites are also presented.

Deshpande, Manohar D.↗

NASA NTRS2005

Investigation of the Carbon Arc Source as an AM0 Solar Simulator for Use in Characterizing Multi-Junction Solar Cells

The operation of multi-junction solar cells used for production of space power is critically dependent on the spectral irradiance of the illuminating light source. Unlike single-junction cells where the spectral irradiance of the simulator and computational techniques may be used to optimized cell designs, optimization of multi-junction solar cell designs requires a solar simulator with a spectral irradiance that closely matches AM0.

Xu, Jianzeng↗