Synthesis of Casimiroin and Optimization of Its Quinone Reductase 2 and Aromatase Inhibitory Activities
Abstract not provided
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided
Mesoporous carbon (MC) with tunable pore sizes (22nm, 12nm, 7nm, and 3nm) and pore volumes (from 1.3 to 4.8 cc/g) containing sulfur inside the pores were systematically studied as mesoporous carbon-sulfur (MCS) composite electrodes for Li-S batteries. Investigation on these MCS composites reveals that the pore structure has no influence on the battery performance at full sulfur loading conditions (the pore volume is fully filled by sulfur) but the maximum sulfur loading capability is higher for MC with larger pore volume. MC with large pore volumes, partial sulfur filling (part of the pore volume left unfilled), and surface modification, can have reasonably high sulfur loading, improved electrical and ionic contacts of sulfur with MC and with electrolytes, which subsequently promotes the battery performance. An initial capacity of ~1250 mAh/g (based on sulfur) and 650 mAh/g capacity retention over 100 cycles were obtained with 50 wt% sulfur loading in the MC with 22nm pore size (4.8 cc/g). When the surface of MCS was coated with Clevios P to reduce the dissolve of polysulfide anions in electrolytes, it exhibits a high initial discharge capacity of ~1390 mAh/g and improved cycling stability with capacity retention of ~840 mAh/g over 100 cycles. The reported correlation among the structure, sulfur filling, surface modification and the electrochemical performance of the MCS composite cathodes provides guidance in designing new electrodes for lithium-sulfur batteries
Quantitative electroluminescence (EL) and luminescent coupling (LC) analysis, along with more conventional characterization techniques, are combined to completely characterize the subcell JV curves within a fourjunction (4J) inverted metamorphic solar cell (IMM). The 4J performance under arbitrary spectral conditions can be predicted from these subcell JV curves. The internal radiative efficiency (IRE) of each junction has been determined as a function of current density from the external radiative efficiency using optical modeling, but this required the accurate determination of the individual junction current densities during the EL measurement as affected by LC. These measurement and analysis techniques can be applied to any multijunction solar cell. The 4J IMM solar cell used to illustrate these techniques showed excellent junction quality as exhibited by high IRE and a one-sun AM1.5D efficiency of 36.3%. This device operates up to 1000 suns without limitations due to any of the three tunnel junctions.
A method for achieving good position resolution of low-intensity electron signals using a microchannel plate resistive anode detector is demonstrated. Electron events at a rate of 7 counts s{sup −1} are detected using a Z-stack microchannel plate. The dependence of position resolution on both the distance and the potential difference between the microchannel plate and resistive anode is investigated. Using standard commercial electronics, a measured position resolution of 170 μm (FWHM) is obtained, which corresponds to an intrinsic resolution of 157 μm (FWHM)
Not Available
Abstract not provided
The researchers extensively studied the effects of annealing or thermal history of cell process on the minority carrier lifetimes of FZ n-type c-Si wafers with various i-layer thicknesses from 5 to 60 nm, substrate temperatures from 100 to 350 degrees C, doped layers both p- and n-types, and transparent conducting oxide (TCO).
Abstract Not Provided
Explore the source record for details and available documents.
The conventional electrolyte of 1 m lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in dimethyl sulfoxide (DMSO) is unstable against the Li metal anode and therefore cannot be used directly in practical Li–O 2 batteries. Here, we demonstrate that a highly concentrated electrolyte based on LiTFSI in DMSO (with a molar ratio of 1:3) can greatly improve the stability of the Li metal anode against DMSO and significantly improve the cycling stability of Li–O 2 batteries. This highly concentrated electrolyte contains no free DMSO solvent molecules, but only complexes of (TFSI − ) a Li + (DMSO) b (where a + b = 4), and thus enhances their stability with Li metal anodes. In addition, such salt–solvent complexes have higher Gibbs activation energy barriers than the free DMSO solvent molecules, indicating improved stability of the electrolyte against the attack of superoxide radical anions. Therefore, the stability of this highly concentrated electrolyte at both Li metal anodes and carbon‐based air electrodes has been greatly enhanced, resulting in improved cycling performance of Li–O 2 batteries. The fundamental stability of the electrolyte in the absence of free‐solvent against the chemical and electrochemical reactions can also be used to enhance the stability of other electrochemical systems.
The primary function of the ionomers that are incorporated into fuel cell electrode catalyst layers is to provide pathways for ion transport between the catalyst active sites and the electrolyte. This is influenced by many variables, including the ion-exchange capacity, water uptake, and molecular weight. In anion exchange membrane fuel cells (AEMFCs), controlling ionomer water uptake is particularly important and tailoring this property in each electrode is an important consideration when looking to maximize cell performance. In this study, three poly(norbornene) tetrablock copolymer ionomers with a range of physical properties are synthesized and incorporated into AEMFC anode and cathode electrodes. Systematic electrode engineering with these ionomers allows the peak power density to be increased by 100% (1.6 W cm -2 → 3.2 W cm -2 ) and the current density at 0.2 V to be increased by 59% (5.9 A cm -2 → 9.4 A cm -2 ). Moreover, the top-performing electrode configuration is tested in an operating AEMFC at the US Department of Energy defined current density of 600 mA cm -2 for 2000 h, showing a record-low voltage decay rate of 15.36 µV h -1 – only 3.65% –a over 2000 h. Here, this work sets a new bar for AEMFCs, reporting the best combination of performance and durability of any AEMFC to date.
Explore the source record for details and available documents.
FLASH is a multiphysics multiscale adaptive mesh refinement (AMR) code originally designed for simulation of reactive flows often found in Astrophysics. With its wide user base and flexible applications configuration capability, FLASH has a dual task of maintaining scalability and portability in all its solvers. The scalability of fully explicit solvers in the code is tied very closely to that of the underlying mesh. Others such as the Poisson solver based on a multigrid method have more complex scaling behavior. Multigrid methods suffer from processor starvation and dominating communication costs at coarser grids with increase in the number of processors. In this paper, we propose a combination of uniform grid mesh with AMR mesh, and the merger of two different sets of solvers to overcome the scalability limitation of the Poisson solver in FLASH. The principal challenge in the proposed merger is the efficiency of the communication algorithm to map the mesh back and forth between uniform grid and AMR. We present two different parallel mapping algorithms and also discuss results from performance studies of the two implementations. Copyright © 2012 John Wiley & Sons, Ltd.
Explore the source record for details and available documents.