Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES - BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Flat Plate Cascades at Supersonic Speed

A brief review of exact two-dimensional supersonic flow theory and Ackeret's linearized theory are first presented. The lift and drag coefficients of a cascade of flat plates are calculated exactly and compared to those obtained using the linearized theory. The forces on the cascade are determined for unsteady inlet flow. The flat plate cascade theory is extended to compute the efficiency of a supersonic propeller with friction and finite blade thickness.

FLOW - PLATES, FLAT - SUPERSONIC↗
NASA NTRS1994

Noise Temperature Contribution of a Dichroic Plate in a Beam-Waveguide Antenna System

A 34m diameter antenna, built for NASA/JPL in 1990 at Goldstone, California, utilizes a beam-waveguide (BWG) design. It was discovered that if a dichroic plate is installed in a BWG antenna environment, high noise temperatures can result if the receiver system passband is greater than the passband for which the plate was designed. A method is presented for accurately calculating dichroic plate noise temperature for these conditions.

Dichroic Plate Beam-Waveguide Antenna↗
NASA NTRS1995

Technology Transfer of Plate Wave NDE to Ultrasonic Rotary Actuation

Plate waves have been the subject of NDE research and applications. These waves, also known as guided waves of Lamb waves, are formed in two distinct modes--symmetric and antisymmetric --depending on their vibration characteristics in relation to the plate geometry. Experiments have corroborated the predictions for various plate wave modes, allowing the elastic properties of composite materials and adhesive bonded joints to be determined.

joints↗
NASA NTRS1950

Stress and strain concentration at a circular hole in an infinite plate

The theory of elasticity shows that the maximum stress at a circular hole in an infinite plate in tension is three times the applied stress when the material remains elastic. The effect of plasticity of the material is to lower this ratio. This paper considers the theoretical problem of the stress distribution in an infinitely large sheet with a circular hole for the general case where the material may have any stress-strain curve. The plate is assumed to be under uniform tension at a large distance from the hole. The material is taken to be isotropic and incompressible. (author)

THEORIES - ELASTICITY↗
NASA NTRS1971

Sharp flat plate heat transfer in helium at Mach numbers of 22.8 to 86.8 and in corner flow with air at Mach number of 19

Surface heat transfer rates were measured on a sharp flat plate at zero angle of attack in a hypersonic shock tunnel. The density and leading edge Knudsen number were varied to span the continuum to near free molecule regimes. The strong interaction parameter varied from 11 to 16,000 with Knudsen numbers from 0.56 to 17.1 respectively. Local heat transfer rates in the corner flow region produced by the intersection of two perpendicular flat plates with sharp leading edges were determined for various flow densities. The strength of the shock wave from the vertical plate was varied by adjusting the angle of attack from 0 to 5 deg. The unit Reynolds number varied from 1,000 to 17,200 and the Knudsen numbers from 1.6 to 27. The strong interaction parameter varied from 14 to 500.

Nagamatsu, H. T.↗
NASA NTRS1971

An F1 Schmidt satellite camera and the methods of plate measurement and reduction

The f1 Hewitt camera is a field flattened Schmidt system of 60cm aperture. The salient features of this equipment are briefly described. Details of the methods of plate measurement are then given. The plate reduction is carried out in two stages. The plate is first calibrated using the photogrammetric method. The formulae usually quoted have been extended to take account of the large distortion introduced by the field flattening lens. In the second stage, the satellite measurements are reduced to satellite positions corrected for refraction, aberration, and when necessary, phase.

Hewitt, J.↗
NASA NTRS1971

Development of nondestructive testing techniques for plated-through holes in multilayer printed circuit boards

The development of a nondestructive test with the capability to interrogate plated-through holes as small as 0.51 millimeters inside diameter is discussed. The system can detect defects such as holes, voids, cracks, and thin spots that reduce the current carrying capability of plates-through interconnects by 20 percent or more. Efforts were directed toward the design and fabrication of magnetic circuitry mutual coupling probes and to evaluate the effectiveness of these devices for detecting in multilayer board plated-through holes.

Anthony, P. L.↗
NASA NTRS1972

Fabrication and testing of scatter plates for interferometry

Scatter plate interferometry has become a reliable method of measuring surface configurations of telescope mirrors and other optical components. The scatter plate used in an instrument should be of optimum quality if the surface it is being used to measure is to be of high accuracy. Tests were performed and results show that, although many scatter plates would function, few were of the optimum quality necessary. These few were of the 180 grit group, using 35- and 30-s exposures, which are figures derived from calculations.

Pour, J. J., Sr.↗
NASA NTRS1971

Annealing effects in plated-wire memory elements. I - Interdiffusion of copper and Permalloy.

Results of investigations using X-ray diffraction and electron-beam microprobe techniques have shown that copper and Permalloy platings interdiffuse at low temperatures when plated-wire memory elements are annealed for times as short as 50 hr. Measurable interdiffusion between Permalloy platings and gold substrates does not occur in similar conditions. Both magnetic and compositional changes during aging are found to occur by a thermally activated process with activation energies around 38 kcal/mol. It is shown, however, that copper-diffusion and magnetic-dispersion changes during aging are merely concurrent processes, neither being the other's cause.

Knudson, C. I.↗
NASA NTRS1972

A non-linear dynamic lumped-parameter model of a rectangular plate.

A lumped-parameter model of a rectangular plate is developed by assuming fundamental mode solutions and using Hamilton's Principle and the Euler equations to set up the differential equation of motion for the system. The plate theory used may be described as the dynamic analogue of the von Karman large-deflection theory. Four sets of symmetrical boundary conditions are considered with the restriction of uniform pressure dynamic loads. The model takes the form of a mass on a cubic-hardening spring with each term defined by algebraic expressions of the plate parameters. The results for some specific problems are compared with two previous solutions. This method is less accurate but simpler to develop and apply.

Bayles, D. J.↗
NASA NTRS1972

Strongly coupled stress waves in heterogeneous plates.

Consideration of coupled stress waves generated by an impulsive load applied at one end of a semiinfinite plate. For the field equations governing the one-dimensional coupled waves a hyperbolic system of equations is obtained in which a strong coupling in the second derivatives exists. The method of characteristics described by Chou and Mortimer (1967) is extended to cover the case of strong coupling, and a study is made of the transient stress waves in a semiinfinite plate subjected to an initial step input. Coupled discontinuity fronts are found to propagate at different velocities. The normal plate stress and the bending moment at different time regimes are illustrated by graphs.

Wang, A. S. D.↗
NASA NTRS1972

Chladni's patterns for random vibration of a plate.

A typical Chladni pattern for pure tone excitation is shown. The aluminum plate used is clamped in a steel frame. The measured fundamental frequency is 13 Hz. The random vibration of a taut spring is discussed together with the random vibration of a thin plate and approximations for the modal sum. The Chladni pattern for wide band excitation applied at a certain point is shown together with the predicted distribution of mean square velocity as a function of the y coordinate of the plate and the experimentally measured distribution of mean square velocity as a function of y.

Crandall, S. H.↗
NASA NTRS1972

An analysis of the relaxation of laminar boundary layer on a flat plate after passage of an interface with application to expansion-tube flows

The relaxation of the accelerating-gas boundary layer to the test-gas boundary layer over a flat plate in an expansion tube is analyzed. Several combinations of test gas and acceleration gas are considered. The problem is treated in two conically similar limits: (1) when the time lag between the arrival of the shock and the interface at the leading edge of the plate is very large, and (2) when this lag is negligible. The time-dependent laminar-boundary-layer equations of a binary mixture of perfect gases are taken as the flow-governing equations. This coupled set of differential equations, written in terms of the Lam-Crocco variables, has been solved by a line-relaxation finite-difference techniques. The results presented include the Stanton number and the local skin-friction coefficient as functions of shock Mach number and the nondimensional distance-time variable. The results indicate that more than 95 percent of the test-gas boundary layer exists over a length, measured from the leading edge of the plate, equal to about three-tenths of the distance traversed by the interface in the free stream.

Gupta, R. N.↗
NASA NTRS1972

Elasto-plastic bending of cracked plates, including the effects of crack closure

A capability for solving elasto-plastic plate bending problems is developed using assumptions consistent with Kirchhoff plate theory. Both bending and extensional modes of deformation are admitted with the two modes becoming coupled as yielding proceeds. Equilibrium solutions are obtained numerically by determination of the stationary point of a functional which is analogous to the potential strain energy. The stationary value of the functional for each load increment is efficiently obtained through use of the conjugate gradient. This technique is applied to the problem of a large centrally through cracked plate subject to remote circular bending. Comparison is drawn between two cases of the bending problem. The first neglects the possibility of crack face interference with bending, and the second includes a kinematic prohibition against the crack face from passing through the symmetry plane. Results are reported which isolate the effects of elastoplastic flow and crack closure.

Jones, D. P.↗
NASA NTRS1972

Plating methods, a survey

Results are presented of a comprehensive search of the literature available, much of which has been generated by the research centers of NASA and its contractors, on plating and coating methods and techniques. Methods covered included: (1) electroplating from aqueous solutions; (2) electroplating from nonaqueous solutions; (3) electroplating from fused-salt baths; (4) electroforming; (5) electroless plating, immersion plating, and mirroring; (6) electroplating from gaseous plasmas; and (7) anodized films and conversion coatings.

Berkowitz, J. B.↗